The 8139 drivers are a source of error messages that confuse users.
Since this device can not be disambiguated by normal PCI device
id's two drivers match the same info. But the module utilities
seem to correctly handle this overlap, they try one driver, then
if that doesn't load try the other. Therefore there is no need for
a message to be logged with error level severity, just using info
level instead. Can't be completely silent because user might have
configure one driver and forgot the other one.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The write barrier should be used before starting a DMA transfer. This fixes
a problem, where almost all packets received on another machine had garbled
content. Tested with an RTL8100C on a MIPS machine.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I would like to submit a correction to the driver
drivers/net/8139too.c,
which in no way changes the compiled driver, but does change
the value of a previously incorrect value for the configuration
register address of Flash PROM on the network processor rtl8139C.
This corrected value is in accordance with the datasheet
for rtl8139C, and in addition this new value is indeed used
in other functional drivers that use this adapter for
programming a Flash memory chip in situ. But as said,
the two new constants are never referenced in the driver
maintained by you: they are only informational and correct!
Mats Erik Andersson, meand@users.sourceforge.net
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch uses netdev_alloc_skb. This sets skb->dev and allows
arch specific allocation. Also cleanup the alignment code.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The OQO model 2 has an RTL8139 from Atheros that doesn't like MMIO.
It fails on modprobe, with a 'PCI Bus error' message.
Force it to always use polled IO.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is needed to support devices that only work with PIO without
penalising devices that work fine with MMIO in distro kernels.
It also allows us to eventually use PIO as a fallback when setting
up MMIO fails.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
synchronize_irq() is superfluous when free_irq() call immediately follows it,
because free_irq() also does a synchronize_irq() call of its own.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the following errors and warnings reported by checkpatch.pl:
+ ERROR: Macros with complex values should be enclosed in parenthesis
+ WARNING: __func__ should be used instead of gcc specific __FUNCTION__
+ WARNING: plain inline is preferred over __inline__
+ WARNING: Use #include <linux/io.h> instead of <asm/io.h>
+ WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
The changes were verified with by comparing the "objdump -d 8139too.ko"
output which is exactly the same for the old and new version in case of
config CONFIG_8139TOO=m, CONFIG_8139TOO_PIO=n, CONFIG_8139TOO_TUNE_TWISTER=n,
CONFIG_8139TOO_8129=n, CONFIG_8139_OLD_RX_RESET=n.
Software versions used: gcc 4.2.3, objdump 2.18.0.20080103, on elf32-i386.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Updates the 8139too driver to work with recently added
(a724605cb7) declared coherent memory
patch for the Dreamcast.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* (main change) tab-align hardware register value enums, and hw struct
* MMIO_FLUSH_AUDIT_COMPLETE has been defined to 1 for a while. Remove
the code activated when it is set to zero.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It hasn't "summed" anything in over 7 years, and it's
just a straight mempcy ala skb_copy_to_linear_data()
so just get rid of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Your usual dont-flush_scheduled_work-with-RTNL-held stuff.
It is a bit different here since the thread runs permanently
or is only occasionally kicked for recovery depending on the
hardware revision.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
As I promised last week, here is the first pass at removing all
unnecessary printk's that exist in network device drivers currently in
promiscuous mode. The duplicate messages are not needed so they have
been removed. Some of these drivers are quite old and might not need an
update, but I did them all anyway.
I am currently auditing the remaining conditional printk's and will send
out a patch for those soon.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
> stack backtrace:
> [<f9099d31>] rtl8139_start_xmit+0xd9/0xff [8139too]
> [<c11ad5ea>] netpoll_send_skb+0x98/0xea
This seems to be a real deadlock...
So netpoll_send_skb takes the _xmit_lock, which is all nitty gritty
but then rtl8139_start_xmit comes around while that lock is taken, and
does
spin_unlock_irq(&tp->lock);
which.. enables interrupts and softirqs; this is quite bad because the
xmit lock is taken in softirq context for the watchdog like this:
[<c1200376>] _spin_lock+0x23/0x32
[<c11af282>] dev_watchdog+0x14/0xb1
[<c101dab2>] run_timer_softirq+0xf2/0x14a
[<c101a691>] __do_softirq+0x55/0xb0
[<c1004a8d>] do_softirq+0x58/0xbd
Which would deadlock now that the spin_unlock_irq() has enabled
irqs/softirqs while the _xmit_lock is still held.
The patch below turns this into a irqsave/irqrestore pair so that
interrupts don't get enabled unconditionally.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For messages prior to register_netdev(), prefer dev_printk() because
that prints out both our driver name and our [PCI | whatever] bus id.
Updates: 8139{cp,too}, b44, bnx2, cassini, {eepro,epic}100, fealnx,
hamachi, ne2k-pci, ns83820, pci-skeleton, r8169.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch turns the RTNL from a semaphore to a new 2.6.16 mutex and
gets rid of some of the leftover legacy.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo's stealth lock validator detected that both thread acquire
dev->xmit_lock and tp->rx_lock in reverse order.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The rtl8139 thread is triggered only on rare 8139 hardware, the race
itself is unlikely, and the impact of racing is low. We don't care
enough to create a more-complex race-free solution.
Rather, if the trylock fails, we now simply poll twice a second until
we do get the lock.
Gone are the days when 8139too was a shining example of how to use
kernel threads. Delayed workqueues are easier, and map precisely to
our task: running code from a kernel thread, after a periodic sleep.
Add "HasHltClk" flag for RTL-8100B/8139D hardware in order to fix
problems resuming from suspend-to-RAM.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
