Looks like a local change I made to be able to test-compile the i2c-pasemi
driver leaked upstream.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users have been complaining about the w83627ehf driver flooding their logs
with debug messages like:
w83627ehf 9191-0a10: Increasing fan 4 clock divider from 64 to 128
or:
w83627ehf 9191-0290: Increasing fan 4 clock divider from 4 to 8
The reason is that we failed to actually write the LSB of the encoded clock
divider value for that fan, causing the next read to report the same old value
again and again.
Additionally, the fan number was improperly reported, making the bug harder to
find.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It got its lock and unlock backwards.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=8334
(obviously, this code could be using plain old spin_lock_irq(), too)
Cc: <matthias.kaehlcke@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that the last patch to change set_cs to be kept in the
controller's structure instead of the platform data was an incomplete
change, and did not change the references to platfrom data in the setup
xfer code. (This can prevent an oops.)
Reported-by: <Ling.Alex@iac.com.tw>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While digging through my MAP_FIXED changes, I found that rather obvious
bug in /dev/mem mmap implementation for nommu archs. get_unmapped_area()
is expected to return an address, not a pfn.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-By: David Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In mthca_arbel_fmr_unmap(), the high bits of the key are masked off.
This gets rid of the effect of adjust_key(), which makes sure that
bits 3 and 23 of the key are equal when the Sinai throughput
optimization is enabled, and so it may happen that an FMR will end up
with bits 3 and 23 in the key being different. This causes data
corruption, because when enabling the throughput optimization, the
driver promises the HCA firmware that bits 3 and 23 of all memory keys
will always be equal.
Fix by re-applying adjust_key() after masking the key.
Thanks to Or Gerlitz for reproducing the problem, and Ariel Shahar for
help in debug.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We only map DMA when cmd->request_bufflen is non-zero for non-sg
buffers, we thus should make the same check when unmapping.
Based upon a report from Pasi Pirhonen.
Signed-off-by: David S. Miller <davem@davemloft.net>
3w-xxxx emulates a REQUEST_SENSE response by simply returning nothing.
Unfortunately, it's assuming that the REQUEST_SENSE command is
implemented with use_sg == 0, which is no longer the case. The oops
occurs because it's clearing the scatterlist in request_buffer instead
of the memory region.
This is fixed by using tw_transfer_internal() to transfer correctly to
the scatterlist.
Acked-by: adam radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
DVB USB remotes do not support changing keycode maps but set
input_dev->keycodesize and input_dev->keycodemax without setting
input_dev->keycode. This causes kernel oops when user tries to
look up (or change) current keymap.
While the proper fix would be to make remotes handle keymap changes
we'll just remove keycodemax and keycodesize initialization so
EVIOCGKEYCODE and EVIOCSKEYCODE will simply return -EINVAL.
http://bugzilla.kernel.org/show_bug.cgi?id=8312
Signed-off-by: olaf.kirch@oracle.com
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If 'num_pages' were ever 1 more than a multiple of 8 (32bit platforms)
or of 16 (64 bit platforms). filemap_attr would be allocated one
'unsigned long' shorter than required. We need a round-up in there.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of commit 6cdbd77e ("cxgb3 - missing CPL hanler and register
setting."), the cxgb3 ethernet NIC driver no longer handles SET_TCB
replies, so we need to do it in the iWARP driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
myri10ge: update driver version to 1.3.0-1.233
myri10ge: more Intel chipsets providing aligned PCIe completions
myri10ge: fix management of the firmware 4KB boundary crossing restriction
cxgb3 - missing CPL hanler and register setting.
cxgb3 - MAC watchdog update
cxgb3 - avoid deadlock with mac watchdog
skge: fix wake on lan
sky2: phy workarounds for Yukon EC-U A1
sky2: turn on clocks when doing resume
sky2: turn carrier off when down
skge: turn carrier off when down
[PATCH] bcm43xx: Fix PPC machine checks and match loopback gain specs
[PATCH] bcm43xx: Fix 802.11b/g scan limits to match regulatory reqs
[PATCH] zd1211rw: Fix E2P_PHY_REG patching
[PATCH] zd1211rw: Reject AL2230S devices
Noone should use kobj.name directly since it may contain garbage.
Objects with longer names have them stored in separately allocated
memory pointed to by kobj->k_name.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the Nikon D80 camera will not work without an UNUSUAL_DEV entry embodied
in the attached patch (made against 2.6.20.3). Hope you find it helpful,
or if not, pass it along to someone who does.
From: Emil Larsson <emil@swip.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is one significant difference between the behavior of root hubs
(as embodied in host controller hardware) and external hubs: When a
remote-wakeup signal is received, an external hub sends an interrupt
message at the _end_ of the resume sequence but a root hub generates
and interrupt at the _beginning_ of the resume sequence. The host
system must poll for the end of the sequence.
When ehci-hcd was converted to interrupt-driven operation instead of
using polling, the remaining need for this particular poll was
overlooked. This patch (as894) fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the Intel 5000 southbridge (aka Intel 6310/6311/6321ESB) PCIe ports
and the Intel E30x0 chipsets to the whitelist of aligned PCIe completion.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simpler way of dealing with the firmware 4KB boundary crossing
restriction for rx buffers. This fixes a variety of memory
corruption issues when using an "uncommon" MTU with a 16KB
page size.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove specific CPL handler.
Add missing CPL handler.
Add missing register setting when the interface is brought up.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The MAC watchdog was failing if the peer interface was brought down.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a deadlock when the interface s configured down and
the watchdog tack is sleeping on rtnl_lock.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to rework wake on lan code to setup properly and get activated
on shutdown (and suspend), not when ethtool is run.
This does not need to go to stable queue because wake on lan
was not even included in 2.6.20 (or earlier versions).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround Yukon EC-U wasn't comparing with correct
version and wasn't doing correct setup. Without it, 88e8056
throws all sorts of errors.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some of these chips are disabled until clock is enabled.
This fixes:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404107
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down, otherwise it can
confuse bonding and bridging and looks like carrier is on immediately
when it is brought back up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The UCB1400 is missing a name parameter in the device_driver struct.
This causes missing information in the /sys tree and seems to cause
other problems with the AC97 functionality. This was tested on a PXA270
system.
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: add "optical" to sysfs "media" attribute
ide: ugly messages trying to open CD drive with no media present
ide: correctly prevent IDE timer expiry function to run if request was already handled
Add "optical" to sysfs "media" attribute as already in /proc
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I get the following error messages when trying to open a CD device
(specifically, the Teac CD-ROM CD-224E) that has no media present:
hda: packet command error: status=3D0x51 { DriveReady SeekComplete Error }
hda: packet command error: error=3D0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
This happens when a "start stop unit" command (0x1b 0 0 0 3 0 0 0 0 0)
is sent to the drive to try to close the CD-ROM tray, but this drive
doesn't have that capability (it's a slim portable-type CD-ROM), so it
reports sense key 5 (illegal request) with asc/ascq 24/0. This is
exactly how SFF8090i says it should respond.
But ide-cd.c (in cdrom_decode_status() ) just sees sense key 5 and spews
out an error. It then goes on to request sense data, and
cdrom_log_sense() understands this error and doesn't log it.
The patch, for kernel 2.6.20.4, suppresses this error message.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The specifications for loopback_gain calculation and for G PHY
initialization have been updated. This patch implements them and
fixes a machine check error that occurs for PPC architecture with a
phy->rev of 1.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 802.11b/g mode, bcm43xx actively scans channels 1-14 no matter what
locale has been set, either in the sprom or by the locale option. This
behaviorviolates regulatory rules everywhere in the world except
Japan. This patch changes the default range to the correct value if the
locale has been set, and to channels 1-13 if no locale has been set.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to conflicting/confusing defines in the vendor driver, we were
reading E2P_PHY_REG from the wrong location.
CR157 patching was slightly incorrect in that the vendor driver only
patches in an 8-bit value, whereas we were patching 24 bits.
Additionally, CR157 patching was happening on both zd1211 and zd1211b,
but this should only happen on zd1211.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Receive buffers need to be mapped with DMA_FROM_DEVICE. Incorrectly
mapping with DMA_TO_DEVICE causes a hard lock on ppc64 machines with
an IOMMU.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=431>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
zd1211rw currently detects AL2230S-based devices as AL2230, and hence
programs the RF incorrectly. Transmit silently fails on this
misconfiguration.
After this patch, AL2230S devices are rejected with an error message, to
avoid any confusion with an apparent driver bug.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On G965, I810_PGETBL_CTL is a mmio offset, but we wrongly take it
as pci config space offset in detecting GTT size. This one line patch
fixs this.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The spin_lock calls made in dev->open and dev->close must disable
BH since open/close are made in process context. Conversely, the
call in dev->hard_start_xmit does not need to disable BH since it
is already executing with BH disabled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nobody ported ffmpeg from dv1394 to rawiso yet, and there is no
justification to remove dv1394 right now.
Nevertheless, a strong deprecation of this ABI makes a lot of sense,
especially as Kristian H's drivers shape up to be an attractive
alternative to the existing ones. But we don't have a schedule at the
moment.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Convert omap_cf into a platform_driver ... this resolves oopsing during
suspend/resume.
Evidently folk haven't tried suspend/resume on an OSK (the main platform
for this driver) since September or so, which is when platform_device
learned about suspend_late()/resume_early() and stopped being able to
suspend/resume without a platform_driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver will crash when the chip has been initialized by EFI before
tg3_init_one(). In this case, the driver will call tg3_chip_reset()
before allocating consistent memory.
The bug is fixed by checking for tp->hw_status before accessing it
during tg3_chip_reset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a connection is terminated asynchronously from the iSCSI layer's
perspective, iSER needs to notify the iSCSI layer that the connection
has failed. This is done using a workqueue (switched to from the iSER
tasklet context). Meanwhile, the connection object (that holds the
work struct) is released. If the workqueue function wasn't called
yet, it will be called later with a NULL pointer, which will crash the
kernel.
The context switch (tasklet to workqueue) is not required, and
everything can be done from the iSER tasklet. This eliminates the NULL
work struct bug (and simplifies the code).
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Truncated reports should not be discarded since it prevents buggy
devices from communicating with userspace.
Prior to the regession introduced in 2.6.20, a shorter-than-expected
report in hid_input_report() was passed thru after having the missing
bytes cleared. This behavior was established over a few patches in the
2.6.early-teens days, including commit
cd6104572b.
This patch restores the previous behavior and fixes the regression.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
drivers/tc/zs.c:73:24: error: asm/dec/tc.h: No such file or directory
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds initialization of drv->cylinders back into the failing case in
cciss_geometry_inquiry. I inadvertently removed it in one my 2TB updates.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert all this. It can cause device-mapper to receive a different major from
earlier kernels and it turns out that the Amanda backup program (via GNU tar,
apparently) checks major numbers on files when performing incremental backups.
Which is a bit broken of Amanda (or tar), but this feature isn't important
enough to justify the churn.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A device can be removed from an md array via e.g.
echo remove > /sys/block/md3/md/dev-sde/state
This will try to remove the 'dev-sde' subtree which will deadlock
since
commit e7b0d26a86
With this patch we run the kobject_del via schedule_work so as to
avoid the deadlock.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] cio: Fix handling of interrupt for csch().
[S390] page_mkclean data corruption.
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Limit ATAPI DMA to R/W commands only for TORiSAN DVD drives (take 3)
libata: Limit max sector to 128 for TORiSAN DVD drives (take 3)
libata: Clear tf before doing request sense (take 3)
libata: reorder HSM_ST_FIRST for easier decoding (take 3)
libata bugfix: preserve LBA bit for HDIO_DRIVE_TASK
2.6.21 fix lba48 bug in libata fill_result_tf()
This adds some NCQ blacklist entries taken from the Silicon Image 3124/3132
Windows driver .inf files. There are some confirming reports of problems
with these drives under Linux (for example http://lkml.org/lkml/2007/3/4/178)
so let's disable NCQ on these drives.
[ I'm personally starting to wonder whether we shouldn't disable NCQ by
default, and perhaps have a white-list. There seems to be a *lot* of
drives that do this wrong.. - Linus ]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
r8169: fix suspend/resume for down interface
r8169: issue request_irq after the private data are completely initialized
b44: fix IFF_ALLMULTI handling of CAM slots
cxgb3 - Firwmare update
cxgb3 - Tighten xgmac workaround
cxgb3 - detect NIC only adapters
cxgb3 - Safeguard TCAM size usage
Wipe internal irb if the clear function bit is set before accumulating
bits from the irb in order to follow hardware behaviour.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
patch 4/4:
Limit ATAPI DMA to R/W commands only for TORiSAN DRD-N216 DVD-ROM drives
(http://bugzilla.kernel.org/show_bug.cgi?id=6710)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
patch 3/4:
The TORiSAN drive locks up when max sector == 256.
Limit max sector to 128 for the TORiSAN DRD-N216 drives.
(http://bugzilla.kernel.org/show_bug.cgi?id=6710)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
patch 2/4:
Clear tf before doing request sense.
This fixes the AOpen 56X/AKH timeout problem.
(http://bugzilla.kernel.org/show_bug.cgi?id=8244)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Preserve the LBA bit in the DevSel/Head register for HDIO_DRIVE_TASK.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current 2.6.21 libata does the following:
void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
tf->command = ata_check_status(ap);
...
if (tf->flags & ATA_TFLAG_LBA48) {
iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr);
tf->hob_feature = ioread8(ioaddr->error_addr);
...
}
}
...
static void fill_result_tf(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
ap->ops->tf_read(ap, &qc->result_tf);
qc->result_tf.flags = qc->tf.flags;
}
Based on this, those last two statements fill_result_tf()
appear to me to be in the wrong order, in that the tf->flags
are uninitialized at the point where tf_read() is invoked.
So for lba48 commands, tf_read() won't be reading back the
full lba48 register contents..
Correct?
This patch corrects fill_result_tf() so that the flags
get copied to result_tf before they are used by tf_read().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you set the IFF_ALLMULTI flag on a b44 device, or if you join more than
B44_MCAST_TABLE_SIZE multicast groups, the device will stop receiving unicast
messages. This is because the __b44_set_mac_addr call sets the zeroth CAM
entry to the MAC address of the device, and then the loop at line 1722
proceeds to overwrite it unless the value of i is set by the __b44_load_mcast
call. However, when IFF_ALLMULTI is set, that call is bypassed, leaving i set
to zero.
Fixed by starting the loop at 1 to make it skip the CAM entry for the MAC
address.
Signed-off-by: Bill Helfinstine <bhelf@flitterfly.whirpon.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Run the watchdog task when the link is up.
Flush the XGMAC Tx FIFO when the link drops.
Also remove a statistics update that should have gone
in the previous modification of xgmac.c.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Differentiate NIC only adapters from RNICs.
Initialize offload capabilities for RNICs only.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a simplified and actually more comprehensive form of a bug
fix from Mitch Williams <mitch.a.williams@intel.com>.
When we mask or unmask a msi-x irqs the writes may be posted because
we are writing to memory mapped region. This means the mask and
unmask don't happen immediately but at some unspecified time in the
future. Which is out of sync with how the mask/unmask logic work
for ioapic irqs.
The practical result is that we get very subtle and hard to track down
irq migration bugs.
This patch performs a read flush after writes to the MSI-X table for mask
and unmask operations. Since the SMP affinity is set while the interrupt
is masked, and since it's unmasked immediately after, no additional flushes
are required in the various affinity setting routines.
The testing by Mitch Williams on his especially problematic system should
still be valid as I have only simplified the code, not changed the
functionality.
We currently have 7 drivers: cciss, mthca, cxgb3, forceth, s2io,
pcie/portdrv_core, and qla2xxx in 2.6.21 that are affected by this
problem when the hardware they driver is plugged into the right slot.
Given the difficulty of reproducing this bug and tracing it down to
anything that even remotely resembles a cause, even if people are
being affected we aren't likely to see many meaningful bug reports, and
the people who see this bug aren't likely to be able to reproduce this
bug in a timely fashion. So it is best to get this problem fixed
as soon as we can so people don't have problems.
Then if people do have a kernel message stating "No irq for vector" we
will know it is yet another novel cause that needs a complete new
investigation.
Cc: Greg KH <greg@kroah.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SCSI]: Fix scsi_send_eh_cmnd scatterlist handling
[SPARC]: Add unsigned to unused bit field in a.out.h
This fixes a regression caused by commit:
2dc611de5a
The sense buffer code in scsi_send_eh_cmnd was changed to use
alloc_page() and a scatter list, but the sense data copy was not
updated to match so what we actually get in the sense buffer is total
grabage starting with the kernel address of the struct page we got.
Basically the stack frame of scsi_send_eh_cmd() is what ends up
in the sense buffer.
Depending upon how pointers look on a given platform, you can
end up getting sr_ioctl.c errors when you mount a cdrom. If
the CDROM gives a check condition for GPCMD_GET_CONFIGURATION issued
by drivers/cdrom/cdrom.c:cdrom_mmc_profile(), sr_ioctl will
spit out this error message in sr_do_ioctl() with the way pointers
are on sparc64:
default:
printk(KERN_ERR "%s: CDROM (ioctl) error, command: ", cd->cdi.name);
__scsi_print_command(cgc->cmd);
scsi_print_sense_hdr("sr", &sshdr);
err = -EIO;
This is the error Tom Callaway reported in:
http://marc.info/?l=linux-sparc&m=117407453208101&w=2
Anyways, fix this by using page_address(sgl.page) which is OK
because we know this is low-mem due to GFP_ATOMIC.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Christoph Hellwig <hch@lst.de>
The nvram dword alignment logic was broken when writing less than 4
bytes on a non-aligned offset. It was missing logic to round the
length to 4 bytes.
The page erase code is also moved so that it is only called when
using non-buffered flash for better code clarity.
Update version to 1.5.7.
Based on initial patch from Tony Cureington <tony.cureington@hp.com>.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a multiprocessor machine the VT_WAITACTIVE ioctl call may return 0 if
fg_console has already been updated in redraw_screen() but the console
switch itself hasn't been completed. Fix this by checking fg_console in
vt_waitactive() with the console sem held.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lockdep reported cmos_suspend() and cmos_resume() calling rtc_update_irq()
with IRQs enabled; not allowed.
Also fix problems seen on some hardware, whereby false alarm IRQs could be
reported (primarily to userspace); and update two comments to match changes
in ACPI. Those make up most of this patch, by volume.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change PnP resource handling code to use proper type for resource start and
length. Fixes bogus regions reported in /proc/iomem.
I've also made some pointer constant, as they are constant...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an off-by-one spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ADEF bits in the TSCR register have different meanings in read and
write mode. For this reason ADEF has to be reset on every
read-modify-write operation.
This patch introduces a special write function for this register, which
takes care of it.
Thanks to Holger Magnussen for pointing my nose at this problem.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Setting the message length to zero means to send one byte, so you need a
subtraction instead of an addition.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch addresses the following issues with the pxa2xx FIr driver:
1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.
Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ingo reported that built-in drivers suffered bootup hangs with certain
driver unregistry sequences, due to sysfs breakage.
Do the minimal fix for v2.6.21: only wait if the driver is a module.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've seen this several times on this drive, completely reproducible.
Once it has hung, power needs to be cut from the drive to recover it, a
simple reboot is not enough. So I'd suggest disabling NCQ on this
drive.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
NetXen: Fix hardware access for ppc architecture.
sis190: new PHY support
atl1: save mac address on remove
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark some static arrays as const that aren't and shouldn't be modified, and
remove incorrect static attribute from some variables.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported to work on the WinFast 761GXK8MB-RS motherboard.
Plain 10/100 Mbps.
Signed-off-by: Paul Gibbons <paul@pkami.e7even.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some atl1 boards get their MAC address written directly to the register
by the BIOS during POST, rather than storing it in EEPROM that's
accessible to the driver. If the MAC register on one of these boards
is changed and then the module is unloaded, the permanent MAC address
will be forgotten until the box is rebooted. We should save the
permanent address during removal if we've been messing with it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event. The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.
Update version to 1.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Handle aborting a command after it is sent
IB/mthca: Fix thinko in init_mr_table()
RDMA/cxgb3: Fix resource leak in cxio_hal_init_ctrl_qp()
nmi_cpu_setup() is called from hardirq context and acquires oprofilefs_lock.
alloc_event_buffer() and oprofilefs_ulong_from_user() acquire this lock
without disabling irqs, which could deadlock.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: NCQ is broken on Maxtor 6L250S0
pata_pdc202xx_old: LBA48 bug
libata: IDENTIFY backwards for drive side cable detection
ahci.c: walkaround for SB600 SATA internal error issue
[libata] Disable ACPI by default; fix namespace problems
Fix section mismatch warning by moving data into __devinitdata section.
Add __devinit to initialization functions.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for allocated DVMA memory and granted IRQ line.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.
The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e4d.
This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The tx timeout routine was waking the tx queue conditionally. However,
it must call it unconditionally since the dev_watchdog has halted the tx
queue before calling the timeout function.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nic poll routine was missing the call to the optimized irq routine.
This patch adds the missing call for the optimized path.
See http://bugzilla.kernel.org/show_bug.cgi?id=7950 for more information.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed rx checksum bits. Turn on TCP processing for rx checksum.
Fixed max frame length register write. It wasn't getting set
in multi-port system. Set rx buffer queue length properly
for jumbo frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the rx queue pointer when exiting NAPI poll rather than
at the end of each iteration. Remove unnecessary PCI flushes
that occurred after every write. Now write all regs and
flush once.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was removed in a previous patch to increase performance, but
caused a transmit error for the 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original vendor driver contained a private ether_crc_le() function
that produced an inverted crc. When we changed to the kernel version of
ether_crc_le(), we neglected to undo the inversion. Let's do it now.
Discovered by and patch proffered by Jose Alberto Reguero.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correctly detect when TSO should be used on transmit by looking at the
skb->gso_size rather than seeing if the frame was larger than our MTU.
The old method causes problems when a host with a large (jumbo) MTU is
sending to a host with a small (standard) MTU.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With this applied, my machine has stopped all those painful messages.
dmesg now says :
root@riri:/Kernels# dmesg | grep LBA
ata1.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
ata2.00: 640 sectors, multi 1: LBA
ata3.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
Signed-off-by: Paul Rolland <rol@as2917.net>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In LBA48 mode we have to help the controller to get anything to work. The
chip provides a register giving word counts meant for ATAPI use which we
can use. However we need to load the count in words not bytes..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For drive side cable detection to work correctly, drives need to be
identified backwards such that the slave device releases PDIAG- before
the mater drive tries to detect cable type. ata_bus_probe() was fixed
by commit f31f0cc2f0 but the new EH path
wasn't fixed. This patch makes new EH path do IDENTIFY backwards.
ata_dev_configure() for new devices are still performed master first.
This is to keep the detection messages in forward order.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is a HW issue in ATI SB600 SATA that PxSERR.E should not be
set on some conditions, for example, when there is no media in SATA
CD/DVD drive or media is not ready, AHCI controller fails to execute
ATAPI commands and reports PORT_IRQ_TF_ERR, but ATI SB600 SATA
controller sets PxSERR.E at the
same time, which is not necessary.
This patch is just to ignore the INTERNAL ERROR in such case.
Without this patch, ahci error handler will report many errors as
below:
----------- cut from dmesg -----------
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0
res 51/24:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error)
-------- end cut ---------
Signed-off-by: Conke Hu <conke.hu@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not yet ready to turn on ATA ACPI by default, for either PATA or SATA.
Also, rename the global-scope module parameter variable 'noacpi' to
something more libata-specific, reducing the potential for namespace
collision.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent changes in the specs that were introduced in commit
740ac4fb08 were incorrect and resulted in machine check
errors on the PPC architecture for G PHY's with a revision number equal to 1. The
two offending changes are reverted.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a duplicated leftshift in bcm43xx_radio_set_tx_iq. data_high values are
already leftshifted. Thanks to Michael Buesch for spotting this.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places where the PHY version and revision were interchanged.
These are changed in the specifications on 2/13/07 and now use "analog" instead
instead of "version" to help reduce confusion.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://kvm.qumranet.com/home/avi/kvm:
KVM: always reload segment selectors
KVM: Prevent system selectors leaking into guest on real->protected mode transition on vmx
I2O subsystem has been broken in mainstream several months ago (after
2.6.18). Commit 4aff5e2333 from Jens
Axboe split struct request ->flags into two parts: cmd_type and
cmd_flags.
In i2o layer this patch has replaced flag REQ_SPECIAL by the according
cmd_type. However i2o has used REQ_SPECIAL not as command type but as
driver-specific flag for the debug purposes. As result all i2o requests
have type "special" now, are not processed to the hardware and fail with
I/O error:
i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
unable to read partition table
block-osm: device added (TID: 207): i2o/hda
The following patch removes the extra debug checks without any drawbacks and
restores the normal driver's work.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:eisa_root_register from .text between 'pci_eisa_init' (at offset 0xabf670) and 'virtual_eisa_release'
AFAIK a PCI to EISA bridge isn't anything hotpluggable, so
pci_eisa_init() can become __init.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_register_master from .text between 'spi_bitbang_start' (at offset 0x84e11a) and 'bitbang_work'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_alloc_master from .text between 'butterfly_attach' (at offset 0x84e681) and 'at25_remove'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_new_device from .text between 'butterfly_attach' (at offset 0x84e7e4) and 'at25_remove'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Bob's machine clocksource is selecting PIT over the ACPI PM timer,
because he has the PIIX4 bug. That bug drops the ACPI PM timers rating
to the same as the PIT, so that's why you're getting the PIT.
Realistically, the PIT is much slower then even the triple read ACPI PM,
so the de-ranking code is probably dropping it too far.
So don't drop ACPI PM quite so low if we see the PIIX4 bug.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Bob Tracy <rct@gherkin.frus.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d720bc4b8f partially removed a
private implementation of baud speed decoding. However it doesn't seem
to be complete: after the speed is decoded, it is still being used as an
index to a local speed table (array overrun, no doubt).
This was found by Graham Murray who noticed it caused a 2.6.19 regression
with the SX driver: https://bugs.gentoo.org/170554
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... still not sure why we need this ....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If this mddev and queue got reused for another array that doesn't register a
congested_fn, this function would get called incorretly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All that is missing the the function pointers in raid4_pers.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo reported it on lkml in the thread
"2.6.21-rc5: maxcpus=1 crash in cpufreq: kernel BUG at drivers/cpufreq/cpufreq.c:82!"
This check added to remove_dev is symmetric to one in add_dev and handles
callbacks for offline cpus cleanly.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
failed VM entry on VMX might still change %fs or %gs, thus make sure
that KVM always reloads the segment selectors. This is crutial on both
x86 and x86_64: x86 has __KERNEL_PDA in %fs on which things like
'current' depends and x86_64 has 0 there and needs MSR_GS_BASE to work.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel virtualization extensions do not support virtualizing real mode. So
kvm uses virtualized vm86 mode to run real mode code. Unfortunately, this
virtualized vm86 mode does not support the so called "big real" mode, where
the segment selector and base do not agree with each other according to the
real mode rules (base == selector << 4).
To work around this, kvm checks whether a selector/base pair violates the
virtualized vm86 rules, and if so, forces it into conformance. On a
transition back to protected mode, if we see that the guest did not touch
a forced segment, we restore it back to the original protected mode value.
This pile of hacks breaks down if the gdt has changed in real mode, as it
can cause a segment selector to point to a system descriptor instead of a
normal data segment. In fact, this happens with the Windows bootloader
and the qemu acpi bios, where a protected mode memcpy routine issues an
innocent 'pop %es' and traps on an attempt to load a system descriptor.
"Fix" by checking if the to-be-restored selector points at a system segment,
and if so, coercing it into a normal data segment. The long term solution,
of course, is to abandon vm86 mode and use emulation for big real mode.
Signed-off-by: Avi Kivity <avi@qumranet.com>
After freeing a block there should be no reference to this block.
Signed-off-by: Thomas Viehweger <Thomas.Viehweger@marconi.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Returning -1 causes the probe to stop, but it should just continue
instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix several instances of dvb-core functions using mutex_lock_interruptible
and returning -ERESTARTSYS where the calling function will either never
retry or never check the return value.
These cause a race condition with dvb_dmxdev_filter_free and
dvb_dvr_release, both of which are filesystem release functions whose
return value is ignored and will never be retried. When this happens it
becomes impossible to open dvr0 again (-EBUSY) since it has not been
released properly.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All the radio drivers need video_dev, but they were depending on
VIDEO_DEV!=n. That meant that one could try to compile the driver into
the kernel when VIDEO_DEV=m, which will not work. If video_dev is a
module, then the radio drivers must be modules too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
