This patch implements locking using the semaphore in scratchpad
memory preventing any concurrent access to scratchpad from OMAP
and Baseband/Modem processor.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pass cpuidle parameters for RX-51. Numbers based on
measurements made in October 2009 for PM optimized
kernel with CPU freq enabled. Assumes OPP2 (main
idle OPP, and worst case latencies).
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The sleep indicator LEDs can be enabled/disabled by toggling GPIO162.
Use the LED GPIO class to export this LED functionality to userspace.
To enable:
# echo 1 > /sys/class/leds/sleep_ind/brightness
To disable:
# echo 0 > /sys/class/leds/sleep_ind/brightness
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Different boards benefit differently from the available
seven C-states for cpu idle. In most cases, only few,
properly spaced (in terms of consumption and latency)
C-states are required to make the power management
optimal. Hence we need a possibility to pass which
C-states are actually used for each board.
So added the valid field to cpuidle_params and added
support to 3430sdp, which uses the paramenter passing.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The CPUidle C state latencies and thresholds are dependent on various
board specific details. This patch makes it possible to configure
these values from the respective board files.
omap3_pm_init_cpuidle() can now be optionally called from board files
to pass board specific cpuidle parameters. If the board files do not
use this function to pass the params default values are used which
might cause higher consumption dur to wrong state selection by the
governor.
This patch only updates the 3430sdp board files to use
omap3_pm_init_cpuidle().
From Kalle, in addition to original patch from Rajendra:
Building without CONFIG_CPU_IDLE or CONFIG_PM causes build to fail if
cpu idle parameters are tried to pass using omap3_pm_init_cpuidle
function.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When 'enable_off_mode' is 0, the target power state for MPU
and CORE was locally changed to PWRDM_POWER_RET but, the
statistics are updated for idle state originally selected
by the governor.
This patch 'invalidates' the idle states that lead either of
MPU or Core to PWRDM_POWER_OFF state when 'enable_off_mode'
is '0'. The states are valid once 'enable_off_mode' is set
to '1'.
Added function next_valid_state() to check if current state
is valid; else get the next valid state. It is called from
omap3_enter_idle_bm().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The check for a valid mux name should be performed regardless of whether
DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.33-rc8 #10)
PC is at strcmp+0x18/0x40
LR is at omap_mux_init_signal+0x68/0x14c
...
This fixes the issue currently seen with boards not booting up
if DEBUG_FS is not enabled in defconfig.
Note that the earlier ifndef + ifdef now becomes simpler ifdef else:
If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected,
we only want the GPIO to mux register mapping.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sdp4430_uart_config isn't used anywhere, so remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add base address definations for new AM35xx IPSS modules, like
VPFE, USBOTG, CPGMAC.
Please note that the OMAP34xx IVA2 memory space is being used for
AM35xx IPSS modules.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Changes for setting the padconf value for sys_nirq line which is
connected to T2 INTR1. This will fix the T2 keypad wakeup.
Signed-off-by: Lesly A M <x0080970@ti.com>
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of the ifdeffery in omap_mux_init by creating
omap_mux_init_package and omap_mux_init_signals functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode. Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call the PM context-loss count function, now that there
is a prototype for it.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c. PBIAS and other system control
configuration remains in the board file.
Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined. That makes the
board initialisation now entirely independent of its original
twl4030 roots.
Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code. It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for flashes on 3430SDP boards. All three
NAND, NOR and OneNAND are supported. I have tested it on
3430SDP (ES2 and ES3.1).
This patch can be treated as an example to "how to utilize":
'gpmc-nand.c' and 'board-sdp-flash.c'.
Similar patches can be created for 2430sdp and 3630sdp or any other
similar board.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).
This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.
A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts
A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of the following warnings:
arch/arm/mach-omap2/gpmc.c:550:30: warning: non-ANSI
function declaration of function 'omap3_gpmc_save_context'
arch/arm/mach-omap2/gpmc.c:581:33: warning: non-ANSI
function declaration of function 'omap3_gpmc_restore_context'
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine cache size required per McBSP port at init time, based on
processor type running on.
Allocate space for storing cached copies of McBSP register values at
port request.
Modify omap_msbcp_write() function to update the cache with every
register write operation.
Modify omap_mcbsp_read() to support reading from cache or hardware.
Update MCBSP_READ() macro for modified omap_mcbsp_read() function API.
Introduce a new macro that reads from the cache.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with: omap_perseus2_730_defconfig, omap_generic_1610_defconfig,
omap_generic_2420_defconfig, omap_2430sdp_defconfig, omap_3430sdp_defconfig,
omap_4430sdp_defconfig with CONFIG_OMAP_MCBSP=y selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP based boards to use physmap-flash. Refreshed against today's
Linux omap kernel tree
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clkops_noncore_dpll_ops for omap3 and omap4.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow booting omap4 with multi-omap configuration.
Tested only on omap2 and omap3, please somebody test
on omap4 and ack.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move defines around and set up handlers based on MULTI_OMAP2.
Note that this will only allow compiling in omap4 with omap2 and
omap3. It will not yet make omap4 boot with multi-omap.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define the irq base the same way as for omap2 and omap3,
and start using get_irqnr_preamble.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make get_irqnr_and_base common for mach-omap2 multiboot
Thanks to a tip from Russell King <rmk+kernel@arm.linux.org.uk>,
this also optimizes the code for non-multiboot configurations by
using get_irqnr_preamble.
Note that this will only work currently for 24xx and 34xx.
Support for 44xx can be added later on for basic multiboot,
and similar patch should be done for mach-omap1/entry-macro.S.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
