This was caught and identified by Greg Onufer.
Since we setup the 256M/4M bitmap table after taking over the trap
table, it's possible for some 4M mapping to get loaded in the TLB
beforhand which later will be 256M mappings.
This can cause illegal TLB multiple-match conditions. Fix this by
setting up the bitmap before we take over the trap table.
Next, __flush_tlb_all() was not doing anything on hypervisor
platforms. Fix by adding sun4v_mmu_demap_all() and calling it.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to mask out the proper bits when testing the dispatch status
register else we can see unrelated NACK bits from previous cross call
sends.
Signed-off-by: David S. Miller <davem@davemloft.net>
get_cpu() always returns zero on non-SMP builds, but we
really want the physical cpu number in this code in order
to do the right thing.
Based upon a non-SMP kernel boot failure report from Bernd Zeimetz.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for possible NULL pointer dereference
if of_find_property() failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There should be a pci_dev_put when breaking out of a loop that iterates
over calls to pci_get_device and similar functions.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't export verify_compat_iovec when CONFIG_NET is
disabled, and consequently the Solaris compat module
should also depend upon CONFIG_NET.
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the MAP_FIXED case is using the wrong address hint. I'd
expect the comment "don't mess with it" means pass the request
straight on through, not change the address requested to -ENOMEM.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
zero out dma_length in the entry immediately following the last mapped
entry for unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
A few trivial Makefile cleanups
- dependencipes in head.o was all wrong - deleted
- CMODEL_CFLAG was not used anywhere
- NEW_GCC was then not used outside sparc64/Makefe - do not export it
- FIXME seems not appropriate - all other put oprofile in drivers-y too
- No reason to do -I. (and it still builds)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke the desc->handle_irq directly in the top-level dispatch,
just like other sophisticated ports.
This will allow us to decrease the cost of the MSI queue dispatch.
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the easiest things to isolate is the pid printed in kernel log.
There was a patch, that made this for arch-independent code, this one makes
so for arch/xxx files.
It took some time to cross-compile it, but hopefully these are all the
printks in arch code.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the largest patch in the set. Make all (I hope) the places where
the pid is shown to or get from user operate on the virtual pids.
The idea is:
- all in-kernel data structures must store either struct pid itself
or the pid's global nr, obtained with pid_nr() call;
- when seeking the task from kernel code with the stored id one
should use find_task_by_pid() call that works with global pids;
- when showing pid's numerical value to the user the virtual one
should be used, but however when one shows task's pid outside this
task's namespace the global one is to be used;
- when getting the pid from userspace one need to consider this as
the virtual one and use appropriate task/pid-searching functions.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: yet nuther build fix]
[akpm@linux-foundation.org: remove unneeded casts]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Paul Menage <menage@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also of_unregister_driver. These will be shortly also used by the
PowerPC code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use *alloc_bootmem_low*(), because ARCH_LOW_ADDRESS_LIMIT
is 4GB and this results in boot failures if all of the physical
memory in the machine is above 4GB.
Signed-off-by: David S. Miller <davem@davemloft.net>
All asm/ipc.h files do only #include <asm-generic/ipc.h>.
This patch therefore removes all include/asm-*/ipc.h files and moves the
contents of include/asm-generic/ipc.h to include/linux/ipc.h.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some time /proc/sys/kernel/core_pattern has been able to set its output
destination as a pipe, allowing a user space helper to receive and
intellegently process a core. This infrastructure however has some
shortcommings which can be enhanced. Specifically:
1) The coredump code in the kernel should ignore RLIMIT_CORE limitation
when core_pattern is a pipe, since file system resources are not being
consumed in this case, unless the user application wishes to save the core,
at which point the app is restricted by usual file system limits and
restrictions.
2) The core_pattern code should be able to parse and pass options to the
user space helper as an argv array. The real core limit of the uid of the
crashing proces should also be passable to the user space helper (since it
is overridden to zero when called).
3) Some miscellaneous bugs need to be cleaned up (specifically the
recognition of a recursive core dump, should the user mode helper itself
crash. Also, the core dump code in the kernel should not wait for the user
mode helper to exit, since the same context is responsible for writing to
the pipe, and a read of the pipe by the user mode helper will result in a
deadlock.
This patch:
Remove the check of RLIMIT_CORE if core_pattern is a pipe. In the event that
core_pattern is a pipe, the entire core will be fed to the user mode helper.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: <martin.pitt@ubuntu.com>
Cc: <wwoods@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch single-linked binfmt formats list to usual list_head's. This leads
to one-liners in register_binfmt() and unregister_binfmt(). The downside
is one pointer more in struct linux_binfmt. This is not a problem, since
the set of registered binfmts on typical box is very small -- (ELF +
something distro enabled for you).
Test-booted, played with executable .txt files, modprobe/rmmod binfmt_misc.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2c941a2040 looks incomplete. The
helper functions like prepare_sg() need to support sg chaining too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Introduce architecture dependent kretprobe blacklists to prohibit users
from inserting return probes on the function in which kprobes can be
inserted but kretprobes can not.
This patch also removes "__kprobes" mark from "__switch_to" on x86_64 and
registers "__switch_to" to the blacklist on x86-64, because that mark is to
prohibit user from inserting only kretprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert cpu_sibling_map from a static array sized by NR_CPUS to a per_cpu
variable. This saves sizeof(cpumask_t) * NR unused cpus. Access is mostly
from startup and CPU HOTPLUG functions.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the sparc64 iommu/pci dma mappers to sg chaining.
Acked-by: David S. Miller <davem@davemloft.net>
Later updated to newer kernel with unified sparc64 iommu sg handling.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It no longer translates to "real irqs" (aka. INO buckets)
so reflect that by using a simpler name for it.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the users go through virt_irq_to_bucket() and essentially
want to go from a virt_irq to an INO, but we have a way
to do that already via virt_to_real_irq_table[].dev_ino.
This also allows us to kill both virt_to_real_irq() and
virt_irq_to_bucket().
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a place to stick INO information in the
virt_to_real_irq_table[], which is currently only used for VIRQs.
And that is readily accessible from the one __irq_ino() call site.
Signed-off-by: David S. Miller <davem@davemloft.net>
We were simply concatenating the devhandle and devino and using that
as the cookie, which defeats the entire purpose of the VIRQ hypervisor
interfaces.
Now that we use physical addresses for the INO buckets, we can
allocate them dynamically for VIRQs and encode the cookies as
~__pa(bucket). This allows us to test for and decode the cookie with
a simple:
brlz $reg1, 1f
xnor $reg1, %g0, $reg2
sequence.
This works because bit 64 is never set in traditional
INO vectors, and it is also never set in a physical
address. So xnor'ing the physical address of the bucket
always gives us a negative number, and thus a unique
condition we can test cheaply.
Inspired by ideas from Greg Onufer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we chain IVEC entries using 32-bit "pointers"
because we know that the ivector_table is in the main
kernel image, thus below 4GB.
This uses proper 64-bit pointers instead.
Whilst this bloats up the kernel image size, this sets
the infrastructure necessary to significantly shrink the
kernel size by using physical addresses and dynamically
allocating the ivector table.
Signed-off-by: David S. Miller <davem@davemloft.net>
This also makes us use the MSI queues correctly.
Each MSI queue is serviced by a normal sun4u/sun4v INO interrupt
handler. This handler runs the MSI queue and dispatches the
virtual interrupts indicated by arriving MSIs in that MSI queue.
All of the common logic is placed in pci_msi.c, with callbacks to
handle the PCI controller specific aspects of the operations.
This common infrastructure will make it much easier to add MSG
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer initialise the name field of the of_platform_driver, but
use the name field of the embedded device_driver's name field instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Tom Callaway for the excellent bug report and
test case.
sys_ipc() has several problems, most to due with semaphore
call handling:
1) 'err' return should be a 'long'
2) "union semun" is passed in a register on 64-bit compared
to 32-bit which provides it on the stack and therefore
by reference
3) Second and third arguments to SEMCTL are swapped compared
to 32-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
The name field of of_platform_driver is just copied into the
included device_driver. By not overriding an already initialised
device_driver name, we can convert the drivers over time to stop using
the of_platform_driver name.
Also we were not copying the owner field from of_platform_driver, so do
the same with it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply a consistent format to vmlinux.lds.
The file is now to some degree readable.
In addition move several labels inside the braces
such that they reflect the actual start address of a section.
Without this the label would not reflect if ld added alignment.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support code is identical to the hypervisor sun4v stuff,
just replacing the hypervisor calls with register reads and
writes in the Fire controller.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Check the return value of fork_idle() to catch error.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI-E slot on T1000 connects directly to the Fire PCI chip with no
intervening bridges visible in the OBP tree.
Unfortunately the bus numbering of the device in that slot is
different (2) from the PCI host controller (0), and thus the
pci_bus_{read,write}_config_*() calls don't work out.
Complicating things further the Fire PCI controller has no config
space it responds to either.
For now treat this case specially so that devices in the slot work.
Longer term we need to perhaps cons up a dummy bridge between the Fire
and the PCI-E slot so that the bus hierarchy is complete inside of the
kernel and thus the bus numbering all works out right.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should only use ports underneath "domain-services", other DS ports
in the MDESC aren't for us to use.
Signed-off-by: David S. Miller <davem@davemloft.net>
argv and envp are pointers to u32's in userspace, so don't
try to put_user() a NULL to them.
Aparently gcc-4.2.x now warns about this, and since we use
-Werror for arch/sparc64 code, this breaks the build.
Signed-off-by: David S. Miller <davem@davemloft.net>
If of_get_property() fails, it returns NULL and the 'len'
parameter is undefined. So we need to explicitly set len
to zero in such cases.
Noticed by Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
When NR_CPUS is smaller than the cpu probed, let the user
know that the cpu won't be used.
Suggested by Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Al Viro, when we try to call prom_set_trap_table()
in the SMP trampoline code we try to take the PROM call spinlock
which doesn't work because the current thread pointer isn't
valid yet and lockdep depends upon that being correct.
Furthermore, we cannot set the current thread pointer register
because it can't be properly dereferenced until we return from
prom_set_trap_table(). Kernel TLB misses only work after that
call.
So do the PROM call to set the trap table directly instead of
going through the OBP library C code, and thus avoid the lock
altogether.
These calls are guarenteed to be serialized fully.
Since there are now no calls to the prom_set_trap_table{_sun4v}()
library functions, they can be deleted.
Signed-off-by: David S. Miller <davem@davemloft.net>
On the root PCI bus, the OBP device tree lists device 3 twice.
Once as 'pm' and once as 'lomp'.
Everything goes downhill from there.
Ignore the second instance to workaround this.
Thanks to Kövedi_Krisztián for the bug report and
testing the fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) sun4{u,v}_build_msi() have improper return value handling.
We should always return negative error codes, instead of
using the magic value "0" which could in fact be a valid
MSI number.
2) sun4{u,v}_build_msi() should return -ENOMEM instead of
calling prom_prom() halt with kzalloc() of the interrupt
data fails.
3) We 'remembered' the MSI number using a singleton in the
struct device archdata area, this doesn't work for MSI-X
which can cause multiple MSIs assosciated with one device.
Delete that archdata member, and instead store the MSI
number in the IRQ chip data area.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes we were using 32-bit values and the top bits were
getting inadvertantly chopped off. This will matter for the
forthcoming Fire controller MSI support.
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is not a part of the sun4v architecture.
Niagara 1 and 2 happened to leave it around.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the OF device tree, it's useful to let userland get
at the machine description so it can pretty print the
graph etc.
The implementation is a simple MISC device with a read method.
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time a cpu is added via hotplug, we allocate the per-cpu MONDO
queues but we never free them up. Freeing isn't easy since the first
cpu gets this memory from bootmem.
Therefore, the simplest thing to do to fix this bug is to allocate the
queues for all possible cpus at boot time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the cpu type in the OBP device tree before committing to
using the optimized Niagara memcpy and memset implementation.
If we don't recognize the cpu type, use a completely generic
version.
Signed-off-by: David S. Miller <davem@davemloft.net>
It didn't handle that case at all, and now dump_stack()
can be implemented directly as show_stack(current, NULL)
Signed-off-by: David S. Miller <davem@davemloft.net>
Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.
Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.
Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.
This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't provide fake PCI config space for sun4u.
Also, put back the funny host controller space handling that
at least Sabre needs. You have to read PCI host controller
registers at their nature size otherwise you get zeros instead
of correct values.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't mark the whole thing init because there are dependencies
in bootloaders that assume that _start, or whatever the image
entry value, is 2 instructions before the "HdrS" signature.
In fact, TILO assumes this entry is always at 0x4000, yikes!
Also, right after the bootloader info area there are OBP strings and
values that get used later in the boot process, and those are not all
provably .init yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes boot failures when the build-id LD option is
actually used, because without it we end up with multiple
PT_LOAD sections which the SILO boot loader cannot handle.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: ERROR: "sys_ioctl" [arch/sparc64/solaris/solaris.ko] undefined!
[SPARC32]: Make PAGE_SHARED a read-mostly variable.
[SPARC32]: Take enable_irq/disable_irq out of line.
[SPARC32]: clean include/asm-sparc/irq.h
[SPARC32]: Fix rounding errors in ndelay/udelay implementation.
From: Christoph Hellwig <hch@infradead.org>
On Fri, Jul 20, 2007 at 09:24:42AM -0400, Horst H. von Brand wrote:
> When building v2.6.22-3478-g275afca on sparc64 (.config attached) I get:
>
> MODPOST vmlinux
> Building modules, stage 2.
> MODPOST 463 modules
> ERROR: "sys_ioctl" [arch/sparc64/solaris/solaris.ko] undefined!
Sorry, my fault.
It looked to me like sparc64 exports sys_ioctl on it's own, but it
only exports compat_sys_ioctl on it's own.
Signed-off-by: David S. Miller <davem@davemloft.net>
i386 and sparc64 have the identical code to update the cmos clock. Move it
into kernel/time/ntp.c as there are other architectures coming along with the
same requirements.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: David Miller <davem@davemloft.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.
[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: vmlinux.o(.text+0x35264): Section mismatch: reference to .init.text:__alloc_bootmem (between 'mdesc_bootmem_alloc' and 'mdesc_bootmem_free')
Rename mdesc_mem_ops to *_ops so modpost ignores __init references
and declare mdesc_bootmem_alloc __init since it is only used
during __init context.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warning:
WARNING: vmlinux.o(.text+0x3cf50): Section mismatch: reference to .init.text:page_in_phys_avail (between 'pci_sun4v_pbm_init' and 'sun4v_pci_init')
pci_sun4v_pbm_init and sun4v_pci_init was only used under __init
context so declare them _init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing sparc64 mini_rtc driver can handle CMOS based
rtcs trivially with just a few lines of code and the simplifies
things tremendously.
Tested on SB1500.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_handle and dev_ino fields don't match up exactly to
the traditional IMAP_IGN and IMAP_INO masks.
So store them away in a table and look them up directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
When booting up a control node it's quite common to
not be able to register several service types.
And likewise on guests at least one or two are going
to not be there.
Signed-off-by: David S. Miller <davem@davemloft.net>
The best scheme to get uniqueness seems to be:
FOO -- If node lacks "id" property
FOO-$(ID) -- If node has "id" but parent lacks "cfg-handle"
FOO-$(ID)-$(CFG_HANDLE) -- If node has both
Signed-off-by: David S. Miller <davem@davemloft.net>
The current scheme works on static interpretation of text names, which
is wrong.
The output-device setting, for example, must be resolved via an alias
or similar to a full path name to the console device.
Paths also contain an optional set of 'options', which starts with a
colon at the end of the path. The option area is used to specify
which of two serial ports ('a' or 'b') the path refers to when a
device node drives multiple ports. 'a' is assumed if the option
specification is missing.
This was caught by the UltraSPARC-T1 simulator. The 'output-device'
property was set to 'ttya' and we didn't pick upon the fact that this
is an OBP alias set to '/virtual-devices/console'. Instead we saw it
as the first serial console device, instead of the hypervisor console.
The infrastructure is now there to take advantage of this to resolve
the console correctly even in multi-head situations in fbcon too.
Thanks to Greg Onufer for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/ofcons:
Create drivers/of/platform.c
Create linux/of_platorm.h
[SPARC/64] Rename some functions like PowerPC
Begin consolidation of of_device.h
Begin to consolidate of_device.c
Consolidate of_find_node_by routines
Consolidate of_get_next_child
Consolidate of_get_parent
Consolidate of_find_property
Consolidate of_device_is_compatible
Start split out of common open firmware code
Split out common parts of prom.h
