Check that b2b_mw_idx is in range of the number of memory windows when
initializing the device. The workaround is considered to be in effect
only if the device b2b_idx is exactly UINT_MAX, instead of any index
past the last memory window.
Only print B2B MW workaround information in debugfs if the workaround is
in effect.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Allocate two DMA channels, one for TX operation and one for RX
operation, instead of having one DMA channel for everything. This
provides slightly better performance, and also will make error handling
cleaner later on.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The dma_sync_wait can hurt the performance of workloads mixed with both
large and small frames. Large frames will be copied using the dma
engine. Small frames will be copied by the cpu. The dma_sync_wait
prevents the cpu and dma engine copying in parallel.
In the period where the cpu is copying, the dma engine is stopped. The
dma engine is not doing any useful work to copy large frames during that
time, and the additional time to restart the dma engine for the next
large frame. This will decrease the throughput for the portion of a
workload with large frames.
In the period where the dma engine is copying, the cpu is held up
waiting for dma to complete. The small frames processing will be
delayed until the dma is complete. The RX frames are completed
in-order, and the processing of small frames takes very little time, so
dma_sync_wait may have an insignificant impact on the respose time of
frames. The more significant impact is to the system, because the delay
in dma_sync_wait is implemented as busy non-blocking wait. This can
prevent the delayed core from doing any useful work, even if it could be
processing work for other drivers, unrelated to transport RX processing.
After applying the earlier patch to fix out-of-order RX acknoledgement,
the dma_sync_wait is no longer necessary. Remove it, so that cpu memcpy
will proceed immediately for small frames, in parallel with ongoing dma
for large frames. Do not hold up the cpu from doing work while dma is
in progress. The prior fix will continue to ensure in-order completion
of the RX frames to the upper layer, and in-order delivery of the RX
acknoledgement.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Make QP stats info more readable for debugging purposes. Also add an
entry to indicate whether DMA is being used.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The list should be added from the bottom and not the top in order to
ensure the transport is provided in the same order to clients as ntb
devices are discovered.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Adding PCI Device IDs for B2B (back to back), RP (root port, primary),
and TB (transparent bridge, secondary) devices.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Right now if we push the NTB really hard, we start dropping packets due
to not able to process the packets fast enough. We need to st:qop the
upper layer from flooding us when that happens.
A timer is necessary in order to restart the queue once the resource has
been processed on the receive side. Due to the way NTB is setup, the
resources on the tx side are tied to the processing of the rx side and
there's no async way to know when the rx side has released those
resources.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Avoid any chance of format string expansion when calling dev_set_name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Remove early dereference of a pointer that is checked later in the code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
A plain 32 bit integer will overflow for values over 4GiB.
Change the plain integer size to the appropriate size type in
ntb_set_mw. Change the type of the size parameter and two local
variables used for size.
Even if there is no overflow, a size of zero is invalid here.
Reported-by: Juyoung Jung <jjung@micron.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Schedule to receive on QP link up, to make sure that the doorbell is
properly cleared for interrupts.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the remote side is not up, we do not have all the context for the
transport, and that causes NULL ptr access. Have the debugfs reads check
to see if transport is up before we make access.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Currently the debugfs does not have files for all NTB transport queue
pairs. When there are multiple NTBs present in a system, the QP names
of the last transport clobber the names of previously added transport
QPs. Only the last added QPs can be observed via debugfs.
Create a directory per NTB transport to associate the QPs with that
transport. Name the directory the same as the PCI device.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
It was possible for a synchronous update of the RX index in the error
case to get ahead of the asynchronous RX index update in the normal
case. Change the RX processing to preserve an RX completion order.
There were two error cases. First, if a buffer is not present to
receive data, there would be no queue entry to preserve the RX
completion order. Instead of dropping the RX frame, leave the RX frame
in the ring. Schedule RX processing when RX entries are enqueued, in
case there are RX frames waiting in the ring to be received.
Second, if a buffer is too small to receive data, drop the frame in the
ring, mark the RX entry as done, and indicate the error in the RX entry
length. Check for a negative length in the receive callback in
ntb_netdev, and count occurrences as rx_length_errors.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When split BAR is enabled, the driver needs to dump out the split BAR
registers rather than the original 64bit BAR registers.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The unsafe doorbell and scratchpad access should display reason when
WARN is called. Otherwise we get a stack dump without any explanation.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Printouts driver name and version to indicate what is being loaded.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k. Change the driver default to 64k.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Disable DMA usage by default, since the CPU provides much better
performance with write combining. Provide a module parameter to enable
DMA usage when offloading the memcpy is preferred.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Changing the memory window BAR mappings to write combining significantly
boosts the performance. We will also use memcpy that uses non-temporal
store, which showed performance improvement when doing non-cached
memcpys.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Allocate memory and request the DMA channel for the same NUMA node as
the NTB device.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the ntb transport is connecting and waiting for the peer, the debug
console receives lots of debug level messages about the remote qp link
status being down. Rate limit those messages.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a simple debugging driver that enables the doorbell and
scratch pad registers to be read and written from the debugfs. This
tool enables more complicated debugging to be scripted from user space.
This driver may be used to test that your ntb hardware and drivers are
functioning at a basic level.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a simple ping pong driver that exercises the scratch pads and
doorbells of the ntb hardware. This driver may be used to test that
your ntb hardware and drivers are functioning at a basic level.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Reset the link stats when the link goes down. In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them. Reset
all the stats, to be consistent.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On link down, don't advance RX index to the next entry. The next entry
should never be valid after receiving the link down flag.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport. Change the messages so they are distinct.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer. The transport expects the peer values to be
the same as the local values, so this issue was not obvious.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer. Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Commit ab760a0 (ntb: Adding split BAR support for Haswell platforms)
changed ntb_device's mw from a fixed-size array into a pointer that is
allocated based on limits.max_mw; however, on Atom platforms, max_mw
is not initialized until ntb_device_setup(), which happens after the
allocation.
Fill out max_mw in ntb_atom_detect() to match ntb_xeon_detect(); this
happens before the use of max_mw in the ndev->mw allocation.
Fixes a null pointer dereference on Atom platforms with ntb hardware.
v2: fix typo (mw_max should be max_mw)
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The MW regbase and vbase(s) were not being freed if an error occurred
in the vbase allocation loop. This is corrected by updating the error
path for the allocation loop to err4.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The PCI core now disables MSI and MSI-X for all devices during enumeration
regardless of CONFIG_PCI_MSI. Remove device-specific code to disable
MSI/MSI-X.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On the Haswell platform, a split BAR option to allow creation of 2
32bit BARs (4 and 5) from the 64bit BAR 4. Adding support for this
new option.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of using a module parameter, we should detect the errata via
PCI DID and then set an appropriate flag. This will be used for additional
errata later on.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
To simplify some of the platform detection code. Move the platform detection
to a function to be called earlier.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Move the platform detection function to separate functions to allow
easier maintenence.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Create a debugfs entry for the NTB device to log the basic device info,
as well as display the error count on a number of registers.
Signed-off-by: Jon Mason <jon.mason@intel.com>
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The detection of an uneven number of queues on the given memory windows
was not correct. The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.
Signed-off-by: Jon Mason <jon.mason@intel.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
This is an cleanup effort to make ntb_setup_msix() more
readable - use ntb_setup_bwd_msix() to init MSI-Xs on
BWD hardware and ntb_setup_snb_msix() - on SNB hardware.
Function ntb_setup_snb_msix() also initializes MSI-Xs the
way it should has been done - looping pci_enable_msix()
until success or failure.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
