This patch moves the entry for the Gigabyte K8N51 from the 6stack
grouping to the 6stack-digout grouping, allowing for S/PDIF output
functionality.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the model entry (model=hippo) for Sony UX-90s with ALC262 codec.
Although the device has no SPDIF output, the hippo model adds a
PCM output, but it must be harmless.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
We need to enable External Amplifier on this laptops. This patch basicly
adds laptop-eapd model to ALC883 codec.
Signed-off-by: Andrew L. Neporada <nepal@asplinux.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for Asus laptops (for example: Asus
A6Rp-AP002).
Signed-off-by: Mariusz Domanski <mariook@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Changes from Realtek driver:
- New models hippo and hippo_1 for ALC262
- New models tagra-dig and tagra-2ch-dig for ALC883
- New id for ALC660 codec chip
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for Toshiba laptops. Code is from
RealTek's alsa-driver-1.0.12-4.05b tree.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds audio support for Medion's line of laptops,
based on code shipped with the laptops. Microphone support is
still being explored.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix wrong error checks of *_ch_mode_put() in patch_realtek.c and
patch_analog.c. snd_hda_ch_mode_put() could return a positive
value for success, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The PCI sub-device ID for the HP xw4400 is actually 0x280c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed the assignment of PCM devices for Realtek codecs.
The secondary analog capture should be statically asigned to the
third device regardless whether SPDIF exists or not.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds a couple of device ids for Acer laptops. In both cases,
the owners got the driver working by adding 'model=acer' to their
modprobe.conf files.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some machines have multiple headpohne pins (usually on the lpatop
and on the docking station) while the current hda-codec driver
assumes a single headphone pin. Now it supports multiple hp pins
(at least for detection).
The sigmatel 92xx code supports this new multiple hp pins.
It detects all hp pins for auto-muting, too.
Also, the driver checks speaker pins in addition. In some cases,
all line-out, speaker and hp-pins coexist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Assign the SPDIF always to the secondary device (dev#1) to keep
the same configuration. Move the optional capture device to the
third device (dev#2).
hda_intel now just ignores the NULL entries in the pcm arrays
from codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the support for LG LW25 laptop with ALC880 codec.
It's the same codec model as LG LW20 (model=lg-lw).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Patch enables the internal speaker on acer laptops with ALC883.
Signed-off-by: Vladimir Avdonin <vldmrrr@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds missing device ids for Intel 915 and D102GGC
motherboards.
Signed-off-by: Tobin Davis <tobinx.b.davis@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added missing TLV callbacks for HD-audio codec supports.
Also cleaned up the tlv callback for ad1986a (no mutex is needed there).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new model 'uniwill-m31' for Uniwill laptops with ALC861
codec chip. The patch is taken from ALSA bug#2035, and modifeid.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support in ALSA snd-hda-intel driver for Asus W6A
motherboard as reported in MDV Bugzilla #19962
(see http://qa.mandriva.com/show_bug.cgi?id=19962)
Signed-off-by: Danny Tholen <danny@mailmij.org>
Signed-off-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: Thierry Vignaud <tvignaud@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed the preselected model for a HP machine with SSID 103c:3010
to use hp-3013 (ALSA bug#2157).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Fix the wrong initialization of num_dacs when changing the channel
mode between 2 and multi-channel modes. It must be evaluated
after calling snd_hda_ch_mode_put()
- Added the similar check of num_dacs fix in Realtek code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Added model=arima for Arima W820Di1 with ALC882 codec chip
- Added EAPD-control verbs to TCL S700 init verbs
- Added missing model strings for Realtek codecs (to be specified
via module option explicitly for testing/debugging)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the support of Benq laptop with ALC262 codec.
A model string 'benq' is added, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the proper model entry for Clevo m665n laptop with ALC880 codec.
Also, added a model string 'clevo' to enable the clevo-type model option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Patch from Realtek:
- Fix ALC883 support code
- Add support of ALC888 codec
- Add ALC660 support (ALC861-compatible)
- Add HP xw4400/6400/8400/9400 support (model=hp-bpc)
- Code clean-up: fix spaces and indentation
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Changed the assigned model for HP dc7600 with ALC260 codec
to match better with the actual I/O assignment.
Patch taken from ALSA bug#2157.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the basic init verbs for ALC260 instead of hp init verbs
since hp init verbs seem incomplete and not working on some machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed the handling of capture controls on ALC882 3/6-stack models.
Now the driver checks the availability of NID 07h.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the model entry for Sony Vaio VGN-A790 laptop with ALC260 codec.
From: Kenneth Crudup <kenny@panix.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following patch relative to CVS from 20060324 adds the following
features to the Realtek HDA codec.
1) Define two new pin modes: ALC_PIN_DIR_IN_NOMICBIAS and
ALC_PIN_DIR_INOUT_NOMICBIAS. These can be used with jack mode switch
definitions in mixers to prevent the user being offered the mic bias
options if the hardware doesn't support it.
2) Add the ability to have different input mux definitions for different
ADCs. This is needed because the ALC260 chip uses different mux layouts
for the two onboard ADCs. A new field (num_mux_defs) was added to the
alc_spec and alc_config_preset structures to support this.
3) Adjust numerous comments to make them consistent with the above changes.
4) Utilise the new multi-mux definition functionality for the ALC260 fujitsu
model to allow recording of the mixer output.
5) Utilise the new multi-mux definition functionality for the ALC260 test
model to make the mux selections a little less confusing.
6) Allow the headphone jack of the ALC260 acer model to be retasked in
the mixer.
6) Utilise the new multi-mux definition functionality for the ALC260 acer
model to give access to the mixer output and the retasked headphone
jack.
At this stage the *_NOMICBIAS modes are not used. We have reports that the
"Line" jack of at least some Acer models doesn't pass the bias out, and we
also know that NIDs 0x0f and 0x10 don't seem to accept the mic bias requests
at all. However, I feel we need to collect more evidence on both counts
before committing to the use of *_NOMICBIAS. In the case of the Acers, it's
not clear whether this issue (probably caused by the inclusion of DC
blocking capacitors) affects all Acer models or just a small number. With
the issue with NIDs 0x0f and 0x10 it's unclear whether this is a hardware
bug which will be addressed in later chip revisions or if it's an
intentional restriction. The datasheet makes no mention of the restriction
so at this stage I'm inclined to consider it a hardware bug. Comments in
the source reflect this reasoning.
On a similar theme, the headphone jack of the Fujitsu S7020 also doesn't
appear to pass mic bias voltage. I'm still investigating this however.
With the ability to retask the headphone jack, owners of ALC260-based Acer
laptops should now be able to record 4 channels of audio if they desire. The
multiple mux definitions allow this jack to be presented from both ADCs
(since this mux input is one of those which differs between the muxes).
This patch has been tested on a Fujitsu S7020 laptop and appears to behave
itself both for the "test" and "fujitsu" models. Definitions using only a
single mux specification also work. Other ALC chips should be fine but I
cannot test these myself. The "auto" modes should also continue to function
but again I have not verified this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver,HDA generic driver
- Fix autoconfig speaker/hp detection
Now it allows multiple speaker pins (e.g. Dell laptops have such config)
- Use speaker or hp pins if no line-outs are available
This fixes the silence output on recent Dell laptops with STAC9200
(ALSA bug#1843)
- Fix analog/realtek/sigmatel autoconfig parser
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,HDA Codec driver
Added a new model 'lg' for LG laptop (m1 express dual) with ALC880 codec.
Also clean up the initialization/unsol_event hooks in patch_realtek.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver,HDA generic driver
Add 'fujitsu' model for ALC262 patch to support a FSC laptop.
The internal speaker is turned on/off with jack sensing.
Also fixed alc262 'basic' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds mixer controls to the 'test' ALC260 model which allow the
user to selectively enable or disable the SPDIF output pins. This should
assist people identify digital outputs on machines which bring them to the
outside world.
Note that while the patch *should* work, I cannot personally verify it since
my laptop doesn't bring the SPDIF lines out.
As for the GPIO switches added in patch 4, these controls are currently
only compiled in if debug mode is selected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch is janitorial - it cleans up a number of cosmetic issues with
the 'fujitsu' and 'test' models. Issues addressed:
* spaces instead of tabs used for some indents,
* clarified/corrected selected comments.
Unlike a patch from earlier this week, this keeps both ADCs connected to
the mic1 pin widget by default. I believe this is the better default, since
some laptops don't bring the line1 widget to the outside world. Most (if
not all) do bring mic1 out though, so it seems to me that this default
should remain in place.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds a new 'acer' model. It is based on work by Rimas and many
other dedicated Acer owners over the past few weeks (see bug number
1618) - kudos to them. This adds support for a variety of Acer laptops,
although we are still in the process of collecting pci/subsystem IDs to add.
There are still some potentially outstanding issues: there are reports that
the CD control might not yet be functional for example. However, the time
is probably right to get a 'first cut' into the kernel which can be refined
as more test reports come in.
From the reports by various Acer owners, this code allows them to record
from internal mics and external jacks. Playback also seems to work to all
external jacks and the internal speaker. The 'beep' control doesn't appear
functional at the moment.
This patch depends on the changes made in patch 3/7.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds 'test' model mixer switches for the GPIO controls found on
the ALC260. It has been found that some laptops (eg: Acer) can use these to
enable particular controls, so it would be useful to have access to these
via the 'test' model. It will make testing new models easy, especially if
certain outputs cannot be made to work any other way.
This patch *should* work, but because the GPIO pins don't do anything in
my laptop I cannot personally verify that all this works as expected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch generalises a structure added for the 'fujitsu' model but which
is potentially useful for other models as well. It turns the
'alc260_fujitsu_adc_nids' array into 'alc260_dual_adc_nids'; for other
models which decide to utilise the dual ADC functionality there's really
no reason why they need to define their own list of ADC nids.
The 'fujitsu' model preset is adjusted accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
