Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change order data of buffer in FM simple_tune function. It is usefull for:
1. Set data of tuner with CP bit UP. 0xCE for MK5 or 0xC6 for MK3
2. When call simple_fm_tune, read this byte from config and overwrite
this byte in function simple_radio_bandswitch for set CP bit to OFF.
Of course it can be usefull for other tuner for overwrite default
settings of FM.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ATSC and DVB @ 6MHz bandwidth require the same offset.
While we're fixing it, let's cleanup the bandwidth setup to better
reflect the fact that it is a function of the bandwidth.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only two countries that are known to use 6MHz bandwidth are Taiwan
and Uruguay. Both use QAM subcarriers at OFTM.
This patch fixes the firmware load for such countries, where the
required firmware is the QAM one.
This also confirms the previous tests where it was noticed that the 6MHz
QAM firmware doesn't work for cable. So, this patch also removes support
for DVB-C, instead of just printing a warning.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of polling at 100ms intervals for register writes, poll at 5ms
intervals. This is consistent with the xc5000 specification, and improves
tuning time by up to 500 ms on devices that such as the au0828 which do not
properly implement i2c clock stretching (since the five register writes that
occur for a tuning request often do not complete immediately but do complete
far before 100ms has gone by).
The net amount of time we wait before timing out is unchanged (500ms).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds XC5000 supports for DVB-T 6MHz and 8MHz bandwidth.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xceive has graciously allowed us to now freely redistribute the xc5000
firmware, which eliminates the need for users to manually extract the blob
from the Hauppauge driver.
Thanks to Brian Mathews <bmathews@xceive.com> for providing this code
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a typo in the module description for the "no_poweroff" option, where the
help was being associated with the "debug" option instead.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide for the ability for a user to disable putting the tuner to sleep, in
case he doesn't want to incur the cost of reloading the firmware when starting
up his/her application. The module options are intentionally identical to
xc3028.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it a little more obvious in the dmesg output what is going on during
firmware upload. This is more important for boards like the HVR-950q that
take nearly seven seconds to do the upload.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Starting in firmware version 1.1.44, Xceive recommends using the FINERFREQ for
all normal tuning (the doc indicates reg 0x03 should only be used for fast
scanning for channel lock)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Expose the firmware build number along with the other version info
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions.
Their technical support informed me that the correct way to put the tuner
to sleep is to pull the reset pin (but don't reload the firmware).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This switches to a new version of the xc5000 firmware, extracted from the
latest Hauppauge driver. It includes the support for the XREG_BUSY register
(a lack of which was causing tuning to take 3200ms instead of around 300ms).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't sleep for 400ms polling the tuner's lock if in digital mode (since the
xc5000 lock status registers appear to only be reliable in analog mode)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bring back the code that puts the xc5000 to sleep. For the Pinnacle 801e
this results in power consumption at idle dropping from 325ma to 124ma.
If there are *actually* any devices that don't work in this configuration,
they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's
suggestion)
Also, had to make sure we were making sure the firmware was loaded in the
digital version of set_params, or else we end up get i2c errors if the
device is asleep
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make return value checking for calls to i2c routines explicit.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup the i2c write routine, getting rid of a passthrough function with only
one caller
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch centralizes the i2c read functions, and eliminates pass-through
function only called by one caller.
Make reading of xc5000 registers an atomic i2c transaction in case we're on a
multi-master bus.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch gets rid of the xc2028 FIRMWARE_NAME_MAX reference.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Michel Ludwig <michel.ludwig@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
The v4l2-ioctl core now only allows buffer types for which the
corresponding ->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(g|s)_parm.
The driver was only allowing VIDEO_CAPTURE buffers for g_parm, but since
the driver defines ->vidioc_try_fmt_vid_overlay() it will now allow
VIDEO_OVERLAY buffers as well. This should be fine as the fields the
driver fills in, readbuffers and frame rate, aren't wrong for VIDEO_OVERLAY
buffers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Separate tuning table for DVB-C solves tuning problem at 388MHz
TechnoTrend C-1501 DVB-C card does not lock on 388MHz. I assume that
existing frequency table is valid for DVB-T.
This is suggested by the name of the table: tda827xa_dvbt.
Added a table for DVB-C with the name tda827xa_dvbc.
Added runtime selection of the DVB-C table when the tuner is type
FE_QAM.
This should leave the behaviour of this driver with with DVB_T tuners
unchanged. This modification is in file tda827x.c
The tda827x.c gives the following warning message when debug=1:
tda827x: tda827x_config not defined, cannot set LNA gain!
Solved this by adding a tda827x_config struct in budget-ci.c.
Signed-off-by: Klaas de Waal <klaas.de.waal@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several Kconfig items using CUSTOMIZE. Yet, most use the English
writing CUSTOMISE. This generates lots of trouble, because people sometimes type
the Kbuild item different.
Let's standardise every occurrence using the same syntax.
The changes were generated by this small shell script:
for i in `find linux -type f`; do sed s,CUSTOMIZE,CUSTOMISE,g $i >/tmp/a && mv /tmp/a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc5000 driver has a bug where the IF is always set to whatever the first
caller to dvb_attach() provides. This fails when the device requires an IF
other than 5380 and the analog driver is loaded first through tuner-core
(which always supplies the hard-coded value of 5380).
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tda827x driver supports a feature that the tda18271 driver was lacking
until now. This patch adds support for device-level configuration via the
tuner callback configuration interface.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_enum_fmt_vid_overlay() did nothing but call
vidioc_enum_fmt_vid_cap(), so just make
saa7146_video_ioctl_ops.vidioc_enum_fmt_vid_overlay point to
vidioc_enum_fmt_vid_cap() and get ride of vidioc_enum_fmt_vid_overlay().
Have gparm use v4l2_video_std_frame_period to fill in the frame period
instead of just assuming PAL.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
report TUNER_STATUS_LOCKED if rf_locked or ref_locked
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function does not work properly and is not necessary - remove it for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Analog doesn't work in this driver yet. This code just adds extra bloat,
so remove it for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver infrared remote code part is altered to switch to a work queue.
Also ir_codes table moved to ir-common module for shared access.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added support for I2C device at address 0x40 and subaddress 0x0d/0x0b
that provides remote control key reading support for AVerMedia Cardbus
Hybrid card, possibly for other AVerMedia Cardbus cards.
The I2C address 0x40 doesn't like the SAA7134's 0xfd quirk, so it was
disabled.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With while (i++ < 10) { ... } i can reach 11, so callibration still
succeeds at i == 10.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
