1
Commit Graph

11253 Commits

Author SHA1 Message Date
Michael Buesch
9cf7f247bd b43: Add key memory dumping
This adds an option to dump all crypto related memory to
the kernel log.
Obviously, it should not be enabled on productive systems. ;)

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:24:06 -05:00
Michael Buesch
b929ecf796 b43: Suspend MAC while killing the radio
We should suspend the MAC, before we kill the radio. This gives
the MAC a chance to leave any TX/RX state and it avoids races on
the PHY/RADIO registers.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:24:04 -05:00
Bob Copeland
fd6effcaf8 ath5k: correct packet length in tx descriptors
Packet length calculation (which includes frame check sequence)
should take into account whether we add a pad field or not.
Extract the calculation into a helper and use it in both places.

Changes to desc.c
Changes-licensed-under: ISC

Changes to ath5k.h, base.c
Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:24:02 -05:00
Michael Buesch
d10d0e5707 b43: Fix some MAC locking
This fixes some locking w.r.t. the lower MAC (firmware).
It also removes a lot of ancient IRQ-locking that's not needed anymore.
We simply suspend the MAC. That's easier and causes less trouble.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:56 -05:00
Rami Rosen
0e7690f1e9 iwlwifi: iwl-tx.c cleanup (remove unused parameter and unused local variable).
This patch removes unused parameter and unused local variable in
methods in iwl-tx.c:

- Remove a parameter (is_unicast) from iwl_tx_cmd_build_basic().

- Remove an unused variable name unicast from iwl_tx_skb().

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:54 -05:00
Jouni Malinen
be2864cfff ath9k: Fixed RX decryption status reporting
The RX code in ath9k uses sc_keymap to figure out whether a default
key was used. However, the default key entries in sc_keymap were
always set and as such, frames could have been claimed to be decrypted
by hardware when they were not. This can cause problems especially
with TKIP since mac80211 is validating the Michael MIC in the frame
and this will result in MIC failure and potentially TKIP
countermeasures if the frame was not decrypted correctly.

Change key cache slot allocation to mark only the keys that really
have been used in sc_keymap to avoid the issue. The key cache slot
selection routines are now internally avoiding the slots that may be
needed for TKIP group keys.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:53 -05:00
Jouni Malinen
ea61213288 ath9k: Fix key cache slot selection for splitmic
ath_reserve_key_cache_slot() was obviously supposed to return an index
to a free slot, not reserved one. This could have caused problems with
hardware revisions that use splitmic.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:51 -05:00
Sujith
aa33de09a8 ath9k: Protect config() callback with a mutex
This should fix the timeout issues seen when using wpa_supplicant.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:50 -05:00
Christian Lamparter
6110781af0 p54usb: bring first generation devices back to life
This patch fixes a serious regression (introduced by:
"p54: fix memory management")
that affected isl3886+net2280 usb devices operation.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:47 -05:00
Jouni Malinen
6ace2891a1 ath9k: Key cache allocation for AP mode
Enhance allocation of key cache entries to support multiple pairwise
keys to fix AP mode with more than one associated STA.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:46 -05:00
Jouni Malinen
f66000f7a3 ath9k: Fix a NULL pointer dereference in ath_rate_get
It looks like mac80211 may try to send unicast frames to a STA that
does not have a STA entry. We need to make sure that that is caught in
the rate control code before dereferencing STA data.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:44 -05:00
Jay Sternberg
91f39e8eea iwlwifi: indicate txpower is off in sysfs
The patch checks if the radio is disabled before displaying the tx power
level. Previously when the txpower was set off show_tx_power still
returned the prior power level. Now it will indicate the power has been
turned off.

Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:42 -05:00
Zhu Yi
f1bc4ac61f iwlwifi: use GFP_KERNEL to allocate Rx SKB memory
Previously we allocate Rx SKB with GFP_ATOMIC flag. This is because we need
to hold a spinlock to protect the two rx_used and rx_free lists operation
in the rxq.

	spin_lock();
	...
	element = rxq->rx_used.next;
	element->skb = alloc_skb(..., GFP_ATOMIC);
	list_del(element);
	list_add_tail(&element->list, &rxq->rx_free);
	...
	spin_unlock();

After spliting the rx_used delete and rx_free insert into two operations,
we don't require the skb allocation in an atomic context any more (the
function itself is scheduled in a workqueue).

	spin_lock();
	...
	element = rxq->rx_used.next;
	list_del(element);
	...
	spin_unlock();
	...
	element->skb = alloc_skb(..., GFP_KERNEL);
	...
	spin_lock()
	...
	list_add_tail(&element->list, &rxq->rx_free);
	...
	spin_unlock();

This patch should fix the "iwlagn: Can not allocate SKB buffers" warning
we see recently.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:41 -05:00
Wu, Fengguang
4087f6f68c iwlwifi: use meaningful vars in _iwl_poll_bit()
Rename vars in _iwl_poll_bit() to better reflect the truth.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:39 -05:00
Wu Fengguang
febf3370c6 iwlwifi: remove useless goto
The patch removes some useless goto in code cleanup.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:38 -05:00
Wu, Fengguang
95aa194ac4 iwlwifi: use type uint for module param debug
This enables one to change the debug level at bit 31.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:36 -05:00
Wu, Fengguang
c3a739fa35 iwlwifi: update comments on the debug interface
Bring up-to-date some comments on the location of debug files.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:35 -05:00
Wu, Fengguang
5c11ec60ef iwlwifi: add line feed to printk
This adds line feed to printk.

Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:33 -05:00
Winkler, Tomas
34c22cf93d iwlwifi: cleanup iwl-dev.h
The patch removes unused definition and moves code to proper places.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:32 -05:00
Rami Rosen
73ec1cc28e iwlwifi: remove a parameter (dest) from *_fill_beacon_frame() methods.
This patch removes a parameter (dest) from iwl_fill_beacon_frame() (iwl-agn.c)
 and from iwl3945_fill_beacon_frame(). (iwl-3945.c,iwl-3945.h)

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:29 -05:00
Vasanthakumar Thiagarajan
ca8a856056 ath9k: Move rate control alg register/unregister to appropriate place
This patch makes sure the rate control alg is registered/unregistered
only once for this module.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:27 -05:00
Vasanthakumar Thiagarajan
9bf9fca8de ath9k: Synchronize DMA transfer with CPU at right place
This patch does pci_dma_sync_single_for_cpu() before accessing
the header of the frame and queueing the same buffer into h/w.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:26 -05:00
Jouni Malinen
f7a276a625 ath9k: Remove MAC header pad before reporting TX status
Remove the possible MAC header pad before reporting TX status to
mac80211. This pad is hardware specific operation and should not be
exposed outside the driver. This fixes the frame body in monitor
interfaces that could be used to check on TX status for transmitted
frames.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:24 -05:00
Jouni Malinen
da027ca00a ath9k: Fix TX status reporting for retries and MCS index
The count field in struct ieee80211_tx_rate does not include the final
successful attempt, so only report retries here.

Fix the struct ieee80211_tx_rate::idx field when MCS was used. It is
supposed to be the MCS index, not an internal index to the rate
control algorithm table.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:23 -05:00
Herton Ronaldo Krzesinski
d858822733 rtl8187: Fix crash on unload when using SLUB debug
Reported-by: Hin-Tak Leung <htl10@users.sourceforge.net>

After the code was modified to use urb anchors ("rtl8187: Use usb anchor
facilities to manage urbs"), rtl8187 began generating an intermittent GPF
on shutdown when using SLUB with debugging enabled. Furthermore, rebooting
the system with a ping running caused a GPF every time. There are two problems:
(1) incorrect locking in the rtl8187_rx_cb() routine, a pre-existing bug that
apparently had not been triggered before, and (2) duplicate freeing of receive
skbs that was probably introduced with the change to anchors.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:20 -05:00
Christian Lamparter
0a5ec96ad6 p54: remove free_on_tx parameter
This patch simplifies the tx code a bit and will be necessary for
the upcoming stlc45xx<->p54 port.

In detail: we no longer have to tell all back-end drivers directly,
if we want to free a frame right after it was send to the firmware,
or if we do it in the library callback later.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:19 -05:00
Christian Lamparter
69ba3e5d74 p54: more accurate rssi to dBm conversion
This patch replaces the static rssi auto calibration data
with more precise values out of the device's eeprom.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:17 -05:00
Larry Finger
da9f57eade rtl8187: Fix error returns
There are two places in the rtl8187 code where a routine was returning zero
(OK) when it should have been returning an error.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:16 -05:00
Ilpo Järvinen
23827926eb libertas: use roundup instead of opencoding
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:14 -05:00
Christian Lamparter
ee370ceda8 p54: update ACK failure statistic counter in real-time
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:13 -05:00
Christian Lamparter
54fdb040b4 p54: move statistic timer update routine into a workqueue
This patch moves a good chunk of code from the former statistic update
timer routine into a workqueue, which is kindly provided by mac80211.

Also as a nice side-effect we can lay the foundation for other
essential housekeeping features we want to do in the future.
e.g:
 - drain the (clogged) tx_queue.
 - initiate bursts.

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:11 -05:00
Mohamed Abbas
d5e490362f iwlagn: fix agn rate scaling
Rate scaling in agn can be broken because of these two problems
    1- the LQ command could not sent, we try to call LQ command before
       post association will be rejected, this will cause the driver to
       break in rs_tx_status reporting initial rate does not match.
    2- In rs_rate_init we can get a value of 12, rate 60, for
       last_txrate_idx, this rate only valid in SISO/MIMO mode only

Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:10 -05:00
Benoit PAPILLAULT
0fe45b1deb ath5k: fix 802.11 header padding on RX, unpadding on TX
Padding the 802.11 header to a multiple of 4 bytes needs to be done only for
frames with a body. This fixes a bug where 2 bytes were missing in monitor
mode for ACK frames. Inspired by a patch from Jouni Malinen on ath9k.

Ref: http://bugzilla.kernel.org/show_bug.cgi?id=12101 :
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:07 -05:00
Jouni Malinen
baad1d921b ath9k: Report HT rates in RX status
Fix and clean up the RX status reporting by getting rid of code that
used internal rate tables and ratekbps calculation. The correct value
is now reported with MCS index instead of the old mechanism that
defaulted to using the highest legacy rate.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:06 -05:00
Sujith
9d8eed12db ath9k: Do not use association state to update rate table
Now that HT information is made available to the driver through
config() callback, the channel type can be calculated whenever
setting the channel. Update the rate table accordingly with the new
channel type.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:23:02 -05:00
Sujith
094d05dc32 mac80211: Fix HT channel selection
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.

Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-19 15:22:54 -05:00
Anton Vorontsov
221b3d60cb ucc_geth: Remove UGETH_FILTERING dead code
The code appears to be dead: nobody call these functions, plus build
breaks when UGETH_FILTERING is enabled:

ucc_geth.c:1848: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c:1848: warning: its scope is only this definition or declaration, which is probably not what you want
ucc_geth.c: In function 'ugeth_82xx_filtering_get_match_addr_in_hash':
ucc_geth.c:1856: error: dereferencing pointer to incomplete type
ucc_geth.c:1874: error: dereferencing pointer to incomplete type
ucc_geth.c:1877: warning: return from incompatible pointer type
ucc_geth.c: At top level:
ucc_geth.c:1885: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_hash':
ucc_geth.c:1894: error: dereferencing pointer to incomplete type
ucc_geth.c:1909: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1909: warning: assignment from incompatible pointer type
ucc_geth.c:1918: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:1928: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_clear_addr_in_hash':
ucc_geth.c:1947: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1947: warning: assignment from incompatible pointer type
ucc_geth.c:1954: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:2060: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_paddr':
ucc_geth.c:2064: error: dereferencing pointer to incomplete type
ucc_geth.c:2073: error: dereferencing pointer to incomplete type
ucc_geth.c:2075: warning: passing argument 2 of 'hw_add_addr_in_paddr' from incompatible pointer type
make[2]: *** [ucc_geth.o] Error 1

The code is there since the driver was merged, and nobody seem to be
interested in fixing or actually using it. If we ever want the
filtering support, we can always revert the patch and fix it, but so
far it just draws reader's attention.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:50:56 -08:00
Anton Vorontsov
3e73fc9a12 ucc_geth: Fix IO memory (un)mapping code
The driver doesn't check ioremap() return value, and doesn't free the
remapped memory.

This patch fixes it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:50:55 -08:00
Anton Vorontsov
ba574696a3 ucc_geth: Cleanup repetitive ucc_geth_memclean() calls
No need to call ucc_geth_memclean() so many times, just check for
errors in ucc_geth_open(), and call ucc_geth_stop() in case of errors.

The ucc_geth_stop() may be called anytime and will do the right thing.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:50:52 -08:00
Anton Vorontsov
67c2fb8ff0 ucc_geth: Fix IRQ freeing code in ucc_geth_open()
open() routine calls stop() in case of errors, the function will try
to free the requested IRQ. But we don't know if it was actually
requested, so the code might issue bogus free_irq(0, dev) call.

Fix this by rearranging the code so that now request_irq() is the last
call in the open() routine, and move free_irq() into the close().

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:50:50 -08:00
Anton Vorontsov
1762a29ae5 ucc_geth: Fix TX watchdog timeout handling
The timeout handling code is currently broken in several ways:

- It calls stop() (which frees all the memory and IRQ), and then
  calls startup() (which won't re-request IRQ, neither it will
  re-init the Fast UCC structure).
- It calls these routines from the softirq context, which is wrong,
  since stop() calls free_irq() (which might sleep) and startup()
  allocates things with GFP_KERNEL.
- It won't soft-reset the PHY. We need the PHY reset for at least
  MPC8360E-MDS boards with Marvell 88E1111 PHY, the PHY won't recover
  from timeouts w/o the reset.

So the patch fixes these problems by implementing the workqueue for the
timeout handling, and there we fully re-open the device via close() and
open() calls. The close/open paths do the right things, and I can see
that the driver actually survive the timeouts.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:48:55 -08:00
Anton Vorontsov
b3431c6476 ucc_geth: Fix endless loop in stop_{tx,rx} routines
Currently the routines wait for the various bits w/o an assumption that
bits may never get set. When timeouts happen I see that these bits never
get set and so the routines hang the kernel.

With this patch we'll wait the graceful stop for 100 ms, and then will
simply exit. There is nothing* we can do about that, but it's OK since
we'll do full reset later.

* Well, actually, there is also not-graceful variant for the TX stop,
  but specs says that we never should use it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:48:53 -08:00
Jesper Dangaard Brouer
e98def1f71 NIU: Implement discard counters, optimize
Optimize the lightly loaded case, by only synchronizing discards stats
when qlen > 10 indicate potential for drops.

Notice Robert Olsson might disagree with this patch.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:27:41 -08:00
Jesper Dangaard Brouer
d231776fda NIU: Implement discard counters, info/debug statements.
Discard packet counter debug statements that can be turned on
at runtime by users to assist debugging of the driver code.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:27:40 -08:00
Jesper Dangaard Brouer
b8a606b871 NIU: Implement discard counters
Implementing discard counters for the NIU driver turned out to be more
complicated than first assumed.

The discard counters for the NIU neptune chip are only 16-bit (even
though this is a 64-bit chip).  These 16-bit counters can overflow
quickly, especially considering this is a 10Gbit/s ethernet card.

The overflow indication bit is, unfortunatly, not usable as the
counter value does not wrap, but remains at max value 0xFFFF.
Resulting in lost counts until the counter is reset.

The read and reset scheme also poses a problem. Both in theory and in
practice counters can be lost in between reading nr64() and clearing
the counter nw64().  For this reason, the number of counter clearings
nw64() is limited/reduced.  On the fast-path the counters are only
syncronized once it exceeds 0x7FFF.  When read by userspace, its
syncronized fully.

Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:27:40 -08:00
Baruch Siach
5664dd5561 enc28j60: reduce the number of spi transfers in enc28j60_set_bank()
A major source of overhead in the enc28j60 driver is the SPI transfers. Each
SPI transfer entails two kernel thread context switches. One major source of
SPI transfers is the enc28j60_set_bank() functions which runs before every
register access. This patch reduces the number of SPI transfers that
enc28j60_set_bank() performs in two ways:

  1. removes unnecessary bank switch for the registers that are present in all
	 banks

  2. when switching from banks 0 or 3 to banks 1 or 2 (i.e. only one bit
	 changes) enc28j60_set_bank() does only one SPI transfer instead of two

According to my tests these changes reduce the number of SPI transfers in
about 25%.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:27:39 -08:00
Wang Chen
b88a2a22c6 netdevice zd1201: Use after free
| commit 3d29b0c33d
| Author: John W. Linville <linville@tuxdriver.com>
| Date:   Fri Oct 31 14:13:12 2008 -0400
|
|     netdevice zd1201: Convert directly reference of netdev->priv to netdev_priv()
|
|     We have some reasons to kill netdev->priv:
|     1. netdev->priv is equal to netdev_priv().
|     2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
|        netdev_priv() is more flexible than netdev->priv.
|     But we cann't kill netdev->priv, because so many drivers reference to it
|     directly.
|
|     OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
|     and I want to kill netdev->priv later, I decided to convert all the direct
|     reference of netdev->priv first.
|
|     (Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
|     changelog but using dev->ml_priv.  That doesn't seem appropriate
|     to me for this driver, so I've revamped it to use netdev_priv()
|     instead. -- JWL)

This commit changed the allocation of netdev, but didn't change
the free method of it.
This causes "zd" be used after the memory, which is pointed by "zd", being
freed by free_netdev().

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-18 22:27:38 -08:00
Holger Eitzenberger
3b5b35d022 bonding: use port_params in __update_lacpdu_from_port
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:13:53 -08:00
Holger Eitzenberger
3c52065fbb bonding: use port_params in __update_default_selected()
I also removed some of the unneeded braces in the if condition to
improve readability and a little bit of reformatting.

Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:13:27 -08:00
Holger Eitzenberger
ce6a49ad40 bonding: use port_params in __update_selected()
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-17 19:13:07 -08:00