Enables the new ixp4xx qmgr and npe drivers in ixp4xx_defconfig.
Sets up the corresponding platform data for the nslu2 and nas100d
boards, and reads the ethernet MAC address from the internal flash.
Tested on both little-endian and big-endian kernels.
Tested-by: Tom King <tom@websb.net>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Michael Westerhof <mwester@dls.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are the only three boards to use the IXP4XX-GPIO-LED driver, and
they can all use the new leds-gpio driver instead with no change in
functionality.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds IXDP425 platform support for two built-in 10/100 Ethernet ports.
This patch will do nothing until the actual Ethernet driver is
also included.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds drivers for IXP4xx hardware Queue Manager and for
Network Processor Engines. Requires patch #4712 (reading/writing
CPU feature (aka fuse) bits).
Posted to linux-arm-kernel on 2 Dec 2007 and revised.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds functions to read and write IXP4xx "feature" (aka "fuse")
bits, containing information about available/enabled CPU features.
The uncompress.h included by boot/compressed/misc.c resides in
a different space than rest of the kernel and thus can't use
asm/hardware.h (including asm/arch/cpu.h - which, in turn, may use
EXPORTed symbol "processor_id").
Posted to linux-arm-kernel on 2 Dec 2007 and revised.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the i2c board info related to the RTC chip on the dsmg600
board to allow it to be found automatically on boot.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the i2c board info related to the RTC chip on the nas100d
board to allow it to be found automatically on boot.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the i2c board info related to the RTC chip on the nslu2 board
to allow it to be found automatically on boot.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Remove the superfluous declaration of ctrl_alt_del().
* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset on the release of the power button, so that
NAS devices which have been set to auto-power-on (by solder
bridging the power button) do not continuously power cycle.
* Remove all superflous constants from dsmg600.h
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset only after the power button has been held down
for at least two seconds. Do the reset on the release of the power
button, so that NAS devices which have been set to auto-power-on (by
solder bridging the power button) do not continuously power cycle.
* Remove all superflous constants from nas100d.h
* Add LED constants to nas100d.h while we're there.
* Update the board LED setup code to use those constants.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the defconfig for the ixp4xx machine in arch/arm/config
taking all the defaults, with the following additions:
1) Enable support for the nslu2, loft, gateway7001, wg302v2,
dsmg600, and gtwx5715 boards.
2) Enable EABI, OABI, HOTPLUG and FW_LOADER.
3) Enable the RTC subsystem, with drivers for the RTC chips on the
nslu2 (x1205) and nas100d/dsmg600 (pcf8563) boards.
4) Enable the LEDS subsystem to support the nslu2, nas100d and
dsmg600 boards. Enable the ixp4xx beeper driver.
5) Enable the USB subsystem, USB host driver support and USB mass
storage support (required for boot disk on nslu2 board).
6) Enable the ATA subsystem, with drivers for the nas100d/dsmg600
(pata_artop) and avila (ixp4xx_cf) boards.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
A HOWTO that hasn't been updated for half a dozen years no longer
"contains valuable information about which PCI hardware does work under
Linux and which doesn't".
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use gpio_vbus instead of udc_is_connected for udc on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The break_lock data structure and code for spinlocks is quite nasty.
Not only does it double the size of a spinlock but it changes locking to
a potentially less optimal trylock.
Put all of that under CONFIG_GENERIC_LOCKBREAK, and introduce a
__raw_spin_is_contended that uses the lock data itself to determine whether
there are waiters on the lock, to be used if CONFIG_GENERIC_LOCKBREAK is
not set.
Rename need_lockbreak to spin_needbreak, make it use spin_is_contended to
decouple it from the spinlock implementation, and make it typesafe (rwlocks
do not have any need_lockbreak sites -- why do they even get bloated up
with that break_lock then?).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
"make dep" is no longer required in kernel 2.6, but was still mentioned
in some places.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the supported clocks on the S3C2440 and S3C2442 to
better represent the DVS state which controls whether FCLK or HCLK
is fed to the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge together the bits of the S3C2440 and S3C2442 clock code
that can be.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the reverse of s3c2410_gpio_getirq to convert
a IRQ number into a GPIO pin number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the S3C2412 fclk is derived from msysclk, not straight from
the MPLL output. Set clk_f.parent appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The msysclk clock was checking for the wrong PLL for the
parent in s3c2412_setparent_msysclk(), trying the UPLL instead
of the MPLL output.
Also ensure the mpll and fclks are at the same rate at init time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the channel parameter to s3c2410_dma_ctrl() in s3c2410_dma_enqueue()
if the S3C2410_DMAF_AUTOSTART is set on the channel.
Spotted by Steven Ryu at Samsung.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c2410_dma_request() function should return the channel allocated
instead of zero for success.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The core resume code may have caused glitches in the GPIO when
restoring the GPIO state due to the order in which the GPIO registers
were being written.
Change the restore process take into account the state of the
GPIOs on resume and the state the system wants to restore them to.
See the code comments in the patch for more details of the process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the call s3c2410_gpio_getpull() to return the
current state of the pin's pull-up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.
Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: Ben Dooks <ben-linux@flfuf.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.
This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep
configuration of the GPIO blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the S3C2412 to indicate the current clock connected to
the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add checks for clk_set_rate() and ensure that we do not allow set_rate
to be called for a clock that does not have it defined. Add default
methods for fclk, hclk, pclk and mpll.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check if the sleep command returns due to a pending interrupt
in the standby unit. If this happens, try and ack the IRQ
before re-trying the resume.
It is currently unclear whether the resume can be backed out
of at this stage as this could cause a problem with level
based interrupts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS and SDI register hw_addr definitions are
incorrect in the DMA map for the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 GPIO is similar enough to the S3C2410 that
it can use it as a base for GPIO functionality.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have a default display set to 4, when we only have
three registered displays. Fix this argument (a seperate
patch has been generated to ensure that the LCD driver
takes notice of this bug)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix all those PXA mci_init functions which return -1 rather than
propagating the error code to the higher levels. Remove the silly
set_irq_type() calls as well - use the flags for request_irq()
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds baseboard support for the phyCORE-PXA270 development
kit (aka PCM-990).
This example shows how to use some phyCORE-PXA270 CPU module features
on a baseboard in a standard manner. It could be used as a starting
point for custom baseboard development.
V2:
After comments by Eric Miao:
- IRQ chained handler fixed
- video/graphic support moved to separate patch
- ifdef/endif hell reduced ;-)
V3:
After comments by Russell King
- initialise the mmci platform data statically
V4:
After comments by Russell King
- wrong return value in pcm990_mci_init() fixed
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
