This patch adds the LINK_SPEED mode to the list of CPMU modes that can
cause the loopback tests to fail. These bugs are planned to be fixed in
future revisions of the chip, so the patch qualifies the fixes as such.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer devices contain bootcode in the chip's private ROM area. This
bootcode is called selfboot. Selfboot can be patched in the device's
NVRAM and the patches can have several formats. In one particular
format, the checksum calculation needs to be slightly modified. This
patch adjusts the NVRAM test code for that case, and add support for the
missing formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU
link speed mode is enabled, and the MAC clock is running at 1.5Mhz. The
fix is to run the MAC clock at faster speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle. This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available. When the PHY is powered down, the clock the MAC depends on
is disabled. The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates. The tg3 driver has code to detect this
condition and resets the device during initialization. On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761. However, during this initialization stage, communications
to the APE registers have not yet been set up. The driver then
dereferences a NULL pointer and crashes the machine. The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify some code by eliminating duplicate if-else clauses in
packet_do_bind().
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I removed net-modules.txt because it only contained ancient
information I missed that many Kconfig entries pointed to this ancient
information.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.
Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348e (the NAPI changes) made sungem unconditionally enable
NAPI when resuming and unconditionally disable when suspending, this,
however, makes napi_disable() hang when suspending when the interface
was taken down before suspend because taking the interface down also
disables NAPI. This patch makes touching the napi struct in
suspend/resume code paths depend on having the interface up, thereby
fixing the hang on suspend.
The patch also moves the napi_disable() in gem_close() under the lock so
that the NAPI state is always modified atomically together with the
"opened" variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix sparse warnings "Using plain integer as NULL pointer"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userland neighbor discovery options are typically heavily involved with
the interface on which thay are received: add a missing ifindex field to
the original struct. Thanks to Rmi Denis-Courmont.
Signed-off-by: Pierre Ynard <linkfanel@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
While a signal is blocked, it must be posted even if its action is
SIG_IGN or is SIG_DFL with the default action to ignore. This works
right most of the time, but is broken when a sigwait (rt_sigtimedwait)
is in progress. This changes the early-discard check to respect
real_blocked. ~blocked is the set to check for "should wake up now",
but ~(blocked|real_blocked) is the set for "blocked" semantics as
defined by POSIX.
This fixes bugzilla entry 9347, see
http://bugzilla.kernel.org/show_bug.cgi?id=9347
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As with commit 7fc90ec93a ("knfsd: nfsd:
call nfsd_setuser() on fh_compose(), fix nfsd4 permissions problem")
this is a case where we need to redo a security check in fh_verify()
even though the filehandle already has an associated dentry--if the
filehandle was created by fh_compose() in an earlier operation of the
nfsv4 compound, then we may not have done these checks yet.
Without this fix it is possible, for example, to traverse from an export
without the secure ports requirement to one with it in a single
compound, and bypass the secure port check on the new export.
While we're here, fix up some minor style problems and change a printk()
to a dprintk(), to make it harder for random unprivileged users to spam
the logs.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Reviewed-By: NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The v2/v3 acl code in nfsd is translating any return from fh_verify() to
nfserr_inval. This is particularly unfortunate in the case of an
nfserr_dropit return, which is an internal error meant to indicate to
callers that this request has been deferred and should just be dropped
pending the results of an upcall to mountd.
Thanks to Roland <devzero@web.de> for bug report and data collection.
Cc: Roland <devzero@web.de>
Acked-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Reviewed-By: NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 5adc5be7cd.
Alexey Dobriyan reports that it causes huge slowdowns under some loads,
in his case a "mkfs.ext2" on a 30G partition. With the placement bias,
the mkfs took over four minutes, with it reverted it's back to about ten
seconds for Alexey.
Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After unification of the Kconfig files and
introducing K64BIT support in kconfig
it required only trivial changes to enable
"make ARCH=x86".
With this patch you can build for x86_64 in several ways:
1) make ARCH=x86_64
2) make ARCH=x86 K64BIT=y
3) make ARCH=x86 menuconfig
=> select 64-bit
Likewise for i386 with the addition that
i386 is default is you say ARCH=x86.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
For x86 ARCH may say i386 or x86_64 and soon x86.
Rely on CONFIG_X64_32 to select between 32/64 or just
hardcode the value as appropriate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
The variable K64BIT can now be used to select the
value of CONFIG_64BIT.
This is for example useful for powerpc to generate
allmodconfig for both bit sizes - like this:
make ARCH=powerpc K64BIT=y
make ARCH=powerpc K64BIT=n
To use this the Kconfig file must use "64BIT" as the
config value to select between 32 and 64 bit.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Add conf_set_env_sym() that can set an already defined symbol
based on the value of an environment variable.
Unknown symbols are silently ignored.
A warning is printed if the value of the environment variable
is unexpected.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
With this patch we have all the Kconfig file shared
between i386 and x86_64.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Most of the arch settings were equal so combine them
in the first part of Kconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
No functional changes.
A prepatory step towards full unification.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
To ease unification of Kconfig.i386 and Kconfig.x86_64
add X86_64 dependencies to all x86_64 specific symbols.
This patch introduce no functional changes but is one step
towards unification. This smaller step is used to ease
review of the patch set.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
To ease unification of Kconfig.i386 and Kconfig.x86_64
add X86_32 dependencies to all i386 specific symbols.
This patch introduce no functional changes but is one step
towards unification. This smaller step is used to ease
review of the patch set.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Move all CPU definitions to Kconfig.cpu
Always define X86_MINIMUM_CPU_FAMILY and do the
obvious code cleanup in boot/cpucheck.c
Comments from: Adrian Bunk <bunk@kernel.org> incorporated.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Brian Gerst <bgerst@didntduck.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
This step introduces the file arch/x86/Kconfig
which contains all the menu's from "Power Management"
and below.
The main part of the new Kconfig file is shared
and the remaining i386/x86_64 specific symbols
are covered by dependencies.
A x86_64 allmodconfig build did not show any differences.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Merge the two Kconfig files to a single file.
Checked using make allmodconfig for x86_64.
No changes in build.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: SVM: Intercept the 'invd' and 'wbinvd' instructions
KVM: x86 emulator: invd instruction
KVM: SVM: Defer nmi processing until switch to host state is complete
KVM: SVM: Fix SMP with kernel apic
KVM: x86 emulator: fix 'push imm8' emulation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio:
virtio: Force use of power-of-two for descriptor ring sizes
lguest: Fix lguest virtio-blk backend size computation
virtio: Fix used_idx wrap-around
virtio: more fallout from scatterlist changes.
virtio: fix vring_init for 64 bits
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (39 commits)
[INET]: Small possible memory leak in FIB rules
[NETNS]: init dev_base_lock only once
[UNIX]: The unix_nr_socks limit can be exceeded
[AF_UNIX]: Convert socks to unix_socks in scan_inflight, not in callbacks
[AF_UNIX]: Make unix_tot_inflight counter non-atomic
[AF_PACKET]: Allow multicast traffic to be caught by ORIGDEV when bonded
ssb: Fix PCMCIA-host lowlevel bus access
mac80211: fix MAC80211_RCSIMPLE Kconfig
mac80211: make "decrypt failed" messages conditional upon MAC80211_DEBUG
mac80211: use IW_AUTH_PRIVACY_INVOKED rather than IW_AUTH_KEY_MGMT
mac80211: remove unused driver ops
mac80211: remove ieee80211_common.h
softmac: MAINTAINERS update
rfkill: Fix sparse warning
rfkill: Use mutex_lock() at register and add sanity check
iwlwifi: select proper rate control algorithm
mac80211: allow driver to ask for a rate control algorithm
mac80211: don't allow registering the same rate control twice
rfkill: Use subsys_initcall
mac80211: make simple rate control algorithm built-in
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (21 commits)
[CIFS] fix oops on second mount to same server when null auth is used
[CIFS] Fix stale mode after readdir when cifsacl specified
[CIFS] add mode to acl conversion helper function
[CIFS] Fix incorrect mode when ACL had deny access control entries
[CIFS] Add uid to key description so krb can handle user mounts
[CIFS] Fix walking out end of cifs dacl
[CIFS] Add upcall files for cifs to use spnego/kerberos
[CIFS] add OIDs for KRB5 and MSKRB5 to ASN1 parsing routines
[CIFS] Register and unregister cifs_spnego_key_type on module init/exit
[CIFS] implement upcalls for SPNEGO blob via keyctl API
[CIFS] allow cifs_calc_signature2 to deal with a zero length iovec
[CIFS] If no Access Control Entries, set mode perm bits to zero
[CIFS] when mount helper missing fix slash wrong direction in share
[CIFS] Don't request too much permission when reading an ACL
[CIFS] enable get mode from ACL when cifsacl mount option specified
[CIFS] ACL support part 8
[CIFS] acl support part 7
[CIFS] acl support part 6
[CIFS] acl support part 6
[CIFS] remove unused funtion compile warning when experimental off
...
restore sigcontext is taking a DNA exception while restoring FP context
from the user stack, during the sigreturn. Appended patch fixes it by
doing clts() if the app doesn't touch FP during the signal handler
execution. This will stop generating a DNA, during the fxrstor in the
sigreturn.
This improves 64-bit lat_sig numbers by ~30% on my core2 platform.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The coredump code always calls set_dumpable(0) when it starts (even
if RLIMIT_CORE prevents any core from being dumped). The effect of
this (via task_dumpable) is to make /proc/pid/* files owned by root
instead of the user, so the user can no longer examine his own
process--in a case where there was never any privileged data to
protect. This affects e.g. auxv, environ, fd; in Fedora (execshield)
kernels, also maps. In practice, you can only notice this when a
debugger has requested PTRACE_EVENT_EXIT tracing.
set_dumpable was only used in do_coredump for synchronization and not
intended for any security purpose. (It doesn't secure anything that wasn't
already unsecured when a process dies by SIGTERM instead of SIGQUIT.)
This changes do_coredump to check the core_waiters count as the means of
synchronization, which is sufficient. Now we leave the "dumpable" bits alone.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In net/sctp/sm_statefuns.c::sctp_sf_abort_violation() we may leak
the storage allocated for 'abort' by returning from the function
without using or freeing it. This happens in case
"sctp_auth_recv_cid(SCTP_CID_ABORT, asoc)" is true and we jump to
the 'discard' label.
Spotted by the Coverity checker.
The simple fix is to simply move the creation of the "abort chunk"
to after the possible jump to the 'discard' label. This way we don't
even have to allocate the memory at all in the problem case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
The virtio descriptor rings of size N-1 were nicely set up to be
aligned to an N-byte boundary. But as Anthony Liguori points out, the
free-running indices used by virtio require that the sizes be a power
of 2, otherwise we get problems on wrap (demonstrated with lguest).
So we replace the clever "2^n-1" scheme with a simple "align to page
boundary" scheme: this means that all virtio rings take at least two
pages, but it's safer than guessing cache alignment.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This seems like an obvious typo but it's worked in the past because the virtio
blk frontend just ignores the length field on completion.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The more_used() function compares the vq->vring.used->idx with last_used_idx.
Since vq->vring.used->idx is a 16-bit integer, and last_used_idx is an
unsigned int, this results in unpredictable behavior when vq->vring.used->idx
wraps around.
This patch corrects this by changing last_used_idx to the correct type.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch fixes a typo in vring_init(). This happens to work today in lguest
because the sizeof(struct vring_desc) is 16 and struct vring contains 3
pointers and an unsigned int so on 32-bit
sizeof(struct vring_desc) == sizeof(struct vring). However, this is no longer
true on 64-bit where the bug is exposed.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently the Geode AES module fails to encrypt or decrypt if
the coherent bits are not set what is currently the case if the
encryption does not occur inplace. However, the encryption works
on my Geode machine _only_ if the coherent bits are always set.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
remap_pfn_range() takes care of setting the appropriate VM_*
flags itself; there's no need for callers of remap_pfn_range()
to set VM_RESERVED before it is called.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a small memory leak. Default fib rules can be deleted by
the user if the rule does not carry FIB_RULE_PERMANENT flag, f.e. by
ip rule flush
Such a rule will not be freed as the ref-counter has 2 on start and becomes
clearly unreachable after removal.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
* it already statically initialized
* reinitializing live global spinlock every time netns is
setup is also wrong
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unix_nr_socks value is limited with the 2 * get_max_files() value,
as seen from the unix_create1(). However, the check and the actual
increment are separated with the GFP_KERNEL allocation, so this limit
can be exceeded under a memory pressure - task may go to sleep freeing
the pages and some other task will be allowed to allocate a new sock
and so on and so forth.
So make the increment before the check (similar thing is done in the
sock_kmalloc) and go to kmalloc after this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
