* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (27 commits)
omap4: Fix ULPI PHY init for ES1.0 SDP
omap3: beaglexm: fix power on of DVI
omap3: igep3: Add omap_reserve functionality
omap3: beaglexm: fix DVI reset GPIO
omap3: beaglexm: fix EHCI power up GPIO dir
omap3: igep2: Add keypad support
omap3: igep3: Fix IGEP module second MMC channel power supply
omap3: igep3: Add USB EHCI support for IGEP module
omap3: clocks: Fix build error 'CK_3430ES2' undeclared here
arm: omap4: pandaboard: turn on PHY reference clock at init
omap2plus: prm: Trvial build break fix for undefined reference to 'omap2_prm_read_mod_reg'
omap2plus: voltage: Trivial linking fix for 'EINVAL' undeclared
omap2plus: voltage: Trivial linking fix 'undefined reference'
omap2plus: voltage: Trivial warning fix 'no return statement'
omap2plus: clockdomain: Trivial fix for build break because of clktrctrl_mask
arm: omap: gpio: don't access irq_desc array directly
omap2+: pm_bus: make functions used as pointers as static
OMAP: GPIO: fix _set_gpio_triggering() for OMAP2+
OMAP2+: TWL: include pm header for init protos
OMAP2+: TWL: make conversion routines static
...
Fix up conflicts in arch/arm/mach-omap2/board-omap3beagle.c ("DVI reset
GPIO" vs "use generic DPI panel driver")
TFP410 DVI chip is used to provide display out.
This chip is controlled by 2 lines:
LDO which supplies the power is controlled over gpio + 2
and the enable of the chip itself is done over gpio + 1
NOTE: the LDO is necessary for LED, serial blocks as well.
gpio + 1 was used to sense USB overcurrent in vanilla beagle.
Without this fix, the display would not function as the LDO
remains shut down.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO reset line for Beagle XM is different from vanilla beagle
so we populate it as part of gpio update routine.
This in part fixes the issue of display not functioning on beagle XM
platform.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI enable power pin is inverted (active high) in comparison
to vanilla beagle which is active low. Handle this case conditionally.
Without this fix, Beagle XM 4 port EHCI will not function and no
networking will be available
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Still keep sharp_ls_panel, since the sharp_ls_panel driver contains blacklight
control driver code which will be moved out later. Then we can use generic DPI
driver for sharp_ls_panel.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Split omap2_init_common_hw() into two functions. The first,
omap2_init_common_infrastructure(), initializes the hwmod code and
data, the OMAP PM code, and the clock code and data. The second,
omap2_init_common_devices(), handles any other early device
initialization that, for whatever reason, has not been or cannot be
moved to initcalls or early platform devices.
This patch is required for the hwmod postsetup patch, which allows
board files to change the state that hwmods should be placed into at
the conclusion of the hwmod _setup() function. For example, for a
board whose creators wish to ensure watchdog coverage across the
entire kernel boot process, code to change the watchdog's postsetup
state will be added in the board-*.c file between the
omap2_init_common_infrastructure() and omap2_init_common_devices() function
calls.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_MUX is not enabled, we can define board_mux in the header
file instead of forcing every single board to define it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated for combined board-zoom files]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
BugLink: https://bugs.launchpad.net/bugs/608279
Signed-off-by: Mathieu Poirier <mathieu.poirier@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3630 based BeagleBoard xM uses a MicroSD card slot with
no write protection.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
system_rev comes from u-boot and is a constant 0x20, so
Bx boards also fall in this 'if' and will get setup with the
wrong gpio_wp pin. Switch to using the Beagle revision routine
to correcly set pin 23 only for C1/2/3 and C4 Boards. Bx boards
will then use the correct default pin setting.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to the omap3530 ES3.0 Silicon being used on both the
B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
routines to differentiate the Beagle Boards.
However gpio pins 171,172,173 where setup for this prupose, so
lets use them.
Changes:
for older U-Boot's, use omap_mux_init_gpio()
keep Beagle Rev in board-omap3beagle.c
gpio_free on gpio request failure
Tested on Beagle Revisions: B5, C2, C4, and xMA
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most OMAP3-based boards use exactly the same code for .map_io method in
the machine_desc structure.
This patch introduces omap3_map_io and updates board-* files to use it
as .map_io method.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only difference between them is the physical address of the
uart4 port, which is only present in 36xx chips.
We don't really need to care about keeping these 2 functions, since
the decision to use uart4 is more cleanly done later when we do have
access to omap_revision variable.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: added comment for the uart4_phys]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Board file modified for not to provide gpmc phys_base address to nand driver.
The gpmc_nand_init funciton is now used to detect the nand and required to
adopt _prob function as in nand/omap2.c
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds DSS2 support to the beagleboard boardfile. DVI and
TV-out are supported.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
the early_param() call in board-omap3touchbook.c expands to:
static const char __setup_str_early_touchbook_revision[]
__section(.init.rodata) _aligned(1) = tbr;
[...]
and we have a non-const variable being added to the
same section:
static struct ehci_hcd_omap_platform_data ehci_pdata
__section(.init.rodata);
because of that, gcc generates a section type conflict
which can (and actually should) be avoided by marking
const every variable marked with __initconst.
This patch fixes that for the ehci_hdc_omap_platform_data.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for EHCI driver.
Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com>
and Anand Gadiyar <gadiyar@ti.com>.
Overo support added by Olof Johansson <olof@lixom.net>
Beagle support added by Koen Kooi <koen@beagleboard.org>
CM-T32 support added by Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
audio_mclk value is going to be handled by the
twl4030-codec MFD driver, configure the correct
value for boards, which is using the twl4030 audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add needed platform data for the twl4030_codec MFD on boards,
where the audio part of the twl4030 codec is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The host port power is enabled by driving the nEN_USB_PWR low as stated in
the comment. This fix is originally from Steve Sakoman <steve@sakoman.com>.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the low level debug UART io address as per this series.
The change is essential to have CONFIG_DEBUG_LL working.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier BeagleBoards were using pad AH8 muxed to GPIO29 for MMC write-protect.
However, this signal has been changed to pad AG9 in board revision C2.
Fix this by adding mux configuration for pad AG9, runtime check for board
revisions and set the gpio number and pad muxing accordingly.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialize regulators for Beagle and Overo.
Patch is based on earlier patches posted to linux-omap mailing
list.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards. Original timing data is from the Micron
datasheet PDF downloaded from:
http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12. Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management. GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management. GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator. But on HS devices, it
may not be available for Linux use.
It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12.
This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.
Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.
Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
