I noticed this driver (and several others) reinvent their own copy of the
existing CRC library. Don't have the hardware, but tested by extracting
code and comparing result.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If using Message Signaled Interrupts (MSI) then the IRQ will never
be shared. Don't call pci_disable_msi() unless using MSI.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is possible for the sky2 driver NAPI poll routine to be called with
IRQ's disabled if netpoll is trying to make space in the tx queue. This
is an obscure path, but if it happens, the kfree_skb needs to happen
via softirq. Calling kfree_skb with IRQ's disabled is a not allowed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update workarounds for 88E803X based on the latest SysKonnect vendor
driver version (8.41). Tested on EC_U rev A1, only.
These up the receive performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add new PCI ID for DLink 560SX.
This from the latest SysKonnect vendor driver (version 8.41).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If sky2 detects out of memory, or gets a bad frame, it reuses the same receive
buffer, but forgets to poke the hardware. This could lead to the receiver
getting stuck if there were lots of errors.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I would rather fix Andy's problem by not clearing
multicast information on link down.
Also, add code to restore multicast state after ethtool phy reset.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/built-in.o: In function `netxen_nic_remove':
netxen_nic_main.c:(.text+0x31b4d): undefined reference to `pci_disable_msi'
netxen_nic_main.c:(.text+0x31b8e): undefined reference to `pci_release_regions'
drivers/built-in.o: In function `netxen_init_module':
netxen_nic_main.c:(.init.text+0x3f17): undefined reference to `pci_module_init'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chelsio driver can use __netif_rx_schedule_prep instead of it's own
test_and_set inline. Applies after the previous 4 patches.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Network devices need to be free'd with free_netdev() not kfree()
otherwise the kernel will panic if an application has /sys/class/net/ethX/value
open and reads it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Complete removal of proc stuff from chelsio. The orignal driver had a debug
proc interface, but not all the code got removed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whitespace cleanups. Replace leading spaces with tabs and fix indentation
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chelsio network driver has some extra ifdef's that got in because the
driver was originally based on code that worked on 2.4 as well as 2.6.
This patch removes the dead code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Include of_platform header, and use
new of_[un]register_platform_driver() fns.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use NULL instead of 0 for pointers (cures sparse warnings).
drivers/net/sundance.c:1106:16: warning: Using plain integer as NULL pointer
drivers/net/sundance.c:1652:16: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bcm43xx and ipw2100 currently duplicate the same simplistic get_stats
handler. Additionally, zd1211rw requires the same handler to fix a
bug where all stats are reported as 0.
This patch adds a generic implementation to the ieee80211 layer,
which drivers are free to override.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds zd1211rw driver support for the softmac functionality I
added a while back. We now obey changes in basic rates, use short
preamble if it is available (but long if the AP says it's not),
and send self-CTS in the proper situations.
Locking fixed and improved by Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These controlset rate constants are also applicable in places outside
the controlset, such as in the RTS/CTS control register.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Goff found that he could not use his ZD1211 device which is
programmed for the Japan regulatory domain. It turns out that ZyDAS
deviate from the spec here: they do not use the newer Japan region code
(0x41) but their drivers do operate as if the newer Japan legal
frequency range is in effect.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a high number of split USB transactions, which contain
only one packet but have a length info field. This patch optimizes
this code by stopping parsing the length info structure if a zero
length field is encountered.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit-field constants in zd_chip.h are now defined using a shift expression.
The value 0x08 is now (1 << 3). The fix is intended to improve readability.
Remove misleading comment in zd_mac.c: The function already returns -EPERM
in managed mode (IW_MODE_INFRA).
Remove unused code in zd_mac.c: The unused code intended for debugging
rx_status values is no longer useful.
Added dump_stack() to ZD_ASSERT macro: Output of the stack helps to debug
assertions. Keep in mind that the ZD_ASSERT() macro only results in code,
if DEBUG is defined.
Improved comments for filter_rx()
zd_usb.c: Added driver name to module init and exit functions
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
http://bugzilla.kernel.org/show_bug.cgi?id=7399
zd1211rw's support for IW_FREQ_AUTO is broken: when specified, the driver
tries to change to a channel specified in an uninitialized integer. As
IW_FREQ_AUTO is hard to implement properly, the solution (at least for now)
is to drop support for it and start ignoring the flags like all other wireless
drivers do.
This has the added advantage that kismet also starts working with zd1211rw,
even though kismet requesting IW_FREQ_AUTO is also a bug (fixed in their svn)
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211b chip 050d:705c v4810 high 00-17-3f AL2230_RF pa0 g--N
Tested by Bryan Barnard
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211 chip 14ea:ab13 v4330 high 00-90-cc AL2230_RF pa0 g---
Tested by Tetsuya Yatagai.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the patch sent by Daniel Drake under the title "[PATCH] ieee80211: Move
IV/ICV stripping into ieee80211_rx", a needed line was accidentally removed.
(NOTE: I'm pretty sure this was my fault, not Daniel's. -- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver for the Atmel MACB on-chip ethernet module.
Tested on AVR32/AT32AP7000/ATSTK1000. I've heard rumours that it works
with AT91SAM9260 as well, and it may be possible to share some code with
the at91_ether driver for AT91RM9200.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since previous version:
* Probe for PHY ID instead of depending on it being provided through
platform_data.
* Grab initial ethernet address from the MACB registers instead
of depending on platform_data.
* Set MII/RMII mode correctly.
These changes are mostly about making the driver more compatible with
the at91 infrastructure.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Another thing, reported recently to me by several people - DSCC4 WAN
driver now (and perhaps for the last couple of years+) requires the
generic HDLC. I've fixed the Kconfig and moved the DSCC4 option
under CONFIG_HDLC so it's consistent visually.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add tsi108/9 on chip Ethernet controller driver support.
The driver code collects the feedback of previous posting form the mailing
list and gives the update.
MPC7448HPC2 platform in arch/powerpc uses tsi108 bridge.
The following is a brief description of the Ethernet controller:
The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to
manage the two physical connection devices (PHYs). Each Ethernet port has
its own statistics monitor that tracks and reports key interface
statistics. Each port supports a 256-entry hash table for address
filtering. In addition, each port is bridged to the Switch Fabric through
a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows. The Ethernet DMA channels use
descriptors set up in memory, the memory map of the device, and access via
the Switch Fabric. The Ethernet Controller’s DMA arbiter handles
arbitration for the Switch Fabric. The Controller also has a register bus
interface for register accesses and status monitor control.
The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each
Ethernet port uses its transmit and receive DMA channels to manage data
flows through buffer descriptors that are predefined by the system (the
descriptors can exist anywhere in the system memory map). These
descriptors are data structures that point to buffers filled with data
ready to transmit over Ethernet, or they point to empty buffers ready to
receive data from Ethernet.
Signed-off-by: Alexandre Bounine <Alexandre.Bounine@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Solve host error problem in low performance embedded system when continune
down and up. It will cause IP100A DMA TargetAbort. So we need more safe
process to up and down IP100A with wait hardware completely stop and software
cur_tx/ dirty_tx/cur_task/last_tx be clear.
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ia64:
drivers/built-in.o(.text+0xd9a72): In function `e1000_xmit_frame':
: undefined reference to `csum_ipv6_magic'
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch requires the new support for configurable PHY
interfaces.
Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean-up some warnings from missing return code checks, mostly from
calling pci_enable_device during a PCI resume.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the softmac version of bcm43xx, the core scan logs whether each core is
enabled or disabled. This information is useless as one of the next steps
is to enable all cores. This patch removes this output from the log.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the periodic work function in bcm43xx was converted for voluntary preemption
to reduce latency, a new function was created to estimate the "badness" of
each step, and this quantity was used to determine if preemption should be
enabled when periodic work was undertaken. This concept was quite useful
while debugging of periodic work was in progress. Now that this routine
seems to be working correctly, it is time to simplify the code. This
patch keeps the functionality intact, but simplifies the code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct initial and close hardware step. In some embedded system down and up
IP100A will cause DMA crash. We add some for safe down and up IP100A.
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* genphy_update_link is now exported
* Added a fix from ncase@xes-inc.com which changes forcing so it
only updates the link. Otherwise, it never tries the lower
values, since it is always overwriting the speed/duplex values
with the current ones, rather than the intended ones.
* Fixed a bug where bringing up a PHY with no link caused it to
timeout, and enter forcing mode. Once in forcing mode,
plugging in the link didn't autonegotiate. Now the AN state
detects the lack of link, and enters the NO_LINK state. AN
only times out if the link is up and AN fails
* Cleaned up the PHY_AN case, reducing one level of indentation
for the timeout code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix TX Pause bug (reset_tx, intr_handler). When MaxCollisions occurred, need
to re-enable Tx. But just after re-enable, MaxCollisions maybe occurred again
and with TxStatusOverflow. This will cause driver can't check new
MaxCollisions to re-enable Tx again, because TxStatusOverflow. For this
reason, after re-enable Tx, we need to make sure Tx was actually enabled.
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For patent issue need to remove TxStartThresh and RxEarlyThresh. This patent
is cut-through patent. If use this function, Tx will start to transmit after
few data be move in to Tx FIFO. We are not allow to use those function in
DFE530/DFE550/DFE580/DL10050/IP100/IP100A. It will decrease a little
performance.
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the code to change the E8390_CMD register from ei_watchdog().
The 8390-page is always 0 outside the spin_lock.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the new mcp67 device into forcedeth.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support to recover from a previously fatal MAC error. In
the past the MAC would be hung on an internal fatal error. On new
chipsets, the MAC has the ability to enter a non-fatal state and allow
the driver to re-init it.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the mgmt unit in certain chipsets. The MAC
and the mgmt unit share the PHY and therefore proper intialization
procedures are needed for them to maintain coexistense.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PDQ DMA engine requires a different byte-swapping mode for big-endian
hosts; also the MAC address which is read from a register through PIO has
to be byte-swapped. These changes have been verified with DEFPA-DC (PCI)
boards and a Broadcom BCM91250A (MIPS CPU based) host.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
replace open coded kmemdup() to save some screen space,
and allow inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Realtek's 8139/810x (0x8136) PCI-E comes with a touchy PHY.
A big heavy reset seems to calm it down.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7378.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Add a new dynamic itr algorithm, with 2 modes, and make it the default
operation mode. This greatly reduces latency and increases small packet
performance, at the "cost" of some CPU utilization. Bulk traffic
throughput is unaffected.
The driver can limit the amount of interrupts per second that the
adapter will generate for incoming packets. It does this by writing a
value to the adapter that is based on the maximum amount of interrupts
that the adapter will generate per second.
Setting InterruptThrottleRate to a value greater or equal to 100 will
program the adapter to send out a maximum of that many interrupts per
second, even if more packets have come in. This reduces interrupt
load on the system and can lower CPU utilization under heavy load,
but will increase latency as packets are not processed as quickly.
The default behaviour of the driver previously assumed a static
InterruptThrottleRate value of 8000, providing a good fallback value
for all traffic types,but lacking in small packet performance and
latency. The hardware can handle many more small packets per second
however, and for this reason an adaptive interrupt moderation algorithm
was implemented.
Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in
which it dynamically adjusts the InterruptThrottleRate value based on
the traffic that it receives. After determining the type of incoming
traffic in the last timeframe, it will adjust the InterruptThrottleRate
to an appropriate value for that traffic.
The algorithm classifies the incoming traffic every interval into
classes. Once the class is determined, the InterruptThrottleRate
value is adjusted to suit that traffic type the best. There are
three classes defined: "Bulk traffic", for large amounts of packets
of normal size; "Low latency", for small amounts of traffic and/or
a significant percentage of small packets; and "Lowest latency",
for almost completely small packets or minimal traffic.
In dynamic conservative mode, the InterruptThrottleRate value is
set to 4000 for traffic that falls in class "Bulk traffic". If
traffic falls in the "Low latency" or "Lowest latency" class, the
InterruptThrottleRate is increased stepwise to 20000. This default
mode is suitable for most applications.
For situations where low latency is vital such as cluster or
grid computing, the algorithm can reduce latency even more when
InterruptThrottleRate is set to mode 1. In this mode, which operates
the same as mode 3, the InterruptThrottleRate will be increased
stepwise to 70000 for traffic in class "Lowest latency".
Setting InterruptThrottleRate to 0 turns off any interrupt moderation
and may improve small packet latency, but is generally not suitable
for bulk throughput traffic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add a generic MSI interrupt routine that is IO read-free, speeding up
MSI interrupt handling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This file needs some cleanups and reordering - logically order it
so that relevant defines and code are together with properly quoted
defaults.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Spec fix: don't set IDE unless we are actually setting the tx
int delay time.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
ICH8 will soon be followed by newer chipsets bearing the same acronym,
thus we remove the '8' and make it independent of the version number in
the platform name.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add a netif_wake/start_queue counter to the ethtool statistics to indicated
to the user that their transmit ring could be too small for their workload.
Signed-off-by: Jesse brandeburg <jesse.brandeburg@intel.com>
Cc: Jamal Hadi <hadi@cyberus.ca>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add support for a Low Profile quad-port PCI-E adapter and 2 variants
of the ICH8 systems' onboard NIC's.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This memsetting was added in a paranoid rage debugging TX hangs, but
are no longer of importance. We can beef up the performance quite a
bit removing them. Make sure to fill in next_to_watch to allow this.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Order pci-e capability struct according to bus/pci bus width ordering
preserving the hard pci spec numbers.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On ich systems during PHY power down to D3, the voltage regulators
were left on.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IA64 SMP systems were seeing TX issues with multiple cpu's attempting
to write tail registers unordered. This mmiowb() fixes the issue.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Enable early receives on 82573 for jumbo frame performance. Jumbo's
are only supported on 82573L with ASPM disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Enable TSO for IPV6. All e1000 hardware supports it. This reduces CPU
utilizations by 50% when transmitting IPv6 frames.
Fix symbol naming enabling ipv6 TSO. Turn off TSO6 for 10/100.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove debugging code disabling MULR (multiple reads). It's not usable
for a wide audience and there are no known problems with MULR right
now.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Tested by Newsome on IRC
zd1211 chip 0586:3401 v4330 high 00-13-49 AL2230_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bcm43xx driver does not contain code to handle PCI-E interfaces
such as the BCM4311 and BCM4312. This patch, originally written by Stefano
Brivio adds the necessary code to enable these interfaces.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Output signal strength information as part of iwlist scan - before it did
not output any signal strength related information.
Signed-off-by: Holden Karau <holden@pigscanfly.ca>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NET: prism54 - fix potential race in reset scheduling
There appears to be a race in reset scheduling logic - thread
responsible for reseting the interface should clear "reset
pending" flag before restarting the queue, otherwise timeout
handler might not schedule another reset even if it is needed.
This race is mostly theoretical as far as I can see but a race
nonetheless.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NET: atmel - do not initialize array over and over again
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a host_strip_iv_icv flag to ieee80211 which indicates that
ieee80211_rx should strip the IV/ICV/other security features from the payload.
This saves on some memmove() calls in the driver and seems like something that
belongs in the stack as it can be used by bcm43xx, ipw2200, and zd1211rw
I will submit the ipw2200 patch separately as it needs testing.
This patch also adds some sensible variable reuse (idx vs keyidx) in
ieee80211_rx
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bcm43xx-softmac driver fails to set two quantities needed for
iwlist to compute wireless quality when scanning. As a result, userland
programs using the quality to determine the best connection fail.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rest of 8390 conversions; ifdef cascade in 8390.h is gone now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
more 8390 conversions - mac8390, zorro8390 and hydra got the same treatment
as arm etherh; one more case in 8390.h ifdef cascade is gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
etherh and a handful of other odd drivers use different macros when building
8390.c. Since we generate a single 8390.o and then link with it, in any
config with both oddball and normal 8390-based driver we will end up with
breakage in at least one of them. Solution: take most of 8390.c into
lib8390.c and have 8390.c, etherh.c and the rest of oddballs #include it.
Helper macros are taken from 8390.h to whoever includes lib8390.c. That
way odd drivers get separate instances of compiled 8390 stuff and stop
stepping on each other's toes. 8390.h gets cleaned up - we don't have
the cascade of ifdefs in there and are left with the stuff that can be
used by any 8390-based driver. Current problems are exactly because of
that cascade - we attempt to choose the set of helpers by looking at config
and that, of course, doesn't work well when we have several sets needed
by various drivers in our config.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add MII ioctl support to the deprecated sk98lin driver.
This allows comparison with skge driver's PHY settings.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for dumping the registers in the deprecated
sk98lin driver. This is allows for easier comparison with
settings in new skge driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_module_init() convertion in olympic.c
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was spotted by coverity (cid #793). All callers dereference dev
before calling this functions, and we dereference it earlier in the
function, when initializing lp.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tobias Diedrich <ranma@tdiedrich.de> sayeth:
Vanilla forcedeth doesn't seem to support suspend and an ifdown/up-cycle is
needed to get it working again after suspend. Francois Romieu's "Awfully
experimental" patch is working just fine for me (with message signalled
interrupts disabled) and has survived quite a few suspend/resume cycles.
So I'd very much like to see (at least partial, with msi disabled)
suspend support for forcedeth in mainline.
(Addresses http://bugzilla.kernel.org/show_bug.cgi?id=6398)
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc; Jeff Garzik <jeff@garzik.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a couple of problems discovered with interrupt handling
in the phylib core, namely:
1. The driver uses timer and workqueue calls, but does not include
<linux/timer.h> nor <linux/workqueue.h>.
2. The driver uses schedule_work() for handling interrupts, but does not
make sure any pending work scheduled thus has been completed before
driver's structures get freed from memory. This is especially
important as interrupts may keep arriving if the line is shared with
another PHY.
The solution is to ignore phy_interrupt() calls if the reported device
has already been halted and calling flush_scheduled_work() from
phy_stop_interrupts() (but guarded with current_is_keventd() in case
the function has been called through keventd from the MAC device's
close call to avoid a deadlock on the netlink lock).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
patch-mips-2.6.18-20060920-phy-irq-16
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for interrupt-driven operation of the Broadcom
Gigabit Ethernet PHYs. I have included device IDs for the parts used on
Broadcom SiByte evaluation boards; more can be added as a need arises.
They are apparently generally software-compatible with one another.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
patch-mips-2.6.18-20060920-broadcom-phy-15
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[PATCH] Fix an offset error when reading the CS89x0 ADD_PORT register
[PATCH] spidernet: poor network performance
[PATCH] Spidernet: remove ETH_ZLEN check in earlier patch
[PATCH] bonding: fix an oops when slave device does not provide get_stats
[PATCH] drivers/net: SAA9730: Fix build error
Revert "[PATCH] zd1211rw: Removed unneeded packed attributes"
[PATCH] zd1211rw: Fix of a locking bug
[PATCH] softmac: remove netif_tx_disable when scanning
[PATCH] ieee80211: Fix kernel panic when QoS is enabled
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
usbcore: remove unused argument in autosuspend
USB: keep count of unsuspended children
USB hub: simplify remote-wakeup handling
USB: struct usb_device: change flag to bitflag
OHCI: make autostop conditional on CONFIG_PM
USB: Add autosuspend support to the hub driver
EHCI: Fix root-hub and port suspend/resume problems
USB: create a new thread for every USB device found during the probe sequence
USB: add driver for the USB debug devices
USB: added dynamic major number for USB endpoints
USB: pegasus error path not resetting task's state
USB: endianness fix for asix.c
USB: build the appledisplay driver
USB serial: replace kmalloc+memset with kzalloc
USB: hid-core: canonical defines for Apple USB device IDs
USB: idmouse cleanup
USB: make drivers/usb/core/driver.c:usb_device_match() static
USB: lh7a40x_udc remove double declaration
USB: pxa2xx_udc recognizes ixp425 rev b0 chip
usbtouchscreen: add support for DMC TSC-10/25 devices
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
Driver core: show drivers in /sys/module/
Documentation/driver-model/platform.txt update/rewrite
Driver core: platform_driver_probe(), can save codespace
driver core: Use klist_remove() in device_move()
driver core: Introduce device_move(): move a device to a new parent.
Driver core: make drivers/base/core.c:setup_parent() static
driver core: Introduce device_find_child().
sysfs: sysfs_write_file() writes zero terminated data
cpu topology: consider sysfs_create_group return value
Driver core: Call platform_notify_remove later
ACPI: Change ACPI to use dev_archdata instead of firmware_data
Driver core: add dev_archdata to struct device
Driver core: convert sound core to use struct device
Driver core: change mem class_devices to be real devices
Driver core: convert fb code to use struct device
Driver core: convert firmware code to use struct device
Driver core: convert mmc code to use struct device
Driver core: convert ppdev code to use struct device
Driver core: convert PPP code to use struct device
Driver core: convert cpuid code to use struct device
...
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
