musb_probe() only regards 0 as a wrong IRQ number, despite platform_get_irq()
that it calls returns -ENXIO in that case. It leads to musb_init_controller()
calling request_irq() with a negative IRQ number, and when it naturally
fails, the following is printed to the console:
request_irq -6 failed!
musb_init_controller failed with status -19
Fix musb_probe() to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes kernel panic during s2ram, which is caused
by the below:
- musb is not put into drv data of musb platform device if
CONFIG_USB_MUSB_HDRC_HCD is defined
- glue layer driver always get musb instance via platform_get_drvdata.
The patch fixes the issue by always puting musb into drv data
of musb platform device, which is doable even the platform device
is a host controller device.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
This reverts commit 32d5dc9520.
Needed to properly merge the musb changes that are in the
usb-next branch into Linus's tree.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_core.c #include's a bunch of ARM and DaVinci specific headers, goodness
knows why -- it happily compiles without them...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initial support for u8500 and u5500 platform.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
all glue layers are now fully moved to the
new setup. We are now using dev_pm_ops to
implement suspend/resume functionality and
thus, musb_platform_suspend/resume has become
deprecated and useless.
This patch drops those function pointers and
its uses.
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb core doesn't need to know about platform
specific details. So start moving clock
handling to platform glue layer and make
musb core agnostic about that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will make things simpler when choosing which
glue layer to compile. It avoids a lot of magic
around the "default" Kconfig option and lets the
user choose what exactly s/he wants to compile.
Signed-off-by: Felipe Balbi <balbi@ti.com>
preparing to a big refactor on musb code. We need
to be able to compile in all glue layers (or at
least all ARM-based ones) together and have a
working binary.
While preparing for that, we move every glue
layer to export only one symbol, which is
a struct musb_platform_ops, and make all
other functions static.
Later patches will come to allow for compiling
all glue layers together and have a working
binary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Soon resource data will get automatically
populated from a set of autogenerated data
from TI's hardware database for the OMAP
platform.
Such database, might not have resources at
the expected order by the current drivers.
While we could hack in some exceptions to
that tool to generate resources in a specific
order, it seems less fragile to use the
resource name instead. That way, no matter
what order the resources are generated, the
driver still work.
Modified the OMAP, Blackfin and Davinci
architecture files to add the name of the IRQs
in the resource structures and musb driver to
use the platform_get_irq_byname() api to get
the device and dma irq numbers instead of using
the index.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed the board_data parameter being
passed to musb_platform_init function
as board_data can be extracted from
device structure which is already member
of musb structure.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Inventra DMA engine used with the MUSB controller in many
SoCs cannot use DMA for control transfers on EP0, but can use
DMA for all other transfers.
The USB core maps urbs for DMA if hcd->self.uses_dma is true.
(hcd->self.uses_dma is true for MUSB as well).
Split the uses_dma flag into two - one that says if the
controller needs to use PIO for control transfers, and
another which says if the controller uses DMA (for all
other transfers).
Also, populate this flag for all MUSB by default.
(Tested on OMAP3 and OMAP4 boards, with EHCI and MUSB HCDs
simultaneously in use).
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since clock support is optional across processors, don't make the whole
musb pm paths depend upon it. Just conditionalize the clock accesses.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some actions like musb_platform_exit are only performed on module
removal and not on shutdown, which results in PHY being left enabled
on reboot at least. This is sometimes causing strange failures after
reboot (observed on OMAP3 pandora board), when DEVCTL does not report
VBUS state correctly due to unknown reasons (possibly because of
communication issues between musb IP and PHY). Running
musb_platform_exit before reset seems to resolve that issue.
Move some exit code from musb_remove() to musb_shutdown() so that it
is performed on both module removal and shutdown/reset. Also convert
the host check so that it doesn't need #ifdef.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM35x supports only 32bit read operations so we need to have
workaround for 8bit and 16bit read operations.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 461972d8a4 (musb_core: don't call
musb_platform_exit() twice), unloading the driver module results in a WARNING
"kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being
called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode.
There exists dubious and unbalanced put_device() call in musb_free() which
takes place only in the OTG mode. As this commit caused musb_platform_exit()
to be called (and so unregister the NOP transceiver) before this put_device()
call, this function references already freed memory.
On the other hand, all the glue layers miss the otg_put_transceiver() call,
complementary to the otg_get_transceiver() call that they do. So, I think
the solution is to get rid of the strange put_device() call, and instead
call otg_put_transceiver() in the glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will ignore any SESSREQ interrupt if musb is B state.
Charger detection may cause spurious SESSREQ interrupts.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since not all platforms are using the same offset 0x10 in
musb_save/restore_context() eg Blackfin the offset is 0x40,
Change the indexed address to direct.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)
Tweak the fallback stubs so that they do work as intended.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 1c25fda4a0 (usb: musb: handle irqs in the
order dictated by programming guide) forgot to get rid of the old 'STAGE0_MASK'
filter for calling musb_stage0_irq(), so now disconnect and suspend interrupts
are effectively ignored...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a part of aligning the ISR code for MUSB with the specs, the
ISR code was re-written.
See Commit 1c25fda4a0 (usb: musb: handle
irqs in the order dictated by programming guide)
With this the suspend interrupt came accidently under CONFIG_USB_MUSB_HDRC_HCD.
The fix brings suspend interrupt handling outside
CONFIG_USB_MUSB_HDRC_HCD.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds helper functions for ULPI access, and implements
otg_io_access_ops for musb.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when we fail to probe(), we can call musb_exit_debugfs().
Allow that by removing section annotations.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
for now only a simple register dump entry (which can
be rather useful on debugging) and a way to start
test modes.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Program the OTG_INTERFSEL register based on
transcevier type passed from board file.
Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses. In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.
There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function forgets to call usb_remove_hcd() or musb_gadget_cleanup() iff
sysfs_create_group() fails.
[ felipe.balbi@nokia.com : review the entire error path
not only when we fail hcd or gadget ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_platform_exit() is called twice from musb_init_controller() iff controller
initialization fails. Move the call (and the DevCtl register writes surrounding
it) from musb_free() to musb_remove().
Fix mispalced and now incorrect 'goto's in musb_init_controller().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resetting 'musb->clock' to NULL in musb_shutdown() prevents musb_platform_exit()
from properly disabling the clock when unloading the driver -- don't do it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate/unbalanced calls to clk_disable()/clk_put() in musb_free():
- clk_disable() is called by musb_platform_exit() just prior to this call;
- clk_put() is called by the callers of musb_free() prior to calling it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and avoid a compilation if we disable host side
of musb.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.
This fixes building for Blackfin parts again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
USB: backlight, appledisplay: fix incomplete registration failure handling
USB: pl2303: remove unnecessary reset of usb_device in urbs
USB: ftdi_sio: remove obsolete check in unthrottle
USB: ftdi_sio: remove unused tx_bytes counter
USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
USB: pl2303: initial TIOCGSERIAL support
USB: option: add Longcheer/Longsung vendor ID
USB: fix I2C API usage in ohci-pnx4008.
USB: usbmon: mask seconds properly in text API
USB: sisusbvga: no unnecessary GFP_ATOMIC
USB: storage: onetouch: unnecessary GFP_ATOMIC
USB: serial: ftdi: add CONTEC vendor and product id
USB: remove references to port->port.count from the serial drivers
USB: tty: Prune uses of tty_request_room in the USB layer
USB: tty: Add a function to insert a string of characters with the same flag
USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
USB: tty: kill request_room for USB ACM class
USB: tty: sort out the request_room handling for whiteheat
USB: storage: fix misplaced parenthesis
USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
...
we were printing the info about musb probe too early where
it was still possible for things to go wrong. Move the
down right before the return 0 statement. While at that
also convert pr_info to dev_info.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when probe() fails, we should iounmap() the mapped address.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
