SERIAL_SGI_IOC4 and BLK_DEV_SGIIOC4 depend upon SGI_IOC4, and
SERIAL_SGI_IOC3 depends upon SGI_IOC3. Currently the definitions
are out of order in the config sequence.
Fix by including drivers/sn/Kconfig immediately after SGI_SN,
upon which SGI_IOC4 and SGI_IOC3 depend.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix asm_offsets.c and entry.S to work with the new power save code.
Changes in arch/powerpc needed to exist in arch/ppc as well since the
idle code is shared by both ppc and powerpc..
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Every time a new syscall gets added, a BUILD_BUG_ON in
arch/powerpc/platforms/cell/spu_callbacks.c gets triggered.
Since the addition of a new syscall is rather harmless,
the error should just be removed.
While we're here, add sys_tee to the list and add a comment
to systbl.S to remind people that there is another list
on powerpc.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new i2c implementation for PowerMac has a regression that causes the
hardware to go out of state when probing non-existent devices. While
fixing that, I also found & fixed a couple of other corner cases. This
fixes booting with a pbbuttons version that scans the i2c bus for an LMU
controller among others. Tested on a dual G5 with thermal control (which
has heavy i2c activity) with no problem so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Turn on the DART already at 1GB. This is needed because of crippled
devices in some systems, i.e. Airport Extreme cards, only supporting
30-bit DMA addresses.
Otherwise, users with between 1 and 2GB of memory will need to manually
enable it with iommu=force, and that's no good.
Some simple performance tests show that there's a slight impact of
enabling DART, but it's in the 1-3% range (kernel build with disk I/O
as well as over NFS).
iommu=off can still be used for those who don't want to deal with the
overhead (and don't need it for any devices).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some devices don't support full 32-bit DMA address space, which we currently
assume. Add the required mask-passing to the IOMMU allocators.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes following compile time warnings:
drivers/pci/pci-sysfs.c: In function `pci_read_legacy_io':
drivers/pci/pci-sysfs.c:257: warning: implicit declaration of function `ia64_pci_legacy_read'
drivers/pci/pci-sysfs.c: In function `pci_write_legacy_io':
drivers/pci/pci-sysfs.c:280: warning: implicit declaration of function `ia64_pci_legacy_write'
It also fixes wrong definition of ia64_pci_legacy_write (type of `bus' is not
`pci_dev', but `pci_bus').
Signed-Off-By: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is a trivial patch to remove following compile time warning:
arch/ia64/ia32/../../../fs/binfmt_elf.c:508: warning: 'randomize_stack_top' defined but not used
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is back again. Offending patch is x86_64-mm-hotadd-reserve.patch
arch/arm/kernel/setup.c:435: error: conflicting types for 'add_memory'
include/linux/memory_hotplug.h:102: error: previous declaration of 'add_memory' was here
arch/arm/kernel/setup.c:435: error: conflicting types for 'add_memory'
include/linux/memory_hotplug.h:102: error: previous declaration of 'add_memory' was here
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The irq2gpio array was recently converted from an array of ints to an
array of chars (by patch 3368/1.) However, this array contains elements
that are -1, and on ARM, the char type is unsigned by default, so this
patch broke the GPIO check in ixp4xx_set_irq_type.
Change the 'char' to be a 'signed char' to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AMD K7/K8 CPUs only save/restore the FOP/FIP/FDP x87 registers in FXSAVE
when an exception is pending. This means the value leak through
context switches and allow processes to observe some x87 instruction
state of other processes.
This was actually documented by AMD, but nobody recognized it as
being different from Intel before.
The fix first adds an optimization: instead of unconditionally
calling FNCLEX after each FXSAVE test if ES is pending and skip
it when not needed. Then do a x87 load from a kernel variable to
clear FOP/FIP/FDP.
This means other processes always will only see a constant value
defined by the kernel in their FP state.
I took some pain to make sure to chose a variable that's already
in L1 during context switch to make the overhead of this low.
Also alternative() is used to patch away the new code on CPUs
who don't need it.
Patch for both i386/x86-64.
The problem was discovered originally by Jan Beulich. Richard
Brunner provided the basic code for the workarounds, with contribution
from Jan.
This is CVE-2006-1056
Cc: richard.brunner@amd.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the "apm: set display: Interface not engaged" error on Armada laptops
again.
Jordan said:
I think this is fine. It seems to me that this may be the fault of one or
both of the APM solutions handling this situation in a non-standard way, but
since APM is used very little on the Geode, and I have direct access to our
BIOS folks, if this problem comes up with a customer again, we'll solve it
from the firmware.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: "Jordan Crouse" <jordan.crouse@amd.com>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were missing __volatile__ on some bits of asm in the segfault handlers.
On x86_64, this was messing up the move from %rdx to uc because that was
moved to after the GET_FAULTINFO_FROM_SC, which changed %rdx.
Also changed the other bit of asm and the one in the i386 handler to
prevent any similar occurrences.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
UML really wants shared memory semantics form its physical memory map file,
and the place for that is /dev/shm. So move the default, and fix the error
messages to recognize that this value can be overridden.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bits of uml __user annotations lost in merge
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the jmpbuf code. Since softints, we no longer use sig_setjmp, so
the UML_SIGSETJMP wrapper now has a misleading name. Also, I forgot to
change the buffers from sigjmp_buf to jmp_buf.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a patch to support a reboot function for M3A-2170(Mappi-III)
evaluation board.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This modification is required to fix debugging function for m32r targets
with !CONFIG_ISA_DSP_LEVEL2, by unifying 'struct pt_regs' and 'struct
sigcontext' size for all M32R ISA.
Some m32r processor core with !CONFIG_ISA_DSP_LEVEL2 configuration has only
single accumulator a0 (ex. VDEC2 core, M32102 core, etc.), the others with
CONFIG_ISA_DSP_LEVEL2 has two accumulators, a0 and a1.
This means there are two variations of thread context. So far, we reduced
and changed stackframe size at a syscall for their context size. However,
this causes a problem that a GDB for processors with CONFIG_ISA_DSP_LEVEL2
cannot be used for processors with !CONFIG_ISA_DSP_LEVEL2.
From the viewpoint of GDB support, we should reduce such variation of
stackframe size for simplicity.
In this patch, dummy members are added to 'struct pt_regs' and 'struct
sigcontext' to adjust their size for !CONFIG_ISA_DSP_LEVEL2.
This modification is also a one step for a GDB update in future.
Currently, on the m32r, GDB can access process's context by using ptrace
functions in a simple way of register by register access. By unifying
stackframe size, we have a possibility to make use of ptrace functions of
not only a single register access but also block register access,
PTRACE_{GETREGS,PUTREGS}.
However, for this purpose, we might have to modify stackframe structure
some more; for example, PSW (processor status word) register should be
pre-processed before pushing to stack at a syscall, and so on. In this
case, we must update carefully both kernel and GDB at a time...
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Kei Sakamoto <ksakamot@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix section mismatch warnings in x86 cpuid and msr notifier callback
functions. We can't have these as init (discarded) code.
WARNING: arch/x86_64/kernel/cpuid.o - Section mismatch: reference to .init.text: from .data between 'cpuid_class_cpu_notifier' (at offset 0x0) and 'cpuid_fops'
WARNING: arch/x86_64/kernel/msr.o - Section mismatch: reference to .init.text: from .data between 'msr_class_cpu_notifier' (at offset 0x0) and 'msr_fops'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MADV_REMOVE fixes - change the test mapping to be MAP_SHARED instead of
MAP_PRIVATE, as MADV_REMOVE on MAP_PRIVATE maps won't work. Also, use
the kernel's definition of MADV_REMOVE instead of hardcoding it if there
isn't a libc definition.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the minimal fix to make 64-bit UML binaries create 32-bit
compatible COW files and read them.
I've indeed tested that current code doesn't do this - the code gets
SIGFPE for a division by a value read at the wrong place, where 0 is
found.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (47 commits)
[MAINTAINERS] The ham radio code now has website at http://www.linux-ax25.org.
[MIPS] Use __ffs() instead of ffs() for waybit calculation.
[MIPS] Fix Makefile bugs for MIPS32/MIPS64 R1 and R2.
[MIPS] Handle IDE PIO cache aliases on SMP.
[MIPS] Make mips_srs_init static.
[MIPS] MIPS boards: Set HZ to 100.
[MIPS] kgdb: Let gcc compute the array size itself.
[MIPS] FPU affinity for MT ASE.
[MIPS] MT: Improved multithreading support.
[MIPS] kpsd and other AP/SP improvements.
[MIPS] R2: Instruction hazard barrier.
[MIPS] Fix genrtc compilation.
[MIPS] R2: Implement shadow register allocation without spinlock.
[MIPS] Fix VR41xx build errors.
[MIPS] Fix tx49_blast_icache32_page_indexed.
[MIPS] Enable SCHED_NO_NO_OMIT_FRAME_POINTER for MIPS.
[MIPS] Use "R" constraint for cache_op.
[MIPS] Rewrite all the assembler interrupt handlers to C.
[MIPS] Fix the crime against humanity that mipsIRQ.S is.
[MIPS] Fixup damage done by 22a9835c35.
...
This fixes kernel builds with gcc 3.2 (not 64-bit, that is looking like
it is beyond recovery) and 3.3. With these bugs fixed we now also can
get undo 3b4c4996a0c24da9e6f8be764e3950b756b18cc0 and similar bits for
SMTC that were added in 79cc8007b93838a670b164b8a55ab3e735a12a8b.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the cache index value in tx49_blast_icache32_page_indexed().
This is a damage by de62893bc0 commit.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Saves like 1,600 lines of code, is way easier to debug, compilers
frequently do a better job than the cut and paste type of handlers many
boards had. And finally having all the stuff done in a single place
also means alot of bug potencial for the MT ASE is gone.
The only surviving handler in assembler is the DECstation one; I hope
Maciej will rewrite it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some things were renamed because the PPC variant of the MV-643XX now
uses the same header and the Jaguar code didn't catch up on that.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes dependencies of HUGETLB_PAGE_SIZE_64K
Signed-off-by: Jean-Luc Lger <jean-luc.leger@dspnet.fr.eu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a check-after-use introduced by commit
4211a30349 and spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove a duplicate NULL pointer check introduced by commit
4211a30349
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Dave Jones <davej@redhat.com>
Patch from Richard Purdie
corgi_ssp_probe() should not access GPDR directly but should use
pxa_gpio_mode() which has appropriate locking and other safeguards.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Move platform_scoop_config from the SharpSL scoop PCMCIA driver to
the SCOOP driver. This avoids build failures when PCMCIA is not built
or is modular (scoop.c itself cannot be modular).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tee was already there for some reason for native 64bit, but
sys_sync_file_range was missing. Also add it to the compat layer.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Start booting into the capture kernel after an Oops if system is in a
unrecoverable state. System will boot into the capture kernel, if one is
pre-loaded by the user, and capture the kernel core dump.
o One of the following conditions should be true to trigger the booting of
capture kernel.
- panic_on_oops is set.
- pid of current thread is 0
- pid of current thread is 1
- Oops happened inside interrupt context.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch I submitted earlier to fix disabled LAPIC handling in ACPI
was mismerged for some reason I still don't quite understand. Parts
of it was applied to the wrong function.
This patch fixes it up.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Use correct sequence for putting CPU into nap mode
[PATCH] spufs: fix context-switch decrementer code
[PATCH] powerpc32: Set cpu explicitly in kernel compiles
[PATCH] powerpc/pseries: bugfix: balance calls to pci_device_put
[PATCH] powerpc: Fix machine detection in prom_init.c
[PATCH] ppc32: Fix string comparing in platform_notify_map
[PATCH] powerpc: Avoid __initcall warnings
[PATCH] powerpc: Ensure runlatch is off in the idle loop
powerpc: Fix CHRP booting - needs a define_machine call
powerpc: iSeries has only 256 IRQs
We weren't using the recommended sequence for putting the CPU into
nap mode. When I changed the idle loop, for some reason 7447A cpus
started hanging when we put them into nap mode. Changing to the
recommended sequence fixes that.
The complexity here is that the recommended sequence is a loop that
keeps putting the cpu back into nap mode. Clearly we need some way
to break out of the loop when an interrupt (external interrupt,
decrementer, performance monitor) occurs. Here we use a bit in
the thread_info struct to indicate that we need this, and the exception
entry code notices this and arranges for the exception to return
to the value in the link register, thus breaking out of the loop.
We use a new `local_flags' field in the thread_info which we can
alter without needing to use an atomic update sequence.
The PPC970 has the same recommended sequence, so we do the same thing
there too.
This also fixes a bug in the kernel stack overflow handling code on
32-bit, since it was causing a value that we needed in a register to
get trashed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The at91_cf driver got out of sync with certain changes in the PCMCIA
layer, notably getting rid of some duplication of data ... causing the
version merged to kernel.org to fail compiling.
This patch gives the at91_cf platform device a new iomem resource, using
it so this new pcmcia scheme works. It also cleans up some whitepsace
bugs that have accumulated over time (mostly too-long lines).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
commit 5fdef39495
Author: David S. Miller <davem@sunset.davemloft.net>
Date: Fri Apr 14 15:29:32 2006 -0700
[SPARC]: Hook up sys_tee() into syscall tables.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (169 commits)
commit 78a596b449
Author: Adrian Bunk <bunk@stusta.de>
Date: Fri Mar 31 01:38:12 2006 -0800
[PATCH] remove kernel/power/pm.c:pm_unregister()
Since the last user is removed in -mm, we can now remove this long deprecated
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 21440d3133
Author: David Brownell <david-b@pacbell.net>
Date: Sat Apr 1 10:21:52 2006 -0800
[PATCH] dma doc updates
...
I use 2.6.15.6 Linux kernel and found some problems. I have about 100
Linux boxes (all with the same (binary the same) kernel). Last time I have
upgraded all those boxes from 2.4.32 to 2.6.15.6 (first 2.6.15.1, next .2,
.4 and .6) and I have found some problems on VIA based PC's. Probably the
reason of this is that some VIA chipsets are unrecognized by IRQ router.
In line 586 there is: /* FIXME: add new ones for 8233/5 */
There were only a few of chipsets ID's there, some of my VIA chipsets were
not present and kernel used default IRQ router.
I have added three entries, so that the code looks like:
case PCI_DEVICE_ID_VIA_82C596:
case PCI_DEVICE_ID_VIA_82C686:
case PCI_DEVICE_ID_VIA_8231:
case PCI_DEVICE_ID_VIA_8233A:
case PCI_DEVICE_ID_VIA_8235:
case PCI_DEVICE_ID_VIA_8237:
case PCI_DEVICE_ID_VIA_8237_SATA:
/* FIXME: add new ones for 8233/5 */
r->name = "VIA";
r->get = pirq_via_get;
r->set = pirq_via_set;
return 1;
}
The kernel goes fine but I haven't testes it for weeks, I'm just a moment
after reboot :)
One thing is different (better?):
Using previus kernel I had:
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
now I have:
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 11
Maybe it is good idea to add there some more VIA chipsets?
The ones I have added seem to be OK.
From: Grzegorz Janoszka <Grzegorz@Janoszka.pl>
Acked-by: Martin Mares <mj@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'tee' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] splice: add support for sys_tee()
[PATCH] splice: pass offset around for ->splice_read() and ->splice_write()
This patch modifies ia64's show_mem() to walk the vmem_map page tables and
rapidly skip forward across regions where the page tables are missing.
This prevents the pfn_valid() check from causing numerous unnecessary
page faults.
Without this patch on a 512 node 512 cpu system where every node has four
memory holes, the show_mem() call takes 1 hour 18 minutes. With this
patch, it takes less than 3 seconds.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64_wait_for_slaves() was changed in 2.6.17-rc1 to report the slave
state. It incorrectly assumes that all slaves are for MCA, but
ia64_wait_for_slaves() is also called from the INIT monarch handler.
The existing message is very misleading, so correct it.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We found that when the 'decrementer' is saved, the PPE saves the current
time 'csa->suspend_time'. When restoring the 'decrementer', (Step 34)
decrementer seems to be adjusted with the number of cycles th= at a spu
thread has not been running.
In that code it is missing a substract ('-') because 'delta_time' is
assigned a not substracted(see bellow).
Acked-by: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compile the 32bit kernel with -mcpu=powerpc. This reduces the imagesize
when a compiler is used that defaults to -mtune=power4. It inserts lots
of nops to please the 64bit cpu instruction scheduling. But all these nops
are not needed for 32bit kernels.
Example with SLES10 gcc 4.1.0 and arch/powerpc/configs/pmac32_defconfig:
vmlinux vmlinux.strip vmlinux.gz
-O2 4980515 4187528 1846829
-Os 4618801 3827084 1673333
-O2 -mcpu=powerpc 4738851 3945868 1816253
-Os -mcpu=powerpc 4532785 3741068 1664688
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Repeated calls to eeh_remove_device() can result in multiple
(and thus unbalanced) calls to pci_dev_put(). Make sure the
pci_device_put() is called only once (since there was only
one call to the matching pci_device_get()).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In e8222502ee the detection of machine types
in prom_init broke for some machines. We should be checking /device_type
instead of /model. This should make Power3 and Power4 boot again. Haven't
been able to test this. We also need to relocate before comparing.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixed odd function behavior when dev->bus_id does not contain '.' - it
compared that case 0 characters of the string and hereby reported success and
executed callback. Now bus_id's are compared correctly, extra callback
triggering eliminated.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix __initcall return in proc_rtas_init and rtas_init.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since external and decrementer interrupts set the runlatch on, we need
to ensure its set off again in the idle loop. At the moment we dont turn
it off in the inner loop.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Ben Dooks
Fix bad spelling of partition
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The wrong variable is written back to CLKDIVN
register if the USB PLL speed is above 94MHz
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Basically an in-kernel implementation of tee, which uses splice and the
pipe buffers as an intelligent way to pass data around by reference.
Where the user space tee consumes the input and produces a stdout and
file output, this syscall merely duplicates the data inside a pipe to
another pipe. No data is copied, the output just grabs a reference to the
input pipe data.
Signed-off-by: Jens Axboe <axboe@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Prefetch mmap_sem in ia64_do_page_fault()
[IA64] Failure to resume after INIT in user space
[IA64] Pass more data to the MCA/INIT notify_die hooks
[IA64] always map VGA framebuffer UC, even if it supports WB
[IA64] fix bug in ia64 __mutex_fastpath_trylock
[IA64] for_each_possible_cpu: ia64
[IA64] update HP CSR space discovery via ACPI
[IA64] Wire up new syscalls {set,get}_robust_list
[IA64] 'msg' may be used uninitialized in xpc_initiate_allocate()
[IA64] Wire up new syscall sync_file_range()
Surprising that it still worked at all with this - yes it was
tested.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nobody should pass NULL here. Could in theory make it a BUG,
but the NULL pointer oops will do as well.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's not actually needed and would break non power of two number
of cores.
Follows similar earlier x86-64 patch.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Linus it is useless now because entry.S should
handle it correctly in all cases.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When nolapic was passed or the local APIC was disabled
for another reason ACPI would still parse the IO-APICs
until these were explicitely disabled with noapic.
Usually this resulted in a non booting configuration unless
"nolapic noapic" was used.
I also disabled the local APIC parsing in this case, although
that's only cosmetic (suppresses a few printks)
This hopefully makes nolapic work in all cases.
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bugzilla Bug 6299:
A pixel size of 8 bits produces wrong logo colors in x86_64.
The driver has 2 methods for setting the color map, using the protected
mode interface provided by the video BIOS and directly writing to the VGA
registers. The former is not supported in x86_64 and the latter is enabled
only in i386.
Fix by enabling the latter method in x86_64 only if supported by the BIOS.
If both methods are unsupported, change the visual of vesafb to
STATIC_PSEUDOCOLOR.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While cleaning up parisc_ksyms.c earlier, I noticed that strpbrk wasn't
being exported from lib/string.c. Investigating further, I noticed a
changeset that removed its export and added it to _ksyms.c on a few more
architectures. The justification was that "other arches do it."
I think this is wrong, since no architecture currently defines
__HAVE_ARCH_STRPBRK, there's no reason for any of them to be exporting it
themselves. Therefore, consolidate the export to lib/string.c.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-finline-limit might have been required for older compilers, but nowadays
it does no longer make sense.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since on some 64-bit systems __u64 is rightfully defined to unsigned long and
GCC recognizes anyway unsigned long and unsigned long long as different, fix
some types back to being unsigned long long to avoid warnings and errors (for
prototype mismatch) on those systems.
Thanks to the report by Wesley Emeneker wesleyemeneker (at) google (dot) com
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Parallel make failed once for me - fix this by adding the appropriate command
(mkdir before creating a link in that dir).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The call to local_save_flags seems bogus since it is followed by
local_irq_restore, and it's intended to lock the list from concurrent
mconsole_interrupt invocations.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch this proc from storing 4k of data (a whole path) on the stack to
keeping it on the heap.
Maybe it's not called in process context but only in early boot context (where
in UML you have a normal process stack on the host) but just to be safe, fix
it.
While at it some little readability simplifications.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Little fix for error paths in this code.
- Some bug come from conversion to os-Linux (open() doesn't follow the
kernel -errno return convention, while the old code called os_open_file()
which followed it). This caused the wrong return code to be printed.
- Then be more precise about what happened and do some whitespace fixes.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an hang on a pipe when run_helper() fails when called by change_tramp()
(i.e. when calling uml_net) - reproduced the bug and verified this fixes it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move a call to kfree on a local variable out of a spinlock - there's no need
to have it in. Done on a just merged patch.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sparse checker work for userspace files - it normally gets -nostdinc
separately, so avoid having it for userspace files. Also, add -D$(SUBARCH)
for multiarch hosts (i.e. AMD64 with compatibility headers).
It works, the only problem is a bit of bogus warnings for system headers, but
they're not too many.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed this for a compilation-time warning, so I'm fixing it even for TT mode
- this is not put_user, but copy_to_user, so we need a pointer to sp, not sp
itself (we're trying to write the word pointed to by the "sp" var.).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the prototype from arch-generic to arch-specific includes because on
x86_64 these functions are two static inlines.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some functions are exported twice in current code - remove the excess export.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that GCC warns about format errors, fix them. Nothing able to cause a
crash, however.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the format attribute to prototypes so GCC warns about improper usage.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix two harmless warnings in 64-bit compilation (the 2nd doesn't trigger for
now because of a missing __attribute((format)) for cow_printf, but next
patches fix that).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Correct the layout of all header versions - make all them well-specified
for any external event. As we don't have 1-byte or 2-byte wide fields, the
32-bit layout (historical one) has no extra padding, so we can safely add
__attribute__((packed)).
- Add detection and reading of the broken 64-bit COW format which has been
around for a while - to allow safe migration to the correct 32-bit format.
Safe detection is possible, thanks to some luck with the existing format,
and it works in practice.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the minimal fix to make 64-bit UML binaries create 32-bit compatible
COW files and read them. I've indeed tested that current code doesn't do this
- the code gets SIGFPE for a division by a value read at the wrong place,
where 0 is found.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change memory hotplug to use GFP_NOWAIT instead of GFP_ATOMIC, so that it
will grab memory without sleeping, but doesn't try to use the emergency
pools.
A small list initialization suggested by Daniel Phillips - don't initialize
lists which are just about to be list_add-ed.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two small TLS fixes -
arch/um/os-Linux/sys-i386/tls.c uses errno and -E* so it should include
errno.h
__setup_host_supports_tls returns 1, but as an initcall, it should return 0
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update {get,put}_user macros for m32r kernel.
- Modify get_user to use __get_user_asm macro, instead of __get_user_x macro.
- Remove arch/m32r/lib/{get,put}user.S.
- Some cosmetic updates.
I would like to thank NIIBE Yutaka for his reporting about the m32r kernel's
security problem in {get,put}_user macros.
There were no address checking for user space access in {get,put}_user macros.
;-)
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: NIIBE Yutaka <gniibe@fsij.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a boot problem of the m32r SMP kernel 2.6.16-rc1-mm3 or
later.
In this patch, cpu_possible_map is statically initialized, and cpu_present_map
is also copied from cpu_possible_map in smp_prepare_cpus(), because the m32r
architecture has not supported CPU hotplug yet.
Signed-off-by: Hayato Fujiwara <fujiwara.hayato@renesas.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've encountered two problems with 2.6.16 and newer kernels on my API CS20
(dual 833MHz Alpha 21264b processors). The first is the kernel OOPSing
because of a NULL pointer dereference while trying to populate SysFS with the
CPU information. The other is that only one processor was being brought up.
I've included a small Alpha-specific patch that fixes both problems.
The first problem was caused by the CPUs never being properly registered using
register_cpu(), the way it's done on other architectures.
The second problem has to do with the removal of hwrpb_cpu_present_mask in
arch/alpha/kernel/smp.c. In setup_smp() in the 2.6.15 kernel sources,
hwrpb_cpu_present_mask has a bit set for each processor that is probed, and
afterwards cpu_present_mask is set to the cpumask for the boot CPU. In the
same function of the same file in the 2.6.16 sources, instead of
hwrpb_cpu_present_mask being set, cpu_possible_map is updated for each probed
CPU. cpu_present_mask is still set to the cpumask of the boot CPU afterwards.
The problem lies in include/asm-alpha/smp.h, where cpu_possible_map is
#define'd to be cpu_present_mask.
Cleanups from: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
- cpu_present_mask and cpu_possible_map are essentially the same thing
on alpha, as it doesn't support CPU hotplug;
- allocate "struct cpu" only for present CPUs, like sparc64 does.
Static array of "struct cpu" is just a waste of memory.
Signed-off-by: Brian Uhrain <buhrain@rosettastone.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Geode GX/LX should enable X86_TSC. Pointed out by Adrian Bunk.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since several subarchs depend on SMP, the SMP option should be above the
subarch selection.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
John Z. Bohach <jzb@aexorsyst.com> found this bug:
If the board has more than 32 PCI busses on it, the mptable bus array will
overwrite its bounds for the PCI busses, and stomp on anything that's after
it.
Prevent possible table overflow and unknown data corruption. Code is in an
__init section so it will be discarded after init.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the DOUBLEFAULT option from the top-level menu to the EMBEDDED menu.
Only applicable to X86_32.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print summary registers (EIP and SS:ESP only) as last death info. This
makes this important data visible in case it had scrolled off the top of
the display. Similar to what x86_64 does. Suggested by Andi Kleen.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switching to automatic bigsmp causes a misleading error message, that more
then 8 cpus are detected, and user needs to select either X86_GENERICARCH
or X86_BIGSMP to handle.
Reason is we switched to bigsmp to avoid IP race when new cpu is comming
up. [bigsmp is nothing but using physical flat mode that can work for 1 ..
255 cpus] [default is X86_PC, that uses logical flat mode up to 8 CPUs
max] Current x86_64 code uses bigsmp as default when hotplug is enabled.
It would be preferable to make bigsmp as default, and work the dependencies
of other related code like SMP_SUSPEND, and some related to memory hotplug
code for i386.
Current logical flat mode doesnt use shortcuts that cause the race by using
the send_IPI_mask() instead of shortcuts when HOTPLUG_CPU is enabled.
In the meantime this patch is the path of lease resistance.
We will switch to bigsmp default sometime soon, when we get to work it again.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For some architectures, a few syscalls are not linked in noMMU mode. In
that case, the MMU depending syscalls are needed to be defined as
'cond_syscall'. For example, ARM architecture selectively links sys_mlock
by the mode configuration.
In case of FRV, it has been managed by #ifdef CONFIG_MMU macro in
arch/frv/kernel/entry.S. However these conditional macros are just
duplicates if they were defined as cond_syscall. Compilation test is done
with FRV toolchains for both of MMU and noMMU mode.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
for sparc64.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch switches arch/i386/mach-voyager/voyager_cat.c to using named
initializers for struct resource.
Besides a fixing compile error in Greg's tree, it makes the code more
readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3473/1: Use numbers 0-15 for the VFP double registers
[ARM] 3472/1: Use the D variants of FLDMIA/FSTMIA on ARMv6
[ARM] 3471/1: FTOSI functions should return 0 for NaN
[ARM] 3470/1: Clear the HWCAP bits for the disabled kernel features
[ARM] 3469/1: S3C24XX: clkout missing hclk selector
[ARM] 3468/1: S3C2410: SMDK common include fix
[ARM] 3461/1: ARM: OMAP: Fix clk_get() when using id and name
[ARM] 3460/1: ARM: OMAP: Remove unnecessary nop_release()
[ARM] 3459/1: ixp23xx: fix debug serial macros for big-endian operation
[ARM] Allow decompressor to be built with -ffunction-sections
[ARM] Fix SA110/SA1100 cache flushing
[ARM] ebsa110: Fix incorrect serial port address
[ARM] Fix ebsa110 debug macros
[ARM] Move FLUSH_BASE macros to asm/arch/memory.h
[ARM] Remove unnecessary extra parens in include/asm-arm/memory.h
[ARM] arm's arch_local_page_offset() fix against 2.6.17-rc1
Patch from Catalin Marinas
This patch changes the double registers numbering to 0-15 from even 0-30,
in preparation for future VFP extensions. It also fixes the VFP_REG_ZERO
bug (value 16 actually represents the 8th double register with the original
numbering).
The original mcrr/mrrc on CP10 were generating FMRRS/FMSRR instead of
FMRRD/FMDRR. The patch changes to CP11 for the correct instructions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The NaN case was dealed with by the "exponent >= ... + 32" condition but it
was not setting the value "d" to 0.
Signed-off-by: Ken'ichi Kuromusha <musha@aplix.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Glibc interprets the HWCAP bits and decides on what features to use.
However, even if the features are present in the hardware, they are not
always supported by the kernel and hence the corresponding bits have to be
cleared from the elf_hwcap variable.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise the build breaks with EXPERIMENTAL disabled
because SPARSEMEM will not get selected properly. See
mm/Kconfig for how that works.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Take doc-book function comment from i386 implementation.
2) cacheline align call_lock, taken from powerpc
3) Need memory barrier after setting call_data
4) Remove timeout
Signed-off-by: David S. Miller <davem@davemloft.net>
GDB uses a PTRACE_PEEKUSR call with offset 0 to see
if a thread is alive, so provide a success return for
this particular special case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Ben Dooks
The clkout0/1 output parent code is missing the
HCLK option, and does not set clk->parent field
after updating the clock field
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
common-smdk.c does not include its own header file
defining the exported prototypes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Recent change to use both id and name when available was
not necessarily returning the right clock as it also searched
for clock name afterwards. This caused MMC to break on H2 and
H3 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Remove unnecessary omap_nop_release() as noted by RMK.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This effectively undoes the PCI resource allocation changes done in
commit b408cbc704, but leaves the cleanups
of that commit in place.
We're going back to marking the resources reported by e820 busy _before_
doing PCI probing, so that any PCI resource that clashes with the BIOS-
reported memory map will be reloacted to a non-clashing area.
The reason? Larry Finger reports that his laptop has the cardbus
controller set up by the BIOS so that it conflicts with the e820 memory
map, and needs to be relocated. See
http://bugzilla.kernel.org/show_bug.cgi?id=6337
for more details.
We'll have to work out how to handle the fbcon problem that caused that
commit in the first place in some other way.
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: <bjk@luxsci.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Or rather compute it based on the table length automatically.
This also has the intended side effect of not warning for new system calls
anymore.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix CONFIG_REORDER.
The value of cflags-y was assined to CFLAGS before cflags-y was assigned
the value used for CONFIG_REORDER.
Use cflags-y for all CFLAGS options in the Makefile to avoid this
happening again.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In linux-2.6.16, we have noticed a problem where the gs base value
returned from an arch_prtcl(ARCH_GET_GS, ...) call will be incorrect if:
- the current/calling task has NOT set its own gs base yet to a
non-zero value,
- some other task that ran on the same processor previously set their
own gs base to a non-zero value.
In this situation, the ARCH_GET_GS code will read and return the
MSR_KERNEL_GS_BASE msr register.
However, since the __switch_to() code does NOT load/zero the
MSR_KERNEL_GS_BASE register when the task that is switched IN has a zero
next->gs value, the caller of arch_prctl(ARCH_GET_GS, ...) will get back
the value of some previous tasks's gs base value instead of 0.
Change the arch_prctl() ARCH_GET_GS code to only read and return
the MSR_KERNEL_GS_BASE msr register if the 'gs' register of the calling
task is non-zero.
Side note: Since in addition to using arch_prctl(ARCH_SET_GS, ...),
a task can also setup a gs base value by using modify_ldt() and write
an index value into 'gs' from user space, the patch below reads
'gs' instead of using thread.gs, since in the modify_ldt() case,
the thread.gs value will be 0, and incorrect value would be returned
(the task->thread.gs value).
When the user has not set its own gs base value and the 'gs'
register is zero, then the MSR_KERNEL_GS_BASE register will not be
read and a value of zero will be returned by reading and returning
'task->thread.gs'.
The first patch shown below is an attempt at implementing this
approach.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the HPET timer is enabled, the clock can drift by ~3 seconds a day.
This is due to the HPET timer not being initialized with the correct
setting (still using PIT count).
If HZ changes, this drift can become even more pronounced.
HPET patch initializes tick_nsec with correct tick_nsec settings for
HPET timer.
Vojtech comments:
"It's not entirely correct (it assumes the HPET ticks totally
exactly), but it's significantly better than assuming the PIT error
there."
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mostly to get better handling when a extended config space
access has to fallback to Type1.
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previously only the first bus would be checked against Type 1.
Why 16? Checking all would need too much memory and we
can assume that systems with more than 16 busses have better than
average quality BIOS.
This is an additional defense against bad MCFG tables.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Intel EM64T CPUs handle uncanonical return addresses differently
from AMD CPUs.
The exception is reported in the SYSRET, not the next instruction.
This leads to the kernel exception handler running on the user stack
with the wrong GS because the kernel didn't expect exceptions
on this instruction.
This version of the patch has the teething problems that plagued an earlier
version fixed.
This is CVE-2006-0744
Thanks to Ernie Petrides and Asit B. Mallick for analysis and initial
patches.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Machine checks can stall the machine for a long time and
it's not good to trigger the nmi watchdog during that.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This prevents crashes on dual core system when enough ticks are lost.
Replaces earlier patch by me.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD systems have a modern APIC that supports 8 bit IDs, but
don't have a XAPIC version number. Add a new "modern_apic"
subfunction that handles this correctly and use it (nearly)
everywhere where XAPIC is tested for.
I removed one wart: the code specified that external APICs
would use an 8bit APIC ID. But I checked a real 82093 data sheet
and it says clearly that they only use 4bit. So I removed
this special case since it would a bit awkward to implement now.
I removed the valid APIC tests in mptable parsing completely. On any modern
system they only check against the full field width (8bit) anyways
and are no-ops. This also fixes them doing the wrong thing
on >8 core Opterons.
This makes i386 boot again on 16 core Opterons.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Needed for other checks later in ACPI.
Pointed out by Len Brown
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When nolapic was passed or the local APIC was disabled
for another reason ACPI would still parse the IO-APICs
until these were explicitely disabled with noapic.
Usually this resulted in a non booting configuration unless
"nolapic noapic" was used.
I also disabled the local APIC parsing in this case, although
that's only cosmetic (suppresses a few printks)
This hopefully makes nolapic work in all cases.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Horus systems don't have anything on bus 0 which makes
the Type 1 sanity checks fail. Use the DMI BIOS year to
check for newer systems and always assume Type 1 works on them.
I used 2001 as an pretty arbitary cutoff year.
Cc: gregkh@suse.de
Cc: Navin Boppuri <navin.boppuri@newisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a user for the e820_all_mapped function:
There have been several machines that don't have a working MMCONFIG,
often because of a buggy MCFG table in the ACPI bios. This patch adds a
simple sanity check that detects a whole bunch of these cases, and when
it detects it, linux now boots rather than crash-and-burns.
The accuracy of this detection can in principle be improved if there was
a "is this entire range in e820 with THIS attribute", but no such
function exist and the complexity needed for this is not really worth
it; this simple check already catches most cases anyway.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a e820_all_mapped() function which checks if the entire range
<start,end> is mapped with type.
This is done by moving the local start variable to the end of each
known-good region; if at the end of the function the start address is
still before end, there must be a part that's not of the correct type;
otherwise it's a good region.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename e820_mapped to e820_any_mapped since it tests if any part of the
range is mapped according to the type.
Later steps will introduce e820_all_mapped which will check if the
entire range is mapped with the type. Both have their merit.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The node setup code would try to allocate the node metadata in the node
itself, but that fails if there is no memory in there.
This can happen with memory hotplug when the hotplug area defines an so
far empty node.
Now use bootmem to try to allocate the mem_map in other nodes.
And if it fails don't panic, but just ignore the node.
To make this work I added a new __alloc_bootmem_nopanic function that
does what its name implies.
TBD should try to use nearby nodes here. Currently we just use any.
It's hard to do it better because bootmem doesn't have proper fallback
lists yet.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Keith Mannthey, Andi Kleen
Implement memory hotadd without sparsemem. The memory in the SRAT
hotadd area is just preserved instead and can be activated later.
There are a few restrictions:
- Only one continuous hotadd area allowed per node
The main problem is dealing with the many buggy SRAT tables
that are out there. The strategy here is to reject anything
suspicious.
Originally from Keith Mannthey, with several hacks and changes by AK
and also contributions from Andrew Morton
[ TBD: Problems pointed out by KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>:
1) Goto's rebuild_zonelist patch will not work if CONFIG_MEMORY_HOTPLUG=n.
Rebuilding zonelist is necessary when the system has just memory <
4G at boot, and hot add memory > 4G. because x86_64 has DMA32,
ZONE_NORAML is not included into zonelist at boot time if system
doesn't have memory >4G at boot.
[AK: should just force the higher zones at boot time when SRAT tells us]
2) zone and node's spanned_pages and present_pages are not incremented.
They should be.
For example, our server (ia64/Fujitsu PrimeQuest) can equip memory
from 4G to 1T(maybe 2T in future), and SRAT will *always* say we have
possible 1T +memory. (Microsoft requires "write all possible memory
in SRAT") When we reserve memmap for possible 1T memory, Linux will
not work well in +minimum 4G configuraion ;)
[AK: needs limiting to 5-10% of max memory]
]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Memory hotadd doesn't need SPARSEMEM, but can be handled by just preallocating
mem_maps. This only needs some untangling of ifdefs to enable the necessary
code even without SPARSEMEM.
Originally from Keith Mannthey, hacked by AK.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just call IRET always, no need for any special cases.
Needed for the next bug fix.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Take a hint from an x86_64 optimization by Arjan van de Ven and use it
for ia64. See a9ba9a3b38
Prefetch the mmap_sem, which is critical for the performance of the page fault
handler.
Note: mm may be NULL but I guess that is safe.
See 458f935527
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The OS INIT handler is loading incorrect values into cr.ifa on exit.
This shows up as a hang when resuming after an INIT that is delivered
while a cpu is in user space. Correct the value loaded into cr.ifa.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The MCA/INIT handlers maintain important state in the SAL to OS (sos)
area and in the monarch_cpu flag. Kernel debuggers (such as KDB) need
this data, and may need to adjust the monarch_cpu field so make the
data available to the notify_die hooks. Define two more events for
calling the functions on the notify_die chain.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We had two implementations for flushing the cache, which meant StrongARM
caches weren't being correctly flushed. Fix this by always using the
v4wb_flush_kern_cache_all method, rather than duplicating it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FLUSH_BASE must be visible to arch/arm/mm/init.c in order for the
memory region to be setup. Move these definitions from
asm-arm/arch-*/hardware.h into asm-arm/arch-*/memory.h where mm
stuff can see them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu under
arch/ia64/kernel/.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fjitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Get rid of the manual search of _CRS, in favor of
acpi_get_vendor_resource() which is now provided by the ACPI CA. And fall
back to searching for a consumer-only address space descriptor if no
vendor-defined resource is found.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The patch removing _machine and converting platforms over to use
define_machine wasn't complete as far as CHRP was concerned. This
adds the define_machine call for CHRP and gets it booting again.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using a relative path has the advantage that when the kernel source
tree is moved the relevant .o files will not be rebuild just because
the path to the kernel src has changed.
This also got rid of a user of TOPDIR - which has been deprecated for a long time now.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The iSeries Hypervisor only allows us to specify IRQ numbers up to 255 (it
has a u8 field to pass it in). This patch allows platforms to specify a
maximum to the virtual IRQ numbers we will use and has iSeries set that
to 255. If not set, the maximum is NR_IRQS - 1 (as before).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Wire up sys_sync_file_range() into syscall tables.
[SPARC]: Wire up sys_splice() into the syscall tables.
[SPARC64]: Update defconfig.
[SPARC64]: Align address in huge_pte_alloc().
[SPARC64]: Document the instruction checks we do in do_sparc64_fault().
[SPARC64]: Make tsb_sync() mm comparison more precise.
Patch from Pavel Pisa
This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.
There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.
Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(We'd only added the number, which meant that actually trying
to use splice just went off into la-la-land)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update misc OMAP core code from linux-omap tree:
- McBSP updates by Samuel Ortiz, Andrzej Zaborowski
- Whitespace cleanups by Ladislav Michl
- Other fixes by various linux-omap developers
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP framebuffer low-level init code from linux-omap tree
by Imre Deak.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP PM code from linux-omap tree:
- Move PM code from plat-omap to mach-omap1 and mach-omap2
by Tony Lindgren
- Add minimal PM support for omap24xx by Tony Lindgren and
Richard Woodruff
- Misc updates to omap1 PM code by Tuukka Tikkanen et al
- Updates to the SRAM code needed for PM and FB by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP GPIO code from linux-omap tree:
- Fix omap16xx edge control by Juha Yrjola
- Support for additional omap16xx trigger modes by Dirk Behme
- Fix edge detection by Tony Lindgren et al.
- Better support for omap15xx and omap310 by Andrej Zaborowski
- Fix omap15xx interrupt bug by Petukhov Nikolay
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP pin multiplexing code from linux-omap tree.
This patch adds new pin configurations by various OMAP
developers, and suport for omap730 by Brian Swetland.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP timers from linux-omap tree. The highlights of the
patch are:
- Move timer32k code from mach-omap1 to plat-omap and make it
work also on omap24xx by Tony Lindgren
- Add support for dmtimer idle check for PM by Tuukka Tikkanen
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP clock framework from linux-omap tree.
The highlights of the patch are:
- Add support for omap730 clocks by Andrzej Zaborowski
- Fix compile warnings by Dirk Behme
- Add support for using dev id by Tony Lindgren and Komal Shah
- Move memory timings and PRCM into separate files by Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the platform device resources for the Ethernet and
MMC peripherals. It also adds platform device information for the NAND
(SmartMedia), I2C and the RTC.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
On the Atmel AT91RM9200-DK and -EK boards, a pin is used to control
whether the card socket is used for a DataFlash Card or an MMC/SD card.
We now default to MMC/SD in the configuration files.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support for the LED(s) on the AT91RM9200-based boards.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Force the Sharp Zaurus Poodle memory size to 32MB.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
From: Stefano Fedrigo <aleph@develer.com>
This adds to the MX1ADS platform the needed code to detect
insertion/removal of an MMC/SD card. Tested on a v1.1 board.
Signed-off-by: Stefano Fedrigo <aleph@develer.com>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
This patch contains simplified set of changes to add scatter-gather
emulation capability into MX1 DMA support. The result should
be still usable for next combination of DMA transfers
Statter-Gather/linear/2D/FIFO to linear/2D/FIFO and
linear/2D/FIFO to Statter-Gather/2D/FIFO
The patch corrects channel priority allocation to be compatible
with MX1 hardware implementation.
Previous code has not been adapted from its PXA original.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Instantiate the recently merged m48t86 rtc driver in the ts72xx code.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Instantiate the recently merged ep93xx rtc driver in the ep93xx code.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
NAND definitions for the HP iPAQ RX3715's
internal NAND flash
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The NAND timings on the Anubis are too large
to be selected when running at 133MHz memory
clock.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the bug in the UPLL enable code which should
have put a 200uS delay in if enabling the USB PLL
from the state where it is off.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add SMDK2410/SMDK2440 NAND device information
and default partition table.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Set default state of LEDs to off
Fixes context of Patch #3442/1
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the powerpc 64k pages patch went in, systems that have SLBs
(like Power4 iSeries) needed to have slb_initialize called to set up
some variables for the SLB miss handler. This was not being called
on the boot processor on iSeries, so on single cpu iSeries machines,
we would get apparent memory curruption as soon as we entered user mode.
This patch fixes that by calling slb_initialize on the boot cpu if the
processor has an SLB.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Lennert Buytenhek
This patch adds support for the I/O coherent cache available on the
xsc3. The approach is to provide a simple API to determine whether the
chipset supports coherency by calling arch_is_coherent() and then
setting the appropriate system memory PTE and PMD bits. In addition,
we call this API on dma_alloc_coherent() and dma_map_single() calls.
A generic version exists that will compile out all the coherency-related
code that is not needed on the majority of ARM systems.
Note that we do not check for coherency in the dma_alloc_writecombine()
function as that still requires a special PTE setting. We also don't
touch dma_mmap_coherent() as that is a special ARM-only API that is by
definition only used on non-coherent system.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The SMDK2410 and SMDK2440 boards have a number of items
in common, including the LEDs, Ethernet, PCMCIA. Make
a common SMDK support file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the Double Espresso board, the IXP2350s are PCI slave devices and
we skip calling pci_common_init() as that enumerates the bus. But even
though we are a PCI slave device, there is still some PCI-related setup
that has to be done.
Create ixp23xx_pci_common_init(), move the common initialisation bits
there, and have this function called from both the PCI master and the
PCI slave init path.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Missing include for __NR_syscalls, and missing sys_splice() that
causes build-time failure due to compile-time bounds check on
spu_syscall_table.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes unnecessary exports, marks functions as static when
possible, and simplifies some list-related code.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes several problems with the lparcfg code. In case
someone gets a sense of deja-vu, part of this was submitted last Sep, I
thought the changes went in, but either got backed out, or just got
lost.
First, change the local_buffer declaration to be unsigned char *. We
had a bad-math problem in a 2.4 tree which was built with a
"-fsigned-char" parm. I dont believe we ever build with that parm
now-a-days, but to be safe, I'd prefer the declaration be explicit.
Second, fix a bad math calculation for splpar_strlen.
Third, on the rtas_call for get-system-parameter, pass in
RTAS_DATA_BUF_SIZE for the rtas_data_buf size, instead of letting random
data determine the size. Until recently, we've had a sufficiently
large 'random data' value get passed in, so the function just happens to
have worked OK. Now it's getting passed a '0', which causes the
rtas_call to return success, but no data shows up in the buffer.
(oops!). This was found by the LTC test org.
This is in a branch of code that only gets run on SPLPAR systems.
Tested on power5 Lpar.
Signed-off-by: Will Schmidt <willschm@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent patch to print device names in EEH reset messages
was lacking ... this patch works better.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This extends the HCALL interface for InfiniBand usage. I've
made the patch against the linux-2.6 git tree and Segher's patch:
[PATCH] Change H_StudlyCaps to H_SHOUTING_CAPS
We moved this into the common powerpc code based on comments we
got after posting the first eHCA InfiniBand device driver patch.
Signed-off-by: Heiko j Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also cleans up some nearby whitespace problems.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current code prints an ambiguous message if the recovery
of a failed PCI device fails. Give this special case its own
unique message.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This forces the processing of EEH PCI events to be serialized,
using a very simple mutex lock. This serialization is required to
avoid races involving additional PCI device failures that may occur
during the recovery phase of a previous failure.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Pavel Machek
> The kautobuild found the following error while trying to build 2.6.16-git18
> using collie_defconfig:
>
> arch/arm/mach-sa1100/collie.c:92: error: 'collie_uart_set_mctrl' undeclared here (not in a function)
> arch/arm/mach-sa1100/collie.c:93: error: 'collie_uart_get_mctrl' undeclared here (not in a function)
> make[1]: *** [arch/arm/mach-sa1100/collie.o] Error 1
> make: *** [arch/arm/mach-sa1100] Error 2
> make: Leaving directory `/var/tmp/kernel-orig'
This fixes above compile error by adding missing pieces of uart
support, and fixes compilation.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Komal Shah
This patch fixes the duplicate exports of string library functions.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are about to fill in all HPAGE_SIZE's worth
of PAGE_SIZE ptes, so we have to give the first
pte in that set else we scribble over random memory
when we fill in the ptes.
Signed-off-by: David S. Miller <davem@davemloft.net>
switch_mm() changes the mm state and does a tsb_context_switch()
first, then we do the cpu register state switch which changes
current_thread_info() and current().
So it's safer to check the PGD physical address stored in the
trap block (which will be updated by the tsb_context_switch() in
switch_mm()) than current->active_mm.
Technically we should never run here in between those two
updates, because interrupts are disabled during the entire
context switch operation. But some day we might like to leave
interrupts enabled during the context switch and this change
allows that to happen without any surprises.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3424/2: ixp23xx: fix uncompress.h for recent CRLF decompressor change
[ARM] 3434/1: pxa i2s amsl define
[ARM] 3425/1: xsc3: need to include pgtable-hwdef.h
[ARM] Allow un-muxed syscalls to be available for everyone
[ARM] 3420/1: Missing clobber in example code
[ARM] nommu: fixups for the exception vectors
[ARM] nommu: add nommu specific Kconfig and MMUEXT variable in Makefile
[ARM] nommu: start-up code
[ARM] nommu: MPU support in boot/compressed/head.S
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Avoid "u64 foo : 32;" for gcc3 vs. gcc4 compatibility
[IA64] Export cpu cache info by sysfs
The only user of get_wchan is the proc fs - and proc can't be built modular.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generalise the Corgi backlight driver by moving the default intensity and
limit mask settings into the platform specific data structure. This enables
the driver to support other Zaurus hardware, specifically the SL-6000x (Tosa)
model.
Also change the spinlock to a mutex (the spinlock is overkill).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds LED drivers for LEDs found on the Sharp Zaurus c6000 model (tosa).
Signed-off-by: Dirk Opfer <dirk@opfer-online.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds LED drivers for LEDs found on the Sharp Zaurus c7x0 (corgi, shepherd,
husky) and cxx00 (akita, spitz, borzoi) models.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an LED trigger for the charger status as found on the Sharp Zaurus series
of devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the foundations of a new LEDs subsystem. This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the recently-added LINUX_FADV_ASYNC_WRITE and LINUX_FADV_WRITE_WAIT
fadvise() additions, do it in a new sys_sync_file_range() syscall instead.
Reasons:
- It's more flexible. Things which would require two or three syscalls with
fadvise() can be done in a single syscall.
- Using fadvise() in this manner is something not covered by POSIX.
The patch wires up the syscall for x86.
The sycall is implemented in the new fs/sync.c. The intention is that we can
move sys_fsync(), sys_fdatasync() and perhaps sys_sync() into there later.
Documentation for the syscall is in fs/sync.c.
A test app (sync_file_range.c) is in
http://www.zip.com.au/~akpm/linux/patches/stuff/ext3-tools.tar.gz.
The available-to-GPL-modules do_sync_file_range() is for knfsd: "A COMMIT can
say NFS_DATA_SYNC or NFS_FILE_SYNC. I can skip the ->fsync call for
NFS_DATA_SYNC which is hopefully the more common."
Note: the `async' writeout mode SYNC_FILE_RANGE_WRITE will turn synchronous if
the queue is congested. This is trivial to fix: add a new flag bit, set
wbc->nonblocking. But I'm not sure that we want to expose implementation
details down to that level.
Note: it's notable that we can sync an fd which wasn't opened for writing.
Same with fsync() and fdatasync()).
Note: the code takes some care to handle attempts to sync file contents
outside the 16TB offset on 32-bit machines. It makes such attempts appear to
succeed, for best 32-bit/64-bit compatibility. Perhaps it should make such
requests fail...
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark unwind info for signal trampolines using the new S augmentation flag
introduced in: http://gcc.gnu.org/PR26208.
GCC 4.2 (or patched earlier GCC) will be able to special case unwinding
through frames right above signal trampolines. As the augmentations start
with z flag and S is at the very end of the augmentation string, older GCCs
will just skip the S flag as unknown (that's why an augmentation flag was
chosen over say a new CFA opcode).
Signed-off-by: Jakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If running on a host not supporting TLS (for instance 2.4) we should report
that cleanly to the user, instead of printing not comprehensible "error 5" for
that.
Additionally, i386 and x86_64 support different ranges for
user_desc->entry_number, and we must account for that; we couldn't pass
ourselves -1 because we need to override previously existing TLS descriptors
which glibc has possibly set, so test at startup the range to use.
x86 and x86_64 existing ranges are hardcoded.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Newly forked threads have no arch_switch_to_skas() called before their first
run, because when schedule() switches to them they're resumed in the body of
thread_wait() inside fork_handler() rather than in switch_threads() in
switch_to_skas(). Compensate this missing call.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Copy the definition of struct user_desc (with another name) for use by
userspace sources (where we use the host headers, and we can't be sure about
their content) to make sure UML compiles.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement sys_[gs]et_thread_area and the corresponding ptrace operations for
UML. This is the main chunk, additional parts follow. This implementation is
now well tested and has run reliably for some time, and we've understood all
the previously existing problems.
Their implementation saves the new GDT content and then forwards the call to
the host when appropriate, i.e. immediately when the target process is
running or on context switch otherwise (i.e. on fork and on ptrace() calls).
In SKAS mode, we must switch registers on each context switch (because SKAS
does not switches tls_array together with current->mm).
Also, added get_cpu() locking; this has been done for SKAS mode, since TT does
not need it (it does not use smp_processor_id()).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call arch_switch also in switch_to_skas, even if it's, for now, a no-op for
that case (and mark this in the comment); this will change soon.
Also, arch_switch for TT mode is actually useless when the PT proxy (a
complicate debugging instrumentation for TT mode) is not enabled. In fact, it
only calls update_debugregs, which checks debugregs_seq against seq (to check
if the registers are up-to-date - seq here means a "version number" of the
registers).
If the ptrace proxy is not enabled, debugregs_seq always stays 0 and
update_debugregs will be a no-op. So, optimize this out (the compiler can't
do it).
Also, I've been disappointed by the fact that it would make a lot of sense if,
after calling a successful
update_debugregs(current->thread.arch.debugregs_seq),
current->thread.arch.debugregs_seq were updated with the new debugregs_seq.
But this is not done. Is this a bug or a feature? For all purposes, it seems
a bug (otherwise the whole mechanism does not make sense, which is also a
possibility to check), which causes some performance only problems (not
correctness), since we write_debugregs when not needed.
Also, as suggested by Jeff, remove a redundant enabling of SIGVTALRM,
comprised in the subsequent local_irq_enable(). I'm just a bit dubious if
ordering matters there...
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ldt-{i386,x86_64}.h is made of two different parts - some code for parsing of
LDT descriptors, which is arch-dependant, and the code to handle uml_ldt_t (an
LDT block inside UML), which is mostly arch-independant (among x86 and x86_64,
at least).
Join the common part in a single file (ldt.h) and split the rest away
(host_ldt-{i386,x86_64}.h).
This is needed because processor.h, with next patches, will start including
the LDT descriptor parsing macros in host_ldt.h, but it can't include ldt.h
because it uses semaphores (and to define semaphores one must first include
processor.h!).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Comparing this code which is the actual body of the arch-independent
cpu_idle(), it is clear that it's unnecessary to set ->mm and ->active_mm;
beyond that, a kernel thread is not supposed to have ->mm != NULL, only
active_mm.
This showed up because I used the assumption (which is IMHO valid) that kernel
thread have their ->mm == NULL, and it failed for this thread.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
type-safe min() in arch/um/drivers/mconsole_kern.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed assignments to unused variables in arch/um/os-Linux/Makefile
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
misc sparse annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kconfig sanitized around drivers/net
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
no need to add the same file twice to MRPROPER_FILES
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kills unmap magic
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kills symlinks in arch/um/sys-*
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A number of UML initcalls were improperly returning 1. Also removed any
nearby emacs formatting comments.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The earlier printf patch missed a corresponding change in the printed
variable.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes since first version
added check for MADV_REMOVE support on the host
fixed error return botch
shrunk sprintf array by one character
This adds hotplug memory support to UML. The mconsole syntax is
config mem=[+-]n[KMG]
In other words, add or subtract some number of kilobytes, megabytes, or
gigabytes.
Unplugged pages are allocated and then madvise(MADV_TRUNCATE), which is a
currently experimental madvise extension. These pages are tracked so they
can be plugged back in later if the admin decides to give them back. The
first page to be unplugged is used to keep track of about 4M of other
pages. A list_head is the first thing on this page. The rest is filled
with addresses of other unplugged pages. This first page is not madvised,
obviously.
When this page is filled, the next page is used in a similar way and linked
onto a list with the first page. Etc. This whole process reverses when
pages are plugged back in. When a tracking page no longer tracks any
unplugged pages, then it is next in line for plugging, which is done by
freeing pages back to the kernel.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Porting the patch I posted for x86_64 to i386.
http://marc.theaimsgroup.com/?l=linux-kernel&m=114178139610707&w=2
o While using kdump, after a system crash when second kernel boots, timer
vector gets (0x31) locked and CPU does not see timer interrupts
travelling from IOAPIC to APIC. Currently it does not lead to boot
failure in second kernel as timer interrupts continues to come as ExtInt
through LAPIC directly, but fixing it is good in case some boards do not
support the other mode.
o After a system crash, it is not safe to service interrupts any more,
hence interrupts are disabled. This leads to pending interrupts at
LAPIC. LAPIC sends these interrupts to the CPU during early boot of
second kernel. Other pending interrupts are discarded saying unexpected
trap but timer interrupt is serviced and CPU does not issue an LAPIC EOI
because it think this interrupt came from i8259 and sends ack to 8259.
This leads to vector 0x31 locking as LAPIC does not clear respective ISR
and keeps on waiting for EOI.
o This patch issues extra EOI for the pending interrupts who have ISR set.
o Though today only timer seems to be the special case because in early
boot it thinks interrupts are coming from i8259 and uses
mask_and_ack_8259A() as ack handler and does not issue LAPIC EOI. But
probably doing it in generic manner for all vectors makes sense.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
