Use the standard magic.h for kvmfs.
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A bogus 'return r' can cause an otherwise successful module load to fail.
This both denies users the use of kvm, and it also denies them the use of
their machine, as it leaves a filesystem registered with its callbacks
pointing into now-freed module memory.
Fix by returning a zero like a good module.
Thanks to Richard Lucassen <mailinglists@lucassen.org> (?) for reporting
the problem and for providing access to a machine which exhibited it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Enabling dirty page logging is done using KVM_SET_MEMORY_REGION ioctl.
If the memory region already exists, we need to remove write accesses,
so writes will be caught, and dirty pages will be logged.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Since dirty_bitmap is an unsigned long array, the alignment and size need
to take that into account.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A few places where we modify guest memory fail to call mark_page_dirty(),
causing live migration to fail. This adds the missing calls.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Allocate a distinct inode for every vcpu in a VM. This has the following
benefits:
- the filp cachelines are no longer bounced when f_count is incremented on
every ioctl()
- the API and internal code are distinctly clearer; for example, on the
KVM_GET_REGS ioctl, there is no need to copy the vcpu number from
userspace and then copy the registers back; the vcpu identity is derived
from the fd used to make the call
Right now the performance benefits are completely theoretical since (a) we
don't support more than one vcpu per VM and (b) virtualization hardware
inefficiencies completely everwhelm any cacheline bouncing effects. But
both of these will change, and we need to prepare the API today.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This reflects the changed scope, from device-wide to single vm (previously
every device open created a virtual machine).
Signed-off-by: Avi Kivity <avi@qumranet.com>
This avoids having filp->f_op and the corresponding inode->i_fop different,
which is a little unorthodox.
The ioctl list is split into two: global kvm ioctls and per-vm ioctls. A new
ioctl, KVM_CREATE_VM, is used to create VMs and return the VM fd.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The kvmfs inodes will represent virtual machines and vcpus, as necessary,
reducing cacheline bouncing due to inodes and filps being shared.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the SVM code to intercept SMIs and handle it
outside the guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This adds a special MSR based hypercall API to KVM. This is to be
used by paravirtual kernels and virtual drivers.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Besides using an established api, this allows using kvm in older kernels.
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The whole thing is rotten, but this allows vmx to boot with the guest reboot
fix.
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We fail to mark a page dirty in three cases:
- setting the accessed bit in a pte
- setting the dirty bit in a pte
- emulating a write into a pagetable
This fix adds the missing cases.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Legacy IDE VLB host drivers didn't check for "probe" options when compiled
as modules, which was obviously wrong as we don't want module to poke at
random I/O ports by simply loading it. Fix it by adding "probe" module param
to legacy IDE VLB host drivers.
v2:
* don't obsolete old "ide0=dtc2278/ht6560b/qd65xx/ali14xx/umc8672"
IDE driver options yet (per Alan Cox's request) and enhance documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove
* "hdx=serialize"
* "idex=noautotune"
* "idex=autotune"
kernel params, they have been obsoleted for ages.
"idex=serialize", "hdx=noautotune" and "hdx=autotune" are still available
so there is no funcionality loss caused by this patch.
v2:
* fix CONFIG_BLK_DEV_4DRIVES=y build broken by version 1 of the patch
[ /me wearing brown paper bag ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 27 February 2007, Akira Iguchi wrote:
>
> But since I sent the first patch, I found a bug for checking DMA IRQ status.
> (http://www.spinics.net/lists/linux-ide/msg06903.html)
> Then I sent the fixed patch for libata only. So my drivers/ide patch
> still has same bug and I want to fix it, too.
>
> The following patch fixes this bug. Please apply this patch.
From: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Revised DRAC4 warning as Jeff suggested, this one includes more info
about why the problem occurs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The change to force legacy mode IDE channels' resources to fixed non-zero
values confuses (at least some versions of) X, because the values reported
by the kernel and those readable from PCI config space aren't consistent
anymore. Therefore, this patch arranges for the respective BARs to also
get updated if possible.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix breakage added in the IDE devel tree.
Add header, then fix
drivers/ide/ppc/pmac.c: In function `pmac_ide_setup_dma':
drivers/ide/ppc/pmac.c:2044: warning: assignment from incompatible pointer type
drivers/ide/ppc/pmac.c: In function `pmac_ide_dma_host_on':
drivers/ide/ppc/pmac.c:1989: warning: control reaches end of non-void function
include/linux/pci.h: In function `pmac_ide_init':
drivers/ide/ppc/pmac.c:1563: warning: ignoring return value of `pci_register_driver', declared with attribute warn_unused_result
Then add some apparently-long-missing error handling.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add CFA devices from I-O Data, Mitsubishi and Viking. Add SanDisk comment.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The tuneproc() method in both these drivers failed to set the drive's own speed.
Fix this by renaming the function and "wrapping around it" the new tuneproc()
method. Switch back to calling tuneproc() in the PIO fallback code.
While at it, also convert the rest of the PIO timing code into proper C. :-)
Has been kind of tested on SLC90E66. I'm too lazy to reboot my box and test
on ICH4... :-)
[ bart: I quickly tested it on ICH4. ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
eighty_ninty_three() had word 93 validitity check but not the 80c bit
test itself (bit 13). This increases the chance of incorrect wire
detection especially because host side cable detection is often
unreliable and we sometimes soley depend on drive side cable
detection. Fix it.
[ bart: fix off-by-1 bit name in the patch description ]
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to cmd64x_tune_pio(), making it return the mode set,
and "wrapping" the new tuneproc() method around it; while at it, also get rid
of the non-working prefetch control code (filtering out related argument values
in the "wrapper"), remove redundant PIO5 mode limitation, make cmdprintk() give
more sensible mode info, and remove mention about the obsolete /proc/ interface.
Get rid of the broken config_chipset_for_pio() which always tried to set PIO4,
switch to always auto-tuning PIO instead.
Oh, and add the missing PIO5 support to the speedproc() method while at it. :-)
Warning: compile tested only -- getting to the real hardware isn't that easy...
On Tuesday 06 February 2007 22:11, Mikael Pettersson <mikpe@it.uu.se> wrote:
>
> Worked fine on my SPARC Ultra5 with a CMD646 IDE controller.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to ali15x3_tune_pio() and "wrapping" the new tuneproc()
method around it and making it return the mode set, update the heading comment.
Also, setting PIO mode via the speedproc() method does not work due to passing
to the tuneproc() method's a mode number not biased by XFER_PIO_0 -- fix this
along with a typo in the heading comment...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This updates the cx88-blackbird driver to be able to use the new cx23416
firmware image released by Hauppauge Computer Works, while retaining
compatibility with the older firmware images.
cx2341x firmware can be downloaded at: http://dl.ivtvdriver.org/ivtv/firmware/
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching HDLC devices from Ethernet-framing mode caused stale ethernet
function assignments within net_device.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current CIPSO engine has a problem where it does not verify that
the given sensitivity level has a valid CIPSO mapping when the "std"
CIPSO DOI type is used. The end result is that bad packets are sent
on the wire which should have never been sent in the first place.
This patch corrects this problem by verifying the sensitivity level
mapping similar to what is done with the category mapping. This patch
also changes the returned error code in this case to -EPERM to better
match what the category mapping verification code returns.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is based on the assumption that an interface's ifindex is basically
an alias for a local MAC address, so incoming packets now are matched
to sockets based on remote MAC, session id, and ifindex of the
interface the packet came in on/the socket was bound to by connect().
For relayed packets, the socket that's used for relaying is selected
based on destination MAC, session ID and the interface index of the
interface whose name currently matches the name requested by userspace
as the relaying source interface.
Signed-off-by: David S. Miller <davem@davemloft.net>
This brings things inline with the sk_acceptq_is_full() bug
fix. The limit test should be x >= sk_max_ack_backlog.
Signed-off-by: David S. Miller <davem@davemloft.net>
when I use linux TCP socket, and find there is a bug in function
sk_acceptq_is_full().
When a new SYN comes, TCP module first checks its validation. If valid,
send SYN,ACK to the client and add the sock to the syn hash table. Next
time if received the valid ACK for SYN,ACK from the client. server will
accept this connection and increase the sk->sk_ack_backlog -- which is
done in function tcp_check_req().We check wether acceptq is full in
function tcp_v4_syn_recv_sock().
Consider an example:
After listen(sockfd, 1) system call, sk->sk_max_ack_backlog is set to
1. As we know, sk->sk_ack_backlog is initialized to 0. Assuming accept()
system call is not invoked now.
1. 1st connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=0 sk->sk_max_ack_backlog=1, function return 0 accept
this connection. Increase the sk->sk_ack_backlog
2. 2nd connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=1 sk->sk_max_ack_backlog=1, function return 0 accept
this connection. Increase the sk->sk_ack_backlog
3. 3rd connection comes. invoke sk_acceptq_is_full(). sk-
>sk_ack_backlog=2 sk->sk_max_ack_backlog=1, function return 1. Refuse
this connection.
I think it has bugs. after listen system call. sk->sk_max_ack_backlog=1
but now it can accept 2 connections.
Signed-off-by: Wei Dong <weid@np.css.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
