While at it remove some superfluous parenthesis.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
These files are only used on imx31. This makes the name consistent with
the imx35 files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
The macro mx31_revision() used to take the global variable system_rev to
determine the CPU revision number. However, this number is expected to
be set by the bootloader and is usually zero (at least on my MX31 based
boards here). More than that, it is usually taken to identify the
board's revision, not the CPU's.
Fix that by reading the the CPU's SREV register instead.
Right now, mx31_read_cpu_rev() is called from mx31_clocks_init() which
is admittedly not a good place for it. However, we need to enable the
IIM clock first, and the clock code also has conditional code that
depends on mx31_revision() returning the right thing.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit splits the support code for LogicPD's mx31lite hardware
into module and board specific parts.
This introduces a new mandatory coreparam called 'mx31lite_baseboard'
which specifies the base board support to use. For now, only the LiteKit
development board is supported, and developers of own boards are
encouraged to use that as reference.
The UART support moved to the board code.
Some comments were amended along the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support code for lilly-1131 is implemented in a module/baseboard
fashion. All code specific to peripherals found on the development board
will go to this file.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based
modules. The module needs a baseboard support to work which will be
added in the next patch.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for Dave/DENX QongEVB-LITE i.MX31-based
board. It includes support for clocks initialization, UART1, NOR-flash,
FPGA-attached NAND flash and DNET ethernet controller (inside FPGA).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds clock support for i.MX35 SoCs. We do not support setting
of clock rates yet, but most interesting clock rates should be reported.
I couldn't test all clock rates and the datasheet contains some obvious
bugs, so expect some bugs in this code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This enables our mx31moboard to be used on the different baseboards that
we are developping according to the application needs. There are not
many differences between the boards for now, but when other peripherals
are available for mx31 the differences are going to grow.
v2: takes Sascha's comments into account
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Initial support for mx31moboard platfor with 3 serial ports
and NOR Flash
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add basic support to the MX31PDK development board, also known
as MX31 3DS or MX31 3-stack board (http://www.freescale.com/imx31pdk).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for i.MX31 LiteKit by LogicPD.
With printascii() in kernel/printk.c, it boots right into the
rootfs-panic.
Note: This is a modified version of Daniel's patch to fit into this patch
stack.
> On 09.06.2008, at 17:26, Russell King - ARM Linux wrote:
>
> > I would much prefer it if board specific includes were included by the
> > code which needs them rather than in asm/arch/hardware.h. With the
> > device model, drivers shouldn't need to include any board specific
> > includes - only the board specific C file should need it.
>
> The new version of this patch (#5102) has been uploaded to the patch
> tracker this morning.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
--
arch/arm/configs/mx31litekit_defconfig | 1100 ++++++++++++++++++++++++++++++
arch/arm/mach-mx3/Kconfig | 7
arch/arm/mach-mx3/Makefile | 1
arch/arm/mach-mx3/mx31lite.c | 96 ++
include/asm-arm/arch-mxc/board-mx31lite.h | 38 +
include/asm-arm/arch-mxc/debug-macro.S | 3
6 files changed, 1245 insertions(+)
This patch adds timer support for the i.MX machine family. This code can
be used on the following machs:
- i.MX1 (tested)
- i.MX2 (i.MX21 (to be tested), i.MX27 (tested))
- i.MX3 (i.MX31 (tested))
TODO: It seems impossible to build a kernel for more than one CPU because the
timer do not follow the platform device rules. So it does only work if
timer 1 can be accessed on all CPUs at the same address.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
