Since mmc_spi.h uses irqreturn_t type, it should include appropriate
header, otherwise build will break if users didn't include it (some of
them do not use interrupts).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
8250 Serial Driver: revert extra IRQ flag definition patch
Blackfin arch: update anomaly headers from toolchain trunk
Blackfin arch: Remove bad and usless code
Blackfin arch: Fix bug - set corret SSEL and IRQ to enable AD7877 on BF527
Blackfin arch: Fix typo. it should be _outsw_8
Blackfin arch: Cleanup no functional changes
Gcc might re-order MMIO accessors vs. surrounding consistent
memory accesses, which is a "bad thing", and could break drivers.
This fixes it by adding a "memory" clobber to the MMIO accessors,
which should prevent gcc from doing that reordering.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: notify on empty
virtio: force callback on empty.
virtio_blk: fix endianess annotations
virtio_config: fix len calculation of config elements
virtio_net: another race with virtio_net and enable_cb
virtio: An entropy device, as suggested by hpa.
virtio_blk: allow read-only disks
lguest: fix ugly <NULL> in /proc/interrupts
virtio: set device index in common code.
virtio: virtio_pci should not set bus_id.
virtio: bus_id for devices should contain 'virtio'
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
lguest: use ioremap_cache, not ioremap
The SW_RADIO code for EV_SW events has a name that is not descriptive
enough of its intended function, and could induce someone to think
KEY_RADIO is its EV_KEY counterpart, which is false.
Rename it to SW_RFKILL_ALL, and document what this event is for. Keep
the old name around, to avoid userspace ABI breaks.
The SW_RFKILL_ALL event is meant to be used by rfkill master switches. It
is not bound to a particular radio switch type, and usually applies to all
types. It is semantically tied to master rfkill switches that enable or
disable every radio in a system.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
virtio tests with guests larger than 4 GB revealed that the dma_addr_t
definition for s390 did not make it into the 64bit world.
This patch changes the definition on s390 to have an u64 on 64bit and
u32 on 32bit systems.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
virtio allows drivers to suppress callbacks (ie. interrupts) for
efficiency (no locking, it's just an optimization).
There's a similar mechanism for the host to suppress notifications
coming from the guest: in that case, we ignore the suppression if the
ring is completely full.
It turns out that life is simpler if the host similarly ignores
callback suppression when the ring is completely empty: the network
driver wants to free up old packets in a timely manner, and otherwise
has to use a timer to poll.
We have to remove the code which ignores interrupts when the driver
has disabled them (again, it had no locking and hence was unreliable
anyway).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since commit 72e61eb40b (virtio: change config
to guest endian) config space is no longer fixed endian.
Lets change the virtio_blk_config variables.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty,
This patch is a prereq for the virtio_blk blocksize patch, please apply it
first.
Adding an u32 value to the virtio_blk_config unconvered a small bug the config
space defintions:
v is a pointer, to we have to use sizeof(*v) instead of sizeof(v).
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Note that by itself, having a "hardware" random generator does very
little: you should probably run "rngd" in your guest to feed this into
the kernel entropy pool.
Included:
virtio_rng: dont use vmalloced addresses for virtio
If virtio_rng is build as a module, random_data is an address
in vmalloc space. As virtio expects guest real addresses, this
can cause any kind of funny behaviour, so lets allocate
random_data dynamically with kmalloc.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Hello Rusty,
sometimes it is useful to share a disk (e.g. usr). To avoid file system
corruption, the disk should be mounted read-only in that case. This patch
adds a new feature flag, that allows the host to specify, if the disk should
be considered read-only.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Create the dev_set_name function now so that various subsystems can
start changing over to it before other changes in 2.6.27 will make it
compulsory.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
improve the sysbench ramp-up phase and its peak throughput on
a 16way NUMA box, by turning on WAKE_AFFINE:
tip/sched tip/sched+wake-affine
-------------------------------------------------
1: 700 830 +15.65%
2: 1465 1391 -5.28%
4: 3017 3105 +2.81%
8: 5100 6021 +15.30%
16: 10725 10745 +0.19%
32: 10135 10150 +0.16%
64: 9338 9240 -1.06%
128: 8599 8252 -4.21%
256: 8475 8144 -4.07%
-------------------------------------------------
SUM: 57558 57882 +0.56%
this change also improves lat_ctx from 6.69 usecs to 1.11 usec:
$ ./lat_ctx -s 0 2
"size=0k ovr=1.19
2 1.11
$ ./lat_ctx -s 0 2
"size=0k ovr=1.22
2 6.69
in sysbench it's an overall win with some weakness at the lots-of-clients
side. That happens because we now under-balance this workload
a bit. To counter that effect, turn on NEWIDLE:
wake-idle wake-idle+newidle
-------------------------------------------------
1: 830 834 +0.43%
2: 1391 1401 +0.65%
4: 3105 3091 -0.43%
8: 6021 6046 +0.42%
16: 10745 10736 -0.08%
32: 10150 10206 +0.55%
64: 9240 9533 +3.08%
128: 8252 8355 +1.24%
256: 8144 8384 +2.87%
-------------------------------------------------
SUM: 57882 58591 +1.21%
as a bonus this not only improves the many-clients case but
also improves the (more important) rampup phase.
sysbench is a workload that quickly breaks down if the
scheduler over-balances, so since it showed an improvement
under NEWIDLE this change is definitely good.
Yanmin Zhang reported:
Comparing with 2.6.25, volanoMark has big regression with kernel 2.6.26-rc1.
It's about 50% on my 8-core stoakley, 16-core tigerton, and Itanium Montecito.
With bisect, I located the following patch:
| 18d95a2832 is first bad commit
| commit 18d95a2832
| Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
| Date: Sat Apr 19 19:45:00 2008 +0200
|
| sched: fair-group: SMP-nice for group scheduling
Revert it so that we get v2.6.25 behavior.
Bisected-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
> +#define ARCH_KMALLOC_MINALIGN (sizeof(long) * 2)
> +#define ARCH_SLAB_MINALIGN (sizeof(long) * 2)
This doesn't work if SLAB is selected and slab debugging is enabled as
these are passed to the preprocessor, and the preprocessor doesn't
understand sizeof.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: fix RCU problem in cfq_cic_lookup()
block: make blktrace use per-cpu buffers for message notes
Added in elevator switch message to blktrace stream
Added in MESSAGE notes for blktraces
block: reorder cfq_queue to save space on 64bit builds
block: Move the second call to get_request to the end of the loop
splice: handle try_to_release_page() failure
splice: fix sendfile() issue with relay
Specify the minimum slab/kmalloc alignment to be 8 bytes. This fixes a
crash when SLOB is selected as the memory allocator. The FRV arch needs
this so that it can use the load- and store-double instructions without
faulting. By default SLOB sets the minimum to be 4 bytes.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in the header guard of asm/ipc.h.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently it uses a single static char array, but that risks
being corrupted when multiple users issue message notes at the
same time. Make the buffers dynamically allocated when the trace
is setup and make them per-cpu instead.
The default max message size of 1k is also very large, the
interface is mainly for small text notes. So shrink it to 128 bytes.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Allows messages to be inserted into blktrace streams.
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Problem: An application violating the architectural rules regarding
operation dependencies and having specific Register Stack Engine (RSE)
state at the time of the violation, may result in an illegal operation
fault and invalid RSE state. Such faults may initiate a cascade of
repeated illegal operation faults within OS interruption handlers.
The specific behavior is OS dependent.
Implication: An application causing an illegal operation fault with
specific RSE state may result in a series of illegal operation faults
and an eventual OS stack overflow condition.
Workaround: OS interruption handlers that switch to kernel backing
store implement a check for invalid RSE state to avoid the series
of illegal operation faults.
The core of the workaround is the RSE_WORKAROUND code sequence
inserted into each invocation of the SAVE_MIN_WITH_COVER and
SAVE_MIN_WITH_COVER_R19 macros. This sequence includes hard-coded
constants that depend on the number of stacked physical registers
being 96. The rest of this patch consists of code to disable this
workaround should this not be the case (with the presumption that
if a future Itanium processor increases the number of registers, it
would also remove the need for this patch).
Move the start of the RBS up to a mod32 boundary to avoid some
corner cases.
The dispatch_illegal_op_fault code outgrew the spot it was
squatting in when built with this patch and CONFIG_VIRT_CPU_ACCOUNTING=y
Move it out to the end of the ivt.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Based on Roland's patch. This approach was suggested by Austin Clements
from the very beginning, and then by Linus.
As Austin pointed out, the execing task can be killed by SI_TIMER signal
because exec flushes the signal handlers, but doesn't discard the pending
signals generated by posix timers. Perhaps not a bug, but people find this
surprising. See http://bugzilla.kernel.org/show_bug.cgi?id=10460
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Austin Clements <amdragon+kernelbugzilla@mit.edu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
vlan: Use bitmask of feature flags instead of seperate feature bits
fmvj18x_cs: add NextCom NC5310 rev B support
xirc2ps_cs: re-initialize the multicast address in do_reset
3C509: rx_bytes should not be increased when alloc_skb failed
NETFRONT: Use __skb_queue_purge()
VIRTIO: Use __skb_queue_purge()
phylib: do EXPORT_SYMBOL on get_phy_id
netlink: Fix nla_parse_nested_compat() to call nla_parse() directly
WAN: protect HDLC proto list while insmod/rmmod
drivers/net/fs_enet: remove null pointer dereference
S2io: Version update for napi and MSI-X patches
S2io: Added napi support when MSIX is enabled.
S2io: Move all the transmit completions to a single msi-x (alarm) vector
drivers/net/ehea - remove unnecessary memset after kzalloc
au1000_eth: remove useless check
Blackfin EMAC Driver: Removed duplicated include <linux/ethtool.h>
cpmac bugfixes and enhancements
e1000e: use resource_size_t, not unsigned long, for phys addrs
net/usb: add support for Apple USB Ethernet Adapter
uli526x: add support for netpoll
...
Align i2c_device_id.driver_data to 8 bytes to not fail on crossbuilds.
(Added in d2653e92732bd3911feff6bee5e23dbf959381db.)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
global_reg_snapshot shouldn't be visible in our userspace headers.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: prevent PGE flush from interruption/preemption
x86: use explicit copy in vdso_gettimeofday()
namespacecheck: automated fixes
x86/xen: fix arbitrary_virt_to_machine()
x86: don't read maxlvt before checking if APIC is mapped
x86: disable TSC for sched_clock() when calibration failed
x86: distangle user disabled TSC from unstable
x86: fix setup of cyc2ns in tsc_64.c
for_each_pgdat() was renamed to for_each_online_pgdat() and kerneldoc
comments should be updated accordingly.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes various gpio-related build errors (mostly potential)
reported in part by Russell King and Uwe Kleine-König.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To keep backwards compatibility, reverse the meanings of these flags so
that when they are not set, the driver uses the original behvaiour.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.
For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.
We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
- We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
which causes the recovery not be be checkpointed.
- We remove spares and then re-added them which loses important state
information.
The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed. If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error. So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.
Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded). Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.
Issue: If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available, do we want to:
1/ complete the current rebuild, then go back and rebuild the new spare or
2/ restart the rebuild from the start and rebuild both devices in
parallel.
Both options can be argued for. The code currently takes option 2 as
a/ this requires least code change
b/ this results in a minimally-degraded array in minimal time.
Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some configurations, a raid6 resync can be limited by CPU speed
(Calculating P and Q and moving data) rather than by device speed. In
these cases there is nothing to be gained byt serialising resync of arrays
that share a device, and doing the resync in parallel can provide benefit.
So add a sysfs tunable to flag an array as being allowed to resync in
parallel with other arrays that use (a different part of) the same device.
Signed-off-by: Bernd Schubert <bs@q-leap.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill the trivial and rather pointless file_path wrapper around d_path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a proper extern for mdp_major in include/linux/raid/md.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atomic_t type is 32bit but a 64bit system can have more than 2^32
pages of virtual address space available. Without this we overflow on
ludicrously large mappings
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<linux/types.h> can't be used together with <sys/ustat.h> because they
both define struct ustat:
$ cat test.c
#include <sys/ustat.h>
#include <linux/types.h>
$ gcc -c test.c
In file included from test.c:2:
/usr/include/linux/types.h:165: error: redefinition of 'struct ustat'
has been reported a while ago to debian, but seems to have been
lost in cat fighting: http://bugs.debian.org/429064
Signed-off-by: maximilian attems <max@stro.at>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the InstaShield IS-400 four port RS-232 PCI card.
Signed-off-by: Ignacio García Pérez <iggarpe@t2i.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
