pvrusb2: Remove use of volatile for command sequencer; these variables
are set by interrupt-context code and we check their state in such a
manner that there should be no race conditions. This had originally
been done out of paranoia, and I have since been convinced that the
paranoia is not required.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds a default video standard setting to the pvr2_device_desc
structure for describing device types. With this change it is
possible to set a reasonable default standard based on device type.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset allows the pvrusb2 driver to operate a new device type
("GOTVIEW USB2.0 DVD2"). Changes amount to defining a new routing
scheme for the device and adding appropriate table entries into
pvrusb2-devattr.c.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver has been successfully recovering from a crashed
encoder now for over 2 years. I think it's time to reduce the
perceived severity of the warning message. While I'd still very much
like to stop these crashes, the recovery logic is solid enough that
the problem is effectively benign. No point in panicing the users
over it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For Hauppauge 24xxx devices, the IR receiver is a custom piece of
logic that is very specific to the device. The pvrusb2 driver can
virtualize this to make it look like a more normal IR receiver found
in other Hauppauge devices. The decision of whether or not to enable
this virtualization however is a device-specific attribute, thus this
changeset.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The exact routing of video and audio signals within a device is a
device-specific attribute. Hauppauge devices do it one way; other
types of device may route things differently. Unfortunately it is
rather impractical to define chip-specific routing at the device
attribute level, so instead what happens here is that "schemes" are
defined. Each chip level interface implements its part of a given
scheme and the scheme as a whole is made into a device specific
attribute controlled via a table entry in pvrusb2-devattr.c. The only
scheme defined here is for Hauppauge devices, but clearly this opens
the door for other possibilities to follow.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Arrange so that the pvrusb2 driver can optionally work without a
Hauppauge ROM being present - which is fairly important for devices
that happen to not come from Hauppauge. The expected existence of a
Hauppauge ROM is now a device attribute. The tuner type is now also a
device attribute, which is consulted if there is no ROM.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correctly mark when a tuner type is set. Report more faithfully
information about known supported device video standards.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement additional pvrusb2 device info table entries for a device
identifier and a device description. Export this information via the
driver's internal API. Make this information available via the sysfs
driver interface. Also propagate this information into the v4l2
capability structure. An app can now retrieve and report a
descriptive string about the particular type of hardware device it is
operating.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Device-specific driver behavior is now defined by generic device
characteristics rather than by specific device model information.
With this change, the hardware type field can go away, thus this
change.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver currently supports two variants of the Hauppauge
PVR USB2. However there are other hardware types potentially
supportable, but the driver at the moment is not structured to make it
easy to describe these minor variations. This changeset is the first
set of changes to make such additional device support possible.
Device attributes are held in several tables all contained within
pvrusb2-devattr.c; all other device-specific driver behavior now
derives from these tables.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a new implementation for video pipeline control within the
pvrusb2 driver. Actual start/stop of the pipeline is moved to the
driver's kernel thread. Pipeline stages are controlled autonomously
based on surrounding pipeline or application control state. Kernel
thread management is also cleaned up and moved into the internal
control structure of the driver, solving a set up / tear down race
along the way. Better failure recovery is implemented with this new
control strategy. Also with this change comes better control of the
cx23416 encoder, building on additional information learned about the
peculiarities of controlling this part (this information was the
original trigger for this rework). With this change, overall encoder
stability should be considerably improved. Yes, this is a large
change for this driver, but due to the nature of the feature being
worked on, the changes are fairly pervasive and would be difficult to
break into smaller pieces with any semblence of step-wise stability.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver is tearing down its sysfs related pieces in the
incorrect order. This leaves dangling pointers which causes the
kernel device core to oops. The problem has been present virtually
forever but became malignant with the changeover to the way of
handling /sys/class. Fix is just to make sure we don't tear down the
class structure until AFTER the driver instances are deregistered.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver's sysfs implementation had long since implemented a
dummy hotplug function because at the time the kernel would oops
without at least the empty function being present. Today - after
numerous class interface changes in the kernel - this pvrusb2 change
had been dutifully carried forward but an inspection of the kernel
sources shows that it is no longer needed. So remove the dummy
function and its reference. This also solves a recurring backwards
compatibility issue in the pvrusb2 driver as the class interface has
been getting thrashed in the kernel.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
if(!x & y) should either be if(!(x & y)) or if(!x && y)
I made changes as seemed appropriate, but please review
this is against current git.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a minor change to help with tracking the viability of the
encoder chip within the PVR USB2 device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
struct video_device used to define a .hardware field. While
initialized on severl drivers, this field is never used inside V4L.
However, drivers using it need to include the old V4L1 header.
This seems to cause compilation troubles with some random configs.
Better just to remove it from all drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This removes NOP implementations of i2c_algorithm.algo_control.
With this change, there are no implementations of this hook in
the kernel.org tree ... that hook seems about ripe to remove.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The prototypes for the show and store methods of a device_attribute changed in
kernel 2.6.13, but the code in pvrusb2 was never updated. I guess the
DEBUGIFC stuff isn't used much....
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The currently used "struct class_device" will be removed from the
kernel. Here is a patch that converts all users in drivers/media/video/
to struct device.
Reviewed-by: Thierry Merle <thierry.merle@free.fr>
Reviewed-by: Mike Isely <isely@pobox.com>
Reviewed-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* I2C adapters aren't expected to handle I2C_M_NOSTART unless they
really have to. As the pvrusb2 driver doesn't support it, I take it
that it doesn't need it so it shouldn't mention it at all.
* I2C_FUNC_SMBUS_EMUL includes I2C_FUNC_SMBUS_BYTE_DATA so listing
both is redundant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It's useful to see specific details for how the pvrusb2 driver is
figuring out things related to the video standard, independent of
other initialization activities. So let's set up a separate debug
mask bit for this and turn it on.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The v4l tveeprom logic tells us what video standards are supported by
the hardware, however it doesn't directly tell us what should be the
preferred initial standard. For example "NTSC/NTSC-J" devices are
reported by tveeprom as support NTSC-M and PAL-M, and while that might
be true, in the vast majority of cases NTSC-M is really what the user
is going to want. However the driver previously just arbitrarily
picked the "lowest numbered" standard as the initial default, which in
that case would have been PAL-M. (And making matters more confusing -
this only caused real problems on 24xxx devices because the saa7115 on
29xxx seems to autodetect the right answer anyway.) This change
implements an algorithm that uses the set of "supported" standards as
a hint to decide on the initial standard. This algorithm ONLY comes
into play if the driver isn't specifically told what to do; said
another way - the user can always still change the standard via the
sysfs interface, via the usual V4L methods, or even specified as a
module parameter. The idea here is only to pick a better starting
point if the user (or app) doesn't otherwise do something to set the
standard; otherwise this change has no real impact.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a bunch of cleanup in various places to improve behavior based
on actual device type being driven. While this doesn't actually
affect operation with existing devices, it cleans things up so that it
will be easier / more deterministic when other devices are added.
Ideally we should make stuff like this table-driven, but for now this
is just a series of small incremental (read: safe) improvements.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver already has a method for extracting the FX2's
program memory back out to a user application; this ability is used to
facilitate manual firmware extraction as per the procedure documented
on the pvrusb2 web site. This change follows that pattern and
implements a corresponding method to grab the binary contents of the
PVR USB2 prom (which for PVR USB2 devices can contain information in
addition to the usual Hauppauge metadata).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver should now pass the 'busy' state of the device to the cx2341x
module whenever controls are set or tried. -EBUSY will be returned if
the device is busy and the user attempts to modify certain 'dangerous'
controls. It concerns controls that change the audio or video
compression mode and bitrates.
The cx88-blackbird and pvrusb2 drivers currently always pass '0' (not busy)
to the cx2341x, effectively keeping the old behavior for now.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Anyone using multiple PVR USB2 devices really only want one of them
acting as the actual IR receiver.
Implemented here is a new per-instance module option (ir_mode) which is
a flag to enable the IR receiver. The default is enabled.
IR reception is disabled by blocking access to the IR receiver chip in
the device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch originated with Servaas Vandenberghe <vdb128@picaros.org>
and has been further developed a bit (to preserve saa7115 behavior).
These changes allow for correct operation of PAL-60 video (Servaas
tested this against a PAL-B/G tuner with the video standard overridden
as a module option).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
sysfs is now completely out of driver/module lifetime game.
After deletion, a sysfs node doesn't access anything outside sysfs
proper, so there's no reason to hold onto the attribute owners.
Note that often the wrong modules were accounted for as owners leading
to accessing removed modules.
This patch kills now unnecessary attribute->owner.
Note that with this change, userland holding a sysfs node does not
prevent the backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the following
message:
http://article.gmane.org/gmane.linux.kernel/510293
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver use a semaphore as mutex. use the mutex API instead
of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The V4L2 API requires a unique bus_info string returned as part of the
v4l2_capability structure. These changes gather up the USB address
information, from the underlying device, into a string and report that
out through v4l2 and via sysfs (for completeness).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The chip matching in struct v4l2_register for VIDIOC_DBG_G/S_REGISTER
was rather primitive. It could not be extended to other busses besides
i2c and it lacked a way to.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver previously rejected encoder firmware whose size was
not a multiple of 8192. But this is a false check because it's
possible to find cx23416 firmware whose size doesn't conform to this
limit. So change the firmware loader implementation to be more
forgiving of the image size.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support 64 bit register IDs internally. Only allow root access to
this API (for both set and get). Note that actual 64 bit access only
becomes possible once the definition for v4l2_register is updated, but
this change clears the way for it from the viewpoint of the pvrusb2
driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tweak the encoder setup in order to stop it from corrupting the video
data when there is a disruption in the data flow (e.g. a channel change).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update the implementation of the communication protocol for operating
the encoder, using updated knowledge about the encoder.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several special-case FX2 commands were being issued through
pvr2_write_u16() and pvr2_write_8(), but there's really nothing
special case about them. These date from a very early time in the
driver development. This patch removes these functions and replaces
their use with calls to pvr2_send_request.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a maintainability cleanup; use nice names for all the FX2
commands instead of raw bytes. This way we can easily find where we
issue FX commands.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The direct register access ioctls were defined as kernel internal only,
but they are very useful for debugging hardware from userspace and are
used as such. Officially export them.
VIDIOC_INT_[SG]_REGISTER is renamed to VIDIOC_DBG_[SG]_REGISTER
Definition of ioctl and struct v4l2_register is moved from v4l2-common.h
to videodev2.h.
Types used in struct v4l2_register are changed to the userspace
exportable versions (u32 -> __u32, etc).
Use of VIDIOC_DBG_S_REGISTER requires CAP_SYS_ADMIN permission, so move
the check into the video_ioctl2() dispatcher so it doesn't need to be
duplicated in each driver's call-back function. CAP_SYS_ADMIN check is
added to pvrusb2 (which doesn't use video_ioctl2).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pvrusb2 have only one tuner inside. However, as it were not handling
index, a call to v4l-info were returning as if it were an infinite
number of tuners:
$ v4l-info|grep VIDIOC_G_TUNER |head -5
VIDIOC_G_TUNER(0)
VIDIOC_G_TUNER(1)
VIDIOC_G_TUNER(2)
VIDIOC_G_TUNER(3)
VIDIOC_G_TUNER(4)
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pvrusb2-encoder.c: In function 'pvr2_encoder_cmd':
pvrusb2-encoder.c:195: warning: format '%u' expects
type 'unsigned int', but argument 3 has type 'long unsigned int'
pvrusb2-encoder.c:205: warning: format '%u' expects
type 'unsigned int', but argument 3 has type 'long unsigned int'
pvrusb2-encoder.c: In function 'pvr2_encoder_vcmd':
pvrusb2-encoder.c:303: warning: format '%u' expects
type 'unsigned int', but argument 3 has type 'long unsigned int'
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the previous patch, mplayer started but was polling the video
device forever without any video actually coming out. Further analysis
showed that it does a VIDIOC_S_FMT with width and height set to -1 (!!!).
The code handling this only cares that both are lower than the minimum
range allowed so it ends up setting the size to 19x17 (!!) This pretty
much breaks the encoder here. Even if this breakage is yet another (TM)
result of my setup, setting the size to 19x17 by default would surprise
most users IMHO.
So, special case for -1 and interpret this to be a request for the
default size, please. Users can then set their favorite size both
through mplayer and through sysfs.
With this patch, mplayer finally works in pvr:// mode (not that we
really gain anything over operating it through sysfs with lirc,
sometime I might actually get off my lazy a** and contribute this
setup too)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This should allow mplayer pvr:// to start. The trick is that no matter
what actual input we use under this "fake" one, it will be able to do
stereo :-)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Audio mode changes are not private to the audio chip - other I2C
modules need to see this as well. And since the command in question
is VIDIOC_S_TUNER which is a standard v4l2 command, we really should
be broadcasting it out. This change sets up a broadcast pathway for
VIDIOC_S_TUNER and also eliminates the now redundant code from the
audio chip handler.
This fix enables stereo reception for the FM radio
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Attempts to enumerate or operate on a group of EXT_CTRLS where the
group size is zero is OK; don't fail on such operations. At least one
application uses this to probe for the existence of this API so let it
succeed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This bug caused uninitalized data to be returned during a G_TUNER status poll.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The lack of a break statement in the handling of VIDIOC_S_TUNER caused
errors to result. Fixed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than hardcoding frequency ranges everywhere, rely on
VIDIOC_G_TUNER results wherever we can.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The automodeswitch control was a feature that enable automatic radio /
tv switching based on the selected frequency. However since frequency
ranges can overlap and also since apparently in some cases it's
possible for the same frequency range to be both tv and radio in a
specific region, then this feature can't safely work. So it's removed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up use of VIDIOC_G_TUNER; we now correctly gather info from all
the I2C client modules. Also abide by V4L2_TUNER_CAP_LOW
appropriately.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Switch back to the previous input selection when the radio device is
closed - but only do that if the current input selection is still the
radio (i.e. it appears that it hasn't been messed with).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the input is switched by opening /dev/radioX, we must also commit
that change into the driver core.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up and tighten logic involving stream configuration. This
mainly involves changes to pvrusb2-v4l2.c, where we better clarify how
we use the stream configuration enum and implement a cleaner means to
control streaming for a given device node.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default volume of 65535 is too high. Make is something smaller.
Note that this _only_ changes the default value. Specifically, there
are no scaling or other more intrusive changes here. I'm just sick of
constantly having to reduce the volume every time I plug in and test
the device! (And unfortunately we can't do a better fix like scaling
the volume so that 65535 makes sense because doing so will screw up
any app - like MythTV - which expects the old scaling.) Too bad V4L
controls don't have better defined ranges.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trying to temporarily check that the stream is not claimed during open
of the radio device is at best a race condition. What's to stop
another app from claiming the stream anyway the instant after the
check is done? The implementation for this was dicey anyway. So it's
removed. The only "price" for this is that if /dev/radioX is opened
while streaming video, then the video stream is just going to switch
to radio mode anyway. If a user does this, he gets what he expects...
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Separate track radio versus tv frequency so that when we switch modes
we can also switch to a sane frequency appropriate for the mode. Also
implement logic to automate mode switching in certain cases.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement new method for doing integer range checking, so that we can
more intelligently range-check radio and tv ranges at once.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes implement correct audio routing for radio mode on a
24xxx device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Report and set correctly converted frequency to/from a V4L2 app.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frequency units in V4L2 are apparently different when in radio mode
compared to tv mode. Why? Who knows. This change adapts the driver
appropriately - so that internally we always only deal in Hz and don't
have to muck with craziness like this.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A conversion from Hz to V4L frequency units was accidentally removed
by an earlier change. Restore it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We can't allocate v4l device structures in a block, since the v4l core
governs when each device actually gets freed. This bug was introduced
as part of the core radio implementation. Fix it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support specification of vbi and radio device minor numbers in a
manner similar to the video device minor number.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ensure we don't accidentally broadcast the standard while in radio mode.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The initial radio implementation used different units for tuning when
in radio mode. This changes everything to Hz.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use separate enum for get/store of minor number; we want pvr2_config
to go away eventually and since it really means something different,
don't use it here
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The "main" V4L2 interface patch. This is yet very incomplete, incorrect and
probably inappropriate for inclusion as-is, but at least with this I 'm able
to tune and play radio through a V4L2 program (pvr-radio.c, a "thumb" version
of ivtv-radio.c with just the essentials).
Therefore, it kinda gives an idea of what is needed to support this, hm,
interface (partly used also by e.g., kradio). Please point out any mistakes
on this code. I 'm sure I 'm messing up some struct initialization somewhere
but currently I 'm too lazy to actually think this through until I complete
the functionality (e.g., handle the VIDIOC_S_STD, ENUMINPUT, etc ioctls
appropriately).
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add (and expose) a new function, pvr2_channel_check_stream_no_lock(), in
pvrusb2-context.c. This is hopefully the last V4L2 interface related patch
to change anything outside pvrusb2-v4l2.c.
We need this to implement the open() for the radio device. The reason is
that within the *enter_context() section of open() we need to ensure nobody
is streaming and if we cannot, we should cleanup after ourselves and return
-EBUSY. We cannot just use claim_stream() because:
1) That would cause a deadlock trying to re-acquire the context lock
2) We only need to ensure that nobody is streaming. We don't need to
actually acquire the stream.
Again, this is a kinda ugly patch. Feel free to improve.
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the first patch in preparation of the V4L2/IVTV radio interface.
It does away with the assumption of only one minor per device. It also
adds a file to show the radio minor as well. This can be useful for a
program like pvr-radio.c (when it grows up), since this way it can search
for the minor of the /dev/radioX device it opened and use the video minor
of the same driver instance to get to the actual stream.
The implementation looks kinda ugly. Feel free to improve (that is the
reason behind separate patches anyway).
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the previous patch we exploited the get_{min,max}_value facility to adjust
min/max allowable frequencies on the fly, depending on tuner mode.
Unfortunately, this facility was not used inside the *sym_to_val() function
that translates what we echo to sysfs, which means we got an -ERANGE despite
asking for a frequency between what we read to be min/max.
This patch corrects this small omission.
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the logic that:
a) Ensures /sys/class/pvrusb2/sn-*/ctl_frequency/{max,min}_val are
"automagically" reset to sane values on each mode change.
b) Allows tuning to a radio frequency by something like:
echo `perl -e "print int(94.9*16000 + 0.5)"` \
> /sys/class/pvrusb2/sn-*/ctl_input/cur_val
The trick was to take advantage of the already existing .get_{min,max}_value
function pointers in pvr2_ctrl, to "dynamically override" the hardcoded values
for min/max frequency at runtime.
For a moment I thought to dispose of the hardcoded MIN/MAX_FREQ and use the
hirange/lowrange fields of the v4l2_tuner struct instead, but then I see that
tuner-core.c kinda hardcodes these as well, so I decided to not bother.
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is the logic that supports switching modes via e.g.,
echo radio > /sys/class/pvrusb2/sn-*/ctl_input/cur_val.
To do the mode switching we need to:
a) broadcast AUDC_SET_RADIO and
b) issue the CX2341X_ENC_MUTE_VIDEO command to the encoder.
The first is done by adding a new pvr2_i2c_op and having it trigger on
input change, the second by adding this command in pvr2_encoder_start()
and requesting an encoder restart on input change by setting
stale_subsys_mask appropriately.
The clues about AUDC_SET_RADIO and CX2341X_ENC_MUTE_VIDEO were kindly
provided by Hans Verkuil on the pvrusb2 mailing list. The idea to
implement mode switching this way (on input change) is due to Mike Isely.
Why AUDC_SET_RADIO/VIDIOC_S_STD are used for switching? I can 't be sure,
but I think this can be traced to a cornell student being the first to
implement radio support in ivtv "as a different standard". I think the
rest just evolved from there (it 's in the ivtv ML archives).
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The commands CX2341X_DEC_SET_AUDIO_OUTPUT, CX2341X_DEC_SET_AV_DELAY and
CX2341X_ENC_SET_3_2_PULLDOWN are not implemented in the Conexant firmware.
So these commands are removed. This also means that the V4L2_CID_MPEG_VIDEO_PULLDOWN
control in cx2341x.c and pvrusb2-hdw.c is removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Declare the parent device of i2c_adapter devices each time we can
easily do so. It makes the i2c_adapter appear at the right place in
the device tree, rather than as a platform device.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: v4l-dvb-maintainer@linuxtv.org
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix long-standing issue which prevented use of 24xxx devices at any
horizontal resolution other an 720. The problem is in the cx25840
module, if no attempt is made to initialize VBI there. Such a thing
should not be needed, but the pvrusb2 driver is updated now to deal
with this.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Unlike 29xxx devices, the 24xxx model series does not have a dedicated
I2C device for reception of IR codes. Instead IR is handled directly
by the FX2 microcontroller and the results are communicated via
commands to the FX2. Rather than implement a whole new IR reception
pathway for 24xxx devices, this changeset instead emulates the
presence of the 29xxx device's I2C based IR receiver by intercepting
commands to that chip and issuing appropriate FX2 commands to do the
needed action. This has the result of allowing all the usual IR
frameworks (ir-kbd-i2c or lirc) to continue working unmodified for
24xxx devices.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Fix sparse NULL usage warnings:
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:714:14: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:715:16: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1079:10: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:224:58: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Use NULL instead of 0 for pointer value, eliminate sparse warnings.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The function prototype needed in pvrusb2-v4l2.c has been moved to
v4l2-dev.h. Track that change.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A previous attempt to deal with the upcoming loss of
video_set_drvdata() and video_get_drvdata() resulted in logic which
causes a circular locking dependency - also known as a deadlock. This
changeset attacks the problem in a different manner, using a technique
that no longer requires the problematic mutex (or that private global
array either).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement VIDIOC_INT_SET_REGISTER and VIDIOC_INT_GET_REGISTER for the
pvrusb2 driver. This is a debugging aid which will not be enabled
unless CONFIG_VIDEO_ADV_DEBUG has been enabled.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The CONFIG_VIDEO_PVRUSB2_24XXX is not nearly as "experimental" as the
description suggests. So refine the description to better match reality.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix broken build when 24XXX support is not selected. This is required
due to the requirement of removing 24XXX ifdef's from the driver
source.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver resolution limits are now programmed the following
way, based on empirical measurements of the hardware:
Vertical max: 480 for NTSC, 576 otherwise
Vertical min: 75 for 24xxx, 17 otherwise
Horizontal max: 720
Horizontal min: 720 for 24xxx, 19 otherwise
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for 24xxx devices was previously explicitly bracketed with
CONFIG_VIDEO_PVRUSB2_24XXX inside the code because we didn't trust the
stability of these changes. We trust it now; so there's no reason to
leave this out of the driver anymore.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The extra argument makes it possible to reset subsystems of a chip if
that is supported.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several boards on V4L that can work with several different
helper modules for audio/video encoding/decoding and similar stuff.
This patch adds the capability of choicing between autoselecting the
pertinent helper modules for each driver, or to manually selecting
them.
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c: In function 'set_standard':
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c:33: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'v4l2_std_id'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change causes the pvrusb2 driver to limit horizontal resolution
to be only 720 if 24xxx device hardware is being used. This is a
workaround for an unsolved problem in the driver where if the
resolution is set to something other than 720 the video quality will
be _seriously_ degraded. It only happens on 24xxx devices (29xxx are
unaffected by the problem and unaffected by this change). Once the
problem is finally solved, this small change can be removed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The internal control implementation in the pvrusb2 driver normally
encodes integer range limits using literal values in a const
structure. This change adds two function pointers, which if not null
will be called through in order to determine integer min / max
values.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 implementation for VIDIOC_[S|TRY]_FMT was hardcoding
limits on the range for allowed resolution, but it would be much
better if we instead just queried the internal control for these
values. This then opens the door for the driver to adjust these
limits based on the detected hardware.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a few miscellaneous issues in the pvrusb2 driver related to use of
the new mpeg controls. This also should fix problems involving
update of the saa7115 / cx25840 configuration as control changes are made.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since kernel include autoconf.h via command line, those config.h inclusion
can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Take note of which sysfs files / groups that the pvrusb2 successfully
creates and only delete those specific items when tearing things
down. (Previously we just blindly tore everything down every time.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Check __must_check warnings for class_device_register and class_device_create_file
video_device_create_file was declared as a void, but instead should
return the int value of class_device_create_file.
Move the check from bttv-driver.c into v4l2-dev.h, because all other
callers of video_device_create_file must also be checked.
Replace the call to class_device_create_file in videodev.c with
video_device_create_file, as defined in v4l2-dev.h, so that the
return value of class_device_create_file will be checked.
Check the return value of class_device_register in videodev.c and
pvrusb2-sysfs.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 unused global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously the pvrusb2 driver was conditionalizing printing of the
device register / unregister messages against a debug mask. This sort
of information should always appear, thus this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A card number is not unique enough. Instead, let the caller specify the
prefix of the status messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement V4L2 driver for the Hauppauge PVR USB2 TV tuner.
The Hauppauge PVR USB2 is a USB connected TV tuner with an embedded
cx23416 hardware MPEG2 encoder. There are two major variants of this
device; this driver handles both. Any V4L2 application which
understands MPEG2 video stream data should be able to work with this
device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
