There are a few issues found around the battery not being present. If the
battery isn't present, then a few undesirable things happen. The first was
excessive reporting of failed properties. This was fixed by instead
returning ENODATA for all properties other than PRESENT if the battery
isn't present. That way the callers can identify the difference between a
failure and the battery not being there.
The next issue was in the suspend logic. It was found that if the battery
wasn't present, then it would return a failure, preventing the system from
going into suspend. If there is no battery present, the io is expected to
fail, so in that case, we shouldn't return the failure and just
acknowledge that it was expected.
I also found that when a gpio was used, i didn't maintain the internal
is_present state properly. I added a set of that to fix that.
Lastly, the code to see io's fail and figure out that the battery isn't
present when not using a gpio had a problem. In that code, it looked for
the read to fail and if it did, then handled it. The problem is that in
function to get the property, it first writes a value and that write can
fail, causing the code to never reach the logic after the read. Fix is
to move the logic till after the write.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
PROP_STATUS property was not counted, as result VOLTAGE_MIN property is
missing in sysfs. Fix it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:aer915 z2_battery
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entries will be added to
modules.alias:
alias i2c:ds2786 ds2782_battery
alias i2c:ds2782 ds2782_battery
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The device table is required to load modules based on modaliases.
After adding the MODULE_DEVICE_TABLE, below entry will be added to
modules.alias:
alias i2c:bq20z75 bq20z75
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
With the support of platform data, now adding support for option i2c
retries on read/write failures. Ths is specified through the optional
platform data.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Adding support for an optional gpio for battery detection. This is
passed in through the i2c platform data. It also accepts another
field, battery_detect_present to signify the gpio state which means
the battery is present, either 0 (low) or 1 (high).
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This queues work from the otg notification where the
i2c operations can be safely made. Needed for atomic otg
notifiers.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Doing this by using 2 calls sometimes results in unexpected
values being returned on OMAP3 i2c controller.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
* Consistently use uppercase for hexadecimal values.
* Clarify/fix the unit of functions return value in its comment.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
The current code only reports whether the battery is charging or
discharging. But the battery also reports whether it is fully charged,
furthermore by look at if the battery is supplied we can tell whether it
is discharging or not charging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds support for polling the battery state and generating a
power_supply_changed() event if it has changed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds a register cache to the bq27x00 battery driver.
Usually multiple, if not all, power_supply properties are queried at once,
for example when an uevent is generated. Since some registers are used by
multiple properties caching the registers should reduce the number of
reads.
The cache is valid for 5 seconds this roughly matches the internal update
interval of the current register for the bq27000/bq27200.
Fast changing properties(*_NOW) which can be obtained by reading a single
register are not cached.
It will also be used in the follow up patch to check if the battery status
has been changed since the last update to emit power_supply_changed events.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds support for the bq27000 battery to the bq27x00 driver.
The bq27000 is similar to the bq27200 except that it uses the HDQ bus
instead of I2C to communicate with the host system.
The driver is implemented as a platform driver. The driver expects to be
provided with a read callback function through its platform data. The read
function is assumed to do the lowlevel HDQ handling and read out the value
of a certain register.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch simplifies the drivers data structure and moves code to be
shared by the bq27000 and bq27200/bq27500 init functions into a common
function.
This patch has no functional changes, it only moves code around.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch changes get_property callback of the bq27x00 battery to return
-ENODEV for properties other then the PROP_PRESENT if the battery is not
present.
The power subsystem core expects a driver to behave that way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
According to the bq27000 datasheet the current should be calculated by
the following formula:
current = AI * 3570 / 20
This patch adjust the drivers code accordingly.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch improves the precession of the temperature property of the
bq27x00 driver.
By dividing before multiplying the current code effectively cuts of the
last decimal digit. This patch fixes it by multiplying before dividing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds the type property to the bq27x00 battery driver.
All bq27x00 are lithium ion batteries.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Calling device_add causes an inital uevent for that device to be generated.
The power_supply uevent function calls the drivers get_property function,
which might causes the driver to update its state, which again might
causes the driver to call power_supply_changed(). Since the power_supplys
changed_work has not been initialized at this point the behavior is
undefined and can result in an OOPS.
This patch fixes the issue by initializing the power_supplys changed_work
prior to adding the power_supplys device to the device tree.
Reported-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Sometimes a driver can not report a meaningful value for a certain property
and returns -ENODATA.
Currently when generating a uevent and a property return -ENODATA it is
treated as an error an no uevent is generated at all. This is not an
desirable behavior.
This patch adds a special case for -ENODATA and ignores properties which
return this error code when generating the uevent.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Add new trigger to power_supply LEDs. It will blink when battery is
charging, and stay solid when battery is charged. It's usefull to
indicate battery state when there's only one LED available.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Adding support for charge properties for gas gauge.
Also ensuring that battery mode is correct now for energy as well as
charge properties by setting it on the fly.
I also added 2 functions to power_supply.h to help identify the units for
specific properties more easily by power supplies.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* git://git.infradead.org/battery-2.6: (21 commits)
power_supply: Add MAX17042 Fuel Gauge Driver
olpc_battery: Fix up XO-1.5 properties list
olpc_battery: Add support for CURRENT_NOW and VOLTAGE_NOW
olpc_battery: Add support for CHARGE_NOW
olpc_battery: Add support for CHARGE_FULL_DESIGN
olpc_battery: Ambient temperature is not available on XO-1.5
jz4740-battery: Should include linux/io.h
s3c_adc_battery: Add gpio_inverted field to pdata
power_supply: Don't use flush_scheduled_work()
power_supply: Fix use after free and memory leak
gpio-charger: Fix potential race between irq handler and probe/remove
gpio-charger: Provide default name for the power_supply
gpio-charger: Check result of kzalloc
jz4740-battery: Check if platform_data is supplied
isp1704_charger: Detect charger after probe
isp1704_charger: Set isp->dev before anything needs it
isp1704_charger: Detect HUB/Host chargers
isp1704_charger: Correct length for storing model
power_supply: Add gpio charger driver
jz4740-battery: Protect against concurrent battery readings
...
The MAX17042 is a fuel gauge with an I2C interface for lithium-ion
betteries. Unlike its predecessor MAX17040, MAX17042 uses 16bit
registers. Besides, MAX17042 has much more features than MAX17040; e.g.,
a thermistor, current and current accumulation measurement, battery
internal resistance estimate, average values of measurement, and others.
This patch implements a driver for MAX17042.
In this initial release, we have implemented the most basic features of
a fuel gauge: measure the battery capacity and voltage.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The patches adding support for CURRENT_NOW, VOLTAGE_NOW, CHARGE_NOW and
CHARGE_FULL_DESIGN were based on a tree not including c566d299
("olpc_battery: Ambient temperature is not available on XO-1.5") and
therefore only modified the then-common, now-XO-1 properties list. This
patch adds the new properties to XO-1.5 as well.
Signed-off-by: Sascha Silbe <sascha-pgp@silbe.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
{CURRENT,VOLTAGE}_AVG are actually {CURRENT,VOLTAGE}_NOW (the EC code
directly passes through the value from the gas gauge instead of the
internally used average). We retain {CURRENT,VOLTAGE}_AVG as an alias
for compatibility reasons, it will be removed later.
Signed-off-by: Sascha Silbe <sascha-pgp@silbe.org>
[ pgf@laptop.org: added VOLTAGE_NOW, aliased to VOLTAGE_AVG ]
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
CHARGE_NOW is needed by some user space software (read: UPower) for
internal calculations.
This patch violates the power supply class definition (as we already
do for CAPACITY though it isn't as obvious there), but this is the best
we can do without adding rather sophisticated algorithms to either the EC
or UPower.
Signed-off-by: Sascha Silbe <sascha-pgp@silbe.org>
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Some user space software (read: UPower) uses CHARGE_FULL_DESIGN for internal
calculations. The design capacity of the OLPC batteries is effectively fixed
and only needs to be exported.
Signed-off-by: Sascha Silbe <sascha-pgp@silbe.org>
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The XO-1.5 does not support the ambient temperature property.
Create a separate list of properties for that configuration where
ambient temperature is not included, and apply the correct property
list at runtime.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
During test-build (with disabled 'depends on') I found that
jz4740-battery driver lacks linux/io.h, which makes build break
like this (on x86):
CC [M] drivers/power/isp1704_charger.o
jz4740-battery.c: In function 'jz_battery_read_voltage':
jz4740-battery.c:84: error: implicit declaration of function 'readw’
jz4740-battery.c: In function 'jz_battery_probe':
jz4740-battery.c:284: error: implicit declaration of function 'ioremap_nocache’
jz4740-battery.c:285: warning: assignment makes pointer from integer without a cast
jz4740-battery.c:372: error: implicit declaration of function 'iounmap'
make[2]: *** [drivers/power/jz4740-battery.o] Error 1
This patch fixes the issues, and thus makes it easier to build-test
the driver for me.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Add support for inverted gpio_charge_finished values.
This change is necessary for H1940 support.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
flush_scheduled_work() is deprecated and scheduled to be removed.
In battery drivers, the work can be canceled on probe failure and
removal and should be flushed on suspend. Replace
flush_scheduled_work() usages with direct cancels and flushes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
device_unregister() might free its argument. This leads to freed
memory use in kfree(). Also use put_device() instead of kfree()
as dev may be already used in another layer after call to device_add().
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch fixes a potential race between the irq handler and the probe
and remove functions.
The irq should not be requested before the chargers power_supply has been
registered and has to be freed before the power_supply is unregistered,
otherwise it is possible that the irq fires while the power_supply is not
initialized yet or has already been freed.
While we are at it replace request_irq with request_any_context_irq.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch sets a default name for the power_supply in case there was
no name supplied through the platform_data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Since kzalloc can return NULL we have to check its result.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
Currently platform_data is dereferenced without checking whether it
is actually set, which can lead to kernel crashes.
This patch adds a check which will abort the drivers probe function
gracefully if no platform_data is supplied.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If the device is booted up with cable connected, or the
module is loaded after plugging in the cable, the
notification has come and gone, so not relying on it at
probe time. Instead this checks the VBUS level manually
after probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
isp1704_test_ulpi() is the first place that needs isp->dev
member, so it must be set before calling the function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
To avoid breaking high speed chirp handshaking with CDP
chargers, no more then 500mA should be drawn. To make sure
of this, utilizing current_max property. After the device
has enumerated, it's safe to draw the maximum 1800mA as
defined in the Battery Charging Specification. This can be
also used with normal USB connection if the controller sends
ENUMERATED notification with the milliamps as data.
From now on the online property indicates VBUS, present
property if there is a charger and current_max the milliamps
possible to draw from VBUS.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Model should have room to accommodate the trailing null byte,
"isp170[4|7]\0".
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds a simple driver for chargers indicating their online
status through a GPIO pin.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>