1
Commit Graph

14501 Commits

Author SHA1 Message Date
Ron Mercer
a5f59dc926 qlge: Clear frame to queue routing before reset.
Not clearing the routing bits can cause frames to erroneously get routed to
management processor.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:21 -07:00
Ron Mercer
4322c5bee8 qlge: Expand coverage of hw lock for config register.
The hardware semaphore covers the configuration register as well as the
ICB registers.  The ICB high and low regs contain the address of the
initialization control block and the config register is used to signal
the hardware that a block is ready to be downloaded.  Currently we were
only protecting the ICB regs.  This changes expands to cover the config
register as well.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03 19:10:18 -07:00
Wade Farnsworth
42caa07404 phylib: fixes for PHY_RESUMING state changes
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING.  Add a call to phy_read_status() to
update the link before entering PHY_RUNNING.  If the link is not up at
this point, enter the PHY_NOLINK state instead.

Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing.  Add the calls
similar to the other transitions to PHY_RUNNING.

Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:55 -07:00
Dhananjay Phadke
67c38fc61a netxen: avoid frequent firmware reset
Restrict firmware reset to following cases -

o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.

This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:51 -07:00
Dhananjay Phadke
98e31bb009 netxen: fix the version code macro
Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.

Also fix a infinite loop when cut-thru file firmware is
invalid.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-02 13:16:49 -07:00
Alexander Duyck
59ed6eecff igb: return PCI_ERS_RESULT_DISCONNECT on permanent error
PCI drivers that implement the io_error_detected callback should return
PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure.  This patch fixes the issue for igb.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:04 -07:00
Mike Mason
c93b5a76d5 e1000e: io_error_detected callback should return PCI_ERS_RESULT_DISCONNECT
on permanent failure

PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is not
checked in many of the network drivers.

This patch fixes the omission in the e1000e driver.

Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:02 -07:00
Andre Detsch
eab633021c e1000: return PCI_ERS_RESULT_DISCONNECT on permanent error
PCI drivers that implement the io_error_detected callback
should return PCI_ERS_RESULT_DISCONNECT if the state
passed in is pci_channel_io_perm_failure.  This state is
not checked in many of the network drivers.

The patch fixes the omission in the e1000 driver.

Based on Mike Mason's similar patch for e1000e.

Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
CC: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:47:00 -07:00
Jesse Brandeburg
679be3ba0c e1000: fix unmap bug
as reported by kerneloops.org

[  121.781161] ------------[ cut here ]------------
[  121.781171] WARNING: at lib/dma-debug.c:793 check_unmap+0x14e/0x577()
[  121.781173] Hardware name: S5520HC
[  121.781177] e1000 0000:0a:00.0: DMA-API: device driver tries to free DMA
memory it has not allocated [device address=0x00000001d688b0fa] [size=1522
bytes]
[  121.781180] Modules linked in: e1000 mdio  dca [last unloaded: ixgbe]
[  121.781187] Pid: 4793, comm: bash Tainted: P 2.6.30-master-06161113 #3
[  121.781190] Call Trace:
[  121.781195]  [<ffffffff8123056f>] ? check_unmap+0x14e/0x577
[  121.781201]  [<ffffffff81057a19>] warn_slowpath_common+0x77/0x8f
[  121.781205]  [<ffffffff81057ae1>] warn_slowpath_fmt+0x9f/0xa1
[  121.781212]  [<ffffffff81477ce2>] ? _spin_lock_irqsave+0x3f/0x49
[  121.781216]  [<ffffffff8122fa97>] ? get_hash_bucket+0x28/0x33
[  121.781220]  [<ffffffff8123056f>] check_unmap+0x14e/0x577
[  121.781225]  [<ffffffff810e4f48>] ? check_bytes_and_report+0x38/0xcb
[  121.781230]  [<ffffffff81230bbf>] debug_dma_unmap_page+0x80/0x92
[  121.781234]  [<ffffffff8122e549>] ? unmap_single+0x1a/0x4e
[  121.781239]  [<ffffffff813901e1>] ? __kfree_skb+0x74/0x78
[  121.781250]  [<ffffffffa00662ef>] pci_unmap_single+0x64/0x6d [e1000]
[  121.781259]  [<ffffffffa0066344>] e1000_clean_rx_ring+0x4c/0xbf [e1000]
[  121.781268]  [<ffffffffa00663df>] e1000_clean_all_rx_rings+0x28/0x36 [e1000]
[  121.781277]  [<ffffffffa0067464>] e1000_down+0x138/0x141 [e1000]
[  121.781286]  [<ffffffffa00681c2>] __e1000_shutdown+0x6b/0x198 [e1000]
[  121.781296]  [<ffffffffa0068405>] e1000_suspend+0x17/0x50 [e1000]
[  121.781301]  [<ffffffff81237665>] pci_legacy_suspend+0x3b/0xbe
[  121.781305]  [<ffffffff81237bc6>] pci_pm_suspend+0x3e/0xf1
[  121.781310]  [<ffffffff812eaf1c>] pm_op+0x57/0xde
[  121.781314]  [<ffffffff812eb444>] dpm_suspend_start+0x31e/0x470
[  121.781319]  [<ffffffff810877da>] suspend_devices_and_enter+0x3e/0x1a2
[  121.781323]  [<ffffffff81087a0f>] enter_state+0xd1/0x127
[  121.781327]  [<ffffffff8108717a>] state_store+0xa7/0xc9
[  121.781332]  [<ffffffff81221843>] kobj_attr_store+0x17/0x19
[  121.781336]  [<ffffffff8113c01e>] sysfs_write_file+0xe5/0x121
[  121.781341]  [<ffffffff810ed165>] vfs_write+0xab/0x105
[  121.781344]  [<ffffffff810ed279>] sys_write+0x47/0x6d
[  121.781349]  [<ffffffff81027aab>] system_call_fastpath+0x16/0x1b
[  121.781352] ---[ end trace 97bacaaac2ed7786 ]---

Fix is to correctly zero out internal ->dma value when unmapping
and make sure never to unmap unless there specifically was a mapping done.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:58 -07:00
Jesse Brandeburg
91615f765a igb: fix unmap length bug
driver was mixing NET_IP_ALIGN count bytes in map/unmap calls
unevenly. Only map the bytes that the hardware might dma into

also fix unmap related bug where ->dma was not being cleared
after unmap

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:57 -07:00
Jesse Brandeburg
4f57ca6e17 ixgbe: fix unmap length bug
This patch addresses three WARN_ON statements from DMA-API debug code

ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.

found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.

in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single

and lastly, don't unmap (half) pages that aren't mapped.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:54 -07:00
Mallikarjuna R Chilakala
a1f25324b9 ixgbe: Fix link capabilities during adapter resets
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:53 -07:00
Mallikarjuna R Chilakala
a380137900 ixgbe: Fix device capabilities of 82599 single speed fiber NICs.
82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.

Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:53 -07:00
Don Skidmore
88d2b81f4e ixgbe: Fix SFP log messages
We had a wide range of log messages for the same sort of SFP
failure.  This patch makes them all more similar and less
confusing along with converting them to dev_err.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:51 -07:00
Herbert Xu
7963837f93 usbnet: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:48 -07:00
Herbert Xu
80667ac13a smsc95xx: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:46 -07:00
Herbert Xu
58e2e7d591 rndis_host: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:45 -07:00
Herbert Xu
a22d2b36a2 net1080: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:43 -07:00
Herbert Xu
9612101cb3 dm9601: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:43 -07:00
Herbert Xu
eaea43abf3 cdc_eem: Use netdev stats structure
Now that netdev has its own stats structure we should use that
instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 19:46:41 -07:00
Naohiro Ooiwa
01e5329814 bnx2x: Fix the behavior of ethtool when ONBOOT=no
This is the same fix as commit
7959ea254e ("bnx2: Fix the behavior of
ethtool when ONBOOT=no"), but for bnx2x:

--------------------
    When configure in ifcfg-eth* is ONBOOT=no,
    the behavior of ethtool command is wrong.
    
        # grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
        ONBOOT=no
        # ethtool eth2 | tail -n1
                Link detected: yes
    
    I think "Link detected" should be "no".
--------------------

Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30 12:44:19 -07:00
Graf Yang
d51e9b0d94 net/irda: convert bfin_sir to net_device_ops
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-29 19:41:49 -07:00
Ajit Khaparde
bd46cb6cf1 be2net: Fix to avoid a crash seen on PPC with LRO and Jumbo frames.
While testing the driver on PPC, we ran into a crash with LRO, Jumbo frames.
With CONFIG_PPC_64K_PAGES configured (a default in PPC), MAX_SKB_FRAGS drops to 3 and we were crossing the array limits on skb_shinfo(skb)->frags[].
Now we coalesce the frags from the same physical page into one slot in
skb_shinfo(skb)->frags[] and go to the next index when the frag is from

different physical page.

This patch is against the net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-28 17:34:25 -07:00
Anton Vorontsov
b9389796fa sky2: Fix checksum endianness
sky2 driver on PowerPC targets floods kernel log with following errors:

  eth1: hw csum failure.
  Call Trace:
  [ef84b8a0] [c00075e4] show_stack+0x50/0x160 (unreliable)
  [ef84b8d0] [c02fa178] netdev_rx_csum_fault+0x3c/0x5c
  [ef84b8f0] [c02f6920] __skb_checksum_complete_head+0x7c/0x84
  [ef84b900] [c02f693c] __skb_checksum_complete+0x14/0x24
  [ef84b910] [c0337e08] tcp_v4_rcv+0x4c8/0x6f8
  [ef84b940] [c031a9c8] ip_local_deliver+0x98/0x210
  [ef84b960] [c031a788] ip_rcv+0x38c/0x534
  [ef84b990] [c0300338] netif_receive_skb+0x260/0x36c
  [ef84b9c0] [c025de00] sky2_poll+0x5dc/0xcf8
  [ef84ba20] [c02fb7fc] net_rx_action+0xc0/0x144

The NIC is Yukon-2 EC chip revision 1.

Converting checksum field from le16 to CPU byte order fixes the issue.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-26 09:28:42 -07:00
Nicolas Reinecke
30767636e5 mdio add missing GPL flag
Add missing GPL flag and description.

mdio: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint

Signed-off-by: Nicolas Reinecke <nr <at> das-labor.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25 20:06:34 -07:00
roel kluin
37c8ae3acf sh_eth: remove redundant test on unsigned
Unsigned boguscnt cannot be less than 0.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25 20:03:56 -07:00
Ionut Nicu
e2a61fa313 fsl_pq_mdio: Fix fsl_pq_mdio to work with modules
This patch fixes the case when ucc_geth or gianfar are compiled
as modules. Without this patch the call to phy_connect() fails.

Signed-off-by: Ionut Nicu <ionut.nicu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25 20:03:53 -07:00
Brandon Philips
d8146bb23e atl1*: add device_set_wakeup_enable to atl1*_set_wol
Tell PCI core that atl1* device can wakeup the system when WOL is
enabled by calling device_set_wakeup_enable.

Joerg noted that his atl1e device WOL fine after enabling it with
ethtool and changing /sys/class/net/eth0/device/power/wakeup to enabled
Tested on atl1e: https://bugzilla.novell.com/show_bug.cgi?id=493214

Tested by: Joerg Reuter <jreuter@novell.com>
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25 02:58:17 -07:00
David S. Miller
11687a1099 Revert "veth: prevent oops caused by netdev destructor"
This reverts commit ae0e8e8220.

This change had two problems:

1) Since it frees the stats in the drivers' close method, we
   can OOPS in the transmit routine.

2) stats are no longer remembered across ifdown/ifup which
   disagrees with how every other device operates.

Thanks to analysis and test patch from Serge E. Hallyn
and initial OOPS report by Sachin Sant.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-25 02:45:42 -07:00
Florian Fainelli
6a9b654616 cpmac: fix compilation failure introduced with netdev_ops conversion
This patch fixes and obvious typo in the netdev_ops initialization:
ndo_so_ioctl should be ndo_do_ioctl.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-24 18:03:11 -07:00
Linus Torvalds
09ce42d316 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6:
  bnx2: Fix the behavior of ethtool when ONBOOT=no
  qla3xxx: Don't sleep while holding lock.
  qla3xxx: Give the PHY time to come out of reset.
  ipv4 routing: Ensure that route cache entries are usable and reclaimable with caching is off
  net: Move rx skb_orphan call to where needed
  ipv6: Use correct data types for ICMPv6 type and code
  net: let KS8842 driver depend on HAS_IOMEM
  can: let SJA1000 driver depend on HAS_IOMEM
  netxen: fix firmware init handshake
  netxen: fix build with without CONFIG_PM
  netfilter: xt_rateest: fix comparison with self
  netfilter: xt_quota: fix incomplete initialization
  netfilter: nf_log: fix direct userspace memory access in proc handler
  netfilter: fix some sparse endianess warnings
  netfilter: nf_conntrack: fix conntrack lookup race
  netfilter: nf_conntrack: fix confirmation race condition
  netfilter: nf_conntrack: death_by_timeout() fix
2009-06-24 10:01:12 -07:00
Ooiwa Naohiro
7959ea254e bnx2: Fix the behavior of ethtool when ONBOOT=no
I found a little bug.

When configure in ifcfg-eth* is ONBOOT=no,
the behavior of ethtool command is wrong.

    # grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
    ONBOOT=no
    # ethtool eth2 | tail -n1
            Link detected: yes

I think "Link detected" should be "no".

Signed-off-by: Ooiwa Naohiro <nooiwa@miraclelinux.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-24 00:19:06 -07:00
Ron Mercer
0f77ca928b qla3xxx: Don't sleep while holding lock.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 16:36:27 -07:00
Ron Mercer
e5a673742e qla3xxx: Give the PHY time to come out of reset.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 16:36:26 -07:00
Linus Torvalds
32708e8e95 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA: Add __init/__exit macros to addr.c and cma.c
  IB/ehca: Bump version number
  mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
  IB/mthca: Replace dma_sync_single() use with proper functions
  RDMA/nes: Fix FIN state handling under error conditions
  RDMA/nes: Fix max_qp_init_rd_atom returned from query device
  IB/ehca: Ensure that guid_entry index is not negative
  IB/ehca: Tolerate dynamic memory operations before driver load
2009-06-23 11:36:01 -07:00
Linus Torvalds
f5bcf5f447 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (38 commits)
  fusion: mptsas, fix lock imbalance
  [SCSI] scsi_transport_fc: replace BUS_ID_SIZE by fixed count
  sd, sr: fix Driver 'sd' needs updating message
  scsi_transport_iscsi: return -EOVERFLOW for Too many iscsi targets
  fc_transport: Selective return value from BSG timeout function
  fc_transport: The softirq_done function registration for BSG request
  sym53c8xx: ratelimit parity errors
  explain the hidden scsi_wait_scan Kconfig variable
  ibmvfc: Fix endless PRLI loop in discovery
  ibmvfc: Process async events before command responses
  libfc: Add runtime debugging with debug_logging module parameter
  libfcoe: Add runtime debugging with module param debug_logging
  fcoe: Add runtime debug logging with module parameter debug_logging
  scsi_debug: Add support for physical block exponent and alignment
  cnic: add NETDEV_1000 and NETDEVICES to Kconfig select
  cnic: Fix __symbol_get() build error.
  Revert "[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’"
  ipr: differentiate pci-x and pci-e based adapters
  ipr: add test for MSI interrupt support
  scsi_transport_spi: Blacklist Ultrium-3 tape for IU transfers
  ...
2009-06-23 11:35:37 -07:00
Heiko Carstens
0cf08dcb78 net: let KS8842 driver depend on HAS_IOMEM
Fixes this compile error on s390:

  CC      drivers/net/ks8842.o
drivers/net/ks8842.c: In function 'ks8842_select_bank':
drivers/net/ks8842.c:124: error: implicit declaration of function 'iowrite16'
drivers/net/ks8842.c: In function 'ks8842_write8':
drivers/net/ks8842.c:131: error: implicit declaration of function 'iowrite8'

Cc: Richard Rojfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 04:16:44 -07:00
Heiko Carstens
fec37ab56f can: let SJA1000 driver depend on HAS_IOMEM
Fixes this compile error on s390:

drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_read_reg':
drivers/net/can/sja1000/sja1000_platform.c:42: error: implicit declaration of function 'ioread8'
drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_write_reg':
drivers/net/can/sja1000/sja1000_platform.c:47: error: implicit declaration of function 'iowrite8'
drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_probe':
drivers/net/can/sja1000/sja1000_platform.c:79: error: implicit declaration of function 'ioremap_nocache'

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 04:16:44 -07:00
Dhananjay Phadke
96f2ebd2e1 netxen: fix firmware init handshake
Make sure all functions run firmware init handshake.

If PCI function 0 fails to initialize firmware, mark the
state failed so that other functions on the same board
bail out quickly instead of waiting 30s for firmware
handshake.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 04:16:43 -07:00
Dhananjay Phadke
01542cd1bb netxen: fix build with without CONFIG_PM
wrap pci suspend() and resume() with CONFIG_PM check.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-23 04:16:42 -07:00
Roland Dreier
e727f5cde9 mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
Commit 5d23a1d2 ("net: replace dma_sync_single with
dma_sync_single_for_cpu") replaced uses of the deprectated function
dma_sync_single() with calls to dma_sync_single_for_cpu().  However,
to be correct, the code should do a sync for_cpu() before touching the
memory and for_device() after it's done.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-06-22 23:07:56 -07:00
Linus Torvalds
f39cf0b783 Merge git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6:
  xtensa: enable m41t80 driver in s6105_defconfig
  xtensa: add m41t62 rtc to s6105 platform
  xtensa: enable s6gmac in s6105_defconfig
  xtensa: s6105 specific configuration for s6gmac
  s6gmac: xtensa s6000 on-chip ethernet driver
  xtensa: support s6000 gpio irqs and alternate function selection
  xtensa: s6000 dma engine support
  xtensa: allow variant to initialize own irq chips
  xtensa: cache inquiry and unaligned cache handling functions
2009-06-22 12:38:31 -07:00
Linus Torvalds
5165aece0e Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (43 commits)
  via-velocity: Fix velocity driver unmapping incorrect size.
  mlx4_en: Remove redundant refill code on RX
  mlx4_en: Removed redundant check on lso header size
  mlx4_en: Cancel port_up check in transmit function
  mlx4_en: using stop/start_all_queues
  mlx4_en: Removed redundant skb->len check
  mlx4_en: Counting all the dropped packets on the TX side
  usbnet cdc_subset: fix issues talking to PXA gadgets
  Net: qla3xxx, remove sleeping in atomic
  ipv4: fix NULL pointer + success return in route lookup path
  isdn: clean up documentation index
  cfg80211: validate station settings
  cfg80211: allow setting station parameters in mesh
  cfg80211: allow adding/deleting stations on mesh
  ath5k: fix beacon_int handling
  MAINTAINERS: Fix Atheros pattern paths
  ath9k: restore PS mode, before we put the chip into FULL SLEEP state.
  ath9k: wait for beacon frame along with CAB
  acer-wmi: fix rfkill conversion
  ath5k: avoid PCI FATAL interrupts by restoring RETRY_TIMEOUT disabling
  ...
2009-06-22 11:57:09 -07:00
Alan Cox
a6540f731d ppp: Fix throttling bugs
The ppp layer goes around calling the unthrottle method from non sleeping
paths. This isn't safe because the unthrottle methods in the tty layer need
to be able to sleep (consider a USB dongle).

Until now this didn't show up because the ppp layer never actually throttled
a port so the unthrottle was always a no-op. Currently it's a mutex taking
path so warnings are spewed if the unthrottle occurs via certain paths.

Fix this by removing the unneccessary unthrottle calls.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-22 11:32:24 -07:00
Oskar Schirmer
8b0215aa5b s6gmac: xtensa s6000 on-chip ethernet driver
The s6000 on-chip MAC supports 10/100/1000Mbit and is connected to an
external PHY via MII or RGMII interface.

[jw@emlix.com: don't use device->bus_id directly]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glockner <dg@emlix.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
2009-06-22 02:37:34 -07:00
Dave Jones
f6b24caaf9 via-velocity: Fix velocity driver unmapping incorrect size.
When a packet is greater than ETH_ZLEN, we end up assigning the
boolean result of a comparison to the size we unmap.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 22:42:30 -07:00
Yevgeny Petrilin
0314db69d7 mlx4_en: Remove redundant refill code on RX
Our RX rings are always full, there is no need to check whether
we need to fill them or not. If we fail to allocate a new socket
buffer, the incoming packet is dropped an the ring remains full.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:07 -07:00
Yevgeny Petrilin
7237b40055 mlx4_en: Removed redundant check on lso header size
This check that verifies that the LSO header along with control
segment and first data segment do not cross 128 bytes is no longer
required.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:06 -07:00
Yevgeny Petrilin
3c05f5ef7c mlx4_en: Cancel port_up check in transmit function
When closing the port, we stop all transmit queues under the transmit
lock. It ensures that we will not attempt to transmit new packets after
the physical port was closed.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:05 -07:00
Yevgeny Petrilin
a11faac79f mlx4_en: using stop/start_all_queues
After we moved to be a multi queue device, need to stop/start
all of our transmit queues.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-21 19:18:04 -07:00