When a USB device is put into suspend mode, the current drawn from VBUS
has to be less than 500 uA. Some transceivers need to be put into a
special power-saving mode to accomplish this, and won't have a separate
OTG driver handling that.
This adds a suspend method to the "otg_transceiver" struct -- misnamed,
it's not only for OTG -- and calls it from the OMAP UDC driver.
Signed-off-by: Juha Yrj?l? <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as581) changes the assignments to hcd->state in the uhci-hcd
driver. It fixes part of bugzilla entry #5227. The problem was revealed
by David's large suite of USB suspend/resume patches; this patch should go
to Linus at the same time those do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change to make DMA work two bytes at a time omitted an important
tweak that affects the file_storage gadget: it needs to recognize when
the host writes an odd number of bytes. (The network layer ignores
such extra bytes.)
This patch resolves that issue by checking the relevant bit and adjusting
the rx byte count, so that for example a legal 13 byte request doesn't
morph into an illegal 14 byte one any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just a small patch that fixes a small parameter validation bug.
drivers/usb/input/map_to_7segment.h:
This patch fixes the broken parameter validation in the char to seg7
conversion. This could cause out-of-bounds memory references.
MAINTAINERS:
Yealink maintainer info now in sorted order.
Documentation/input/yealink.txt:
Added a Q&A section that answers some common questions.
Signed-off-by: Henk <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
006491df1a13f85ad245d1039dfdf20e49c394fd
The uhci-hcd driver is fairly lax about the way it handles isochronous
transfers. This patch (as579) improves it in three respects:
TDs for a new URB aren't added to the schedule until all of
them have been allocated. This way there's no risk of the
controller executing some of them when an allocation fails.
TDs for an unlinked URB are removed from the schedule as soon
as the URB is unlinked, rather than waiting until the URB is
given back. This way there's no risk of the controller still
executing a TD after the URB completes.
The urb->error_count values are now reported correctly.
Although since they aren't used in any drivers except for
debug messages in the system log, probably nobody cares.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code. It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume. These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.
It also takes David's advice about removing the layer of bus glue, where
those methods are called. And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as574) updates the PCI BIOS usb-handoff code for UHCI
controllers, making it work like the reset routines in uhci-hcd. This
allows uhci-hcd to drop its own routines in favor of the new ones
(code-sharing).
Once the patch is merged we can turn the usb-handoff option on
permanently, as far as UHCI is concerned. OHCI and EHCI may still have
some issues.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as575) fixes an unlikely race in the g_file_storage driver.
The problem can occur only when the driver is unbound before its
initialization routine has finished.
I also took the opportunity to replace kmalloc/memset with kzalloc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds US_FL_FIX_CAPACITY for yet _another_ entire block of Apple
productIds. They really can't seem to get this right. This one is for
the iPod Nano. Reported by Tyson Vinson <lornoss@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/unusual_devs.h | 10 ++++++++++
1 file changed, 10 insertions(+)
This patch adds the US_FL_IGNORE_RESIDUE flag for the TrekStor i.Beat
Joy 2.0. Original version of this patch was sent by Stefan Werner
<dustbln@gmx.de> with test/rediff/etc. by me.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/unusual_devs.h | 7 +++++++
1 file changed, 7 insertions(+)
A while ago, Matthew Dharm wrote:
> Looks good. Tho, I would like to see a future patch to do two things:
> 1) Change comments from C++ style to C-style
> 2) Make sure we're naming consistently everywhere SCM, USBAT,
> USBAT-02 (most noticably needing fixing is the string used at
> transport-selection time, but a sweep of all uses to be consistent
> would be in order).
Sorry for the long delay, here is a patch to address this. I also clarified
some ATA/ATAPI wording + function names.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/shuttle_usbat.c | 306 ++++++++++++++++++++----------------
drivers/usb/storage/shuttle_usbat.h | 66 +++----
drivers/usb/storage/transport.h | 2
drivers/usb/storage/unusual_devs.h | 10 -
drivers/usb/storage/usb.c | 4
5 files changed, 213 insertions(+), 175 deletions(-)
There appears to be one more case where the HP8200 CD writer devices are
detected as flash readers - when the USB cable is replugged after use, with
the power cable still connected.
Oddly enough, the identify device command appears to 'fall through' when the
devices are in this state, the status register reading exactly the same opcode
as the command (0xA1) that was just executed.
I think it's safe to label this behaviour as specific to HP8200 devices, I
can't get the flash devices to respond like this.
This patch should solve the last of the HP8200 issues which have cropped up
recently.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/shuttle_usbat.c | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
the following patch splits the NOTE: in the Device Drivers->USB submenu of
Kconfig thus making the whole of it readable on 600x800 terminals.
(Otherwise, the line was too big and disappeared into nowhere.)
Signed-off-by: Borislav Petkov <petkov@uni-muenster.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/storage/Kconfig | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
This one is a tiny patch adding one more device to the list. Please
apply. :)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/net/pegasus.h | 2 ++
1 file changed, 2 insertions(+)
We would like to add a PID for the Pyramid Appliance Display, which works
on USB via FTDI_SIO.
Signed-off-by: Thomas Riewe <thomasr@pyramid.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/ftdi_sio.c | 1 +
drivers/usb/serial/ftdi_sio.h | 3 +++
2 files changed, 4 insertions(+)
Also has the nice benefit of making sparc alignment issues go away.
Thanks to David Miller for pointing out the problems here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 22 ++++++++++++----------
drivers/usb/core/hub.h | 2 +-
2 files changed, 13 insertions(+), 11 deletions(-)
This patch (as566) converts the File-Storage gadget over to the kthread
API. The new code doesn't use kthread_stop because the control thread
needs to terminate asynchronously when it receives a signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/gadget/file_storage.c | 32 +++++++++++++-------------------
1 file changed, 13 insertions(+), 19 deletions(-)
This patch (as570) changes some comments in the uhci-hcd header file and
removes an unused declaration (something I forgot to erase in an earlier
patch).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/uhci-hcd.h | 91 +++++++++++++++++++++++---------------------
1 file changed, 49 insertions(+), 42 deletions(-)
Because there is no bulk_interrupt_message() routine and no
USBDEVFS_INTERRUPT ioctl, people have been forced to abuse the
usb_bulk_message() routine and USBDEVFS_BULK by using them for interrupt
transfers as well as bulk transfers.
This patch (as567) formalizes this practice and adds code to
usb_bulk_message() for detecting when the target is really an interrupt
endpoint. If it is, the routine submits an interrupt URB (using the
default interval) instead of a bulk URB. In theory this should help HCDs
that don't like it when people try to mix transfer types, queuing both
periodic and non-periodic types for the same endpoint.
Not fully tested -- I don't have any programs that use USBDEVFS_BULK for
interrupt transfers -- but it compiles okay and normal bulk messages work
as well as before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/message.c | 24 ++++++++++++++++++++----
1 file changed, 20 insertions(+), 4 deletions(-)
Reject URBs to _all_ devices when their host controllers are suspended;
even root hub registers will be unavailable. Also, don't reject urbs
to root hubs in other cases; the only upstream link is through that
controller (on PCI or whatever SOC bus is in use).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd.c | 28 ++++++++++++----------------
drivers/usb/core/urb.c | 3 ++-
2 files changed, 14 insertions(+), 17 deletions(-)
The way we're looking at USB suspend lately doesn't expect drivers to
call usb_suspend_device() or usb_resume_device() directly; that'll
be implicit when no interfaces are in use.
This patch removes those APIs from visibility outside usbcore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
drivers/usb/core/hub.c | 12 ++++--------
drivers/usb/core/usb.h | 4 ++++
include/linux/usb.h | 5 -----
3 files changed, 8 insertions(+), 13 deletions(-)
This makes the isp116x driver stop using usb_suspend_device() and
usb_resume_device() ... usbcore now calls to the root hub methods,
removing the need for this. It also switches from keventd to khubd
for remote wakeup. (Compile tested.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/isp116x-hcd.c | 29 ++++-------------------------
drivers/usb/host/isp116x.h | 1 -
2 files changed, 4 insertions(+), 26 deletions(-)
The PCI "early usb handoff" quirk logic didn't work like "ohci-hcd" ...
This patch makes it do so by:
- Resetting the controller after kicking BIOS off, matching the
normal "chip in hardware reset" startup mode;
- Reporting any BIOS that borks this simple handoff; it's likely
got a few other surprises for us too.
- Ignoring that handoff on HPPA;
The diagnostic string is mostly shared with EHCI, saving a few bytes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/pci-quirks.c | 22 ++++++++++++++++++----
1 file changed, 18 insertions(+), 4 deletions(-)
This simplifies the OHCI root hub suspend logic:
- Uses new usbcore root hub calls to make autosuspend work again:
* Uses a newish usbcore root hub wakeup mechanism,
making requests to khubd not keventd.
* Uses an even newer sibling suspend hook.
- Expect someone always made usbcore call ohci_hub_suspend() before bus
glue fires; and that ohci_hub_resume() is only called after that bus
glue ran. Previously, only CONFIG_USB_SUSPEND promised those things.
(Includes updates to PCI and OMAP bus glue.)
- Handle a not-noticed-before special case during resume from one of
the swsusp snapshots when using "usb-handoff": the controller isn't
left in RESET state. (A bug to fix in the usb-handoff code...)
Also cleans up a minor debug printk glitch, and switches an mdelay over
to an msleep (how did that stick around for so long?).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ohci-dbg.c | 4 ----
drivers/usb/host/ohci-hcd.c | 2 +-
drivers/usb/host/ohci-hub.c | 42 ++++++++++++------------------------------
drivers/usb/host/ohci-mem.c | 1 -
drivers/usb/host/ohci-omap.c | 36 ++++++++++++------------------------
drivers/usb/host/ohci-pci.c | 40 ++++++++--------------------------------
drivers/usb/host/ohci.h | 1 -
7 files changed, 33 insertions(+), 93 deletions(-)
This updates the PCI glue to address the new and simplified usbcore suspend
semantics, where CONFIG_USB_SUSPEND becomes irrelevant to HCDs because
hcd->hub_suspend() will always be called.
- Removes now-unneeded recursion support
- Go back to ignoring faults reported by the wakeup calls; we expect them
to fail sometimes, and that's just fine.
The PCI HCDs will need simple changes to catch up to this, like being able
to ignore the setting of CONFIG_USB_SUSPEND.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd-pci.c | 106 +++++++++++++++++++++------------------------
drivers/usb/core/hcd.h | 6 +-
2 files changed, 53 insertions(+), 59 deletions(-)
This patch associates hub suspend and resume logic (including for root hubs)
with CONFIG_PM -- instead of CONFIG_USB_SUSPEND as before -- thereby unifying
two troublesome versions of suspend logic into just one. It'll be easier to
keep things right from now on.
- Now usbcore _always_ calls hcd->hub_suspend as needed, instead of
only when USB_SUSPEND is enabled:
* Those root hub methods are now called from hub suspend/resume;
no more skipping between layers during device suspend/resume;
* It now handles cases allowed by sysfs or autosuspended root hubs,
by forcing the hub interface to resume too.
- All devices, including virtual root hubs, now get the same treatment
on their resume paths ... including re-activating all their interfaces.
Plus it gets rid of those stub copies of usb_{suspend,resume}_device(), and
updates the Kconfig to match the new definition of USB_SUSPEND: it provides
(a) selective suspend, downstream from hubs; and (b) remote wakeup, upstream
from any device configuration which supports it.
This calls for minor followup patches for most HCDs (and their PCI glue).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/Kconfig | 11 ++-
drivers/usb/core/hub.c | 163 +++++++++++++++++++++++++----------------------
2 files changed, 97 insertions(+), 77 deletions(-)
This patch collects various small updates related to root hubs, to shrink
later patches which build on them.
- For root hub suspend/resume support:
* Make the existing usb_hcd_resume_root_hub() routine respect pmcore
locking, exporting and using the dpm_runtime_resume() method.
* Add a new usb_hcd_suspend_root_hub() to pair with that routine.
(Essential to make OHCI autosuspend behave again...)
* HC_SUSPENDED by itself only refers to the root hub's downstream ports.
So let HCDs see root hub URBs unless the parent device is suspended.
- Remove an assertion we no longer need (and now, also don't want).
- Generic suspend/resume updates to work better with swsusp.
* Ignore the FREEZE vs SUSPEND distinction for hardware; trying to
use it breaks the swsusp snapshots it's supposed to help (sigh).
* On resume, mark devices as resumed right away, but then
do nothing else if the device is marked NOTATTACHED.
These changes shouldn't be very noticable by themselves.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/base/power/runtime.c | 1
drivers/usb/core/hcd.c | 64 ++++++++++++++++++++++++++++++++++++++-----
drivers/usb/core/hcd.h | 1
drivers/usb/core/hub.c | 45 ++++++++++++++++++++++++------
drivers/usb/core/usb.c | 20 +++++++++----
drivers/usb/core/usb.h | 1
6 files changed, 111 insertions(+), 21 deletions(-)
This cleans up a small recent FIXME, ensuring that all the HCDs provide
root hub suspend/resume methods. It also wraps the calls to those root
suspend routines just like on the PCI "USB_SUSPEND not defined" cases,
so non-PCI bus glue won't be as tempted to behave very differently.
Several of the SOC based OHCI drivers forgot to list those methods;
the patch also adds those missing declarations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd.c | 42 +++++++++++++++++++++++++---------------
drivers/usb/host/ohci-au1xxx.c | 5 ++++
drivers/usb/host/ohci-lh7a404.c | 5 ++++
drivers/usb/host/ohci-pxa27x.c | 1
drivers/usb/host/ohci-s3c2410.c | 1
drivers/usb/host/ohci-sa1111.c | 1
6 files changed, 40 insertions(+), 15 deletions(-)
This splits BIOS and PCI specific support out of ehci-hcd.c into
ehci-pci.c. It follows the model already used in the OHCI driver
so support for non-PCI EHCI controllers can be more easily added.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ehci-hcd.c | 543 ++++++--------------------------------------
drivers/usb/host/ehci-pci.c | 414 +++++++++++++++++++++++++++++++++
drivers/usb/host/ehci.h | 1
3 files changed, 492 insertions(+), 466 deletions(-)
This patch (as563) splits the physical and logical framelist arrays in
uhci-hcd into two separate pieces. This will allow slightly better memory
utilization, since each piece is no larger than a single page whereas
before the whole thing was a little bigger than two pages. It also allows
the logical array to be allocated in non-DMA-coherent memory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as562) removes from the uhci-hcd driver a few unused fields
and some unnecessary tests against NULL and assignments to NULL. In fact
it wasn't until fairly recently that the tests became unnecessary.
Before last winter it was possible that the driver's stop() routine would
get called even if the start() routine returned an error, but now that
can't happen. Hence there's no longer any need to check for partial
initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simplifies some of the PM-related #ifdeffing by recognizing
that USB_SUSPEND depends on PM. Also, OHCI drivers were often
testing for USB_SUSPEND when they should have tested just PM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hcd.c | 2 ++
drivers/usb/host/ohci-hcd.c | 2 +-
drivers/usb/host/ohci-hub.c | 4 ++--
drivers/usb/host/ohci-omap.c | 2 +-
drivers/usb/host/ohci-pci.c | 2 +-
drivers/usb/host/ohci-ppc-soc.c | 4 ++--
drivers/usb/host/ohci-pxa27x.c | 2 +-
drivers/usb/host/ohci-s3c2410.c | 3 +--
drivers/usb/host/ohci-sa1111.c | 2 +-
9 files changed, 12 insertions(+), 11 deletions(-)
This gets rid of some inconsistently duplicated logic to resume interfaces.
Similar code was in both finish_port_resume() and in usb_generic_resume().
Now there is just one copy of that code, accessed regardless of whether
CONFIG_USB_SUSPEND is enabled. Fault handling is also more consistent.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the extra usb_suspend_device() parameter. The original
reason to pass that parameter was so that this routine could suspend any
active children. A previous patch removed that functionality ... leaving
no reason to pass the parameter. A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.
On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend. It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 34 +++++++++++++++++++++-------------
drivers/usb/core/usb.c | 23 +++++++++++++++++++++--
drivers/usb/host/ehci-hcd.c | 2 +-
drivers/usb/host/isp116x-hcd.c | 2 +-
drivers/usb/host/ohci-pci.c | 2 +-
include/linux/usb.h | 2 +-
6 files changed, 46 insertions(+), 19 deletions(-)
This patch removes some recursion in the CONFIG_USB_SUSPEND logic, which
suspended children (of devices or hubs) that weren't already suspended.
When it sees such cases, suspend now just fails cleanly.
That logic was not needed during system-wide sleep state transitions; and
given the current notions of how to manage selective suspend transitions,
we don't want it there either. Where it was particularly handy was coping
with various limitations of the sysfs "echo -n N > power/state" support.
(These include assuming that "N" is always meaningful to the driver; and
that drivers can only transition to state N from state zero.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the handling of power state for USB interfaces.
- Formalizes an existing invariant: interface "power state" is a boolean:
ON when I/O is allowed, and FREEZE otherwise. It does so by defining
some inlined helpers, then using them.
- Adds a useful invariant: the only interfaces marked active are those
bound to non-suspended drivers. Later patches build on this invariant.
- Simplifies the interface driver API (and removes some error paths) by
removing the requirement that they record power state changes during
suspend and resume callbacks. Now usbcore does that.
A few drivers were simplified to address that last change.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/hub.c | 33 +++++++++------------
drivers/usb/core/message.c | 1
drivers/usb/core/usb.c | 65 +++++++++++++++++++++++++++++++++----------
drivers/usb/core/usb.h | 18 +++++++++++
drivers/usb/input/hid-core.c | 2 -
drivers/usb/misc/usbtest.c | 10 ------
drivers/usb/net/pegasus.c | 2 -
drivers/usb/net/usbnet.c | 2 -
8 files changed, 85 insertions(+), 48 deletions(-)
This moves the PCI quirk handling for USB host controllers from the
PCI directory to the USB directory. Follow-on patches will need to:
(a) merge these copies with the originals in the HCD reset methods.
they don't wholly agree, despite doing the very same thing; and
(b) eventually change it so "usb-handoff" is the default, to help
get more robust USB/BIOS/input/... interactions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/Makefile | 2
drivers/pci/quirks.c | 253 ---------------------------------------
drivers/usb/Makefile | 1
drivers/usb/host/Makefile | 5
drivers/usb/host/pci-quirks.c | 272 ++++++++++++++++++++++++++++++++++++++++++
5 files changed, 280 insertions(+), 253 deletions(-)
This patch adds endpoint information for both devices and interfaces to
sysfs. Previously it was only possible to get the endpoint information
from usbfs, and never possible to get any information on endpoint 0.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/sysfs.c | 195 ++++++++++++++++++++++++++++++++++++++++++++++-
include/linux/usb.h | 4
2 files changed, 197 insertions(+), 2 deletions(-)
This patch enables direct kernel support for the Artemis
and ATIK astronomical based USB CCD cameras.
Since all communications with this camera are done via an
FTDI 245BM chip, it was only needed to specify the
ProductID and VendorID of all three devices.
In what tests are concerned, data was transfered from and
to the FTDI at the chips Top speed (360KB/s).
Signed-off-by: Rui Santos <rsantos@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/ftdi_sio.c | 3 +++
drivers/usb/serial/ftdi_sio.h | 13 +++++++++++++
2 files changed, 16 insertions(+)
This tweaks the EHCI reboot notifier to also halt the EHCI controller, and
makes that halt code force IRQs off. Both should always have been done.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ehci-hcd.c | 8 ++++++++
1 file changed, 8 insertions(+)
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch teaches "usb_device" about the new driver model wakeup support:
- It updates device wakeup capabilities when entering a configuration
with the WAKEUP attribute;
- During suspend processing it consults the policy bit to see
whether it should enable wakeup for that device. (This resolves
a FIXME to not assume the answer is always "yes"; some devices
lie about supporting remote wakeup.)
Support for root hubs and the HCDs is separate (and more complex).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Ian Campbell
The sparse warning initially surfaced in sound/arm/pxa2xx-ac97.c
because it was using u32 * variables to hold the unsigned long *
register addresses.
I submitted an ALSA patch for this http://thread.gmane.org/gmane.linux.alsa.devel/27804 issue and it was suggested that it might be preferable to change the register
definitions to use u32.
Most other subarches seem to use u32 for their register type, at least
the ones which use a __REG macro (like the PXA) do. Nico indicated in
the thread above that he wouldn't mind this patch.
Changing the type required fixes for opposite warnings in the pxa2xx usb
gadget code but that was the only new warning introduced on defconfig
or lubbock, mainstone and our own PXA255 boards.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During the development of an USB device I found a bug in the handling of
Highspeed HID devices in the kernel.
What happened?
Highspeed HID devices are correctly recognized and enumerated by the
kernel. But even if usbhid kernel module is loaded, no HID reports are
received by the kernel.
The output of the hardware USB analyzer told me that the host doesn't
even poll for interrupt IN transfers (even the "interrupt in" USB
transfer are polled by the host).
After some debugging in hid-core.c I've found the reason.
In case of a highspeed device, the endpoint interval is re-calculated in
driver/usb/input/hid-core.c:
line 1669:
/* handle potential highspeed HID correctly */
interval = endpoint->bInterval;
if (dev->speed == USB_SPEED_HIGH)
interval = 1 << (interval - 1);
Basically this calculation is correct (refer to USB 2.0 spec, 9.6.6).
This new calculated value of "interval" is used as input for
usb_fill_int_urb:
line 1685:
usb_fill_int_urb(hid->urbin, dev, pipe, hid->inbuf, 0,
hid_irq_in, hid, interval);
Unfortunately the same calculation as above is done a second time in
usb_fill_int_urb in the file include/linux/usb.h:
line 933:
if (dev->speed == USB_SPEED_HIGH)
urb->interval = 1 << (interval - 1);
else
urb->interval = interval;
This means, that if the endpoint descriptor (of a high speed device)
specifies e.g. bInterval = 7, the urb->interval gets the value:
hid-core.c: interval = 1 << (7-1) = 0x40 = 64
urb->interval = 1 << (interval -1) = 1 << (63) = integer overflow
Because of this the value of urb->interval is sometimes negative and is
rejected in core/urb.c:
line 353:
/* too small? */
if (urb->interval <= 0)
return -EINVAL;
The conclusion is, that the recalculaton of the interval (which is
necessary for highspeed) should not be made twice, because this is
simply wrong. ;-)
Re-calculation in usb_fill_int_urb makes more sense, because it is the
most general approach. So it would make sense to remove it from
hid-core.c.
Because in hid-core.c the interval variable is only used for calling
usb_fill_int_urb, it is no problem to remove the highspeed
re-calculation in this file.
Signed-off-by: Christian Krause <chkr@plauener.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increased use of scatter-gather by usb-storage driver after 2.6.13 has
exposed a buggy codepath in isp116x-hcd, which was probably never
visited before: bug happened only for those urbs, for which
URB_SHORT_NOT_OK was set AND short transfer occurred.
The fix attached was tested in 2 ways: (a) it fixed failing
initialization of a flash drive with an embedded hub; (b) the fix was
tested with 'usbtest' against a modified g_zero driver (on top of
net2280), which generated short bulk IN transfers of various lengths
including multiples and non-multiples of max_packet_length.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kernel version 2.6.13 introduced a regression in the generic USB
serial converter driver (usbserial.o, drivers/usb/serial/generic.c).
The bug manifests, as far as I can tell, whenever you attempt to write
to the device -- the write will never complete (write() returns 0, or
blocks).
Signed-off-by: Randall Nortman <oss@wonderclown.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All the same issues - we can't just save the pointer to the thread, we
must save the pid/uid/euid combination.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a process issues an URB from userspace and (starts to) terminate
before the URB comes back, we run into the issue described above. This
is because the urb saves a pointer to "current" when it is posted to the
device, but there's no guarantee that this pointer is still valid
afterwards.
In fact, there are three separate issues:
1) the pointer to "current" can become invalid, since the task could be
completely gone when the URB completion comes back from the device.
2) Even if the saved task pointer is still pointing to a valid task_struct,
task_struct->sighand could have gone meanwhile.
3) Even if the process is perfectly fine, permissions may have changed,
and we can no longer send it a signal.
So what we do instead, is to save the PID and uid's of the process, and
introduce a new kill_proc_info_as_uid() function.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
[ Fixed up types and added symbol exports ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the free_irq() in USB suspend breaks resume on some setups where USB
(ohci/ehci) shares the interrupt with an other device.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of create_proc_dir_entry() calls creating directories had crept
in since the last sweep; converted to proc_mkdir().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since asm/hardware.h's only reason for existing is to include
asm/arch/hardware.h, it's completely pointless to include both.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
USB: Add device id's for Novatel Wireless CDMA wireless PC card.
The Novatel CDMA card behaves the same as the AirPrime by providing
a USB serial port.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The card sometimes sends >2000 bytes in one single chunk. Ouch.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Addresses some small bugs in the pegasus ethernet-over-USB driver.
Specifically, malformed long packets from the adapter could cause a kernel
panic; the interrupt interval calculation was inappropriate for high-speed
devices; the return code from read_mii_word was tested incorrectly; and
failure to unlink outstanding URBs before freeing them could lead to kernel
panics when unloading the driver.
Signed-off-by: Kevin Vigor <kevin@realmsys.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Three minor sl811-hcd fixes:
- Elminate memory leak on one (rare) disable/shutdown path.
- For periodic transfers that don't need to be scheduled, update
urb->start_frame to represent the transfer phase correctly.
- Report the (single) port as removable, by default.
Since no drivers yet use start_frame or that part of the hub descriptor,
only that leak is likely to ever matter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/host/sl811-hcd.c | 16 ++++++++++++++--
1 file changed, 14 insertions(+), 2 deletions(-)
This patch fixes several types in the PXA25x udc driver and hence fixes
several compiler warnings.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm using a 2 port USB RS232 dongle to connect to a serial-IR cradle for
a bar code reader). Detecting the baudrate of the serial-IR involves
keeping DTR low while changing baudrate.
This works using normal 16550A serial ports as well as the FTDI driver
version 1.4.0 (Linux 2.6.8) but stopped working with the change to
"ensure RTS and DTR are raised when changing baudrate" introduced in
version 1.4.1 (Linux 2.6.9).
The attached patch fixes this, so RTS and DTR is only raised when
changing baudrate iff the previous baudrate was B0.
Signed-off-by: Peter Favrholdt <pfavr@how.dk>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added support for HUAWEI E600 and Audiovox AirCard
User reports say that these devices work without driver modification.
Signed-off-by: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add the helper and use it instead of open coding the klist_node_attached() check
(which is a layering violation IMHO)
idea by Alan Stern.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: I messed up the baud_base for custom baud rate support in
2.6.13. The attached one-liner patch fixes it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern sent me this patch. It goes on top of the patch the adds
mon_dmapeek:
http://ftp.kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/gregkh-04-usb/usb-usbmon-dma-areas.patch
Please be warned about ordering requirements or the build may fail.
Actually, mon_dmapeek is generic enough to support SETUP packets too.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the long standing schedule with interrupts off problem
of the uss720 driver. The problem is caused by the parport layer calling
the save and restore methods within a write_lock_irqsave guarded region.
The fix is to issue the control transaction requests required by save
and restore asynchronously.
Signed-off-by: Thomas Sailer, <sailer@ife.ee.ethz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern wrote:
> If the device sometimes reports the correct values, then you should
> include NEED_OVERRIDE flag to prevent messages about unnecessary
> overrides showing up in the system log. Also, if bInterfaceSubclass
> is correct and only bInterfaceProtocol is wrong, then the entry should
> say US_SC_DEVICE instead of US_SC_SCSI.
Fair points, thanks.
When connected over USB2, this device reports a nonsense
bInterfaceProtocol value 6 and doesn't work with usb-storage. When
connected over USB1, the device reports the correct bInterfaceProtocol
value 0x50 (bulk) and works with no problems.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds entries for several USB floppies that need
the US_FL_SINGLE_LUN flag. These were reported by
Sebastian Kapfer <sebastian_kapfer@gmx.net> and Olaf Hering
<olh@suse.de>, with rediffing and cleaning from me.
Reported-by: Sebastian Kapfer <sebastian_kapfer@gmx.net>
Reported-by: Olaf Hering <olh@suse.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The stick replies to the door lock commands with a check condition (e.g.
FAIL status in a normal bulk CSW), but the subsequent REQUEST SENSE
returns all-zero sense. The situation is documented in our Bugzilla,
including usbmon traces.
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=162559
The error is purely cosmetic, data integrity is not in danger.
But I thought we might as well do it. It looks nicer that way.
I discussed this with Phil and he told me to submit directly.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is patch as550 from Alan Stern.
Apparently someone changed the SCSI core so that it no longer holds the
host lock when doing a device or bus reset. usb-storage was updated at
the time, but the change was done carelessly. Some of the code depends
on that lock being held.
This patch reintroduces the host lock where needed and tries to clarify
the comments explaining why the lock is necessary. It also moves the
code that clears the TIMED_OUT and ABORTING bitflags so that it executes
as soon as the timed-out command has completed (and while the host lock
is held).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This appears to help some folk, please merge.
This patch relaxes reset timings. There are some reports that it
helps make enumeration work better on some high speed devices.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID and vendor ID for a Nokia CA-42 USB cable
to the list of devices handled by the pl2303 driver. The patch is
against 2.6.13.
Signed-off-by: Robert Spanton <rds204@zepler.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that it's in use on other boards, a bug in the original code needs fixing.
There is no need for the PXA27x OHCI to set usb power during init, since
the hub driver in usbcore handles that. Those platform-specific power
control functions are also incorrect, and should therefore be removed.
Add a check to clear the OTG pin hold bit until such times OTG is
properly implemented.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some OHCI implementations have differences in the way the NDP register
(in roothub_a) reports the number of ports present. This patch allows the
platform specific code to optionally supply the number of ports. The
driver just reads the value at init (if not supplied) instead of reading
it every time its needed (except for an AMD756 bug workaround).
It also sets the value correctly for the ARM pxa27x architecture.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evidently there are some boards which care a lot about this, but
as a rule it's been hard to notice.
OHCI_INTR_RD wasn't always cleared in the ohci irq handler. On some
systems this means certain remote wakeup scenarios could seem to hang
(in an interrupt storm, RD never clearing).
From: "William Morrow" <William.Morrow@amd.com>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch fixes an "Invalid argument" error returned by a write to an
endpoint-file after reopening it in the gadgetfs module in the kernel
2.6.12.
This was testet only with dummy_hcd module!
Signed-off-by: Pavol Kurina <kurina@gmx.net>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Routine cases like handoff-to-companion shouldn't trigger diagnostics.
This gets rid of some recently added log spamming. It's routine for
hub_port_wait_reset() to return -ENOTCONN to indicate handoff from
highspeed hubs to companions, so an error message is incorrect.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NVidia reports (via Mark Overby) that some of their EHCI controllers
don't like certain data structure addresses beyond the 2GB mark.
He provided an earlier version of this patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One change may improve some S1 or S3 resume cases, and the other
seems mostly to explain some strange state "lsusb" would show.
Two fixes:
- On resume, don't think about resuming any unpowered port, or
resetting any port with OWNER set to the OHCI/UHCI companion.
This will make some S1 and S3 resume scenarios work better.
- PORT_CSC was not being cleared correctly in ehci_hub_status_data.
This was visible at least through current versions of "lsusb",
and might have caused some other hub related strangeness.
The fix addresses all three write-to-clear bits, using the same
approach that UHCI happens to use: a mask of bits that are
cleared in most writes to that port status register.
Original patch seems to have been from from William.Morrow@amd.com
and this version (from David) finishes the write-to-clear changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Three new device IDs for CP2101 USB to UART Bridge
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as558) removes from the UHCI driver a kernel timer used for
checking Full Speed Bandwidth Reclamation (FSBR). The checking can be
done during normal root-hub polling; it doesn't need a separate timer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as549) introduces two small changes in the HCD glue layer.
The first simply removes a redundant test. The second allows root-hub
polling to continue for a single iteration after a host controller dies;
this is needed for the patch that follows.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.
This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
* appletouch is a full kernel driver, no userspace program is necessary
* appletouch can be interfaced with the synaptics X11 driver[2], in order
to have touchpad acceleration, scrolling, two/three finger tap, etc.
This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.
Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
here is a new and extended version of the sisusbvga (previously: sisusb)
driver. The patch is against 2.6.13 and updates the driver to version 0.0.8.
Additions include complete VGA/EGA text console support and a build-in
display mode infrastructure for userland applications that don't know
about the graphics internals.
Fixes include some BE/LE issues and a get/put_dev bug in the previous
version.
Other changes include a change of the module name from "sisusb" to
"sisusbvga". The previous one was too generic IMHO.
Please note that the patch also affects the Makefile in
drivers/video/console as the driver requires the VGA 8x16 font in case
the text console part is selected.
Heavily tested, as usual. Please apply.
One thing though: I already prepared for removal of the "mode" field and
the changed "name" field in the usb_class_driver structure. This will
perhaps need some refinement depending on whether you/Linus merge the
respective core changes before or after 2.6.14.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does a full cleanup of 'NULL checks before vfree', and a partial
cleanup of calls to kfree for all of drivers/ - the kfree bit is partial in
that I only did the files that also had vfree calls in them. The patch
also gets rid of some redundant (void *) casts of pointers being passed to
[vk]free, and a some tiny whitespace corrections also crept in.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch aggregates all modifications in the -mm tree and adds
complete ringtone support.
The following features are supported:
- keyboard full support
- LCD full support
- LED full support
- dialtone full support
- ringtone full support
- audio playback via generic usb audio diver
- audio record via generic usb audio diver
For driver documentation see: Documentation/input/yealink.txt
For vendor documentation see: http://yealink.com
Signed-off-by: Henk <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As sugested by Alan Stern here are a few code cleanups for onetouch.c:
-Check number of endpoints before directly referencing intf->endpoint[2]
-Use defined constants instead of magic numbers
-Revmove the non-ascii characters from copyright notice
-Make registration and deregistration messages more similar
Signed-off-by: Nick Sillik <n.sillik@temple.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This code looks at urb->transfer_dma, maps the page and takes the data.
I am looking for volunteers to contribute architectures other than i386
or to develop an architecure-neutral API for it (or point me that it
was done already).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the field tt_usecs to ehci_qh and ehci_iso_stream, and sets it
appropriately when setting them up as periodic endpoints. It records
the transation translator's think_time (added in last patch) plus the
downstream (i.e. low or full speed) bustime of the transfer associated
with each interrupt or iso frame, as calculated by usb_calc_bus_time.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds think_time to the usb_tt struct and sets it appropriately
(measured in ns); this can help us implement better split transaction
scheduling.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This wraps up the conversion of the "usbnet" driver structure, by
moving the Prolific PL-2201/2302 minidriver to a module of its own.
It also includes some minor cleanups to the remaining "usbnet" file,
notably removing that long changelog at the top.
Minor historical note: Linux 2.2 first called the driver for
this hardware "plusb".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds host-side RNDIS support to the "usbnet" driver, so Linux can talk
to various devices (often based on WinCE) that otherwise only Windows could
talk to.
Tested with little-endian Linux talking to a Linux-USB Ethernet/RNDIS based
peripheral. This also includes updates from Eddie C. Dost <ecd@brainaid.de>
for big-endian SPARC Linux talking to a Nokia 9500 Communicator.
It's still marked as EXPERIMENTAL because this code is so young. This
ought to let Linux to work with various cable modems that previously
would have been "Windows Only".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes the CDC Ethernet support live in a separate driver module.
This module is a bit special since it exports utility functions
that are reused by the the Zaurus and RNDIS drivers, but it's
not "core" like usbnet itself.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves usbnet support for Zaurus and compatibles into its own module.
Other than exporting a couple of helper functions, this just involved
shuffling some code and updating the comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the GeneSys GL620USB-A support into its own driver file.
It also fixes a "return wrong skb" glitch in the rx unbatching, as
recently reported, and adds some missing byteswaps in the special
"genelink" headers (so it might now work on big-endian Linux).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As with the "cdc_subset" and "asix" drivers, this just moves the net1080
support into its one driver module. In this case there's a small bit of
extra cleanup involved, moving some funky framing logic into the tx_fixup()
routine (resolving a long overdue FIXME).
Minor historical note: "usbnet" started out as "net1080", then got
generalized to make it easier for other network drivers to reuse the
urb queueing and fault management code here.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the ASIX AX8817x driver into its own file, just using
the "usbnet" infrastructure as a utility library.
- As with "cdc_subset" this involved minor Kconfig/kbuild tweaks,
moving code from one file to another, and exporting a few functions.
- This includes updates from Jamie Painter to add (and use) a new hook
to handle the different maximum transfer sizes for rx and tx sides.
- Also from Jamie, some bugfixes:
* MDIO byteorder (to address some PPC media negotiation problems);
* Force alignment at key spots when using ax88772 framing (on some
embedded hardware, the network stack will break otherwise);
* Address some link reset problems.
It also makes this driver use the standard (5 seconds vs half second)
control timeouts used elsewhere in USB; and wraps a few lines before
the 80th column (which previously needed it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch creates the first of several separate "minidriver" modules
for "usbnet". This one handles only the very simplest hardware, which
can be handled almost entirely by the "usbnet" core.
- Move device-specific bits into new "cdc_subset.c" driver,
shrinking "usbnet" by a bunch;
- Export the functions needed to support this minidriver
(with EXPORT_SYMBOL_GPL);
- Update Kconfig and kbuild accordingly.
This one handles about a dozen different device types, with the most
notable ones being Gumstix and most Linux-based PDAs (except Zaurus
running that ancient code from Sharp).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This starts to prepare the core of "usbnet" to know less about various
framing protocols that map Ethernet packets onto USB, so "minidrivers"
can be modules that just plug into the core.
- Remove some framing-specific code that cluttered the core:
* net->hard_header_len records how much space to preallocate;
now drivers that add their own framing (Net1080, GeneLink,
Zaurus, and RNDIS) will have smoother TX paths. Even for
the drivers (Zaurus, Net1080) that need trailers.
* defines new dev->hard_mtu, using this "hardware" limit to
check changes to the link's settable "software" mtu.
* now net->hard_header_len and dev->hard_mtu are set up in the
driver bind() routines, if needed.
- Transaction ID is no longer specific to the Net1080 framing;
RNDIS needs one too.
- Creates a new "usbnet.h" header with declarations that are shared
between the core and what will be separate modules.
- Plus a couple other minor tweaks, like recognizing -ESHUTDOWN
means the keventd work should just shut itself down asap.
The core code is only about 1/3 of this large file. Splitting out the
minidrivers into separate modules (e.g. ones for ASIX adapters,
Zaurii and similar, CDC Ethernet, etc), in later patches, will
improve maintainability and shrink typical runtime footprints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix
drivers/usb/misc/ldusb.c: In function `ld_usb_read':
drivers/usb/misc/ldusb.c:467: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c: In function `ld_usb_write':
drivers/usb/misc/ldusb.c:531: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 5)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 6)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Deprecate the OSS USB drivers.
This patch includes spelling fixes by Lee Revell.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ohci-ppc-soc.c provides for a platform-specific callback mechanism for
when the HC is successfully probed or removed. It turned out that none
of the 3 platforms using it need this facility. Also the required
include/asm-ppc/usb.h has never been accepted. This patch removes the
callback feature and the include of <asm/usb.h>.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid an annoying message that can appear if devices are disconnected
in the middle of a USB scatterlist operation.
Message noted in http://bugzilla.kernel.org/show_bug.cgi?id=4373
(but the real issue there seems to be a SCSI level hang).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use a more correct calculation for highspeed bit times.
http://bugzilla.kernel.org/show_bug.cgi?id=3604
This sort if thing might start to make a difference now that the high
speed periodic scheduler is more complete -- and even getting used.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as556) adds support for unbinding the usb_generic "driver".
That driver only binds to USB devices, as opposed to interfaces, and it
does nothing much besides marking which struct device's go with an
overall USB device plus providing suspend/resume methods. Now that
users can unbind drivers at will using the sysfs "unbind" attribute, we
need a rational way of dealing with USB devices that are no longer under
full control of the USB stack. The patch handles this by unconfiguring
the device, thereby removing all the interfaces and their associated
drivers and children.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as555) modifies the already-awkward
usb_lock_device_for_reset routine in usbcore by adding a timeout. The
whole point of the routine is that the caller wants to acquire some
semaphores in the wrong order; protecting against the possibility of
deadlock by timing out seems only prudent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the port numbering confusion for the S3C24XX platform device
information as reported by Rudy <rudyboy168@gmail.com>
This patch ensurs that the the ports are numbered 0 and 1.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as554) makes the hub driver disconnect any child USB devices
when it is unbound from a hub. Normally this will never happen, but
there are a few oddball ways to unbind the hub driver while leaving the
children intact. For example, the new "unbind" sysfs attribute can be
used for this purpose.
Given that unbinding hubs with children is now safe, the patch also
removes the code that prevented people from doing so using usbfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as553) merely moves some code and deletes an unneeded test in
the hub driver. This is in preparation for the patch that follows.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding flash-device support to the shuttle_usbat driver in 2.6.11
introduced the need to detect which type of device we are dealing with:
CDRW drive, or flash media reader.
The detection routine used turned out to not work for HP8200 CDRW users,
who saw their devices being detected as a flash disk.
This patch (which has been tested on both flash and cdrom) removes some
unnecessary code, moves device detection to much later during
initialization, and introduces a new detection routine which appears to
work.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
29 July 2005, Cambridge, MA:
This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel. Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system. For over a year it hasn't
been used for anything other than printing warning messages."
An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time. As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches. Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."
Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory. "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to. That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."
Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls. His only comment was "Applied, thanks."
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as479b, and has been rediffed. Please note
the order of submission of this latest patch series -- even tho this has
an older original number, it is the last patch I'll be sending today.
This patch changes the reported SCSI revision level to 2 for all
disk-type devices. This is needed in a few cases because the device
reports a level of 3 or higher but then crashes when given a REPORT LUNS
command (for which support is supposed to be mandatory at those levels).
This shouldn't harm us, since it only matters for sparse LUNs and we
have separate ways of coping with that.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is originally from Nick Sillik, and has been rediffed against
the latest tree.
This patch adds usability to the OneTouch Button on Maxtor External USB
Hard Drives. Using an unusual device entry it declares an extra init
function which claims the interrupt endpoint associated with this
button. The button is connected to the input system.
Signed-off-by: Nick Sillik <n.sillik@temple.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as534, and has been re-diffed against the latest
tree.
usb-storage has a small loophole, a window between the time queuecommand
accepts a new command and the time the control thread starts to execute
it. If disconnect is called during that window, the driver won't cancel
the pending command -- we've been relying on the SCSI core to cancel it
for us during host removal. But it's better for usb-storage to cancel
it; this avoids races and reduces reliance on the SCSI core.
Fortunately cancelling these commands is easy to do; the key is to do it
_before_ calling scsi_remove_host.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as533, and has been re-diffed against the
current tree.
Disconnect processing in usb-storage naturally divides into two parts:
one to quiesce the driver (make sure no commands are executing or
queued) and remove the host, and the other to deallocate all the USB and
non-USB resources. This patch creates two subroutines to handle those
two parts. Mostly it's just code movement, but there is one significant
change. If the scsi-scanning thread fails to initialize but the host
has successfully been added, we need to quiesce the driver before
removing the host. After all, it's possible that scanning could have
been initiated from somewhere else, such as userspace -- very low
probability, but it's easily handled by calling the new subroutine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as531 from Alan Stern. It has been rediffed
against the latest tree.
The SCSI people have deprecated the use of scsi_cmnd.serial_number for
anything other than printk. Worse than that, the SCSI core doesn't
always increment the number (when the error handler is running, for
example). So this patch creates a locally-stored value for use in
bulk-only tags. The net result is a simplification, since we no longer
have to save & restore the serial_number value while autosensing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch isp116x-hcd over from root hub polling to interrupt. This change closes
also a race that was present with the old polling scheme: status polling could
happen in a time window, where root hub status bits were not stable.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes support for user-provided platform-specific hardware reset
and clock starting/stopping functions. Hardware reset was needed earlier as
getting the software reset working was tricky due to the lack of documentation.
Recently, a number of people using isp116x have said the software reset is
working for them.
I haven't heard of anybody using the clock starting/stopping.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch sets the isp116x to report overcurrent always per-port.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The isp116x chip will now always be in per-port power switching mode. Remove
conf options to set any other mode.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the power-on-to-power-good-time configuration option for
isp116x-hcd.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This just fixes some gfp flags warnings that joined us recently.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rate-limit usblp printer error status messages.
I unplugged my USB printer and almost instantly got several hundred
of these in my kernel message log:
drivers/usb/class/usblp.c: usblp0: error -19 reading printer status
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an entry in the unusual_devs.h file for a Mitsumi card
reader/floppy combo that uses a VIA chipset. The IGNORE_RESIDUE flag was
needed for the second LUN to operate properly.
Signed-off-by: Mihnea-Costin Grigore <mihnea@zulu.ro>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as551) fixes another little problem recently added to the
USB core. Someone didn't fix the type of the first argument to
unregister_chrdev_region.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a /sys/class/usb_device/ class
where every connected usb-device will show up:
tree /sys/class/usb_device/
/sys/class/usb_device/
|-- usb1.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.0/usb1
|-- usb2.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.1/usb2
...
The presence of the "dev" file lets udev create real device nodes.
kay@pim:~/src/linux-2.6> tree /dev/bus/usb/
/dev/bus/usb/
|-- 1
| `-- 1
|-- 2
| `-- 1
...
udev rule:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usb_device %k", NAME="%c"
(echo $1 | /bin/sed 's/usb\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/')
This makes libusb pick up the real nodes instead of the mounted usbfs:
export USB_DEVFS_PATH=/dev/bus/usb
Background:
All this makes it possible to manage usb devices with udev instead of
the devfs solution. We are currently working on a pam_console/resmgr
replacement driven by udev and a pam-helper. It applies ACL's to device
nodes, which is required for modern desktop functionalty like
"Fast User Switching" or multiple local login support.
New patch with its own major. I've succesfully disabled usbfs and use real
nodes only on my box. With: "export USB_DEVFS_PATH=/dev/bus/usb" libusb picks
up the udev managed nodes instead of reading usbfs files.
This makes udev to provide symlinks for libusb to pick up:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usbdevice %k", SYMLINK="%c"
/sbin/usbdevice:
#!/bin/sh
echo $1 | /bin/sed 's/usbdev\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/'
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To recap: My new G4 powerbook has a bluetooth device that boots up in
what apppears to be a compatability mode - it looks exactly like an HID
keyboard/mouse device.
A special command sequence is sent to switch it into full bluetooth
mode. When this occurs the original HID device vanishes, and a new
(bluetooth HID) USB device appears on the bus with a different product
ID.
The original thread is here:
http://sourceforge.net/mailarchive/message.php?msg_id=12532263
The attached patch adds the device to the hid-core quirks so that
hid-core ignores it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for the ftdi_sio driver adds a bunch of new devices and fixes
an incorrect PID:
o Fix PID for ELV UO100 (the PID was in fact for ELV UR100).
o Add PID ELV UR100 (see above) and ELV ALC 8500 Expert.
o Add a whole bunch of other PIDs for ELV USB devices, commented out for
now as they may be used by other drivers eventually. (Christian Abt
of ELV.de submitted a full list of devices including an indication of
which set of drivers are used by default in the MS Windows world. We
decided to comment out the devices that use FTDI's D2XX Windows
drivers by default.)
o Add PIDs for eight devices from Xsens Technologies BV (submitted in a
patch against 2.6.12.2 by Patrick Riphagen).
o Add PID for Falcom Samba GPRS modem (submitted by Sebastian Schubert).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Support one user specified vendor and product ID via a couple
of new module parameters.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This trivial patch makes pl2303 driver work correctly with pl2303HX chip.
Apparently some bug in HX version of pl2303 makes the chip loose some
transmitted bytes or stop working at all after reception of
USB_REQ_CLEAR_FEATURE mesage. Logs generated by UsbSnoop application reveal
that windows driver does not send this type of messages to the converter.
From: "Dariusz M." <D.Marcinkiewicz@elka.pw.edu.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch centralizes the assignment of bcdDevice numbers for different
gadget controllers. This won't improve the object code at all, but it
does save a lot of repetitive and error-prone source code ... and will
simplify the work of supporting a new controller driver, since most new
gadget drivers will no longer need patches (unless some hardware quirks
limit USB protocol messaging).
Added minor cleanups and identifer hooks for the UDC in the Freescale
iMX series processors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch removes unneeded casts for the following (void *) pointers:
- tty_struct->driver_data
- void *private argument of usb_serial_port_softint()
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reading this driver I noticed some trailing whitespaces and tabs so I
removed them with some 80th column fitting and a few more similar
things.
From: Carlo Perassi <carlo@linux.it>
Signed-off-by: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Carlo Perassi <carlo@linux.it>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver core: link device and all class devices derived from it.
To ease the task of locating class devices derived from a certain
device create symlinks from parent device to its class devices.
Change USB host class device name from usbX to usb_hostX to avoid
conflict when creating aforementioned links.
Tweaked by Greg to have the symlink be "class_name:class_device_name" in
order to prevent duplicate links.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C_DEVNAME and i2c_clientname were introduced in 2.5.68 [1] to help
media/video driver authors who wanted their code to be compatible with
both Linux 2.4 and 2.6. The cause of the incompatibility has gone since
[2], so I think we can get rid of them, as they tend to make the code
harder to read and longer to preprocess/compile for no more benefit.
I'd hope nobody seriously attempts to keep media/video driver compatible
across Linux trees anymore, BTW.
[1] http://marc.theaimsgroup.com/?l=linux-kernel&m=104930186524598&w=2
[2] http://www.linuxhq.com/kernel/v2.6/0-test3/include/linux/i2c.h
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge the algorithm id part (16 upper bits) of the i2c adapters ids
into the definition of the adapters ids directly. After that, we don't
need to OR both ids together for each i2c_adapter structure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more users of i2c_algorithm.id, so we can finally drop
this structure member.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The name member of the i2c_algorithm is never used, although all
drivers conscientiously fill it. We can drop it completely, this
structure doesn't need to have a name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When trying to make the hiddev driver issue several Set_Report control
transfers to a custom device with 2.6.13-rc6, only the first transfer in a
row is carried out, while others immediately following it are silently
dropped.
This happens where hid_submit_report() (in hid-core.c) tests for
HID_CTRL_RUNNING, which seems to be still set because the first transfer is
not finished yet.
As a workaround, inserting a delay between the two calls to
ioctl(HIDIOCSREPORT) in userspace "solves" the problem. The
straightforward fix is to add a call to hid_wait_io() to the implementation
of HIDIOCSREPORT (in hiddev.c), just like for HIDIOCGREPORT. Works fine
for me.
Apparently, this issue has some history:
http://marc.theaimsgroup.com/?l=linux-usb-users&m=111100670105558&w=2
Signed-off-by: Stefan Nickl <Stefan.Nickl@kontron.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The device is a Wireless Security Lock (WSL). The device identifies itself
as a Cypress Ultra Mouse. It is, however, not a mouse at all and as such,
shouldn't be handled as one.
Signed-off-by: Brian Schau <brian@schau.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Map custom HID events (such as the ones generated by some Logitech and
Apple Powerbooks USB keyboards) to the FN keycode.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a quirk for the Apple Powermouse, remapping GenericDesktop.Z to
Rel.HWheel, to allow horizontal scrolling in Linux.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a missing break; statement to the URB status handling
in hid-core.c, avoiding flushing the request queue on success.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The hid now supports the Logitech UltraX Media Remote control.
For now, ID 45 on the consumer usage page has been incorrectly
mapped to KEY_RADIO since no other devices uses it.
Signed-off-by: Micah F. Galizia <mfgalizi@csd.uwo.ca>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fixes handling of multi-transaction reports for HID devices. New
function hid_size_buffers() that calculates the longest report
for each endpoint and stores the result in the hid_device object.
These lengths are used to allocate buffers that are large enough
to store any report on the endpoint. For compatibility, the minimum
size for an endpoint buffer set to HID_BUFFER_SIZE rather than the
known optimal case (the longest report length).
It fixes bug #3063 in bugzilla.
Signed-off-by: Michael Haboustak <mike-@cinci.rr.com>
I simplified the patch a bit to use just a single buffer size.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Extend mapping of the consumer usage page in hid-input.c to handle
more cases appearing on new USB keyboards.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add simulation usage page mappings to hid-input.c to support
a new crop of joysticks using them to designate Rudder and
Throttle controls.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove the "list" member of struct sk_buff, as it is entirely
redundant. All SKB list removal callers know which list the
SKB is on, so storing this in sk_buff does nothing other than
taking up some space.
Two tricky bits were SCTP, which I took care of, and two ATM
drivers which Francois Romieu <romieu@fr.zoreil.com> fixed
up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
There's a "return the wrong SKB" error in the GL620A cable minidriver
(for "usbnet") which can oops. This would not appear when talking
Linux-to-Linux, only Linux-to-Windows (for recent Linuxes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Coverity checker.
(akpm: I stole this from Greg's tree and used the (IMO) tidier sizeof(*p)
construct).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When recently addressing remarks by Alexey Dobriyan about
the isp116x-hcd, I introduced a bug in the driver. Please
apply the attached patch to fix it.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has a one line oops fix, plus related cleanups.
- The bugfix uses microframe scheduling data given to the hardware to
test "is this a periodic QH", rather than testing for nonzero period.
(Prevents an oops by providing the correct answer.)
- The cleanup going along with the patch should make it clearer what's
going on whenever those bitfields are accessed.
The bug came about when, around January, two new kinds of EHCI interrupt
scheduling operation were added, involving both the high speed (24 KBytes
per millisec) and low/full speed (1-64 bytes per millisec) microframe
scheduling. A driver for the Edirol UA-1000 Audio Capture Unit ran into
the oops; it used one of the newly supported high speed modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that I see a bug in hidinput_hid_event. The check for NULL can never
work, becaue &hidinput->input is nonzero at all times.
Cc: <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch does the same swap, i.e. use the ISO macro if (isoc).
Additionally, it fixes the return value - the usb_calc_bus_time function
returns the time in nanoseconds (I didn't notice that before) while the
HS_USECS and HS_USECS_ISO are microseconds. This fixes the function to
return nanoseconds always, and adjusts ehci-q.c (the only high-speed
caller of the function) to wrap the call in NS_TO_US().
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
USB (OHCI) Host driver for S3C2410/S3C2440 based systems
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201
driver. the only missing part is that the corresponding usbid is not
declared. The following patch should fix this.
From: "Mathieu" <matt@minas-morgul.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch enables a support of KYOCERA AH-K3001V, one of the most
popular cell phone in Japan. This device has vendor specific ID but works
with acm driver by adding USB ID. This device already works on
FreeBSD and OS X by native USB ACM driver with USB ID added.
This device is probed as NO_UNION_NORMAL not to hang up when probing.
Signed-off-by: Masahito Omote <omote@utyuuzin.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch handles a rarely-encountered failure mode in usbcore. It's
legal for device_add to fail (although now it happens even more rarely
than before since failure to bind a driver is no longer fatal). So when
we destroy the interfaces in a configuration, we shouldn't try to delete
ones which weren't successfully registered. Also, failure to register an
interface shouldn't be fatal either -- I think; you may disagree about
this part of the patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only uses of both variables were recently removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes an information leak in the usbfs snoop facility:
uninitialized data from __get_free_page can be returned to userspace and
written to the system log. It also improves the snoop output by printing
the wLength value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Fix timeouts in a couple of usb_control_msg() calls due to
change of units from jiffies to milliseconds in 2.6.12.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR. Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds the following new devices to the ftdi_sio driver:
* microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL).
* Evolution Robotics ER1 Control Module submitted by Shawn M. Lavelle.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was already fixed more sufficiently by Andrew Morton's
change 843c944fb8.
Noted by Duncan Sands.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the Option Card driver:
- remove a deadlock
- add sponsor notice
- add new card
- renamed the device to what's usually printed on it
- removed some dead code
- clean up a bunch of irregular whitespace (end-of-line, tabs)
Also add a MAINTAINERS entry for the Option Card driver.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following driver provides complete interrupt-in and interrupt-out
reports (raw data) to a user program. Until now it uses the
HIDIOCGDEVINFO ioctl call, because I don't know better :-(. Perhaps, it
will be ok for you - and I will be happy, if you assign 8 minor numbers.
I have tested it in several environments and it works very well for me.
However, it has a problem with two or more devices at the same hub, if
the two or more devices need 1 ms interrupt-in transfers. Unfortunately
more than one interrupt-in transfer every ms isn't possible (ehci
driver?). This is why the min_interrupt_in_interval and
min_interrupt_out_interval are increased to 2 ms (see the corresponding
module parameters). This way, I can use two devices simultaneously at
the same hub.
Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This increases the reference count on the usb cdc acm control interface
which is referred to by the tty interface provided by the driver. This
allows the deferred removal of the tty after the physical device is
disconnected if the tty is held open at the time of disconnection.
Signed-off-by: brian@murphy.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export usb_get_intf and usb_put_intf so that modules can increase
usb interface reference counts.
Signed-off-by: brian@murphy.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A patch re-organizing some parts of root hub initialization deleted the
code initializing the bus-neutral reboot/shutdown notifier for OHCI.
This patch just restores that deleted code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent "pm_message_t" changes removed functionality from the Linux
PM framework. This patch removes it from the OMAP OHCI too, removing
the distinction between (previous) PM_SUSPEND_MEM and PM_SUSPEND_DISK
state transitions ... now the only suspend semantics supportable are
what was previously PM_SUSPEND_DISK (4) and is now "PMSG_SUSPEND" (3).
From: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor OMAP updates that somehow got dropped from previous patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I also needed the following on 2.6.13-rc1 without CONFIG_USB_ETH_RNDIS,
symbol fs_status_desc isn't available in that case on PXA255.
This builds both with and without ETH_RNDIS, but I haven't actually
tested either.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
below you will find one patch to hid-core.c, which lets usbhid ignore
our HID devices. It would be nice, if you can apply it.
Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The length of the array desc->bitmap is 3, and not 4:
Definitions involved:
In drivers/usb/core/hcd.h
464 #define bitmap DeviceRemovable
In drivers/usb/host/ohci-hub.c
395 struct usb_hub_descriptor *desc
In drivers/usb/core/hub.h
130 struct usb_hub_descriptor {
131 __u8 bDescLength;
132 __u8 bDescriptorType;
133 __u8 bNbrPorts;
134 __u16 wHubCharacteristics;
135 __u8 bPwrOn2PwrGood;
136 __u8 bHubContrCurrent;
137 /* add 1 bit for hub status change; round to bytes */
138 __u8 DeviceRemovable[(USB_MAXCHILDREN + 1 + 7) / 8];
139 __u8 PortPwrCtrlMask[(USB_MAXCHILDREN + 1 + 7) / 8];
140 } __attribute__ ((packed));
In include/linux/usb.h
306 #define USB_MAXCHILDREN (16)
This defect was found automatically by Coverity Prevent, a static analysis
tool.
(akpm: this code should be shot. Field `bitmap' doesn't exist in struct
usb_hub_descriptor. And this .c file is #included in
drivers/usb/host/ohci-hcd.c, and someone somewhere #defines `bitmap' to
`DeviceRemovable'.
>From a maintainability POV it would be better to memset the whole array
beforehand - I changed the patch to do that)
Signed-off-by: Zaur Kambarov <zkambarov@coverity.com>
Cc: <linux-usb-devel@lists.sourceforge.net?
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a basic keypress input driver for the Keyspan Digital
Remote with part number UIA-11. Currently there is an older remote with
part number UIA-10 which isn't supported by this driver. Support for
the older UIA-10 could be added but a binary file is required to be
download to the device, and I don't have that file. I also don't have a
UIA-10 device so I wouldn't be able to test any of the changes.
Signed-off-by: Michael Downey <downey@zymeta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/gadget/net2280.c: In function 'show_registers':
drivers/usb/gadget/net2280.c:1501: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg,
This patch fixes the kmalloc() flags argument type in USB
subsystem; hopefully all of its occurences. The patch was
made against patch-2.6.12-git2 from Jun 20.
Cleanup of flags for kmalloc() in USB subsystem.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sorry that it took so long. Here comes a cleanup patch that
addresses the remarks by Alexey Dobriyan about
gregkh-usb-usb-isp116x-hcd-add.patch EXCEPT the remark about
the typecasting of mem_flags argument for kcalloc; this will
be addressed in a later patch.
OlavCleanup of isp116x-hcd.
Signed off by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make usbmon to print Setup packets of Control transfers. This is useful
when debugging enumeration issues.
This is a change to the trace format which is not fully compatible.
A parser has to look at the data length word now. If that word is
a character like 's', read setup packet before proceeding with data.
I decided not to bump the API tag for this because not many such
parsers exist at this point.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
although 2.6.12 now contains the sisusb driver, it failes to build this
driver due to a missing patch of the Makefile.
From: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We map states 0x00 and 0x10 to the ATM_PHY_SIG_LOST flag. The current logic fails to
resync the line if we get state 0x10 followed by 0x00, since we only resync the line
when the state is 0x00 and the flag changed. Doubly fixed by (1) always resyncing the
line when the state is 0x00 even if the state didn't change, and (2) keeping track of
the last state, not just the flag. We do (2) as well as (1) in order to get better log
messages.
This is a tweaked version of the original patch by Aurelio Arroyo.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No functional change, but less likely to break in the future.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Remove redundant handling of TIOCMBIS and TIOCMBIC ioctls
as they are handled in the tty layer and never reach this driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Use a single usb_device_id table and detect the type of chip
programatically. The table also flags devices requiring special
initialization. The patch makes the driver about 10K smaller and makes
it easier to add new device IDs.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes an unneeded subclass and protocol from the
07af/0005/100 entry in unsual_devs.h as reported by Alfred Ganz
<alfred-ganz@agci.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should do this:
.suspend()
pci_disable_device()
.resume()
pci_enable_device()
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently hid-core follows the same code path for input reports
regardless of whether they are a result of interrupt transfers or
control transfers. That leads to interrupt events erroneously being
reported to hiddev for regular control transfers.
Prior to 2.6.12 the problem was mitigated by the fact that
reporting to hiddev is supressed if the field value has not changed,
which is often the case. Said filtering was removed in 2.6.12-rc1 which
means any input reports fetched via control transfers result in hiddev
interrupt events. This behavior can quickly lead to a feedback loop
where a userspace app, in response to interrupt events, issues control
transfers which in turn create more interrupt events.
This patch prevents input reports that arrive via control transfers from
being reported to hiddev as interrupt events.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Catch up with some PCMCIA API changes:
- Docs say that as of 2.6.11 the PCMCIA IRQInfo2 field is ignored,
but it's not yet removed from the API; stop using it anyway.
- As of 2.6.13 PCMCIA finally hotplugs and does driver binding
without "cardmgr"; add a MODULE_DEVICE_TABLE to support this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes CONFIG_PMAC_PBOOK (PowerBook support). This is now
split into CONFIG_PMAC_MEDIABAY for the actual hotswap bay that some
powerbooks have, CONFIG_PM for power management related code, and just left
out of any CONFIG_* option for some generally useful stuff that can be used
on non-laptops as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one-liner fixes a test for interfaces that are already resumed.
It would be nice if this could get into 2.6.12, but it's not critical
since it only affects people doing selective (runtime) suspend/resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a build error on pxa25x processes with pxa2xx_udc and
CONFIG_USB_ETH=m
# CONFIG_USB_ETH_RNDIS is not set
The error is because on that CPU there's no status transfer support
except with RNDIS. Workaround, enable the RNDIS support too.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One debug message won't print the right value; OSDL bugid 4545.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as527, and was rediffed by me.
Since the IDE interface doesn't convey much information about types of
errors, many USB-IDE adapters report all low-level errors with SK = 0x04,
which is supposed to be used only for non-recoverable errors. As a result
the SCSI midlayer doesn't retry the command. But quite often a retry
would succeed, whereas an unnecessary retry doesn't really hurt anything.
This patch uses a recently-implemented flag to tell the SCSI midlayer that
such hardware errors should be retried.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch causes a port reset whenever there's a transport error or abort.
If that fails it reverts back to doing a mass-storage device reset. It
started life as as497 and was rediffed by me.
This makes error recovery a lot quicker and more reliable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does two things to help reset recovery. It started life as
as496 and was rediffed by me.
First, the patch checks the result of a CLEAR_HALT request and doesn't reset the
endpoint's data toggle unless the request succeeded.
Second, it reduces the timeout for a device reset from 20 seconds to 5
seconds.
If all goes well, then I've finally figured quilt out and this patch should
apply cleanly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
up(&usblp->sem) was called twice in a row in this code path.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> On Sun, Apr 10, 2005 at 07:21:28PM +0600, Viktor A. Danilov wrote:
> >
> > PROBLEM: aiptek input doesn`t register `device` & `driver` section in sysfs (/sys/class/input/event#)
> > REASON: `dev` - field not filled...
> > SOLUTION: in linux/drivers/usb/input/aiptek.c write
> > aiptek->inputdev.dev = &intf->dev;
> > before calling
> > input_register_device(&aiptek->inputdev);
The following (tested) patch fixes the exact same issue with the ATI
Remote input driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for Creative WebCam Go Mini.
Camera has STV680 chip and just different Product ID(0x4007) and Vendor ID (0x041e).
Signed-off-by: Kiril Jovchev <jovchev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initialize status fields in the read and write urbs to prevent a race
condition with open/read/close - open/write/close sequences.
Fixes bug #4432 at bugzilla.kernel.org
Signed-off-by: Adam Oldham <oldhamca@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The itd_patch() function is responsible for allocating entries in the
buffer page pointer list of the iTD. Particularly, a new page pointer
is needed every time when buffer data crosses a page boundary.
However, there is a bug in the allocation logic: the function does not
allocate a new entry when the current transaction is the first
transaction in the iTD (as indicated by first!=0).
The consequence is that, when the data of the first transaction begins
somewhere at the end of a page so that it actually does cross the page
boundary, no new page pointer is allocated. This means that the data
at the end of the first transaction (beyond the page boundary) will be
accessed by the HC using the second page pointer, which is zero.
Furthermore, the first page pointer will be later overwritten by the
page pointers of the other transactions, which will garble it because
the value is or-ed into the iTD field.
All this particular check (for !first) does is cause incorrect
behaviour, so it should be entirely removed (and with it the variable
first that is not used for anything else).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the way uhci-hcd detects valid ports. The
specification doesn't mention any way to find out how many ports a
controller has, so the driver has to use some heuristics, reading the port
status and control register and deciding whether the value makes sense.
With this patch the driver will recognize a typical failure mode (all bits
set to one) for nonexistent ports and won't assume there are always at
least 2 ports -- such an assumption seems silly if the heuristics have
already shown that the ports don't exist.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drain the rndis response queue on disconnect. This fixes a problem
in which an rndis response left in the queue from a previous session
could cause a subsequent session to fail.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a compile glitch with CONFIG_USB_ETH_RNDIS disabled, and
replaces some inline #ifdeffery (and other code) with inline functions
which can evaluate to constants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support to dummy_hcd for suspending and resuming the root
hub and the emulated platform devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the byte-ordering issue for setup packets in the
dummy_hcd driver and cleans up a few things that sparse -Wbitwise
dislikes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
you seem to have applied the original, not the new improved one with
whiter teeth that uses kcalloc instead of kmalloc + memset. Here's a
patch that goes on top of the one you applied.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Work around the gcc-2.95.x macro expansion bug.
Cc: Duncan Sands <baldrick@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Zero the entire instance, not just the struct usbatm_data head.
Make sure the just allocated urb is freed if we fail to allocate
a buffer. Based on a patch by Stanislaw W. Gruszka.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of "unknown vpi/vci" debug messages to (usually) at most
one per-urb, rather than one per-cell. This is only an issue when (a) many
packets come in but no connection is open; and (b) CONFIG_USB_DEBUG is set.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doesn't do any firmware loading etc, just transmission and reception.
The user needs to take care of modem initialization, and load the
module with parameters giving the endpoints to use and so forth.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for modems based on the Conexant AccessRunner chipset.
Original patch by Josep Comas, much reworked by Roman Kagan.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Port the speedtch driver to the new usbatm core. The code is much
the same as before, just reorganized, though I threw in some minor
improvements (a new module parameter for choosing the altsetting,
more robust urb failure handling, ...) while I was there.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the core usbatm code: minidrivers (i.e. drivers for particular
modems) now register themselves with the usbatm core, supplying methods
for binding/unbinding etc. The design was inspired by usb-serial and
usbnet. At the same time, more common code from the speedtch and
cxacru (patch 3/5) drivers was generalized and moved into the core. The
transmission and reception parts have been unified and simplified. Since
this is a major change and I don't like underscores in file names,
usb_atm.[ch] has been renamed usbatm.[ch].
Many thanks to Roman Kagan, who did a lot of the coding.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various minor EHCI updates
* Dump some more info in the debug dumps, notably the product
description (e.g. chip vendor), BIOS handhake flags, and
debug port status (when it's not managed by the HCD).
* Minor updates to the BIOS handoff code: always flag the HCD
as owned by Linux (in case BIOS doesn't grab it "early"),
and on the buggy-BIOS path always match the "early handoff"
code and forcibly disable SMI IRQs.
* For the disabled 64bit DMA support, there's now a constant
to use for the mask; use it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has several small updates to the px2xx UDC driver:
* small fixes from Eugeny S. Mints <emints@ru.mvista.com>
- local_irq_save() around potential endpoint disable race
- fix handling of enqueue to OUT endpoints (potential oops)
* add shutdown() method to disable any D+ pullup
* rename methods accessing raw signals, referencing the signals
* describes itself as for "pxa25x", since pxa27x is different
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sparse updates; and the API change for SETUP packets being in USB byteorder.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is mostly "sparse" related updates, one of which was a missing
le32_to_cpu() should have affected big-endian hardware.
Notable is the API change: setup packets are now provided in USB
byte order. This affects only big-endian hardware, and the gadget
drivers have been updated in a separate patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates most of the gadget framework to expect SETUP packets use
USB byteorder (matching the annotation in <linux/usb_ch9.h> and usage
in the host side stack):
- definition in <linux/usb_gadget.h>
- gadget drivers: Ethernet/RNDIS, serial/ACM, file_storage, gadgetfs.
- dummy_hcd
It also includes some other similar changes as suggested by "sparse",
which was used to detect byteorder bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents gadget drivers from being selected when no controller has
been selected, by adding an additional boolean and depending on it.
It's mostly to help "allmodconfig".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the dummy_hcd driver use emulated root-hub interrupts
instead of polling. It's in the spirit of similar changes being made to
the other HCDs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds to the dummy_hcd driver a new routine for keeping track of
all changes in the state of the emulated USB link. The logic is now kept
in one spot instead of spread around, and it's easier to verify and
update the code. The behavior of the port features has been corrected in
a few respects as well (for instance, if the POWER feature is clear then
none of the other features can be set).
Also added is support for the (relatively new) _connect() and
_disconnect() calls of the Gadget API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the dummy_hcd driver create separate platform devices for
the emulated host controller and emulated device controller. This gives a
more accurate simulation and will permit testing of situations where only
one of the two devices is suspended.
This also changes the name of the host controller platform device to match
the name of the driver. That way the normal platform bus probe mechanism
will handle binding the driver to the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes some cosmetic changes to dummy_hcd:
Minor alterations of comments and whitespace.
Replace USB_PORT_FEAT_xxx with USB_PORT_STAT_xxx. This is
appropriate as the values are stored in a status variable
and they aren't feature indices. Also it allows the
elimination of a bunch of awkward bit shift operations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial OTG support for dummy_hcd, mostly as a framework for further work.
It emulates the new OTG flags in the host and peripheral frameworks, if
that option is configured. But it's incomplete:
- Resetting the peripheral needs to clear the OTG state bits;
a second enumeration won't work correctly.
- This stops modeling HNP right when roles should switch the first time.
It should probably disconnect, then set the usb_bus.is_b_host and
usb_gadget.is_a_peripheral flags; then it'd enumerate almost normally,
except for the role reversal. Roles could then switch a second time,
back to "normal" (with those flags cleared).
- SRP should be modeled as "resume from port-unpowered", which is
a state that usbcore doesn't yet use.
HNP can be triggered by enabling the OTG whitelist and configuring a
gadget driver that's not in that list; or by configuring Gadget Zero
to identify itself as the HNP test device.
Sent-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
More omap_udc updates:
* OMAP 1710 updates
- new UDC bit for clearing endpoint toggle, affecting CLEAR_HALT
- new OTG bits affecting wakeup
* Fix the bug Vladimir noted, that IN-DMA transfer code path kicks in
for under 1024 bytes (not "up to 1024 bytes")
* Handle transceiver setup more intelligently
- use transceiver whenever one's available; this can be handy
for GPIO based, loopback, or transceiverless configs
- cleanup correctly after the "unrecognized HMC" case
* DMA performance tweaks
- allow burst/pack for memory access
- use 16 bit DMA access most of the time on TIPB
* Add workarounds for some DMA errata (not observed "in the wild"):
- DMA CSAC/CDAC reads returning zero
- RX/TX DMA config registers bit 12 always reads as zero (TI patch)
* More "sparse" warnings removed, notably "changing" the SETUP packet
to return data in USB byteorder (an API change, null effect on OMAP
except for these warnings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some cleanup for the the Ethernet part of the Ethernet/RNDIS gadget driver:
- Remove remnants of ancient endpoint init logic; this is simpler, clearer
- Save a smidgeon of space in the object file
- Get rid of some #ifdeffery, mostly by using some newish inlines
- Reset more driver state as part of USB reset
- Remove a needless wrapper around an RNDIS call
- Improve and comment the status interrupt handling:
* RNDIS sometimes needs to queue these transfers (rarely in normal
cases, but reproducibly while Windows was deadlocking its USB stack)
* Mark requests as busy/not
- Enable the SET_NETDEV_DEV() call; sysfs seems to behave sanely now
This is a net shrink of source code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some bugfixes and lots of cleanup (net code shrink):
- On reset, force the RNDIS state machine its initial state
- Hook up the RNDIS (outgoing) filters to the CDC mechanism
- Lots of cleanup:
* Eliminate duplicate copy of OID table;
* Unify handlying of the OID "query" response data pointer;
* Reduce code duplication for calculating query response lengths;
* Remove some checks for "can't happen" errors;
* Get rid of debugging #ifdefs by making the debug flag an integer level
Most of the patch, by volume, relates to those query response cleanups.
It incidentally shaves off a few hundred bytes of object code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the host controller drivers; they no longer need to
register their root hubs because usbcore will take care of it for them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes usbcore automatically allocate and register the root hub
device for a new host controller when the controller is registered. This
way the HCDs don't all have to include the same boilerplate code. As a
pleasant side benefit, the register_root_hub routine can now be made
static and not EXPORTed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the HCDs that used the old hub_set_power_budget call,
making them use the new hcd->power_budget field instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch simplifies the uhci-hcd driver by removing the device pointer
currently stored in the QH and TD structures. Those pointers weren't
being used for anything other than to increment the device's reference
count, which is unnecessary since the device is used only when an URB
completes, and outstanding URBs take their own reference to the device.
As a useful side effect, this change means that uhci-hcd no longer needs
to have the root-hub device available in the start routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the hub_set_power_budget routine, which was used by a
couple of HCDs to indicate that the root hub was running on battery power.
In its place is a new field added to struct usb_hcd, which HCDs can set
before the root hub is registered. Special-case code in the hub driver
knows to look at this field when configuring a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My patch adding PM support for zd1201 didn't check for the device on
resume, which can oops if the device has been removed.
This patch fixes it.
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch enables power management (suspend, resume) support for zd1201.
It fixes problems after wakeup for me, but these problems did not appear
everytime without this patch. it's a bit empirical, based on what the
usbnet does, so maybe not correct... Maybe someone can give it a look
before it's applied.
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds a reboot notifier to OHCI, mostly to benefit kexec; plus
minor #include tweaks.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to "usbtest" driver:
* Improve some diagnostics. One path that never generated diagnostics
before should now generate two ... unless you hit a GCC bug that
all my compilers seem to have, go figure.
* Add suspend/resume support, so this behaves when the Linux host
being used for testing suspends.
* Don't test the "zero byte ep0 read" case unless real-world relevance
for the testing is is irrelevant.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes lost LF when ACM device is used with getty/login/bash,
in case of a modem which takes calls.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a revised version of an earlier patch to add support to usbcore
for driving root hubs by interrupts rather than polling.
There's a temporary flag added to struct usb_hcd, marking devices whose
drivers are aware of the new mechanism. By default that flag doesn't get
set so drivers will continue to see the same polling behavior as before.
This way we can convert the HCDs one by one to use interrupt-based event
reporting, and the temporary flag can be removed when they're all done.
Also included is a small change to the hcd_disable_endpoint routine.
Although endpoints normally shouldn't be disabled while a controller is
suspended, it's legal to do so when the controller's driver is being
rmmod'ed.
Lastly the patch adds a new callback, .hub_irq_enable, for use by HCDs
where the root hub's port-change interrupts are level-triggered rather
than edge-triggered. The callback is invoked each time khubd has finished
processing a root hub, to let the HCD know that the interrupt can safely
be re-enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After all the discussion you might not be interested in this still, but
nevertheless here it is. This patch adds a shutdown method to the
uhci-hcd driver. Its prerequisite is the patch you wrote adding shutdown
support for PCI.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch improves the strategy uhci-hcd uses for performing controller
resets and checking whether they are needed.
The HCRESET command doesn't affect the Suspend, Resume,
or Reset bits in the port status & control registers, so
the driver must clear them by itself. This means the
code to figure out how many ports there are has to be moved
to an earlier spot in the driver.
The R/WC bits in the USBLEGSUP register can be set by the
hardware even in the absence of BIOS meddling with legacy
support features. Hence it's not a good idea to check them
while trying to determine whether the BIOS has altered the
controller's state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, which has as478b as a prerequisite, enables the uhci-hcd
driver to take advantage of root-hub IRQs rather than polling during the
time it is suspended. (Unfortunately the hardware doesn't support
port-change interrupts while the controller is running.) It also turns
off the driver's private timer while the controller is suspended, as it
isn't needed then. The combined elimination of polling interrupts and
timer interrupts ought to be enough to allow some systems to save a
noticeable amount of power while they are otherwise idle.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tidies up a few loose ends left by the preceding patches.
It indicates the controller supports remote wakeup whenever the PM
capability is present -- which shouldn't cause any harm if the
assumption turns out to be wrong. It refuses to suspend the
controller if the root hub is still active, and it refuses to resume
the root hub if the controller is suspended. It adds checks for a
dead controller in several spots, and it adds memory barriers as
needed to insure that I/O operations are completed before moving on.
Actually I'm not certain the last part is being done correctly. With
code like this:
outw(..., ...);
mb();
udelay(5);
do we know for certain that the outw() will complete _before_ the
delay begins? If not, how should this be written?
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements (finally!) separate suspend and resume routines
for the root hub and the controller in the UHCI driver. It also
changes the sequence used to reset the controller during initial
probing, so as to preserve the existing state during a Resume-From-Disk.
(This new sequence is what should be used in the PCI Quirks code for
early USB handoffs, incidentally.) Lastly it adds a notion of the
controller being "inaccessible" while in a PCI low-power state, when
normal I/O operations shouldn't be allowed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch starts making some serious changes to the UHCI driver.
There's a set of private states for the root hub, and the internal
routines for suspending and resuming work completely differently, with
transitions based on the new states. Now the driver distinguishes
between a privately auto-stopped state and a publicly suspended state,
and it will properly suspend controllers with broken resume-detect
interrupts instead of resetting them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes a few small improvements in the UHCI driver. Some
code is moved between different source files and a more useful pointer
is passed to a callback routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves a few subroutines around in the uhci-hcd source file.
Nothing else is changed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch turns a user mode driver error into a hard error, and updates
the relevant diagnostic slightly to help troubleshooting. gphoto was
known to have this problem, hopefully it is now fixed (they have had
plenty of warning...)
This had been left as a soft error to give various user mode drivers a
change to be properly fixed, with the statement that starting in about
2.6.10 it would be changed. It had been mostly safe as a soft error ...
but that can not be guaranteed. Now that a year has passed, it's time to
really insist that the user mode drivers finally fix their relevant bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an oops triggered at rmmod of isp116x-hcd
after the probe() has failed.
Also, it extends the error message printed, if the driver
cannot detect "Chip's Clock Ready" after a software reset.
As Ian Campbell recently reported, this happens if the
chip's H_WAKEUP pin is not pulled low during software reset.
Several people have already had this issue, hence the update
to the error message.
Also, extend the error message about the failed clock
detection after the software reset.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
This patch provides an "isp116x-hcd" driver for Philips'
ISP1160/ISP1161 USB host controllers.
The driver:
- is relatively small, meant for use on embedded platforms.
- runs usbtests 1-14 without problems for days.
- has been in use by 6-7 different people on ARM and PPC platforms,
running a range of devices including USB hubs.
- supports suspend/resume of both the platform device and the root hub;
supports remote wakeup of the root hub (but NOT the platform device)
by USB devices.
- does NOT support ISO transfers (nobody has asked for them).
- is PIO-only.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various USB patches, mostly for portability:
- Fifo mode 1 didn't work previously (oopsed), so now it's fixed and
(why not) defines even more endpoints for composite devices.
- OMAP 1710 doesn't have an internal transceiver.
- Small PM update: if the USB link is suspended, don't disconnect on
entry to deep sleep.
- Be more correct about handling zero length control reads. OMAP
seems to mis-handle that protocol peculiarity though; best avoided.
- Platform device resources (for UDC and OTG controllers) now use
physical addresses, so /proc/iomem is more consistent.
- Minor cleanups, notably (by volume) for "sparse" NULL warnings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch changes the g_file_storage driver to make the "stall" module
parameter generally available; currently it is available only if the
testing version of the module has been configured. It also fixes a typo
in a comment -- thanks, Pat!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch simplifies the g_file_storage driver by consolidating a bunch
of min() calculations at a single spot.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB ethernet drivers did not accept multicast frames appropriately.
IPv6 did not work with those drivers without this patch.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/media/pwc/pwc-uncompress.c: In function `pwc_decompress':
drivers/usb/media/pwc/pwc-uncompress.c:140: warning: unreachable code at beginning of switch statement
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various filesystem drivers have grown a get_dentry() function that's a
duplicate of lookup_one_len, except that it doesn't take a maximum length
argument and doesn't check for \0 or / in the passed in filename.
Switch all these places to use lookup_one_len.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers need to return -ENODEV when they can't bind to a device.
Anything else stops the "bind a device to a driver" search.
From: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes usb_driver_release_interface() to make it avoid calling
device_release_driver() recursively, i.e., when invoked from within the
disconnect routine for the same device. The patch applies to your
"driver" tree.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code looks like this:
/* if interface was already added, bind now; else let
* the future device_add() bind it, bypassing probe()
*/
if (!list_empty (&dev->bus_list))
device_bind_driver(dev);
IOW, it's checking to see if the device is attached to the bus or not
and binding the driver if it is. It's checking the device's bus list,
which will only appear empty when the device has been initialized, but
not added. It depends way too much on the driver model internals, but it
seems to be the only way to do the weird crap they want to do with
interfaces.
When I converted it to use klists, I accidentally inverted the logic,
which led to bad things happening. This patch returns the check to its
orginal value.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/usb.c
===================================================================
Trivial fix to USB class-creation error path; please apply.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core:
change driver's, bus's, class's and platform device's names
to be const char * so one can use
const char *drv_name = "asdfg";
when initializing structures.
Also kill couple of whitespaces.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the EHCI driver spin a bit longer before concluding that the
port reset failed. "Obviously safe."
It allows some devices to enumerate that previously didn't. We've seen
a bunch of these problem reports recently, this will make some go away.
As reported by Michael Zapf <Michael.Zapf@uni-kassel.de>, some EHCI
controllers seem to take forever to finish port resets and produce
"port N reset error -110" type errors. Spinning a bit longer helps.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pwc chainsaw session left some setups not working. There is a
sanity check on compression buffers that simply isn't right any more as
we never allocate one.
This doesn't address the email and other changes. I'll do those
tomorrow if I get time, but it is the minimal fix for the code and basic
feature set.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Avoid losing bytes at tty-ldisc.
This patch was originally developed by Daniel Smertnig. I
(Ian Abbott) made a few changes. It has been tested by both
Daniel and I, at least for raw, non-canonical receive data
processing.
Here is Daniel's original description of the patch:
===
During a project in which I was using a FTDI 232BM to
transmit data at relative high speeds (625kBit/s), I
noticed a problem where data was lost even if flow
control was enabled: The FTDI-Driver receives 512 Bytes
of data over USB at a time, which consists of 8 64-Byte
packets. Subtracting the 2 bytes of status information
included in each packet this gives 496 "real" data
bytes per read.
This data is passed (indirectly, via the flip buffers)
to the tty line discipline which takes care of
throttling when there the free buffer space reaches
TTY_THRESHOLD_THROTTLE (128). Because the FTDI driver
processes up to 496 bytes at a time, throttling won't
happen in time and the line discipline will discard the
remaining bytes.
To avoid this the patch passes data in 62-byte blocks
to the tty layer and checks the available space in the
ldisc-buffers. If there isn't enough free space,
processing the rest of the data is delayed using a
workqueue.
Note: The original problem should be easily
reproducible with a userspace program which does slow &
small reads.
===
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Daniel Smertnig <daniel.smertnig@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This "obvious" one-liner is needed to recognize Zaurus SL 6000;
it just checks two GUIDs not just one.
OSDL bugids #4512 and #4545 seem to be duplicates of this report.
From: Gerald Skerbitz <gsker@tcfreenet.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added support to get/set flow control line levels using TIOCMGET and
TIOCMSET.
Added support for RTSCTS hardware flow control.
cp2101_get_config and cp2101_set_config modified to support long request
strings, required for configuring flow control.
Signed-off-by: Craig Shelley craig@microtron.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original entry of this patch was submitted by Filippo Bardelli
<filibard@libero.it>, with cleanups and patch-ification by me.
This corrects the subclass that the device reports.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the code to provide modalias in sysfs for usb devices
56 bytes smaller in i386, while making it clear that the first part of
the modalias string is the same no matter what the device class is.
Signed-Off-By: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new driver for "Option" cards. This is a GSM data card,
controlled by three "serial ports" which are connected via an OHCI adapter,
all located on an oversized PC-Card. It's sold by several GSM service
providers.
Traditionally, this card has been accessed via the standard serial driver
and appropriate vendor= and product= options. However, testing has
revealed several problems with this approach, including hung data transfers
and lost data blocks when receiving.
Therefore, I've written a separate driver.
Signed-off-by: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They aren't really HID devices.
Damm microsoft HID driver, that thing has caused more companies to have
to do this kind of hack...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the DeLorme Earthmate lt-20 productid to the hid
blacklist table. This patch ensures the lt-20 can be claimed by the
appropriate driver (cypress_m8).
Adds the product id 0x200, of the DeLorme Earthmate lt-20, to the hid
blacklist table.
Signed-off-by: Lonnie Mendez <lmendez19@austin.rr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the outdated ChangeLog file for this driver.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At module load time, if a generic device is found, the tty information
for the device is not set up properly (as the tty structures aren't initialized
yet.) This can cause big problems for things like udev. This patch fixes this.
Thanks to Kay Sievers for the original patch for this problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Add PID for "ELV USB Module UM100".
PID sent by Armin Laugher.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for a CF-card USB Host adapter, the Ratoc REX-CFU1U, by
wrapping a PCMCIA driver around the existing "sl811-hcd" platform driver.
This CF card is especially useful for PDAs, which currently tend to have
no other solution for USB host capability.
From: Botond Botyanszki <boti@rocketmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to the sl811-hcd driver:
* Fix small glitches that crept in during recent evolution of usbcore's hcd
glue layer, coupling endpoint state records to usbcore and active urbs.
(As noted by folk whose boards weren't stuck on 2.6.9 kernels...)
* Cope with various system-specific issues:
- Some configurations (e.g. a CF-card uses this chip) have iospace
addresses for the two registers, rather than memory mapped ones.
- Some configurations do interesting things with IRQs; maybe the
line is shared, or it doesn't support level triggering.
- Not all boards can drive the chip reset line in software.
* Address a potential race during unlinking.
* Tweak probe/remove section info to handle the case where this segment
of a platform bus is hotpluggable (e.g. CF card). (The basic problem
is that CONFIG_HOTPLUG is global, which is wrong since not all busses
can hotplug even on hotplug-friendly systems...) Also export the
driver, so that the CF driver can depend on it.
Also removed some annoying end-of-line whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
due to a masking bug in hid-core.c:extract(). This patch fixes it
up by forcing the mask to be 64 bits wide.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Windows does. This should make life easier for devices that were
tested with Windows only.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The neutering of the pwc driver was incomplete. It still references
some now-dead files..
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In netdev-2.6 we need to update zd1201.c since we don't have
driver/net/wireless/ieee802_11.h anymore.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
The original pwc author raised some questions about the reverse
engineering of the decompressor algorithms used in the pwc driver.
Having done some detailed investigation it appears those concerns that
clean room policy was not followed are reasonable. I've also had a
friendly discussion with Philips to ask their view on this.
This removes the problem items of code which reduces the pwc
functionality in the kernel a little but leaves all the framework for
setup that will be needed for decompressors in user space (where they
eventually belong). This change set is designed to be the minimal risk
change set given that 2.6.12 is hopefully close to hand, with a view to
merging the much updated pwc code in 2.6.13 series kernels.
Someone else can then redo the decompressors properly (clean room) in
user space.
Note that while its easy to say that it should have been caught earlier,
but the violation was really only obvious to someone who had access to
both the proprietary source and the 'GPL' source.
There's a bigger Speedtouch update coming your way after 2.6.12 but in
the meantime, let's at least make it automatically resync if the DSL
signal is lost.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the DeLorme Earthmate lt-20 to the
cypress_m8 driver. The device was tested and found to be compatible
with the cypress_m8 driver. This is a resend with the complete patch
which properly compiles.
Adds support for the DeLorme Earthmate lt-20 to the cypress_m8 driver.
Signed-off-by: Lonnie Mendez <lmendez19@austin.rr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Force the EHCI watchdog timer off during suspend, in case for some
reason it was still running after the root hub suspended.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to the usbnet driver:
- Remove a warning when built with Zaurus support but not CDC Ethernet;
just moves an #ifdef to cover more code
- Two tweaks to the pseudo-MDLM support:
* correctly handle _either_ of the two GUIDs
* ignore a padding bit that doesn't seem necessary
- Remove ID for one Motorola phone that uses the MDLM stuff.
It also updates the Kconfig helptext to make it clearer that the "Zaurus"
configuration option supports an increasing (sigh) family of nonstandard
peripheral protocols.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed problem where setting or retreiving the serial config would fail
with EPIPE. Removed CRTS toggling so the driver behaves more like other
usbserial adapters. Issued new interval of 1ms instead of the default
bInterval. As a result, transfer speed has been substantially
increased. From avg. 850bps to avg. 3300bps. Also added new module
parameter 'interval' to tweak the interval in case this change causes
problems for someone. Cleaned up code and formatting issues so source
is more readable. Replaced the C++ style comments. Various other code
cleanups.
Signed-off-by: Lonnie Mendez <lmendez19@austin.rr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for the Minolta Dimage Z10.
Originally reported by Vilisas <vilisas@xxx.lt>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ftdi_sio] Replaced redundant INTERFACE_A and INTERFACE_B macros with
the equivalent PIT_SIOA and PIT_SIOB macros.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some VID/PID updates for the ftdi_sio driver:
* The "Gude Analog- und Digitalsysteme GmbH" entries were missing from
the "combined" table.
* Replaced FTDI_8U232AM_ALT_ALT_PID with 3 PIDs for devices from
4n-galaxy.de.
* Removed redundant FTDI_RM_VID and renamed FTDI_RMCANVIEW_PID to
FTDI_RM_CANVIEW_PID.
* Added VID/PID for serial converter in Mobility Electronics EasiDock
USB 200 (mentioned by Gregory Schmitt).
* Added PID for Active Robots USB comms board (mentioned by John Koch).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -ur a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
On Thu, Apr 14, 2005 at 11:06:21PM +0400, Sergey Vlasov wrote:
> http://thread.gmane.org/gmane.linux.usb.devel/32977
>
> (see "[PATCH] N/3 cdc acm errors").
>
> You also need this driver core fix:
>
> http://thread.gmane.org/gmane.linux.usb.devel/33132
I reproduced the same oops while trying to execute at+mode=99, it would
be nice to get these fix merged since I believe it's still needed to
connect the laptop over gprs (something I didn't test yet).
This further patch will allow you to connect via usbnet, Greg could you
apply? Thanks!
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Miscellaneous updates for EHCI.
- Mostly updates the power switching on EHCI controllers. One routine
centralizes the "power on/off all ports" logic, and the capability to
do that is reported more correctly.
- Courtesy Colin Leroy, a patch to always power up ports after resumes
which didn't keep a USB device suspended. The reset-everything logic
powers down those ports (on some hardware) so something needs to turn
them back on.
- Minor tweaks/bugfixes for the debug port support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a compiler error caused by a missing prototype. It should
apply directly to Greg KH's usb-2.6.git tree.
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when stealing code from ati_remote for a GPL-driver of my usbradio (because of
its neat usb int transfers) I found out, that the inbuf is freed twice.
I don't have the ati-remote, so I don't know it is a problem at all, but it
looks strange to me anyway. Also I don't know if it has been fixed already in
newer kernel versions.
From: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a somewhat more comprehensive fix for the problem of devices
like the newer Zaurii ... or in this case some Motorola cell phones.
To recap, the problem's root cause is that these devices aren't using
standard USB class specifications for their network links, and so far
we've had to add lots of device-specific driver entries. The vendor
fix abuses the CDC MDLM descriptors (they _could_ have conformed to
the spec, but didn't) and defines a "Belcarra firmware" pseudo-class.
This patch recognizes that pseudo-class by the GUIDs in those descriptors,
and handles the devices that just use the Zaurus framing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the ASIX USB Ethernet code to make use of the new status
infrastructure in usbnet.
Additionally, add a link_reset() handler to the struct usbnet
structure to provide a generic means for a driver to perform link
reset tasks such as a determining link speed and setting
device flags accordingly.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below adjusts the MODALIAS generated by the usb hotplug
function to match the proposed change to scripts/mod/file2alias.c.
Signed-off-by: Roman Kagan <rkagan@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz wrote:
> 1. You're adding product IDs 1202, 1203, 1204, and 1205. 1203 was
> already there, but you remove it, OK, but 1205 is already there, so
> you'll need to fix that.
I was not removing 1203, it's just the extension of the bcd range. You are
right about 1205, as I wrote, it was a patch against 2.6.11.7. Attached is
a patch against 2.6.12-rc2.
> 2. I'm OK with the full bcd range if Apple is changing it on firmware
> revs... fine, but it's bcd, not hex... 0x9999 =)
I just copied from other entries. There're a lot 0xffffs in unusual_dev.h,
so I assumed it is correct. I changed it to 0x9999.
> 3. It's rather obnoxious to take the original submitter's credit away.
I didn't remove it, I changed it to "based on...". Because I changed
something (the range) in his entry, I thought it is the best to take the
responsibility but keep the origin. Anyway, in the new patch I did it in a
different way.
> 4. Your /proc/bus/usb/devices shows 1204, but I see no evidence 1202 is
> really an iPod.
I don't have an old iPod mini, but you find a lot of evidence here:
http://www.google.com/search?q=0x1202+ipod
Especially this one:
http://www.qbik.ch/usb/devices/showdescr.php?id=2737
> It also looks like 1205's entry is getting mangled, but I haven't
> attempted to apply the patch, so I'm not sure.
No, the patch was ok, but I agree it looks strange. It's not very
readable, because I cannot tell diff to work blockwise instead of
linewise. Because of the similarity of the entries, diff splits and merges
them. Anyway, the new patch "looks" better. ;-)
Signed-off-by: Sven Anderson <sven-linux@anderson.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kobject_add() and kobject_del() don't emit hotplug events anymore.
We need to do it ourselves now.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to the Ethernet/RNDIS gadget driver (mostly for RNDIS):
- Fix brown-paper bag goof with RNDIS packet TX ... the wrong length
field got set, so Windows would ignore data packets it received.
- More consistent handling of CDC output filters (but not yet hooking
things up so RNDIS uses the mechanism).
- Zerocopy RX for RNDIS packets too (saving CPU cycles).
- Use the pre-allocated interrupt/status request and buffer, rather
than allocating and freeing one of each every few seconds (which
could fail).
- Some more "sparse" tweaks, making both dual-speed and single-speed
configurations happier.
- RNDIS speeds are reported in units of 100bps, not bps.
Plus two minor cleanups (whitespace, messaging).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of a bunch of redundant NULL pointer checks in drivers/usb/*,
there's no need to check a pointer for NULL before calling kfree() on it.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/class/audio.c
===================================================================
Checking for NULL before calling kfree() is redundant. This patch removes
these redundant checks and also makes a few tiny whitespace changes.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please accept the attached patch which adds the vendorid 0x0745 and
modelid 0x0001 (ID 0745:0001) "Syntech Information Co., Ltd."
The device is an USB IR cradle for a barcode scanner (CPT-8001C) from
Cipherlab.
From: Peter Favrholdt <pfavr@mip.sdu.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -u kernel-source-2.6.11/drivers/usb/serial/pl2303.c ../kernel-source-2.6.11/drivers/usb/serial/pl2303.c
I'm attaching a patch to fix status when using Siemens X65
mobile. This mobile use first byte instead of normal UART_STATE
byte.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/serial/pl2303.c
===================================================================
It's possible to unplug usb device and do tiocmset() and tiocmget() without
valid interface in pl2303 module.
The patch below check this and return -ENODEV if interface was removed.
From: Flavio Leitner <fbl@conectiva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -purN linux-05-04-11/drivers/usb/serial/pl2303.c linux-05-04-11.usb/drivers/usb/serial/pl2303.c
In response to complaints about excessive latency in the uhci-hcd driver
I'm planning to convert it to a top-half/bottom-half design. It turns out
that to do this, the USB API has to be modified slightly since the driver
will not be able to meet one of the guarantees in the current API. This
patch changes some kerneldoc, specifying the weaker guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a quirk to the OHCI driver that lets it work with an old
Compaq implementation. It also removes some needless strings from
the non-debug version of the driver.
Signed-off-by: Chris Clayton <chris_clayton@f1internet.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hmm, another case of a Zaurus ROM not telling the expected conformance lie;
this patch handles the lies told by the SL5600.
From: bender647@gmail.com
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the attached patch adds another USB device ID to the list. Seems the
device is known under multiple IDs.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the delay for the US_FL_GO_SLOW patch from 110us to 125.
Some delays need this extra delay includign Jan De Luyck's drive which spawned
the original increase from 110 to 110us. 125 is a microframe, so this delay
seems to make sense more than just be a random delay (thanks to David Brownell
for pointing that out after my original patch).
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/storage/transport.c
===================================================================
On ppc64:
drivers/usb/net/usbnet.c: In function `skb_return':
drivers/usb/net/usbnet.c:429: warning: int format, different type arg (arg 3)
drivers/usb/net/usbnet.c:429: warning: int format, different type arg (arg 3)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -puN drivers/usb/net/usbnet.c~usbnet-printk-warning-fix drivers/usb/net/usbnet.c
I am sorry that the last patch about 32 bit compat ioctl on
64 bit kernel actually breaks the usbdevfs. That is on the current
BK tree. I am retarded.
Here is the patch to fix it. Tested with USB hard disk and webcam
in both 32bit compatible mode and native 64bit mode.
Again, sorry about that.
From: Christopher Li <chrisl@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts a recent change to usb_set_interface(). The change worked
around a quirk in certain devices, but doing this in usbcore creates
needless regressions for other devices. More appropriate fixes won't
put such handling in usbcore.
Basically it's tricky to do a full software reset of USB device state, since
the devices don't all act the same. This adds a note to the kerneldoc for
the usb_reset_configuration() call to highlight the quirk this was working
around: endpoint data toggles not being reset.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
First patch incorrectly changed state of the wait-queue usage to
TASK_UNINTERRUPTIBLE. Reverted to TASK_INTERRUPTIBLE.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch includes minor "sparse -Wbitwise" updates for the PCI based
HCDs. Almost all of them involve just changing the second parameter of the
suspend() method to a pm_message_t ... the others relate to how the EHCI
code walks in-memory data structures. (There's a minor bug fixed there too
... affecting the big-endian sysfs async schedule dump.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/hcd.h
===================================================================
This is the first of a few installments of PM API updates to match the
recent switch to "pm_message_t". This installment primarily affects
USB device drivers (for USB interfaces), and it changes the handful of
drivers which currently implement suspend methods:
- <linux/usb.h> and usbcore, signature change
- Some drivers only changed the signature, net effect this just
shuts up "sparse -Wbitwise":
* hid-core
* stir4200
- Two network drivers did that, and also grew slightly more
featureful suspend code ... they now properly shut down
their activities. (As should stir4200...)
* pegasus
* usbnet
Note that the Wake-On-Lan (WOL) support in pegasus doesn't yet work; looks
to me like it's missing a request to turn it on, vs just configuring it.
The ASIX code in usbnet also has WOL hooks that are ready to use; untested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/net/irda/stir4200.c
===================================================================
This has a variety of updates to the shared suspend/resume code for
PCI based USB host controllers.
- Cope with pm_message_t replacing the target system state.
This is actually a loss of functionality; PCI D1 and D2
states will no longer be used, and it's no longer knowable
that D3cold is on the way so power will be lost.
- Most importantly, some of the resume paths are reworked and
cleaned up. They're now an exact mirror of suspend paths,
and more care is taken to ensure the hardware is reactivated
before the hardware re-enables interrupts.
Plus comment and diagnostic cleanups; there are some nasty cases here
especially combined with swsusp, now they're somewhat commented.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -puN drivers/usb/core/hcd-pci.c~usb-resume-fixes drivers/usb/core/hcd-pci.c
Here's a tiny patch to add support for the Tapwave Zodiac (for
2.6.11.6). I've been meaning to send it in for a while but kept
upgrading my kernel and losing the changes :-) I own the device and it
works fine with the latest pilot-link beta.
From: Larry Battraw <lbattraw@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Jamieson Becker <jamie@jamiebecker.com> for the info
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff -Naur -X dontdiff-osdl tmp/linux-2.6.12-rc2/drivers/usb/serial/visor.h linux-2.6/drivers/usb/serial/visor.h
Fix up two drivers that incorrectly were using the old return values for
their new-style EH methods and kill off scsi_obsolete.h that defined the
constants. The initio driver has all these constansts defined locally
and uses them internally, I'll fix that up some time later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix up two drivers that incorrectly were using the old return values for
their new-style EH methods and kill off scsi_obsolete.h that defined the
constants. The initio driver has all these constansts defined locally
and uses them internally, I'll fix that up some time later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
