w1 does not need to multicast its state to several groups at once,
and upcoming netlink changes will not allow bitmask for groups anyway.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following possible cleanups/fixes:
- use C99 struct initializers
- make a few arrays and structs static
- remove a few uses of literal 0 as NULL pointer
- use convenience function instead of cast+dereference in bnx2_ioctl()
- remove superfluous casts to u8 * in calls to readl/writel
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the usage of packet type into the SKB control
buffer. After this patch it is now possible to shrink the sk_buff
structure and redefine its pkt_type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the sparse warnings "implicit cast to nocast type"
for the priority or gfp_mask parameters of the memory allocations.
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the virtual HCI driver. It also adds support for
the dynamic minor device number allocation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found a bug while reviewing the patches the second time.
The TG3_FLAG_TXD_MBOX_HWBUG flag is set after the register access
methods have been determined. This patch fixes it by moving it up before
the various access methods are assigned.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register write to register 0x68 to restart interrupts is unnecessary
as the interrupt wasn't masked in that register by the irq handler. This
will save one register write in the fast path.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the new workaround for 5703 A1/A2 if it is behind
certain ICH bridges. The workaround disables memory and uses config.
cycles only to access all registers. The 5702/03 chips can mistakenly
decode the special cycles from the ICH chipsets as memory write cycles,
causing corruption of register and memory space. Only certain ICH
bridges will drive special cycles with non-zero data during the address
phase which can fall within the 5703's address range. This is not an ICH
bug as the PCI spec allows non-zero address during special cycles.
However, only these ICH bridges are known to drive non-zero addresses
during special cycles.
The indirect_lock is also changed to spin_lock_irqsave from spin_lock_bh
because it is used in irq handler when using the indirect method to
disable interrupts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the mailbox read method and also adds an inline function
tw32_mailbox_f() for mailbox writes that require read flush.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds various dedicated register read/write methods for the
existing workarounds, including PCIX target workaround, write with read
flush, etc. The chips that require these workarounds will use these
dedicated access functions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the basic function pointers to do register accesses in
the fast path. This was suggested by David Miller. The idea is that
various register access methods for different hardware errata can easily
be implemented with these function pointers and performance will not be
degraded on chips that use normal register access methods.
The various register read write macros (e.g. tw32, tr32, tw32_mailbox)
are redefined to call the function pointers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code contributed by Stephen Hemminger.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove bogus code for compiling netlink as module
- Add module refcounting support for modules implementing a netlink
protocol
- Add support for autoloading modules that implement a netlink protocol
as soon as someone opens a socket for that protocol
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, set it in one place, namely the beginning of
netif_receive_skb().
Based upon suggestions from Jamal Hadi Salim.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding just wants the device before the skb_bond()
decapsulation occurs, so simply pass that original
device into packet_type->func() as an argument.
It remains to be seen whether we can use this same
exact thing to get rid of skb->input_dev as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the private element from skbuff, that is only used by
HIPPI. Instead it uses skb->cb[] to hold the additional data that is
needed in the output path from hard_header to device driver.
PS: The only qdisc that might potentially corrupt this cb[] is if
netem was used over HIPPI. I will take care of that by fixing netem
to use skb->stamp. I don't expect many users of netem over HIPPI
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the "list" member of struct sk_buff, as it is entirely
redundant. All SKB list removal callers know which list the
SKB is on, so storing this in sk_buff does nothing other than
taking up some space.
Two tricky bits were SCTP, which I took care of, and two ATM
drivers which Francois Romieu <romieu@fr.zoreil.com> fixed
up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This patch adds back the code that was taken out, thus re-enabling:
* The PHY Layer to initialize without crashing
* Drivers to actually connect to PHYs
* The entire PHY Control Layer
This patch is used by the gianfar driver, and other drivers which are in
development.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- changes license of all code from OSL+GPL to plain ole GPL
- except for NVIDIA, who hasn't yet responded about sata_nv
- copyright holders were already contacted privately
- adds info in each driver about where hardware/protocol docs may be
obtained
- where I have made major contributions, updated copyright dates
Bugfix (usage of uninitialized pointer in zfcp_port_dequeue) and compile
fixes for the zfcp device driver.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[ Same race and same patch also by Steven Rostedt <rostedt@goodmis.org> ]
I have a laptop (G3 powerbook) which will pretty reliably hit a race
between con_open and con_close late in the boot process and oops in
vt_ioctl due to tty->driver_data being NULL.
What happens is this: process A opens /dev/tty6; it comes into
con_open() (drivers/char/vt.c) and assign a non-NULL value to
tty->driver_data. Then process A closes that and concurrently process
B opens /dev/tty6. Process A gets through con_close() and clears
tty->driver_data, since tty->count == 1. However, before process A
can decrement tty->count, we switch to process B (e.g. at the
down(&tty_sem) call at drivers/char/tty_io.c line 1626).
So process B gets to run and comes into con_open with tty->count == 2,
as tty->count is incremented (in init_dev) before con_open is called.
Because tty->count != 1, we don't set tty->driver_data. Then when the
process tries to do anything with that fd, it oopses.
The simple and effective fix for this is to test tty->driver_data
rather than tty->count in con_open. The testing and setting of
tty->driver_data is serialized with respect to the clearing of
tty->driver_data in con_close by the console_sem. We can't get a
situation where con_open sees tty->driver_data != NULL and then
con_close on a different fd clears tty->driver_data, because
tty->count is incremented before con_open is called. Thus this patch
eliminates the race, and in fact with this patch my laptop doesn't
oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[ Same patch
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
in http://marc.theaimsgroup.com/?l=linux-kernel&m=112450820432121&w=2 ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a severe problem with 2.6.13-rc7.
Due to recent SCSI changes it is not possible to add any LUNs to the zfcp
device driver anymore. With registration of remote ports this is fixed.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Acked-by: James Bottomley <jejb@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I know that scsi procfs is legacy code but this is a fix for a memory leak.
While reading through sg.c I realized that the implementation of
/proc/scsi/sg/devices with seq_file is leaking memory due to freeing the
pointer returned by the next() iterator method. Since next() might return
NULL or an error this is wrong. This patch fixes it through using the
seq_files private field for holding the reference to the iterator object.
Here is a small bash script to trigger the leak. Use slabtop to watch
the size-32 usage grow and grow.
#!/bin/sh
while true; do
cat /proc/scsi/sg/devices > /dev/null
done
Signed-off-by: Jan Blunck <j.blunck@tu-harburg.de>
Acked-by: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed race between submitting streaming URBs in the driver and starting
the actual transfer in hardware (demodulator and USB controller) which
sometimes lead to garbled data transfers. URBs are now submitted first,
then the transfer is enabled. Dibusb devices and clones are now fully
functional again.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a bug in the capifs initialization code, where the
filesystem is not unregistered if kern_mount() fails.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When acpi_sleep_prepare was moved into a shutdown method we
started calling it for all shutdowns.
It appears this triggers some systems to power off on reboot.
Avoid this by only calling acpi_sleep_prepare if we are going to power
off the system.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Both revisions share the same PCI device ID and vendor ID but revision 2
of the device uses SysKonnect's chipset whereas revision 3 of the device
uses Realtek's 8169 chipset.
Credit goes to Christiaan Lutzer <mythtv.lutzer@gmail.com> for reporting
the issue and giving the actual value for the different revisions.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Rewrite the mkiss driver to make it SMP-proof following the example of
6pack.c.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't check type of sax25_family; dev_set_mac_address has already done
that before and anyway, the type to check against would have been
ARPHRD_AX25. We only got away because AF_AX25 and ARPHRD_AX25 both happen
to be defined to the same value.
Don't check sax25_ndigis either; it's value is insignificant for the
purpose of setting the MAC address and the check has shown to break
some application software for no good reason.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I dropped the timer initialization bits by accident when sending the
p-persistence fix. This patch gets the driver to work again on halfduplex
links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix bugs for unlikely edge cases noticed by Douglas Gilbert:
- When READ(6)/WRITE(6) sector count == 0, treat it as 256 sectors
- For other READ(x)/WRITE(x), when sector count == 0, error.
We don't support successfully completing zero-length transfers at
this time.
Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently we may have work scheduled in default kernel workqueue when
the device is going down. The device could get freed before this
workqueue gets serviced. I am actually seeing this causing system
hangs.
The following patch fixes this by using ipoib_workqueue which gets
flushed when the device is going down.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
