The PCI code in 32 and 64 bits fixes up resources differently.
32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus()
while 64 bits does things in various places depending on whether you
are using OF probing, using PCI hotplug, etc...
This merges those by basically using the 32 bits approach for both,
with various tweaks to make 64 bits work with the new approach.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges the PowerPC 32 and 64 bits version of pcibios_resource_to_bus
and pcibios_bus_to_resource().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds flags the platforms can use to enable domain numbers
in /proc/bus/pci.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code carries an old hack that was only useful for G5
machines. Nowdays, the 32 bits kernel doesn't support any of those
machines anymore so the hack is basically never used, so remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds to the 32 bits PCI code some flags, replacing the old
pci_assign_all_busses global, that allow us to control various
aspects of the PCI probing, such as whether to re-assign all
resources or not, or to not try to assign anything at all.
This also adds the flag x86 already has to avoid ISA alignment
on bridges that don't have ISA forwarding enabled (no legacy
devices on the top level bus) and sets it for PowerMacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PowerPC PCI code has a hack for use by some PowerMacs
to try to re-open PCI<->PCI bridge IO resources that were closed
by the firmware. This is no longer necessary as the generic code
will now do that for us.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the 32 bits PowerPC PCI code use the generic code to assign
resources to devices that had unassigned or conflicting resources.
This allow us to remove the local implementation that was incomplete and
could not assign for example a PCI<->PCI bridge from scratch, which is
needed on various embedded platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a stale & bogus piece of code in 32 bits PCI code that
complains about ISA related alignment issues. Just remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch alters the kernel makefiles to build dtc from the sources
embedded in the previous patch. It also changes the
arch/powerpc/boot/wrapper script to use the embedded dtc, rather than
expecting a copy of dtc already installed on the system.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc into the kernel source, in
arch/powerpc/boot/dtc-src. This commit only imports the upstream
sources verbatim, a later commit will actually link it into the kernel
Makefiles and use the embedded code during the kernel build.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's nothing in holly.c that needs linux/ide.h, just remove it from
the list of includes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerPC currently doesn't implement pci_set_dma_mask(), which means drivers
calling it will get the generic version in drivers/pci/pci.c.
The powerpc dma mapping ops include a dma_set_mask() hook, which luckily is
not implemented by anyone - so there is no bug in the fact that the hook
is currently never called.
However in future we'll add implementation(s) of dma_set_mask(), and so we
need pci_set_dma_mask() to call the hook.
To save adding a hook to the dma mapping ops, pci-set_consistent_dma_mask()
simply calls the dma_set_mask() hook and then copies the new mask into
dev.coherenet_dma_mask.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have multiple calls to has_feature being inlined, but gcc can't
be sure that the store via get_paca() doesn't alias the path to
cur_cpu_spec->feature.
Reorder to put the calls to read_purr and read_spurr adjacent to each
other. To add a sense of consistency, reorder the remaining lines to
perform parallel steps on purr and scaled purr of each line instead of
calculating and then using one value before going on to the next.
In addition, we can tell gcc that no SPURR means no PURR. The test is
completely hidden in the PURR case, and in the !PURR case the second test
is eliminated resulting in the simple register copy in the out-of-line
branch.
Further, gcc sees get_paca()->system_time referenced several times and
allocates a register to address it (shadowing r13) instead of caching its
value. Reading into a local varable saves the shadow of r13 and removes
a potentially duplicate load (between the nested if and its parent).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If CPU_FTR_PURR is not set, we will never set cpu_purr_data->initialized.
Checking via __get_cpu_var on 64 bit avoids one dependent load compared
to cpu_has_feature in the not-present case, and is always required when
it is present. The code is under CONFIG_VIRT_CPU_ACCOUNTING so 32 bit
will not be affected.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
timer_interrupt() was calculating per_cpu_offset several times, having to
start from the toc because of potential aliasing issues.
Placing both decrementer per_cpu varables in a struct and calculating
the address once with __get_cpu_var results in better code on both 32
and 64 bit.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use __get_cpu_var(x) instead of per_cpu(x, smp_processor_id()), as it
is optimized on ppc64 to access the current cpu's per-cpu offset directly;
it's local_paca.offset instead of TOC->paca[local_paca->processor_id].offset.
This is the trivial portion, two functions with one use each.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
as its only called from time_init, which is __init.
Also remove unneeded forward declaration.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The per-processor interrupt request register and current processor
priority register are only accessed on the current cpu. In fact the
hypervisor doesn't even let us choose which cpu's registers to access.
The only function to use cpu twice is xics_migrate_irqs_away, not a fast
path. But we can cache the result of get_hard_processor_id() instead of
calling get_hard_smp_processor_id(cpu) in a loop across the call to rtas.
Years ago the irq code passed smp_processor_id into get_irq, I thought
we might initialize the CPPR third party at boot as an extra measure of
saftey, and it made the code symmetric with the qirr (queued interrupt
for software generated interrupts), but now it is just extra and
sometimes unneeded work to pass it down.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits the machine definition for celleb into two definitions,
one for celleb_beat, and the other for celleb_native. Though this
looks complex because of sorting some functions, there are no
more semantic changes than that for the splitting.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes mmio_nvram_init() callable unconditionally by providing
a dummy definition when CONFIG_MMIO_NVRAM is not defined.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement MSI support for PA Semi PWRficient platforms. MSI is done
through a special range of sources on the openpic controller, and they're
unfortunately breaking the usual concepts of how sources are programmed:
* The source is calculated as 512 + the value written into the MSI
register
* The vector for this source is added to the source and reported
through IACK
This means that for simplicity, it makes much more sense to just set the
vector to 0 for the source, since that's really the vector we expect to
see from IACK.
Also, the affinity/priority registers will affect 16 sources at a
time. To avoid most (simple) users from being limited by this, allocate
16 sources per device but use only one. This means that there's a total
of 32 sources.
If we get usage scenarions that need more sources, the allocator should
probably be revised to take an alignment argument and size, not just do
natural alignment.
Finally, since I'm already touching the MPIC names on pasemi, rename
the base one from the somewhat odd " PAS-OPIC " to "PASEMI-OPIC".
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit fbd568a3e6 ("Change
synchronize_kernel to _rcu and _sched") changed the deprecated
synchronize_kernel() in HvLpEvent_unregisterHandler() to
synchronize_rcu(). It turns out that it should have been
synchronize_sched().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many operations, as currently used in the wrapper, assume they can
pass NULL and have it be treated as the root node. However, libfdt-wrapper
converts NULL to -1, which is only appropriate when searching for nodes,
and will cause an error otherwise.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
fdt_wrapper_create_node passes a variable called offset to offset_devp(),
which uses said parameter to initialize a local variable called offset.
Due to one of the odder aspects of the C language, the result is an
undefined variable, with no error or warning.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a dumb simple implementation of fake NUMA nodes for PowerPC.
Fake NUMA nodes can be specified using the following command line option
numa=fake=<node range>
node range is of the format <range1>,<range2>,...<rangeN>
Each of the rangeX parameters is passed using memparse(). I find this
useful for fake NUMA emulation on my simple PowerPC machine. I've
tested it on a non-numa box with the following arguments:
numa=fake=1G
numa=fake=1G,2G
name=fake=1G,512M,2G
numa=fake=1500M,2800M mem=3500M
numa=fake=1G mem=512M
numa=fake=1G mem=1G
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Optimize MPIC IPIs, by passing in the IPI number as the argument to the
handler, since all we did was translate it back based on which mpic
the interrupt came though on (and that was always the primary mpic).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
when called by setup_arch) after smp_store_cpu_info() had set it to the
correct value.
The error shows up in 'cat /proc/cpuinfo' will all cpus = 0.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Suresh B Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Adjust CMCI mask on CPU hotplug
[IA64] make flush_tlb_kernel_range() an inline function
[IA64] Guard elfcorehdr_addr with #if CONFIG_PROC_FS
[IA64] Fix Altix BTE error return status
[IA64] Remove assembler warnings on head.S
[IA64] Remove compiler warinings about uninitialized variable in irq_ia64.c
[IA64] set_thread_area fails in IA32 chroot
[IA64] print kernel release in OOPS to make kerneloops.org happy
[IA64] Two trivial spelling fixes
[IA64] Avoid unnecessary TLB flushes when allocating memory
[IA64] ia32 nopage
[IA64] signal: remove redundant code in setup_sigcontext()
IA64: Slim down __clear_bit_unlock
Currently CMCI mask of hot-added CPU is always disabled after CPU hotplug.
We should adjust this mask depending on CMC polling state.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes an unused variable warning in mm/vmalloc.c.
Tony: also fix resulting fallout in uncached.c with a
typo in args to flush_tlb_kernel_range().
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Access to elfcorehdr_addr needs to be guarded by #if CONFIG_PROC_FS
as well as the existing #if guards.
Fixes the following build problem:
arch/ia64/hp/common/built-in.o: In function
`sba_init':arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
:arch/ia64/hp/common/sba_iommu.c:2043: undefined reference to `elfcorehdr_addr'
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Altix shub2 BTE error detail bits are in a different location
than on shub1. The current code does not take this into account
resulting in all shub2 BTE failures mapping to "unknown".
This patch reads the error detail bits from the proper location,
so the correct BTE failure reason is returned for both shub1
and shub2.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following assembler warning messages.
AS arch/ia64/kernel/head.o
arch/ia64/kernel/head.S: Assembler messages:
arch/ia64/kernel/head.S:1179: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1179: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
arch/ia64/kernel/head.S:1180: Warning: Use of 'ld8' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1180: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
:
arch/ia64/kernel/head.S:1213: Warning: Use of 'ldf.fill.nta' violates RAW dependency 'CR[PTA]' (data)
arch/ia64/kernel/head.S:1213: Warning: Only the first path encountering the conflict is reported
arch/ia64/kernel/head.S:1178: Warning: This is the location of the conflicting usage
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following compiler warning messages.
CC arch/ia64/kernel/irq_ia64.o
arch/ia64/kernel/irq_ia64.c: In function 'create_irq':
arch/ia64/kernel/irq_ia64.c:343: warning: 'domain.bits[0u]' may be used uninitialized in this function
arch/ia64/kernel/irq_ia64.c: In function 'assign_irq_vector':
arch/ia64/kernel/irq_ia64.c:203: warning: 'domain.bits[0u]' may be used uninitialized in this function
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I tried to upgrade an IA32 chroot on my IA64 to a new glibc with TLS.
It kept dying because set_thread_area was returning -ESRCH
(bugs.debian.org/451939).
I instrumented arch/ia64/ia32/sys_ia32.c:get_free_idx() and ended up
seeing output like
[pid] idx desc->a desc->b
-----------------------------
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> 0 0
[2710] 2 -> 0 0
[2710] 0 -> c6b0ffff 40dff31b
[2710] 1 -> c6b0ffff 40dff31b
[2710] 2 -> 0 0
[2711] 0 -> c6b0ffff 40dff31b
[2711] 1 -> c6b0ffff 40dff31b
[2711] 2 -> 48c0ffff 40dff317
which suggested to me that TLS pointers were surviving exec() calls,
leading to GDT pointers filling up and the eventual failure of
get_free_idx().
I think the solution is flushing the tls array on exec.
Signed-Off-By: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The ia64 oops message doesn't include the kernel version, which
makes it hard to automatically categorize oops messages scraped
from mailing lists and bug databases.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Improve performance of memory allocations on ia64 by avoiding a global TLB
purge to purge a single page from the file cache. This happens whenever we
evict a page from the buffer cache to make room for some other allocation.
Test case: Run 'find /usr -type f | xargs cat > /dev/null' in the
background to fill the buffer cache, then run something that uses memory,
e.g. 'gmake -j50 install'. Instrumentation showed that the number of
global TLB purges went from a few millions down to about 170 over a 12
hours run of the above.
The performance impact is particularly noticeable under virtualization,
because a virtual TLB is generally both larger and slower to purge than
a physical one.
Signed-off-by: Christophe de Dinechin <ddd@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Convert ia64's ia32 support from nopage to fault.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes some redundant code in the function setup_sigcontext().
The registers ar.ccv,b7,r14,ar.csd,ar.ssd,r2-r3 and r16-r31 are not
restored in restore_sigcontext() when (flags & IA64_SC_FLAG_IN_SYSCALL) is
true. So we don't need to zero those variables in setup_sigcontext().
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We're currently getting a warning from not checking the result of
sysfs_create_group, which is declared as __must_check.
This change introduces appropriate error-handling for
spu_add_sysdev_attr_group()
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, we have a possibilty that the SLBs setup during context
switch don't cover the entirety of the necessary lscsa and code
regions, if these regions cross a segment boundary.
This change checks the start and end of each region, and inserts a SLB
entry for each, if unique. We also remove the assumption that the
spu_save_code and spu_restore_code reside in the same segment, by using
the specific code array for save and restore.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a function spu_64k_pages_available(), so that we can abstract the
explicity use of mmu_psize_defs() in lssca_alloc.c
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that we have a helper function to setup a SPU SLB, use it for
__spu_trap_data_seq.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, the SPU context switch code (spufs/switch.c) sets up the
SPU's SLBs directly, which requires some low-level mm stuff.
This change moves the kernel SLB setup to spu_base.c, by exposing
a function spu_setup_kernel_slbs() to do this setup. This allows us
to remove the low-level mm code from switch.c, making it possible
to later move switch.c to the spufs module.
Also, add a struct spu_slb for the cases where we need to deal with
SLB entries.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch changes the way we check for the existence of
vicinity property in spe device nodes.
The new implementation does not depend on having an initialized
cbe_spu_info[0].spus, and checks for presence of vicinity in all
nodes, not only in the first one.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Export force_sig_info to allow signals to be sent from a modular spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix debug_bus_control and group_control PMU register values set up in
set_pm_event(). Initialize variables before calling set_pm_event().
Delete unused static array and code that initialized it.
Rename constant to better reflect usage.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pm_interval register in the Cell PMU is read/write, but was implemented in
the kernel as write-only. Previously, the written value was saved in a "shadow"
copy so calls to cbe_read_pm() could return the value.
Perfmon2 needs to be able to read the current values of pm_interval, so change
cbe_read_pm() to read the actual register instead of the "shadow" copy. There
is currently no code in the kernel that tries to read the pm_interval register
with cbe_read_pm() (expecting to receive the "shadow" value), so this should
not break any existing code.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
this is the tale of a full day spent debugging an ancient but elusive bug.
after booting up thousands of random .config kernels, i finally happened
to generate a .config that produced the following rare bootup failure
on 32-bit x86:
| ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
| ..MP-BIOS bug: 8254 timer not connected to IO-APIC
| ...trying to set up timer (IRQ0) through the 8259A ... failed.
| ...trying to set up timer as Virtual Wire IRQ... failed.
| ...trying to set up timer as ExtINT IRQ... failed :(.
| Kernel panic - not syncing: IO-APIC + timer doesn't work! Boot with apic=debug
| and send a report. Then try booting with the 'noapic' option
this bug has been reported many times during the years, but it was never
reproduced nor fixed.
the bug that i hit was extremely sensitive to .config details.
First i did a .config-bisection - suspecting some .config detail.
That led to CONFIG_X86_MCE: enabling X86_MCE magically made the bug disappear
and the system would boot up just fine.
Debugging my way through the MCE code ended up identifying two unlikely
candidates: the thing that made a real difference to the hang was that
X86_MCE did two printks:
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
Adding the same printks to a !CONFIG_X86_MCE kernel made the bug go away!
this left timing as the main suspect: i experimented with adding various
udelay()s to the arch/x86/kernel/io_apic_32.c:check_timer() function, and
the race window turned out to be narrower than 30 microseconds (!).
That made debugging especially funny, debugging without having printk
ability before the bug hits is ... interesting ;-)
eventually i started suspecting IRQ activities - those are pretty much the
only thing that happen this early during bootup and have the timescale of
a few dozen microseconds. Also, check_timer() changes the IRQ hardware
in various creative ways, so the main candidate became IRQ0 interaction.
i've added a counter to track timer irqs (on which core they arrived, at
what exact time, etc.) and found that no timer IRQ would arrive after the
bug condition hits - even if we re-enable IRQ0 and re-initialize the i8259A,
but that we'd get a small number of timer irqs right around the time when we
call the check_timer() function.
Eventually i got the following backtrace triggered from debug code in the
timer interrupt:
...trying to set up timer as Virtual Wire IRQ... failed.
...trying to set up timer as ExtINT IRQ...
Pid: 1, comm: swapper Not tainted (2.6.24-rc5 #57)
EIP: 0060:[<c044d57e>] EFLAGS: 00000246 CPU: 0
EIP is at _spin_unlock_irqrestore+0x5/0x1c
EAX: c0634178 EBX: 00000000 ECX: c4947d63 EDX: 00000246
ESI: 00000002 EDI: 00010031 EBP: c04e0f2e ESP: f7c41df4
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: ffe04000 CR3: 00630000 CR4: 000006d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
[<c05f5784>] setup_IO_APIC+0x9c3/0xc5c
the spin_unlock() was called from init_8259A(). Wait ... we have an IRQ0
entry while we are in the middle of setting up the local APIC, the i8259A
and the PIT??
That is certainly not how it's supposed to work! check_timer() was supposed
to be called with irqs turned off - but this eroded away sometime in the
past. This code would still work most of the time because this code runs
very quickly, but just the right timing conditions are present and IRQ0
hits in this small, ~30 usecs window, timer irqs stop and the system does
not boot up. Also, given how early this is during bootup, the hang is
very deterministic - but it would only occur on certain machines (and
certain configs).
The fix was quite simple: disable/restore interrupts properly in this
function. With that in place the test-system now boots up just fine.
(64-bit x86 io_apic_64.c had the same bug.)
Phew! One down, only 1500 other kernel bugs are left ;-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Kprobes for x86-64 may cause a kernel crash if it inserted on "iret"
instruction. "call absolute" is invalid on x86-64, so we don't need
treat it.
- Change the processing order as same as x86-32.
- Add "iret"(0xcf) case.
- Remove next_rip local variable.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
jprobe for x86-64 may cause kernel page fault when the jprobe_return()
is called from incorrect function.
- Use jprobe_saved_regs instead getting it from stack.
(Especially on x86-64, it may get incorrect data, because
pt_regs can not be get by using container_of(rsp))
- Change the type of stack pointer to unsigned long *.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch is for controlling the upper 32bits of the event ctrl msrs.
This includes the upper 4 bits of the event select and the Guest Only and
Host Only bits
This patch is necessary to make Event Based Profiling work reliably on a
Family 10h processor
[akpm@linux-foundation.org: checkpatch.pl fixes]
Signed-off-by: Barry Kasindorf <barry.kasindorf@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This fixes some of the alpha-specific build problems, except a) modpost
warning about COMMON symbol "saved_config" and b) nasty final link
failure with gcc-4.x, -Os and scsi-disk driver configured built-in
(due to jump table in .rodata referencing discarded .exit.text).
- build failure with gcc-4.2.x: fix up casts in cia_io* routines to avoid
warnings ('discards qualifiers from pointer target type'), which are
failures, thanks to -Werror;
- modpost warnings: add missing __init qualifier for titan and marvel;
for non-generic build, move machine vectors from .data to .data.init.refok
section;
- unbreak CPU-specific optimization: rearrange cpuflags-y assignments
so that extended -mcpu value (ev56, pca56, ev67) overrides basic
one (ev5, ev6) and not vice versa.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First of all, thanks to Bob Tracy <rct@frus.com> and
Michael Cree <mcree@orcon.net.nz> for testing.
Especially to Bob, as he has done titanic multi-day git-bisect
work that finally helped to reproduce and nail down the bug
(http://bugzilla.kernel.org/show_bug.cgi?id=9457).
[ev6-]stxncpy.S: it's t12, not t2 register that is supposed to contain
the last byte offset upon return. As a result of wrong register use
(which was my fault back in 2003, IIRC), under some circumstances extra
terminating zero bytes were added to destination string. This particularly
led to incorrect DEVPATH strings generated in uevent and therefore to udev
problems.
strncpy.S: unrelated bug I found while testing the above fix - destination
is not properly zero-padded then a byte count exceeds source length.
Actually this is addition to strncpy fix from last year.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Bob Tracy <rct@frus.com>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes when UML is debugged gdb miss breakpoints.
When process traced by gdb do fork, debugger remove breakpoints from
child address space. There is possibility to trace more than one fork,
but this not work with UML, I guess (only guess) there is a deadlock -
gdb waits for UML and UML waits for gdb.
When clone() is called with SIGCHLD and CLONE_VM flags, gdb see this
as PTRACE_EVENT_FORK not as PTRACE_EVENT_CLONE and remove breakpoints
from child and at the same time from traced process, because either
have the same address space.
Maybe it is possible to do fix in gdb, but I'm not sure if there is
easy way to find out if traced and child processes share memory. So I
do fix for UML, it simply do not call clone() with both SIGCHLD and
CLONE_VM flags together. Additionally __WALL flag is used for
waitpid() to assure not miss clone and normal process events.
[ jdike - checkpatch fixes ]
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit efa4d2fb04 ("Hibernation:
Use temporary page tables for kernel text mapping on x86_64") because it
causes my t61p to reboot right at the end of resume-from-disk. For
reasons unknown at this time.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <ak@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add proper support for CLOCK_EVT_MODE_RESUME and in the process fix
CLOCK_EVT_MODE_SHUTDOWN so that only the enable bits are toggled for both.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to ARM7TDMI Technical Reference Manual (ARM DDI 0210C) writing
to the DCC data write register coproc dest registers are 1 and 0, not 0
and 1.
ARM920T TRM (ARM DDI 0151C) agrees on that.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Make PS3_SYS_MANAGER default y, not m
[POWERPC] Fix rounding bug in emulation for double float operating
[POWERPC] iSeries: don't printk with HV spinlock held
[POWERPC] 82xx: mpc8272ads, pq2fads: Update defconfig with CONFIG_FS_ENET_MDIO_FCC
[POWRPC] CPM2: Eliminate section mismatch warning in cpm2_reset().
[POWERPC] Kill non-existent symbols from ksyms and commproc.h
[POWERPC] Fix typo #ifdef -> #ifndef
Frank Rowand <frank.rowand@am.sony.com> reports:
> In linux-2.6.24-rc4 the Toshiba RBTX4927 hangs on boot.
>
> The cause is that plat_time_init() from arch/mips/tx4927/common/
> tx4927_setup.c does not override the __weak plat_time_init() from
> arch/mips/kernel/time.c. This is due to a compiler bug in gcc 4.1.1. The
> bug is reported to not exist in earlier versions of gcc, and to be fixed in
> 4.1.2. The problem is that the __weak plat_time_init() is empty and thus
> gets optimized out of existence (thus the linker is never given the option
> to replace the __weak function).
[ He meant the call to plat_time_init() from time_init() gets optimized away ]
> For more info on the gcc bug see
>
> http://gcc.gnu.org/bugzilla/show_bug.cgi?id=27781
>
> The attached patch is one workaround. Another possible workaround
[ His patch adds -fno-unit-at-a-time for time.c ]
> would be to change the __weak plat_time_init() to be a non-empty
> function.
The __weak definition of plat_time_init was only ever meant to be a
migration helper to keep platforms that don't have a plat_time_init
compiling. A few greps says that all platforms now supply their own
plat_time_init() so the weak definition is no longer needed. So I
instead delete it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There might be other reasons why a resource might be marked as fixed
such as a PCI UART holding the system console but until we use
IORESOURCE_PCI_FIXED that way also this will work.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the PCI specific code in this function doesn't check for the address range
being under the upper bound of the PCI memory window correctly -- fix this,
somewhat beautifying the code around the check, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
... by getting the PCI resources back into the 32-bit range -- there's no
need therefore for CONFIG_RESOURCES_64BIT either. This makes Alchemy PCI
work again while currently the kernel skips the bus scan.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Updates the ucc_geth device driver to check the new rx-clock-name and
tx-clock-name properties first. If present, it uses the new function
qe_clock_source() to obtain the clock source. Otherwise, it checks the
deprecated rx-clock and tx-clock properties.
Update the device trees for 832x, 836x, and 8568 to contain the new property
names only.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it's impossible to build a ps3_defconfig which will reboot
without modules installed. This makes it all too easy to find yourself
with a PS3 that won't reboot.
This is because the system manager driver, which provides the reboot
mechanism, is only selectable if PS3_ADVANCED is set, else it defaults
to m. In ps3_defconfig PS3_ADVANCED is not set, therefore the system
manager is built as a module.
It would be desirable IMHO for the defconfig to produce a kernel that
boots and reboots, without needing modules to be installed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add function qe_clock_source() which takes a string containing the name of a
QE clock source (as is typically found in device trees) and returns the
matching enum qe_clock value.
Update booting-without-of.txt to indicate that the UCC properties rx-clock
and tx-clock are deprecated and replaced with rx-clock-name and tx-clock-name,
which use strings instead of numbers to indicate QE clock sources.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes rounding bug in emulation for double float operating on PowerPC platform.
When pack double float operand, it need to truncate the tail due to the limited precision.
If the truncated part is not zero, the last bit of work bit (totally 3 bits) need to '|' 1.
This patch is completed in _FP_FRAC_SRS_2(X,N,sz) (arch/powerpc/math-emu/op-2.h).
Originally the code leftwards rotates the operand to just keep the truncated part,
then check whether it is zero. However, the number it rotates is not correct when
N is not smaller than _FP_W_TYPE_SIZE, and it will cause the work bit '|' 1 in the improper case.
This patch fixes this issue.
Signed-off-by: Liu Yu <b13201@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Printk was observed to hang during module unload due to a limited
window of characters that may be sent to the hypervisor. The window
only reexpands when we receive an ack from the HV and the spinlock here
prevents us from ever processing that ack. This fixes it by dropping
the lock before doing the printk, then looping back to the top to
reacquire the lock.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the CPM command handling into commproc.c
for CPM1 and cpm2_common.c. This is yet another preparation
to get rid of drivers accessing the CPM via the global cpmp.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
PORTA and PORTB have odr registers, as well. However, the PORTB odr
register is only 16bit.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Verified on mpc866ads. This version has muram and brg nodes added to dts
to get the things work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
This was recently made configurable, and needs to be set for these boards.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove exports of __res and cpm_install_handler/cpm_free_handler. Remove
cpm_install_handler/cpm_free_handler from the commproc.h as well. Both
were used for ARCH=ppc and aren't defined for ARCH=powerpc.
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:180: error: '__res' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:180: warning: type defaults to 'int' in declaration of '__res'
make[1]: *** [arch/powerpc/kernel/ppc_ksyms.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
LD .tmp_vmlinux1
arch/powerpc/kernel/built-in.o:(__ksymtab+0x198): undefined reference to `cpm_free_handler'
arch/powerpc/kernel/built-in.o:(__ksymtab+0x1a0): undefined reference to `cpm_install_handler'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This was caught and identified by Greg Onufer.
Since we setup the 256M/4M bitmap table after taking over the trap
table, it's possible for some 4M mapping to get loaded in the TLB
beforhand which later will be 256M mappings.
This can cause illegal TLB multiple-match conditions. Fix this by
setting up the bitmap before we take over the trap table.
Next, __flush_tlb_all() was not doing anything on hypervisor
platforms. Fix by adding sun4v_mmu_demap_all() and calling it.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to mask out the proper bits when testing the dispatch status
register else we can see unrelated NACK bits from previous cross call
sends.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only external interrupts in edge detect mode support ack operation.
Therefore, in most cases ack is not needed. The patch makes ipic
ack only when it's needed. This could boost over all system performance.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added aliases nodes for kurobox, 83xx, 85xx, and 86xx platforms.
This included added labels and cell-index properties for serial and
pci nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Removed address fields in ethernet nodes
* Removed #address-cells, #size-cells from gianfar nodes
* Added cell-index to gianfar and ucc ethernet nodes
* Added enet[0..3] labels
* Renamed compatible node for gianfar mdio to "fsl,gianfar-mdio"
* Removed device_type = "mdio"
The matching for gianfar mdio still supports the old "mdio"/"gianfar" combo
but it is now considered deprecated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The addition of the aliases node is needed for U-Boot
and, eventually, cuImage, to help locate the proper
nodes reliably when using the libfdt approach.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
qe_setbrg() currently takes an integer to indicate the BRG number. Change that
to take an enum qe_clock instead, since this enum is intended to represent
clock sources.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC837x MDS is a new member of Freescale MDS reference system.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These interrupts are introduced by the latest Freescale SoC
such as MPC837x.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
isel (Integer Select) is a new user space instruction in the
PowerISA 2.04 spec. Not all processors implement it so lets emulate
to ensure code built with isel will run everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the early debug option force the console loglevel
to the max. The early debug option is meant to catch messages very
early in the kernel boot process, in many cases, before the kernel
has a chance to parse the "debug" command line argument. Thus it
makes sense when CONFIG_PPC_EARLY_DEBUG is set, to force the console
log level to the max at boot time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a variant of of_translate_address that uses the dma-ranges
property instead of "ranges", it's to be used by PCI code in parsing
the dma-ranges property.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes "volatile" from the MMIO pointer udbg_comport
in udbg_16550.c driver, it's useless and makes checkpatch.pl
complain when adding things to this file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code will display a rather scary error message
PCI: Cannot allocate resource region N of device XXX
at boot when the existing setup of a device as left by the
firmware doesn't match the kernel needs and the device needs
to be moved. This is often not an error at all, as the kernel
will generally easily reallocate the device elsewhere.
This changes the message to something less scary and lowers
its level from error to warning.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit powerpc resource fixup code uses unsigned longs to do the
offsetting of resources which overflows on platforms such as 4xx where
resources can be 64 bits.
This fixes it by using resource_size_t instead.
However, the IO stuff does rely on some 32 bits arithmetic, so we hack
by cropping the result of the fixups for IO resources with a 32 bits
mask.
This isn't the prettiest but should work for now until we change the
32 bits PCI code to do IO mappings like 64 bits does, within a reserved
are of the kernel address space.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges the 32-bit and 64-bit implementations of
pci_process_bridge_OF_ranges(). The new function is cleaner than both
the old ones, and supports 64 bits ranges on ppc32 which is necessary
for the 4xx port.
It also adds some better (hopefully) output to the kernel log which
should help diagnose problems and makes better use of existing OF
parsing helpers (avoiding a few bugs of both implementations along
the way).
There are still a few unfortunate ifdef's but there is no way around
these for now at least not until some other bits of the PCI code are
made common.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This defines isa_mem_base on both 32 and 64 bits (it used to be 32 bits
only). This avoids a few ifdef's in later patches and potentially can
allow support for VGA text mode on 64 bits powerpc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some versions of Xen 3.x set their magic number to "xen-3.[12]", so
relax the test to match them.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that earlier patches have switched the bootwrapper to using libfdt
for device tree manipulation, this patch removes the now unused
flatdevtree.c and related files.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates libfdt (from the source embedded in an earlier
commit) into the wrapper.a library used by the bootwrapper. This
includes adding a libfdt_env.h file, which the libfdt sources need in
order to integrate into the bootwrapper environment, and a
libfdt-wrapper.c which provides glue to connect the bootwrapper's
abstract device tree callbacks to the libfdt functions.
In addition, this changes the various wrapper and platform files to
use libfdt functions instead of the older flatdevtree.c library.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc libfdt into the kernel source, in
arch/powerpc/boot/libfdt. This only imports the upstream sources
verbatim, later patches are needed to actually link it into the kernel
Makefiles.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There was only one global function in vpdinfo.c and it was only called
from pci.c, so merge them and make the function static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we hardwire the number of SLBs to 64, but PAPR says we
should use the ibm,slb-size property to obtain the number of SLB
entries. This uses this property instead of assuming 64. If no
property is found, we assume 64 entries as before.
This soft patches the SLB handler, so it shouldn't change performance
at all.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and it becomes clear that we should use zalloc_maybe_bootmem.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also remove another unnecessary forward declaration.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It only needs the iommu_table address. It also makes use of the node
name to print error messages. So just pass it the things it needs.
This reduces the places that know about the pci_dn by one.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'data' member of proc_ppc64_lparcfg is unused, but the lparcfg
module's init routine allocates 4K for it.
Remove the code which allocates and frees this buffer.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for native CBE on Celleb, that is, without the BEAT
hypervisor. Many codes in platforms/cell/ are used in native CBE
environment.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following link error with CONFIG_PPC_CELL_NATIVE=y and
CONFIG_PPC_CELL_BLADE=n:
arch/powerpc/platforms/built-in.o: In function `.cell_setup_arch':
setup.c:(.init.text+0xe80): undefined reference to `.mmio_nvram_init'
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also use of_unregister_driver to implement of_unregister_platform_driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerMac and CHRP/BriQ platforms have quirks to switch some IDE
controllers from legacy mode to fully native mode. Those quirks
however will not work properly anymore due to a change to the
generic code to better handle legacy IDE resources.
This fixes it by moving those quirk to "early" quirks (so they
run before resources are probed for the devices) and clearing
all BARs after the conversion to force a reallocation of sane
values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most Malta use an FPGA CPU card which rarely is good for more than 40MHz.
So the performance penalta of the regular timer interrupt, especially
for the VSMP kernel model is significant, even at a mere 100Hz.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IP7 will be enabled automatically in mips_clockevent_init(), if available.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change printk to dev_dbg in ITE 8152 driver and remove printk in ITE 8152 ISR.
Move PCI intialization from ->scan to ->preinit method
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If "CPEI Processor Override" bit is not set in "Platform Interrupt
Source Flags" in "Platform Interrupt Sources Structure" in ACPI MADT,
the target processor of CPEI is restricted to a specific CPU. Because
of this, the delivery mode for CPEI should be IOSAPIC_FIXED.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Restore regs->ccr_iip before kreturn probe handler runs. In this way, if
probe handler does unwind, unwind can correctly get the stack trace.
Fixes: http://sourceware.org/bugzilla/show_bug.cgi?id=5051
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
'!' has a higher priority than '&', so as was
this won't test the first bit, but rather evaluates to false for any non-zero
lsapic->lapic_flags.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Macro efi_md_size is defined in efi.c, and here we apply it throughout
efi.c.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Rename _bss to __bss_start as on other architectures. That makes it
possible to use the <linux/sections.h> instead of own declarations. Also
add __bss_stop because that symbol exists on other architectures.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When initializing pci_controller->node to point to the closest node we need
to take into consideration that a PIC PCI Bridge ASIC can be connected to a
headless/memless node just like the TIOCP and TIOCE Bridge ASICs
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Make some IOSAPIC functions static and remove one that is unused.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not all the return value of __copy_from_user and
__put_user is checked.This patch fixed it.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
With the unionfs patch applied I get
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined!
the other architectures (some, at least) export copy_page() so I guess ia64
should also do so.
To do this we need to move the copy_page() functions out of lib.a and into
built-in.o and add the EXPORT_SYMBOL().
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Don't assume that this file has execute permissions. For example, patch(1)
loses that information.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
/opt/crosstool/gcc-3.4.5-glibc-2.3.6/ia64-unknown-linux-gnu/lib/gcc/ia64-unknown-linux-gnu/3.4.5/../../../../ia64-unknown-linux-gnu/bin/ld: section .data.patch [a000000000000500 -> a000000000000507] overlaps section .dynamic [a0000000000003c8 -> a000000000000507]
This only appears to be a problem with strangely configured
cross-compilation ... native compilers don't have this issue.
But in the interests of helping others at least compile for
ia64, this can go in. -Tony
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] Fix wrong pt_regs in critical exception handler
[AVR32] Fix copy_to_user_page() breakage
[AVR32] Follow the rules when dealing with the OCD system
[AVR32] Clean up OCD register usage
[AVR32] Implement irqflags trace and lockdep support
[AVR32] Implement stacktrace support
[AVR32] Kconfig: Use def_bool instead of bool + default
[AVR32] Fix invalid status register bit definitions in asm/ptrace.h
[AVR32] Add TIF_RESTORE_SIGMASK to the work masks
It's not like it really matters at this point since the system is
dying anyway, but handle_critical pushes too few registers on the
stack so the register dump, which makes the register dump look a bit
strange. This patch fixes it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current implementation of copy_to_user_page() gives "vaddr" to the
cache instruction when trying to sync the icache with the dcache. If
vaddr does not exist in the TLB, the CPU will silently abort the
operation, which may result in the caches staying out of sync.
To fix this, pass the "dst" parameter to flush_icache_range() instead
-- we know this is valid because we just wrote to it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current debug trap handling code does a number of things that are
illegal according to the AVR32 Architecture manual. Most importantly,
it may try to schedule from Debug Mode, thus clearing the D bit, which
can lead to "undefined behaviour".
It seems like this works in most cases, but several people have
observed somewhat unstable behaviour when debugging programs,
including soft lockups. So there's definitely something which is not
right with the existing code.
The new code will never schedule from Debug mode, it will always exit
Debug mode with a "retd" instruction, and if something not running in
Debug mode needs to do something debug-related (like doing a single
step), it will enter debug mode through a "breakpoint" instruction.
The monitor code will then return directly to user space, bypassing
its own saved registers if necessary (since we don't actually care
about the trapped context, only the one that came before.)
This adds three instructions to the common exception handling code,
including one branch. It does not touch super-hot paths like the TLB
miss handler.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Generate a new set of OCD register definitions in asm/ocd.h and rename
__mfdr() and __mtdr() to ocd_read() and ocd_write() respectively.
The bitfield definitions are a lot more complete now, and they are
entirely based on bit numbers, not masks. This is because OCD
registers are frequently accessed from assembly code, where bit
numbers are a lot more useful (can be fed directly to sbr, bfins,
etc.)
Bitfields that consist of more than one bit have two definitions:
_START, which indicates the number of the first bit, and _SIZE, which
indicates the number of bits. These directly correspond to the
parameters taken by the bfextu, bfexts and bfins instructions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The 'H' bit is bit 29, while the 'R' bit doesn't exist. Luckily, we
don't actually use any of the bits in question.
Also update show_regs() to show the Debug Mask and Debug state bits.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
get_cpu() always returns zero on non-SMP builds, but we
really want the physical cpu number in this code in order
to do the right thing.
Based upon a non-SMP kernel boot failure report from Bernd Zeimetz.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ml300 and ml403 xparameters.h files use different macros for the
AC97 interrupt pin assignments. This normalizes them to a canonical
value similar to what EDK generates for most other devices. This is
needed to get ml300 support to compile in arch/ppc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Old debugging hack sneaked back during x86 merge, this removes it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] lba_pci: pci_claim_resources disabled expansion roms
[PARISC] print more than one character at a time for pdc console
[PARISC] Update parisc-linux MAINTAINERS entries
[PARISC] timer interrupt should not be IRQ_DISABLED
Revert "[PARISC] import necessary bits of libgcc.a"
The size of swapper_pg_dir is 8k instead of 4k when using 64-bit PTEs
(CONFIG_PTE_64BIT).
This was reported by Cedric Hombourger <chombourger@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Oprofile: Fix computation of number of counters.
[MIPS] Alchemy: fix IRQ bases
[MIPS] Alchemy: replace ffs() with __ffs()
[MIPS] BCM1480: Fix interrupt routing, take 2.
Make the Kconfig.instrumentation file a bit easier on the eyes, and use
the new ARCH_SUPPORTS_OPROFILE for x86[-64].
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cleanup 09cadedbdc broke the oprofile
configuration for MIPS by allowing oprofile support to be built for
kernel models where oprofile doesn't have a chance in hell to work.
Just a dependecy list on a number of architectures is - surprise - broken
and should as per past discussions probably in most considered to be
broken in most cases. So I introduce a dependency for the oprofile
configuration on ARCH_SUPPORTS_OPROFILE.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's really no reason not to print more than one character at a
time to the PDC console... Booting is measurably speedier, and now I don't
have to watch individual characters get drawn.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The timer interrupt had accidentally been marked IRQ_DISABLED since
IRQ_PER_CPU had been OR-ed in, instead of set. This had been working
by accident for quite a while.
Commit c642b8391c changed the behaviour of
IRQ_PER_CPU interrupts, which previously weren't checked for IRQ_DISABLED.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This reverts commit efb80e7e09, it turned
out to cause sporadic problems with the timer interrupt on 32-bit kernels.
Needs more investigation.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
