TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add HAVE_PATA_PLATFORM to select the pata platform driver
to ensure that we do not end up with a long 'depends on' list
when other users of this driver turn up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Chip errata sometimes prevents reliable use of PIO commands which involve
more than a single DRQ (data request). In normal operation, libata should
not generate such PIO commands (uses DMA instead), but they could be sent
in via SG_IO from userspace.
A full workaround might be to break up such commands into sequences
of single DRQ ones, but that's just way too complex for something
that doesn't normally happen in real life.
So, allow the attempt (it often works, despite the errata),
but log the event for reference when somebody screams.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The early chipsets cannot safely handle Async Notification (AN),
but 6041/6081 chip revision "C0" (and newer) can handle it.
So allow AN for "C0" and higher.
This enables use of hotplug on PMP ports for the 6041/6081 PCI Rev.9 chips.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no reason to check whether to use DMA or not for no data
commands. Don't do it. While at it, make local variable using_pio in
atapi_xlat() set iff ATAPI_PROT_PIO is going to be used and rename
ata_check_atapi_dma() to atapi_check_dma() for consistency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
JMB361 has only one port but reports it has two causing longish probe
failure on the second one. Quirk it.
Reported by Gajo Petrovic in bz 10911.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gajo Petrovic <gajo01@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
besides it apparently being useful only in 2.6.24 (the changes in 2.6.25
really mean that it could be converted back to a single-stage mechanism),
I'm seeing an issue in Xen Dom0 kernels, which is caused by the calling
of gart_to_virt() in the second stage invocations of the destroy function.
I think that besides this being a real issue with Xen (where
unmap_page_from_agp() is not just a page table attribute change), this
also is invalid from a theoretical perspective: One should not assume that
gart_to_virt() is still valid after unmapping a page. So minimally (keeping
the 2-stage mechanism) a patch like the one below would be needed.
Jan
Signed-off-by: Dave Airlie <airlied@redhat.com>
add a new PCI ID and remove an old dodgy one, include the explaination
in the commented code so nobody readds later.
(davej also sent the pci id addition).
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/uverbs: Fix check of is_closed flag check in ib_uverbs_async_handler()
RDMA/nes: Fix off-by-one in nes_reg_user_mr() error path
When a driver rejects a frame in it's ->tx() callback, it must also
stop queues, otherwise mac80211 can go into a loop here. Detect this
situation and abort the loop after five retries, warning about the
driver bug.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1ae5c187 ("IB/uverbs: Don't store struct file * for event
files") changed the way that closed files are handled in the uverbs
code. However, after the conversion, is_closed flag is checked
incorrectly in ib_uverbs_async_handler(). As a result, no async
events are ever passed to applications.
Found by: Ronni Zimmerman <ronniz@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rename and reorder some prompts and modify some help texts.
The result:
-------------------- IEEE 1394 (FireWire) support --------------------
*** Enable only one of the two stacks, unless you know what you are doing ***
New FireWire stack, EXPERIMENTAL
OHCI-1394 controllers
Storage devices (SBP-2 protocol)
Stable FireWire stack
OHCI-1394 controllers
PCILynx controller
Storage devices (SBP-2 protocol)
Enable replacement for physical DMA in SBP2
IP over 1394
raw1394 userspace interface
video1394 userspace interface
dv1394 userspace interface (deprecated)
Excessive debugging output
The old prompts for reference:
-------------------- IEEE 1394 (FireWire) support --------------------
IEEE 1394 (FireWire) support - alternative stack, EXPERIMENTAL
Support for OHCI FireWire host controllers
Support for storage devices (SBP-2 protocol driver)
IEEE 1394 (FireWire) support
*** Subsystem Options ***
Excessive debugging output
*** Controllers ***
Texas Instruments PCILynx support
OHCI-1394 support
*** Protocols ***
OHCI-1394 Video support
SBP-2 support (Harddisks etc.)
Enable replacement for physical DMA in SBP2
IP over 1394
OHCI-DV I/O support (deprecated)
Raw IEEE1394 I/O support
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Emphasize the recommendation to build only one stack.
Trim the prompts to better fit into short attention spans.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If the low-level driver failed to initialize a card properly without
noticing it, fw-core was blocked indefinitely when trying to send a
PHY config packet. This hung up the events kernel thread, e.g. locked
up keyboard input.
https://bugzilla.redhat.com/show_bug.cgi?id=444694https://bugzilla.redhat.com/show_bug.cgi?id=446763
This problem was introduced between 2.6.25 and 2.6.26-rc1 by commit
2a0a259049 "firewire: wait until PHY
configuration packet was transmitted (fix bus reset loop)".
The solution is to wait with timeout. I tested it with 7 different
working controllers and 1 non-working controller. On the working ones,
the packet callback complete()s usually --- but not always --- before a
timeout of 10ms. Hence I chose a safer timeout of 100ms.
On the few tests with the non-working controller ALi M5271, PHY config
packet transmission always timed out so far. (Fw-ohci needs to be fixed
for this controller independently of this deadline fix. Often the core
doesn't even attempt to send a phy config because not even self ID
reception works.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The messages which can be enabled by fw-ohci's debug module parameter
are changed from KERN_DEBUG to KERN_NOTICE level and uniformly prefixed
with "firewire_ohci: ". This further simplifies communication with
users when we ask them to capture debug messages.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Callers of fill_bus_reset_event() have to take card->lock. Otherwise
access to node data may oops if node removal is in progress.
A lockless alternative would be
- event->local_node_id = card->local_node->node_id;
+ tmp = fw_node_get(card->local_node);
+ event->local_node_id = tmp->node_id;
+ fw_node_put(tmp);
and ditto with the other node pointers which fill_bus_reset_event()
accesses. But I went the locked route because one of the two callers
already holds the lock. As a bonus, we don't need the memory barrier
anymore because device->generation and device->node_id are written in
a card->lock protected section.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
OHCI 1.1 clause 5.10 requires that selfIDBufferPtr is valid when a 1 is
written into LinkControl.rcvSelfID.
This driver bug has so far not been known to cause harm because most
chips obviously accept a later selfIDBufferPtr write, at least before
HCControl.linkEnable is written.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
We want the rcvPhyPkt bit in LinkControl off before we start using the
chip. However, the spec says that the reset value of it is undefined.
Hence switch it explicitly off.
https://bugzilla.redhat.com/show_bug.cgi?id=244576#c48 shows that for
example the nForce2 integrated FireWire controller seems to have it on
by default.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
header_length and payload_length are filled with random data if an
unknown tcode was read from the AR buffer (i.e. if the AR buffer
contained invalid data).
We still need a better strategy to recover from this, but at least
handle_ar_packet now doesn't return out of bound buffer addresses
anymore.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
BUG() at this place is wrong. (Unless if the low level driver would
already do higher-level input validation of incoming request headers.)
Invalid incoming requests or bugs in the controller which corrupt the
AR-req buffer needlessly crashed the box because this is run in tasklet
context.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] dpt_i2o: Add PROC_IA64 define
[SCSI] scsi_host regression: fix scsi host leak
[SCSI] sr: fix corrupt CD data after media change and delay
This patch takes a step towards making rcutorture more brutal by allowing
the test to be automatically periodically paused, with the default being
to run the test for five seconds then pause for five seconds and repeat.
This behavior can be controlled using a new "stutter" module parameter, so
that "stutter=0" gives the old default behavior of running continuously.
Starting and stopping rcutorture more heavily stresses RCU's interaction
with the scheduler, as well as exercising more paths through the
grace-period detection code.
Note that the default to "shuffle_interval" has also been adjusted from
5 seconds to 3 seconds to provide varying overlap with the "stutter"
interval.
I am still unable to provoke the failures that Alexey has been seeing,
even with this patch, but will be doing a few additional things to beef
up rcutorture.
Suggested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When we demote a slice from 64k to 4k, and we are about to insert an
HPTE for a 4k subpage and we notice that there is an existing 64k
HPTE, we first invalidate that HPTE before inserting the new 4k
subpage HPTE. Since the bits that encode which hash bucket the old
HPTE was in overlap with the bits that encode which of the 16 subpages
have HPTEs, we need to clear out the subpage HPTE-present bits before
starting to insert HPTEs for the 4k subpages. If we don't do that, we
can erroneously think that a subpage already has an HPTE when it
doesn't.
That in itself wouldn't be such a problem except that when we go to
update the HPTE that we think is present on machines with a
hypervisor, the hypervisor can tell us that the HPTE we think is there
is actually there even though it isn't, which can lead to a process
getting stuck in a loop, continually faulting. The reason for the
confusion is that the AVPN (abbreviated virtual page number) we are
looking for in the HPTE for a 4k subpage can actually match the AVPN
in a stale HPTE for another 64k page. For example, the HPTE for
the 4k subpage at 0x84000f000 will be in the same hash bucket and have
the same AVPN as the HPTE for the 64k page at 0x8400f0000.
This fixes the code to clear out the subpage HPTE-present bits.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A recent commit added support for the new 440x6 and 464 cores that have the
added WL1, IL1I, IL1D, IL2I, and ILD2 bits for the caching attributes in the
TLBs. The new bits were cleared in the finish_tlb_load function, however a
similar bit of code was missed in the DataStorage interrupt vector.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
genetlink has a circular locking dependency when dumping the registered
families:
- dump start:
genl_rcv() : take genl_mutex
genl_rcv_msg() : call netlink_dump_start() while holding genl_mutex
netlink_dump_start(),
netlink_dump() : take nlk->cb_mutex
ctrl_dumpfamily() : try to detect this case and not take genl_mutex a
second time
- dump continuance:
netlink_rcv() : call netlink_dump
netlink_dump : take nlk->cb_mutex
ctrl_dumpfamily() : take genl_mutex
Register genl_lock as callback mutex with netlink to fix this. This slightly
widens an already existing module unload race, the genl ops used during the
dump might go away when the module is unloaded. Thomas Graf is working on a
seperate fix for this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 608961a5ec.
The problem is that the mac80211 stack not only needs to be able to
muck with the link-level headers, it also might need to mangle all of
the packet data if doing sw wireless encryption.
This fixes kernel bugzilla #10903. Thanks to Didier Raboud (for the
bugzilla report), Andrew Prince (for bisecting), Johannes Berg (for
bringing this bisection analysis to my attention), and Ilpo (for
trying to analyze this purely from the TCP side).
In 2.6.27 we can take another stab at this, by using something like
skb_cow_data() when the TX path of mac80211 ends up with a non-NULL
tx->key. The ESP protocol code in the IPSEC stack can be used as a
model for implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
The unix_dgram_sendmsg routine implements a (somewhat crude)
form of receiver-imposed flow control by comparing the length of the
receive queue of the 'peer socket' with the max_ack_backlog value
stored in the corresponding sock structure, either blocking
the thread which caused the send-routine to be called or returning
EAGAIN. This routine is used by both SOCK_DGRAM and SOCK_SEQPACKET
sockets. The poll-implementation for these socket types is
datagram_poll from core/datagram.c. A socket is deemed to be writeable
by this routine when the memory presently consumed by datagrams
owned by it is less than the configured socket send buffer size. This
is always wrong for connected PF_UNIX non-stream sockets when the
abovementioned receive queue is currently considered to be full.
'poll' will then return, indicating that the socket is writeable, but
a subsequent write result in EAGAIN, effectively causing an
(usual) application to 'poll for writeability by repeated send request
with O_NONBLOCK set' until it has consumed its time quantum.
The change below uses a suitably modified variant of the datagram_poll
routines for both type of PF_UNIX sockets, which tests if the
recv-queue of the peer a socket is connected to is presently
considered to be 'full' as part of the 'is this socket
writeable'-checking code. The socket being polled is additionally
put onto the peer_wait wait queue associated with its peer, because the
unix_dgram_sendmsg routine does a wake up on this queue after a
datagram was received and the 'other wakeup call' is done implicitly
as part of skb destruction, meaning, a process blocked in poll
because of a full peer receive queue could otherwise sleep forever
if no datagram owned by its socket was already sitting on this queue.
Among this change is a small (inline) helper routine named
'unix_recvq_full', which consolidates the actual testing code (in three
different places) into a single location.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, tun.c running in TUN_TUN_DEV mode will set the protocol of
packet to IPv4 if TUN_NO_PI is set. My program failed to work when I
assumed that the driver will check the first nibble of packet,
determine IP version and set the appropriate protocol.
Signed-off-by: Ang Way Chuang <wcang@nav6.org>
Acked-by: Max Krasnyansky <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1 driver tries to determine the MAC address thusly:
- If an EEPROM exists, read the MAC address from EEPROM and
validate it.
- If an EEPROM doesn't exist, try to read a MAC address from
SPI flash.
- If that fails, try to read a MAC address directly from the
MAC Station Address register.
- If that fails, assign a random MAC address provided by the
kernel.
We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition. Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.
This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: Radu Cristescu <advantis@gmx.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.
This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ibm_newemac driver requires ether_crc to be defined. Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:
LD .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1
This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use max not min to enforce a lower limit on the max I/O size.
This bug was introduced by "fuse: fix max i/o size calculation" (commit
e5d9a0df07).
Thanks to Brian Wang for noticing.
Reported-by: Brian Wang <ywang221@hotmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Szabolcs Szakacsits <szaka@ntfs-3g.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added !vmlinux.lds.h to .gitignore because it would otherwise be ignored.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most users by far do not care about the exact return value (they only
really care about whether the copy succeeded in its entirety or not),
but a few special core routines actually care deeply about exactly how
many bytes were copied from user space.
And the unrolled versions of the x86-64 user copy routines would
sometimes report that it had copied more bytes than it actually had.
Very few uses actually have partial copies to begin with, but to make
this bug even harder to trigger, most x86 CPU's use the "rep string"
instructions for normal user copies, and that version didn't have this
issue.
To make it even harder to hit, the one user of this that really cared
about the return value (and used the uncached version of the copy that
doesn't use the "rep string" instructions) was the generic write
routine, which pre-populated its source, once more hiding the problem by
avoiding the exception case that triggers the bug.
In other words, very special thanks to Bron Gondwana who not only
triggered this, but created a test-program to show it, and bisected the
behavior down to commit 08291429cf ("mm:
fix pagecache write deadlocks") which changed the access pattern just
enough that you can now trigger it with 'writev()' with multiple
iovec's.
That commit itself was not the cause of the bug, it just allowed all the
stars to align just right that you could trigger the problem.
[ Side note: this is just the minimal fix to make the copy routines
(with __copy_from_user_inatomic_nocache as the particular version that
was involved in showing this) have the right return values.
We really should improve on the exceptional case further - to make the
copy do a byte-accurate copy up to the exact page limit that causes it
to fail. As it is, the callers have to do extra work to handle the
limit case gracefully. ]
Reported-by: Bron Gondwana <brong@fastmail.fm>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(which didn't have this problem), and since
most users that do the carethis was very hard to trigger, but
