SH_MPC1211 has been marked as BROKEN for some time.
Unless someone is working on reviving it now, I'd therefore suggest this
patch to remove it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Sparc doesn't have some of the OF interfaces this driver
wants to use.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (27 commits)
pata_atiixp: Don't disable
sata_inic162x: update intro comment, up the version and drop EXPERIMENTAL
sata_inic162x: add cardbus support
sata_inic162x: kill now unused SFF related stuff
sata_inic162x: use IDMA for ATAPI commands
sata_inic162x: use IDMA for non DMA ATA commands
sata_inic162x: kill now unused bmdma related stuff
sata_inic162x: use IDMA for ATA_PROT_DMA
sata_inic162x: update TF read handling
sata_inic162x: add / update constants
sata_inic162x: misc clean ups
sata_mv use hweight16() for bit counting (V2)
sata_mv NCQ-EH for FIS-based switching
sata_mv delayed eh handling
libata: export ata_eh_analyze_ncq_error
sata_mv new mv_port_intr function
sata_mv fix mv_host_intr bug for hc_irq_cause
sata_mv NCQ and SError fixes for mv_err_intr
sata_mv rearrange mv_config_fbs
sata_mv errata workaround for sata25 part 1
...
A couple of distributions (Fedora, Ubuntu) were having weird problems with the
ATI IXP series PATA controllers being reported as simplex. At the heart of
the problem is that both distros ignored the recommendations to load pata_acpi
and ata_generic *AFTER* specific host drivers.
The underlying cause however is that if you D3 and then D0 an ATI IXP it
helpfully throws away some configuration and won't let you rewrite it.
Add checks to ata_generic and pata_acpi to pin ATIIXP devices. Possibly the
real answer here is to quirk them and pin them, but right now we can't do that
before they've been pcim_enable()'d by a driver.
I'm indebted to David Gero for this. His bug report not only reported the
problem but identified the cause correctly and he had tested the right values
to prove what was going on
[If you backport this for 2.6.24 you will need to pull in the 2.6.25
removal of the bogus WARN_ON() in pcim_enagle]
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: David Gero <davidg@havidave.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x is now ready for production use. Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When attached to cardbus, mmio region is at BAR 1. Other than that,
everything else is the same. Add support for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x now doesn't use any SFF features. Remove all SFF
related stuff.
* Mask unsolicited ATA interrupts. This removes our primary source of
spurious interrupts and spurious interrupt handling can be tightened
up. There's no need to clear ATA interrupts by reading status
register either.
* Don't dance with IDMA_CTL_ATA_NIEN and simplify accesses to
IDMA_CTL.
* Inherit from sata_port_ops instead of ata_sff_port_ops.
* Don't initialize or use ioaddr. There's no need to map BAR0-4
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for ATAPI commands. Write and some misc commands time out
when executed using ATAPI_PROT_DMA but ATAPI_PROT_PIO works fine. As
PIO is driven by DMA too, it doesn't make any noticeable difference
for native SATA devices. inic_check_atapi_dma() is implemented to
force PIO for those ATAPI commands.
After this change, sata_inic162x issues all commands using IDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for PIO and non-data commands. This allows sata_inic162x to
safely drive LBA48 devices. Kill inic_dev_config() which contains
code to reject LBA48 devices.
With this change, status checking in inic_qc_issue() to avoid hard
lock up after hotplug can go away too.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The modified driver on initio site has enough clue on how to use IDMA.
Use IDMA for ATA_PROT_DMA.
* LBA48 now works as long as it uses DMA (LBA48 devices still aren't
allowed as it can destroy data if PIO is used for any reason).
* No need to mask IRQs for read DMAs as IDMA_DONE is properly raised
after transfer to memory is actually completed. There will be some
spurious interrupts but host_intr will handle it correctly and
manipulating port IRQ mask interacts badly with the other port for
some reason, so command type dependent port IRQ masking is not used
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
inic162x can't reliably read back TF or at least we don't know how to
do it yet. The only values which seem reliable are status and error.
This patch updates access to TF.
* implement inic_tf_read() which reads the TF area in mmio area
* implement custom inic_qc_fill_rtf() which only returns true if
status indicates device error. it'll be returning bogus addresses
for device errors but it'll be able to report why it failed at
least.
* implement custom inic_check_ready() and use ata_wait_after_reset()
instead of the SFF version.
* use inic_tf_read() for classification.
This is not perfect but it fixes hotplug detection failure and at
least makes the driver report 0's instead of random garbages while
reporting valid status and error for device errors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* add a bunch of constants, most are from the datasheet, a few
undocumented ones are from initio's modified driver
* HCTL_PWRDWN is bit 12 not 13
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* use larger indents for structure member definitions
* kill unused variable @addr in inic_scr_write()
* kill unnecessary flushes in inic_freeze/thaw()
* kill buggy explicit kfree() on devres managed port private data
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some tidying as suggested by Grant Grundler.
Nuke local bit-counting function from sata_mv in favour of using hweight16().
Also add a short explanation for the 15msec timeout used when waiting for empty/idle.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert sata_mv's EH for FIS-based switching (FBS) over to the
sequence recommended by Marvell. This enables us to catch/analyze
multiple failed links on a port-multiplier when using NCQ.
To do this, we clear the ERR_DEV bit in the EDMA Halt-Conditions register,
so that the EDMA engine doesn't self-disable on the first NCQ error.
Our EH code sets the MV_PP_FLAG_DELAYED_EH flag to prevent new commands
being queued while we await completion of all outstanding NCQ commands
on all links of the failed PM.
The SATA Test Control register tells us which links have failed,
so we must only wait for any other active links to finish up
before we stop the EDMA and run the .error_handler afterward.
The patch also includes skeleton code for handling of non-NCQ FBS operation.
This is more for documentation purposes right now, as that mode is not yet
enabled in sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce a new "delayed error handling" mechanism in sata_mv,
to enable us to eventually deal with multiple simultaneous NCQ
failures on a single host link when a PM is present.
This involves a port flag (MV_PP_FLAG_DELAYED_EH) to prevent new
commands being queued, and a pmp bitmap to indicate which pmp links
had NCQ errors.
The new mv_pmp_error_handler() uses those values to invoke
ata_eh_analyze_ncq_error() on each failed link, prior to freezing
the port and passing control to sata_pmp_error_handler().
This is based upon a strategy suggested by Tejun.
For now, we just implement the delayed mechanism.
The next patch in this series will add the multiple-NCQ EH code
to take advantage of it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out the inner loop body of mv_host_intr()
into it's own function called mv_port_intr().
This should help maintainabilty.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unwanted reads of hc_irq_cause from mv_host_intr(),
thereby removing a bug whereby we were not always reading it when needed..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sigh. Undo some earlier changes to mv_port_intr(),
so that we now read/clear SError again in all cases.
Arrange the top of the function to be as close as possible
to what we need for a later update (in this series) for ERR_DEV handling.
Fix things so that libata-eh can attempt a READ_LOG_EXT_10H
in response to a failed NCQ command, by just doing a local
mv_eh_freeze() rather than ata_port_freeze().
This will now fully handle NCQ errors much of the time,
but more fixes are needed for FBS/PMP, and for certain chip errata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).
Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.
Bit22 of the GPIO port has to be set "on" when in NCQ mode.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all. So we need to prevent libata
from trying to feed us such mixtures.
Introduce mv_qc_defer() for this purpose, and use it for all chip versions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.
Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA. For non-EH operation, this will normally exit
without delay, other than the register read.
A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.
Logic taken/simplified from that in the Marvell proprietary driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic changes; no code changes.
-- try and improve consistency of naming.
-- add missing _OFS to tails of register offset definitions.
-- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
-- remove/move some dead comments
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net_cls_act: act_simple dont ignore realloc code
iwlwifi: make IWLWIFI a tristate
Revert "atm: Do not free already unregistered net device."
dccp: return -EINVAL on invalid feature length
irda: fix !PNP support for drivers/net/irda/smsc-ircc2.c
irda: fix !PNP support in drivers/net/irda/nsc-ircc.c
net_cls_act: Make act_simple use of netlink policy.
ip: Use inline function dst_metric() instead of direct access to dst->metric[]
ip: Make use of the inline function dst_metric_locked()
atm: Bad locking on br2684_devs modifications.
atm: Do not free already unregistered net device.
mac80211: Do not free net device after it is unregistered.
bridge: Consolidate error paths in br_add_bridge().
bridge: Net device leak in br_add_bridge().
niu: Fix probing regression for maramba on-board chips.
lapbeth: Release ->ethdev when unregistering device.
xfrm: convert empty xfrm_audit_* macros to functions
net: Fix useless comment reference loop.
sch_htb: remove from event queue in htb_parent_to_leaf()
IWLWIFI should be a tristate so that if IWLCORE and/or IWL3945 are m
and none of them is y kbuild doesn't create an empty
drivers/net/wireless/built-in.o
This patch also removes the pointless "default n".
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Support creation of FMRs with pages smaller than 4K
IB/ehca: Fix function return types
RDMA/cxgb3: Bump up the MPA connection setup timeout.
RDMA/cxgb3: Silently ignore close reply after abort.
RDMA/cxgb3: QP flush fixes
IB/ipoib: Fix transmit queue stalling forever
IB/mlx4: Fix off-by-one errors in calls to mlx4_ib_free_cq_buf()
Don't hard code a test against a minimum page shift of 12, since the
device may support smaller pages. Test against the actual smallest
page size from the device capabilities.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Also remove duplicate assignment of local_ca_ack_delay and change
min_t check for local_ca_ack_delay to u8 instead of int.
Signed-off-by: Stefan Roscher <stefan.roscher at de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 06916639e2 ("driver-core: add
dev_name() to help transition away from using bus_id") added a static
inline dev_name() and used it in dev_printk.
Unfortunately, drivers/edac/edac_core.h defines a macro called
dev_name(). Rename the latter.
Diagnosis by Tony Breeds and Michael Ellerman.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86 PCI: call dmi_check_pciprobe()
x86/pci: add pci=skip_isa_align command lines.
x86/pci: remove flag in pci_cfg_space_size_ext
x86: fix section mismatch in pci_scan_bus
The new mac_esp scsi driver needs CONFIG_SCSI_SPI_ATTRS, just like all other
drivers using the new esp_scsi core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/input/serio/hp_sdc.c: In function 'hp_sdc_take':
drivers/input/serio/hp_sdc.c:198: error: implicit declaration of function 'up'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The single step test is not terribly costly and it should be able to
pass at 1000 loops successfully in under 1 second. A non-kgdb timing
regression was found using this test, but it did not occur frequently
because by default the test was only executed a single time.
This patch changes the default for the single step test to 1000
iterations and allows for individual configuration of the single step
test to further exercise the kgdb subsystem when needed.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Shadowed variable and integer as NULL pointer fixes:
drivers/misc/kgdbts.c:877:6: warning: symbol 'sys_open_test' shadows an earlier one
drivers/misc/kgdbts.c:537:27: originally declared here
drivers/misc/kgdbts.c:378:22: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:386:22: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:468:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:472:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:502:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:506:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:509:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:523:20: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:527:20: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:530:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:541:21: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:545:21: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:548:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:559:30: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:563:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:573:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:574:19: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:578:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:588:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:589:19: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:593:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:602:16: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:604:15: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:925:3: warning: Using plain integer as NULL pointer
drivers/misc/kgdbts.c:938:3: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
x86.git testing found this build bug on v2.6.26-rc1:
ERROR: "pnp_get_resource" [drivers/net/irda/smsc-ircc2.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
the driver did not anticipate the case of !CONFIG_PNP which is rare but
still possible. Instead of restricting the driver to PNP-only in the
Kconfig space, add the (trivial) dummy struct pnp_driver - this is that
other drivers use in the !PNP case too.
The driver itself can in theory be initialized on !PNP too in certain
cases, via smsc_ircc_legacy_probe().
Patch only minimally build tested, i dont have this hardware.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
