Instead of using "magic" sizes for protocol names, replace them by an
array, and use strlen().
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current logic, each raw decoder needs to add a copy of the exact
same sysfs code. This is both unnecessary and also means that (re)loading
an IR driver after raw decoder modules have been loaded won't work as
expected.
This patch moves that logic into ir-raw-event and adds a single sysfs
file per device.
Reading that file returns something like:
"rc5 [rc6] nec jvc [sony]"
(with enabled protocols in [] brackets)
Writing either "+protocol" or "-protocol" to that file will
enable or disable the according protocol decoder.
An additional benefit is that the disabling of a decoder will be
remembered across module removal/insertion so a previously
disabled decoder won't suddenly be activated again. The default
setting is to enable all decoders.
This is also necessary for the next patch which moves even more decoder
state into the central raw decoding structs.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new driver for the Windows Media Center Edition/eHome
Infrared Remote transceiver devices. Its a port of the current
lirc_mceusb driver to ir-core, and currently lacks transmit support,
but will grow it back soon enough... This driver also differs from
lirc_mceusb in that it borrows heavily from a simplified IR buffer
decode routine found in Jon Smirl's earlier ir-mceusb port.
This driver has been tested on the original first-generation MCE IR
device with the MS vendor ID, as well as a current-generation device
with a Topseed vendor ID. Every receiver supported by lirc_mceusb
should work equally well. Testing was done primarily with RC6 MCE
remotes, but also briefly with a Hauppauge RC5 remote, and all works
as expected.
v2: fix call to ir_raw_event_handle so repeats work as they should.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the RC6 keymap for the Windows Media Center Edition remotes
that come bundled with MCE/eHome Infrared Remote transceivers. Tested
with 3 different variants of the remote, but its possible there are
still some additional keys missing, but its simple enough to add them
in later...
This patch also adds an IR_TYPE_ALL convenience macro to make life
easier for receivers that support all IR protocols.
v2: fix an erroneous comment that referred to imon devices
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than registering all IR protocol decoders as enabled when bringing
up a new device, only enable the IR protocol decoder that matches the
keymap being loaded. Additional decoders can be enabled on the fly by
those that need to, either by twiddling sysfs bits or by using the
ir-keytable util from v4l-utils.
Functional testing done with the mceusb driver, and it behaves as expected,
only the rc6 decoder is enabled, keys are all handled properly, etc.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Fri, May 28, 2010 at 3:59 PM, Jarod Wilson <jarod@redhat.com> wrote:
> The mceusb driver I'm about to submit handles just about any raw IR you
> can throw at it. The ir-core loads up all protocol decoders, starting
> with NEC, then RC5, then RC6. RUN_DECODER() was trying them in the same
> order, and exiting if any of the decoders didn't like the data. The
> default mceusb remote talks RC6(6A). Well, the RC6 decoder never gets a
> chance to run unless you move the RC6 decoder to the front of the list.
>
> What I believe to be correct is to have RUN_DECODER keep trying all of
> the decoders, even when one triggers an error. I don't think the errors
> matter so much as it matters that at least one was successful -- i.e.,
> that _sumrc is > 0. The following works for me w/my mceusb driver and
> the default decoder ordering -- NEC and RC5 still fail, but RC6 still
> gets a crack at it, and successfully does its job.
>
> Signed-off-by: Jarod Wilson <jarod@redhat.com>
>
> ---
> drivers/media/IR/ir-raw-event.c | 7 ++++---
>
> diff --git a/drivers/media/IR/ir-raw-event.c b/drivers/media/IR/ir-raw-event.c
> index ea68a3f..44162db 100644
> --- a/drivers/media/IR/ir-raw-event.c
> +++ b/drivers/media/IR/ir-raw-event.c
> @@ -36,14 +36,15 @@ static DEFINE_SPINLOCK(ir_raw_handler_lock);
> */
> #define RUN_DECODER(ops, ...) ({ \
> struct ir_raw_handler *_ir_raw_handler; \
> - int _sumrc = 0, _rc; \
> + int _sumrc = 0, _rc, _fail; \
> spin_lock(&ir_raw_handler_lock); \
> list_for_each_entry(_ir_raw_handler, &ir_raw_handler_list, list) { \
> if (_ir_raw_handler->ops) { \
> _rc = _ir_raw_handler->ops(__VA_ARGS__); \
> if (_rc < 0) \
> - break; \
> - _sumrc += _rc; \
> + _fail++; \
> + else \
> + _sumrc += _rc; \
Self-NAK. The only place we actually *care* about the retval from a
RUN_DECODER() call is in __ir_input_register(), and currently, its
looking for retval < 0, which is currently never possible. When we're
running the decoders, either they fail and return -EINVAL or they
succeed and return 0, and in the register case, we get either a
negative error (ex: -ENOMEM from rc6) or 0, so with the above, _sumrc
will *always* be 0 in the two cases I'm looking at. The third place
where RUN_DECODER gets called (decoder unregister) doesn't care about
the retval either. New patch below, including updated comments about
the macro.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It makes IR to work again for dm1105 and, possibly, others.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix ir-nec-decoder build: it uses bitrev library code, so
select BITREVERSE in its Kconfig.
ir-nec-decoder.c:(.text+0x1a2517): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2526): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2530): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2539): undefined reference to `byte_rev_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add auto-config support for iMON 2.4G LT RF device, based on
debug output from Giulio Amodeo in Red Hat bugzilla #572288.
Also flips the switch on only setting up the rf associate sysfs
attr only if we think we're looking at an RF device, vs. previously,
setting up the attr for all 0xffdc devices, so its possible (but a bit
unlikely) there's another iMON RF device we'll have to fix up.
Nb: should be applied after "IR/imon: clean up usage of bools", or there
will be a slight contextual mismatch.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a mix of 0/1 and false/true. Pick one convention and stick
with it (I picked false/true).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix ir-nec-decoder build: it uses bitrev library code, so
select BITREVERSE in its Kconfig.
ir-nec-decoder.c:(.text+0x1a2517): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2526): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2530): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2539): undefined reference to `byte_rev_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for one more remote control type for Avermedia
M135A (model RM-K6), shipped with Positivo machines.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for Avermedia M733A. The original version for
linux 2.6.31 was sent to me from Avermedia, original author is unknown.
I ported it to current kernels, expanded and fixed key code handling for
RM-K6 remote control, and added an additional pci id also supported.
[mchehab@redhat.com: make checkpatch.pl happier]
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Tue, May 04, 2010 at 06:06:41PM +0200, Dan Carpenter wrote:
> On Tue, May 04, 2010 at 10:03:18AM -0400, Jarod Wilson wrote:
> > @@ -1205,7 +1204,7 @@ static u32 imon_panel_key_lookup(u64 hw_code)
> > if (imon_panel_key_table[i].hw_code == (code | 0xffee))
> > break;
> >
> > - keycode = imon_panel_key_table[i % IMON_KEY_RELEASE_OFFSET].keycode;
> > + keycode = imon_panel_key_table[i].keycode;
> >
> > return keycode;
> > }
>
> There is still potentially a problem here because if we don't hit the
> break statement, then we're one past the end of the array.
D'oh. Okay, here's v2, should fix that buglet too.
This hack was used when the imon driver was using internal key lookup
routines, but became dead weight when the driver was converted to use
ir-core's key lookup routines. These bits simply didn't get removed,
drop 'em now.
Pointed out by Dan Carpenter.
v2: fix possible attempt to access beyond end of key table array,
also pointed out by Dan.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a missing include linux/delay.h to prevent
build failures[1-5]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If there is an error here we should unlock in the caller (which is
imon_init_intf1()). We can remove this stray unlock.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a typo here. We meant to test "ir" instead of "props". The
"props" variable was tested earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original condition is always false because ! has higher precedence
than == and neither 0 nor 1 is equal to IMON_DISPLAY_TYPE_VGA.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplified from version 1, in that hacks heisted from ati_remote2.c
aren't actually necessary, the real fix for too many repeats was
from setting too long a timer release value (200ms) on repeats in
mce mode -- this patch drops the release timeout to 33ms, matching
the input subsystem default input_dev->rep[REP_PERIOD].
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a follow-up to my prior patch implementing ir-core's
change_protocol functionality in the imon driver, which eliminates
a false warning when change_protocol is called without a specific
protocol selected yet (i.e., still IR_TYPE_UNKNOWN). It also removes
some extraneous blank lines getting spewn into dmesg.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pulse-distance is not a protocol, it is a line coding (used by some protocols,
like NEC). Looking at the uses of IR_TYPE_PD, the real protocol seems to be
NEC in all cases (drivers/media/video/cx88/cx88-input.c is the only user).
So, remove IR_TYPE_PD while it is still easy to do so.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop the imon driver's internal protocol definitions in favor of using
those provided by ir-core. Should make ir-keytable Just Work for
switching protocol on the fly on the imon devices that support both the
native imon remotes and mce remotes.
The imon-no-pad-stabilize pseudo-protocol was dropped as a protocol, and
converted to a separate modprobe option (which it probably should have
been in the first place). On the TODO list is to convert this to an as yet
unwritten protocol-specific options framework.
While the mce remotes obviously map to IR_TYPE_RC6, I've yet to look at
what the actual ir signals from the native imon remotes are, so for the
moment, imon native ir is mapped to IR_TYPE_OTHER. Nailing it down more
accurately is also on the TODO list.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some confusing comments in drivers/media/IR/*
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-keytable.c would alloc a suitably sized keymap table
only to have it resized as it is populated with the initial keymap.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a double initialization of the same spinlock in drivers/media/IR/rc-map.c.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver is not properly initializing u64 constants on 32 bit systems:
drivers/media/IR/imon.c:301: warning: integer constant is too large for ‘long’ type
drivers/media/IR/imon.c:302: warning: integer constant is too large for ‘long’ type
drivers/media/IR/imon.c:304: warning: integer constant is too large for ‘long’ type
drivers/media/IR/imon.c:305: warning: integer constant is too large for ‘long’ type
drivers/media/IR/imon.c:308: warning: integer constant is too large for ‘long’ type
drivers/media/IR/imon.c:309: warning: integer constant is too large for ‘long’ type
drivers/media/IR/imon.c:310: warning: integer constant is too large for ‘long’ type
Fix also a few troubles at error printk handling:
drivers/media/IR/imon.c: In function ‘imon_init_intf0’:
drivers/media/IR/imon.c:1909: warning: ‘ret’ may be used uninitialized in this function
drivers/media/IR/imon.c: In function ‘imon_init_intf1’:
drivers/media/IR/imon.c:1989: warning: ‘ret’ may be used uninitialized in this function
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a Sony12/15/20 decoder to ir-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by checkpatch.pl:
ERROR: open brace '{' following function declarations go on the next line
+static inline bool geq_margin(unsigned d1, unsigned d2, unsigned margin) {
ERROR: open brace '{' following function declarations go on the next line
+static inline bool eq_margin(unsigned d1, unsigned d2, unsigned margin) {
ERROR: open brace '{' following function declarations go on the next line
+static inline bool is_transition(struct ir_raw_event *x, struct ir_raw_event *y) {
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements the agreed upon 1:31 integer encoded pulse/duration
struct for ir-core raw decoders. All decoders have been tested after the
change. Comments are welcome.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new driver for the SoundGraph iMON and Antec Veris IR/display
devices commonly found in many home theater pc cases and as after-market
case additions.
[mchehab@redhat.com: add KERN_CONT on line 2098 to shutup checkpatc.pl]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the keymaps for the hardware decode scancodes imon
devices create for their native imon pad (and mini) remotes,
and the hardware scancodes generated by the imon devices when
used with an rc6 windows media center ed. remote.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon driver I've previously submitted and have been porting to
use ir-core needs to use ir_g_keycode_from_table, as ir_keydown is
not sufficient, due to these things having really oddball hardware
decoders in them. This just moves the function declaration from
ir-core-priv.h over to ir-core.h.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of removing an entry, the logic were doing both a deletion and
a key addition, as shown by the log:
[11517.323314] ir_getkeycode: unknown key for scancode 0x0050
[11517.326529] ir_do_setkeycode: #80: Deleting scan 0x0050
[11517.326529] ir_do_setkeycode: #80: New scan 0x0050 with key 0x0000
[11517.340598] ir_getkeycode: unknown key for scancode 0x0051
[11517.343811] ir_do_setkeycode: #81: Deleting scan 0x0051
[11517.343811] ir_do_setkeycode: #81: New scan 0x0051 with key 0x0000
[11517.357889] ir_getkeycode: unknown key for scancode 0x0052
[11517.361104] ir_do_setkeycode: #82: Deleting scan 0x0052
[11517.361104] ir_do_setkeycode: #82: New scan 0x0052 with key 0x0000
[11517.375453] ir_getkeycode: unknown key for scancode 0x0053
[11517.378474] ir_do_setkeycode: #83: Deleting scan 0x0053
[11517.378474] ir_do_setkeycode: #83: New scan 0x0053 with key 0x0000
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As Adreas pointed, RC6 should use CONFIG_IR_RC6_DECODER_MODULE, instead
of the RC5 config option.
Thanks-to: Andreas Oberitter <obi@linuxtv.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds an RC6 decoder (modes 0 and 6A) to ir-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds NECx support to drivers/media/IR/ir-nec-decoder.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds RC5x support to drivers/media/IR/ir-rc5-decoder.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-raw-event.c:55: warning: ‘wq_load’ defined but not used
drivers/media/IR/ir-raw-event.c:222: warning: ‘init_decoders’ defined but not used
drivers/media/IR/rc-map.c: In function ‘get_rc_map’:
drivers/media/IR/rc-map.c:40: warning: unused variable ‘rc’
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-core.h has the kABI to be used by the bridge drivers, when needing to register
IR protocols and pass IR events. However, the same file also contains IR subsystem
internal calls, meant to be used inside ir-core and between ir-core and the raw
decoders.
Better to move those functions to an internal header, for some reasons:
1) Header will be a little more cleaner;
2) It avoids the need of recompile everything (bridge/hardware drivers, etc),
just because a new decoder were added, or some other internal change were needed;
3) Better organize the ir-core API, splitting the functions that are internal to
IR core and the ancillary drivers (decoders, lirc_dev) from the features that
should be exported to IR subsystem clients.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-raw-event.c is currently written with the assumption
that all "raw" hardware will generate events only on state change (i.e.
when a pulse or space starts).
However, some hardware (like mceusb, probably the most popular IR receiver
out there) only generates duration data (and that data is buffered so using
any kind of timing on the data is futile).
Furthermore, using signed int's to represent pulse/space durations is a
well-known approach when writing ir decoders.
With this patch:
- s64 int's are used to represent pulse/space durations in ns
- a workqueue is used to decode the ir protocols outside of interrupt context
- #defines are added to make decoders clearer
- decoder reset is implemented by passing a zero duration to the kfifo queue
and decoders are updated accordingly
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-sysfs.c: In function ‘store_protocol’:
drivers/media/IR/ir-sysfs.c:93: warning: suggest parentheses around assignment used as truth value
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware decoders have a more limited set of decoders than software ones.
In general, they support just one protocol at a given time, but allow
changing between a few options.
Rename the previous badly named "current_protocol" as just "protocol",
meaning the current protocol(s) accepted by the driver, and
add a "support_protocols" to represent the entire universe of supported
protocols by that specific hardware.
As commented on http://lwn.net/Articles/378884/, the "one file, one value"
rule doesn't fit nor does make much sense for bitmap or enum values. So, the
supported_protocols will enum all supported protocols, and the protocol
will present all active protocols.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices have in-hardware Remote Controller decoder, while others
need a software decoder to get the IR code. As each software decoder
can be enabled/disabled individually, allowing multiple protocol
decoding capability.
On the other hand, hardware decoders have a limited protocol
support, often being able of decoding just one protocol each time.
So, each type needs a different set of capabilities to control the
supported protocol(s).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the remote controller class is anyway being renamed from ir to rc
this would be a good time to also rename the devices from rcrcvX to rcX.
I know we haven't reached any agreement on whether transmission will
eventually be handled by the same device, but this change will at
least make the device name non-receive-specific which will make it
possible in the future (and if a different approach is finally
agreed upon, the device name still works).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some spinlocks are not properly initialized on ir core:
[ 471.714132] BUG: spinlock bad magic on CPU#0, modprobe/1899
[ 471.719838] lock: f92a08ac, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 471.727301] Pid: 1899, comm: modprobe Not tainted 2.6.33 #36
[ 471.733062] Call Trace:
[ 471.735537] [<c1498793>] ? printk+0x1d/0x22
[ 471.739866] [<c12694e3>] spin_bug+0xa3/0xf0
[ 471.744224] [<c126962d>] do_raw_spin_lock+0x7d/0x160
[ 471.749364] [<f92a01ff>] ? ir_rc5_register+0x6f/0xf0 [ir_rc5_decoder]
So, use static initialization for the static spinlocks, instead of the
dynamic ones (currently used), as proposed by David Härdeman on one
of his RFC patches.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reimplement the RC-5 decoder state machine. Code is now clear, and works
properly. It is also simpler than the previous implementations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous cleanup patch removed more than needed. Re-add the logic that
disable the decoders.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few hardware Remote Controller decoders, even using a standard protocol,
aren't able to provide the entire scancode. Due to that, the capability
of using other IR's are limited on those hardware.
Adds a way to indicate to ir-core what are the bits that the hardware
provides, from a scancode, allowing the addition of a complete IR table
to the kernel and allowing a limited support for changing the Remote
Controller on those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the decoders are state machine, there's no need to create
an ancillary buffer while decoding the protocol. Just call the decoders
code directly, event by event.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This decoder is also based on a state machine, just like the NEC protocol
decoder. It is pedantic in the sense that accepts only 14 bits. As there
are some variants that outputs less bits, it needs to be improved to also
handle those.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Andy Walls <awalls@md.metrocast.net> for pointing me his
code, that gave me some ideas to better implement it.
After some work with saa7134 bits, I found a way to catch both IRQ
edge pulses. By enabling it, the NEC decoder can now take both
pulse and spaces into account, making it more precise.
Instead of the old strategy of handling the events all at once,
this code implements a state machine. Due to that, it handles
individual pulse or space events, validating them against the
protocol, producing a much more reliable decoding.
With the new implementation, the protocol trailer bits are properly
handled, making possible for the repeat key to work.
Also, the code is now capable of handling both NEC and NEC extended
IR devices. With NEC, it produces a 16 bits code, while with NEC
extended, a 24 bits code is returned.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrites the keyup/keydown logic in drivers/media/IR/ir-keytable.c.
All knowledge of keystates etc is now internal to ir-keytable.c
and not scattered around ir-raw-event.c and ir-nec-decoder.c (where
it doesn't belong).
In addition, I've changed the API slightly so that ir_input_dev is
passed as the first argument rather than input_dev. If we're ever
going to support multiple keytables we need to move towards making
ir_input_dev the main interface from a driver POV and obscure away
the input_dev as an implementational detail in ir-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch rewrites much of the keytable code in
drivers/media/IR/ir-keytable.c.
The scancodes are now inserted into the array in sorted
order which allows for a binary search on lookup.
The code has also been shrunk by about 150 lines.
In addition it fixes the following bugs:
Any use of ir_seek_table() was racy.
ir_dev->driver_name is leaked between ir_input_register() and
ir_input_unregister().
ir_setkeycode() unconditionally does clear_bit() on dev->keybit
when removing a mapping, but there might be another mapping with
a different scancode and the same keycode.
This version has been updated to incorporate patch feedback from
Mauro Carvalho Chehab.
[mchehab@redhat.com: Fix a conflict with RC keytable breakup patches and input changes]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the remote keymaps were broken into separate modules,
get rid of the keycode tables that were hardcoded into ir-common.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the ugly keymap sequences, use the new rc-*.ko keymap
files. For now, it is still needed to have one keymap loaded, for the
RC code to work. Later patches will remove this depenency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A latter patch will reuse the ir_input_register with a different meaning.
Before it, change all occurrences to a temporary name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original Remote Controller approach were very messy: a big file,
that were part of ir-common kernel module, containing 64 different
RC keymap tables, used by the V4L/DVB drivers.
Better to break each RC keymap table into a separate module,
registering them into rc core on a process similar to the fs/nls tables.
As an userspace program is now in charge of loading those tables,
adds an option to allow the complete removal of those tables from
kernelspace.
Yet, on embedded devices like Set Top Boxes and TV sets, maybe the
only available input device is the IR. So, we should keep allowing
the usage of in-kernel tables, but a latter patch should change
the default to 'n', after giving some time for distros to add
the v4l-utils with the ir-keytable program, to allow the table
load via userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having all RC tables hardcoded on one file with
all tables there, add infrastructure for registering and dynamically
load the table(s) when needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big file with lots of keytables, create one include
file for each IR keymap.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usage of macros ensures that the proper namespace is being used
by all tables. It also makes easier to associate a keytable with
the name used inside the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Especially when IR needs to do polling, it generates lots of wakeups per
second. This makes no sense, if the input event device is closed.
Adds a callback handler to the IR hardware driver, to allow registering
an open/close ops.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IR is an alias for Infrared Remote, while RC is an alias for Remote
Controller.
While currently all implementations are with Infrared Remote Controller,
this subsystem is not meant to be used only by IR type of RC's. So,
as discussed on both linux-media and linux-input, the better is to
rename the subsystem as Remote Controller.
While, currently, the only application that uses the /sys/class/irrcv is
ir-keytable application, and its sysfs support works only with the
current linux-next code, it is still possible to change the userspace API
without the risk of breaking applications. So, better to rename this
sooner than later.
Later patches will be needed to rename the files and to move them away
from drivers/media, but this is not a critical issue. So, for now,
let's just change the name of the sysfs class/nodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the help of raw_register/raw_unregister, adds a sysfs group
associated with the decoder, inside the corresponding irrcv node.
Writing 1 to nec_decoder/enabled enables the decoder, while
writing 0 disables it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some decoders and a lirc_dev interface may need some other operations to work.
For example: IR device register/unregister and ir_keydown events may need to
be tracked.
As some operations can occur in interrupt time, and a lock is needed to prevent
un-registering a decode while decoding a key, the lock needed to be convert
into a spin lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of hardcoding the protocols into ir-core, add a register interface
for the IR protocol decoders, and convert ir-nec-decoder into a client of
ir-core.
With this approach, it is possible to dynamically load the needed IR protocols,
and to add a RAW IR interface module, registered as one IR raw protocol decoder.
This patch opens a way to register a lirc_dev interface to work as an userspace
IR protocol decoder.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At raw_decode mode, the key is processed after the end of a timer. The
previous code resets the timer every time something is received at the IR
port. While this works fine with IR's that don't implement repeat, like
Avermedia RM-JX IR, it keeps waiting until keydown, on IR's that implement
NEC repeat command, like the Terratec yellow.
The solution is to change the behaviour to do the timeout after the first
received data.
The timeout is currently set to 15 ms, as it works fine with NEC protcocol.
It may need some adjustments to support other protocols and to better handle
spurious detections that may happen with some IR sensors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a method to pass IR raw pulse/code events into ir-core. This is
needed in order to support LIRC. It also helps to move common code
from the drivers into the core.
In order to allow testing, it implements a simple NEC protocol decoder
at ir-nec-decoder.c file. The logic is about the same used at saa7134
driver that handles Avermedia M135A and Encore FM53 boards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, both driver and keytable names are exported to userspace. This
will help userspace to decide when a table need to be replaced
by another one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the ir-sysfs approach to create irrcv0 as a device, instead of
using class_dev. Also, change the way input is registered, in order
to make its parent to be the irrcv device.
Due to this change, now the event device is created under
/sys/class/ir/irrcv class:
/sys/class/irrcv/irrcv0/
|-- current_protocol
|-- device -> ../../../1-3
|-- input9
| |-- capabilities
| | |-- abs
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The HID layer has some scan codes of the form 0xffbc0000 for logitech
devices which do not work if scancode is typed as signed int, so we need
to switch to unsigned it instead. While at it keycode being signed does
not make much sense either.
Acked-by: Márton Németh <nm127@freemail.hu>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds remote support for the Kworld 315U device
I have added the change for the IR_TYPE_NEC that Mauro suggested.
Note: I believe I got most of the mappings correct. Though the
source and shutdown button probably could be mapped to something
better.
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Franklin Meng <fmeng2002@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fix Video/Sound support "Leadtek winfast tv usbii deluxe".
Now, it is working Stereo, IR, Radio, TV, Svideo and Composite.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Free ir_dev before exit.
Found by cppcheck.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the declaration of the sysfs attributes for IR's, which
must be a NULL-terminated array of struct attribute *.
Without this patch, my machine crashes when inserting a DVB card.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/buildtest/v4l-dvb-master/v4l/ir-keytable.c: In function 'ir_setkeycode':
/home/v4l/buildtest/v4l-dvb-master/v4l/ir-keytable.c:190: warning: 'newkeymap' may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As currently most drivers don't define ir_dev->props, we shouldn't assume
that this field is defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add sysfs skeleton to export remote controller information via
/sys/class/irrcv.
For now, the code doesn't do much. It just exports an attribute that
is meant to report and control the IR protocol used by the keytable.
However, the callbacks for this new attribute weren't set yet.
Also, it lacks symlinks to the used event interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll need to register a sysfs class for the IR devices. As such, the better
is to have the input_register_device()/input_unregister_device() inside
the ir register/unregister functions.
Also, solves a naming problem with V4L ir_input_init() function, that were,
in fact, registering a device.
While here, do a few cleanups at budget-ci IR logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ir_input_free does more than just freeing the keytab. Better to
rename it as ir_input_unregister.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move non-V4L specific stuff from ir-functions ir_input_init() into
a new function to register ir devices: ir_input_register().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
