If SmartFan IV mode was configured at startup, it should be possible
to re-enable it later on.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
For newer chips, several registers are banked and thus need to be 16 bit.
Also, register addresses change.
To prepare for those chips, convert affected register arrays to 16 bit,
and change access to those registers to array pointers in struct w83627ehf_data.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Add support for 4th temperature sensor on W83677HG-B.
Display temperature labels on W83677HG-B to report temperature sources.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Assume that each register is banked, and set the bank for each access.
Cache the bank number so it only needs to be set if it changes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This cleanup fixes most of the checkpatch warnings and errors in the w83627ehf
driver. Remaining warnings and errors are left untouched on purpose to avoid
making the code less readable.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This patch unifies temperature register access, and replaces simple_strtoXXX
with strict_strtoXXX throughout the driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
According to the datasheet for Winbond W83627DHG the proper way to exit
the Extended Function Mode is to write 0xaa to the EFER(0x2e or 0x4e).
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for W83667HG-B (very similar to the W83667HG).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
- Moved fan pwm register array pointers into per-instance data.
- Only read fan pwm data for installed/supported fans.
- Update fan max output and fan step output information from data in
registers.
- Create max_output and step_output attribute files only if respective
fan pwm registers exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level. Add control of rate of change of fan output
level. These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority. Add
support for constant fan speed and proportional-response operations modes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers should be including <linux/io.h> instead of <asm/io.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Frank Seidel <frank@f-seidel.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Madhu <madhu.chinakonda@gmail.com>
The pin for in6 and temp3 is shared on the W83667HG, so only one of
these features can be supported on any given system. Let the driver
select which one depending on the temp3 disabled bit.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.
At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use positive logic for fan pin variables (variable is set if pin is
used for fan), instead of negative logic which is error prone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Gong Jun <JGong@nuvoton.com>
This patch fixes a number of cases where things were not properly
cleaned up when acpi_check_resource_conflict() returned an error,
causing oopses such as the one reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=483208
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Check for ACPI resource conflicts in hwmon drivers. I've included
all Super-I/O and PCI drivers.
I've voluntarily left out:
* Vendor-specific drivers: if they conflicted on any system, this would
pretty much mean that they conflict on all systems, and we would know
by now.
* Legacy ISA drivers (lm78 and w83781d): they only support chips found
on old designs were ACPI either wasn't supported or didn't deal with
thermal management.
* Drivers accessing the I/O resources indirectly (e.g. through SMBus):
the checks are already done where they belong, i.e. in the bus drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
While the W83627EHF/EHG has only 6 VID pins, the W83627DHG has 8 VID
pins, to support VRD 11.0. Add support for this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
While it is possible to force SMBus-based hardware monitoring chip
drivers to drive a not officially supported device, we do not have this
possibility for Super-I/O-based drivers. That's unfortunate because
sometimes newer chips are fully compatible and just forcing the driver
to load would work. Instead of that we have to tell the users to
recompile the kernel driver, which isn't an easy task for everyone.
So, I propose that we add a module parameter to all Super-I/O based
hardware monitoring drivers, letting advanced users force the driver
to load on their machine. The user has to provide the device ID of a
supposedly compatible device. This requires looking at the source code or
a datasheet, so I am confident that users can't randomly force a driver
without knowing what they are doing. Thus this should be relatively safe.
As you can see from the code, the implementation is pretty simple and
unintrusive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The VID input level change has been reported to cause trouble. Be more
careful in this respect:
* Only change the level on the W83627EHF/EHG. The W83627DHG is more
complex in this respect.
* Don't change the level if the VID pins are in output mode.
* Only set the level to TTL if VRM 9.x is used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Convert from class_device to device for hwmon_device_register/unregister
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
- replace differing temperature variable types by long
- use strtol() instead of strtoul() for conversion
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Don't assume that the default bank is 0. For one thing, we don't even
set it to 0 when the driver is loaded, so the initial state might be
different. For another, something (say, the BIOS) might access the chip
and leave with the bank set to something different, so assuming that
the bank value is 0 is not safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch forces the driver to read the fan divider values during early init.
Otherwise, a call to store_fan_min() could access uninitialized variables.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We don't need to initialize fan_min in this driver, as the fan_div
attributes are read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for the w83627ehf thermal sensor types. I made them read-only,
as the BIOS is supposed to set them up properly. This information makes it
easier to find out which temperature channel corresponds to the CPU.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
If VBAT monitoring is disabled, enable it. Original patch from
an anonymous contributor on the lm-sensors trac system:
http://lm-sensors.org/ticket/2218
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The W83627EHF and similar chips have 6 VID input pins, add support
for them. The driver changes the input voltage level automatically
if the current setting is not correct for the detected CPU model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* I have experimental evidence that the W83627EHG needs more than 1
second to refresh all the measured values. Increase the caching time to
1.5 second.
* When changing a fan clock divider, the corresponding fan speed
measurement register is no longer valid, until the next time the chip
will refresh it. One way to fix this is to pretend that the cache is
still valid for one more period (1.5 second.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
If the Super-I/O device is disabled, it is likely the BIOS has a good
reason for leaving it disabled, so give a warning when enabling it --
it's not likely to be wired correctly or be able to give good data.
Also, if the Super-I/O device is configured with an address of 0, the
driver refuses to initialize it.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Remove i2c-isa from the w83627ehf driver, and use a platform driver
instead.
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The w83627ehf driver changes the fan clock divider automatically when
a new min fan speed is set. It is supposed to preserve the fan speed
reading while doing so, bug doesn't really. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
On ia64, kernel headers define REGION_OFFSET so we can't use that.
Reported by Andrew Morton.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users have been complaining about the w83627ehf driver flooding their logs
with debug messages like:
w83627ehf 9191-0a10: Increasing fan 4 clock divider from 64 to 128
or:
w83627ehf 9191-0290: Increasing fan 4 clock divider from 4 to 8
The reason is that we failed to actually write the LSB of the encoded clock
divider value for that fan, causing the next read to report the same old value
again and again.
Additionally, the fan number was improperly reported, making the bug harder to
find.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the detection of fan5 and preserve the bit between the
register writes, because the bit is write only.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Remove Yuan Mu's address
Yuan Mu no longer works at Winbond.
I wish to publicly thank Yuan for his help with Winbond hardware
monitoring chips support during the past 10 months.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w83627ehf: Fix unchecked return status
Fix: check return value from device_create_file()
Fix: call device_remove_file() on error and module unload
Fix: call hwmon_device_register() after device_create_file() to eliminate race
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds long-awaited support for automatic fan modes. Based on
the work of Yuan Mu from Winbond, I finished the support with the great
help of David Hubbard.
Signed-off-by: Yuan Mu <Ymu@Winbond.com.tw>
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-isa: Restore driver owner
Commit 2b48716d1d back in January
2006 was a bit overzealous. It removed .owner from all i2c drivers,
including i2c-isa ones, while they still need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add alarms support for the W83627EHF/EHG hardware monitoring chip.
This is based on an earlier patch from Rudolf Marek.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the voltage measuring support to W83627EHF. The code is based
on the patch provided by Yuan Mu from Winbond.
Signed-off-by: Yuan Mu <Ymu@winbond.com.tw>
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamic sysfs callbacks and array of attributes to reduce the
w83627ehf driver size.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
convert drivers/hwmon/*.c semaphore use to mutexes.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
all affected hwmon drivers were build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the hwmon drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
