No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.102.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 is a dual port chip that has a shared MDIO bus design. While
it is impossible for one function to interface with the wrong phy, that
function still needs to know which MDIO bus address to use when
interfacing with its own phy. This patch adds code to determine which
MDIO bus address to use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds NVRAM detection routines for the 5717.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5717 asic rev.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RSS is enabled, the status block format changes slightly. The
"rx_jumbo_consumer", "reserved", and "rx_mini_consumer" members get
mapped to the other three rx return ring producer indexes. This patch
introduces a new per-interrupt member which identifies which location
in the status block a particular vector should look for return ring
updates.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multivector RSS is enabled, the first interrupt vector is only used
to report link interrupts and error conditions. This patch changes the
code so that rx and tx ring resources are not allocated for this vector.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code needed to enable RSS.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to tune the coalescing parameters for the other
msix vectors.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to enable and disable the rest of the NAPI
instances.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes the additional transmit rings to the kernel and makes
the necessary modifications to transmit, open, and close paths.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes up two spots that need attention now that msix support
has been added.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to assign status block, tx producer ring and rx
return ring resources needed for the other interrupt vectors.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 assigns mailbox locations to interrupt vectors in a rather
non-intuitive way. (Much of the complexity stems from legacy
compatibility issues.) This patch implements the assignment scheme.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds MSI-X support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to support multiple interrupt vectors around the
kernel's interrupt API.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves most of the chip ring setup logic into a separate
function. This will make it easier to verify the multi ring setup
changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each interrupt vector has its own bit in the host coalescing register to
force that vector's status block to be updated and generate an
interrupt. This patch adds a member to the per-interrupt structure
that records which bit belongs to that vector.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch inlines the code of tg3_cond_int() into the function's only
callsite. This prep work makes the following patch cleaner.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aup->mii_bus->irq allocation may fail, prevent a dereference of NULL.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
B0_CTST is a 24bit register according to the vendor driver (sk98lin).
A 16bit read on B0_CTST will always return 0 for Y2_VAUX_AVAIL (1<<16),
so use a 32bit read when testing Y2_VAUX_AVAIL
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor similar two sections of code that free buffers into one.
Only call tx_init if all buffer allocations succeed.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Observed by Mike McCormack.
The LED bit here is just a software controlled value used to
turn on one of the LED's on some boards. The register value was wrong,
which could have been causing some power control issues.
Get rid of problematic define use the correct mask.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tun always has an embeedded struct sock,
use sk and sk_receive_queue fields instead of
duplicating them in tun_struct.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can speedup ether addresses compares using compare_ether_addr_64bits()
instead of memcmp(). We make sure all operands are at least 8 bytes long and
16bits aligned (or better, long word aligned if possible)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To speedup ether addresses compares, we can use compare_ether_addr_64bits()
(all operands are guaranteed to be at least 8 bytes long)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 82599 multi speed fiber case when driver is loaded without any
cable and reconnecting the cable with a 1G partner does not bring
up the link in 1Gb mode. When there is no link we first setup the link
at 10G & 1G and then try to re-establish the link at highest speed 10G
and thereby changing autoneg_advertised value to highest speed 10G.
After connecting back the cable to a 1G link partner we never try 1G
as autoneg advertised value is changed to link at 10G only. The
following patch fixes the issue by properly initializing the
autoneg_advertised value just before exiting from link setup routine.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling the Rx and Tx data arbiters prior to configuration changes,
the arbiters were not being shut down properly. This can create a race
in the DCB hardware blocks, and potentially hang the arbiters. Also, the
Tx descriptor arbiter shouldn't be disabled when applying configuration
changes; disabling this arbiter can cause a Tx hang.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link code cleanup: a number of redundant functions and MAC variables are cleaned up,
with some functions being consolidated into a single-purpose code path.
Removed following deprecated link functions and mac variables
* ixgbe_setup_copper_link_speed_82598
* ixgbe_setup_mac_link_speed_multispeed_fiber
* ixgbe_setup_mac_link_speed_82599
* mac.autoneg, mac.autoneg_succeeded, phy.autoneg_wait_to_complete
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling VLAN filters (VFE) when the primary interface is brought up
(per commit 78ed11a) has caused problems for some users who manage
their systems using IPMI over a VLAN. This is because when the driver
enables the VLAN filter, this same filter table is enabled for the
management channel, and the table is initially empty, which means that
the IPMI/VLAN packets are filtered out and not received by the BMC.
This is a problem only on e1000 class adapters, as it is only
on e1000 that the filter table is common to the management and host
streams.
With this change, filtering is only enabled when one or more host VLANs
exist, and is disabled when the last host VLAN is removed. VLAN filtering
is always disabled when the primary interface is in promiscuous mode,
and will be (re)enabled if VLANs exist when the interface exits
promiscuous mode.
Note that this does not completely resolve the issue for those using VLAN
management, because if the host adds a VLAN, then the above problem
occurs when that VLAN is enabled. However, it does mean the there is no
problem for configurations where management is on a VLAN and the host is
not.
A complete solution to this issue would require further driver changes.
The driver would need to discover if (and which) management VLANs are
active before enabling VLAN filtering, so that it could ensure that the
managed VLANs are included in the VLAN filter table. This discovery
requires that the BMC identifies its VLAN in registers accessible
to the driver, and at least on Dell PE2850 systems the BMC does not
identify its VLAN to allow such discovery. Intel is pursuing this issue
with the BMC vendor.
Signed-off-by: Dave Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dcbnl_rtnl_ops.setapp/getapp to set or get the current user
priority bitmap for the given application protocol. Currently, 82599 only
supports setapp/getapp for Fiber Channel over Ethernet (FCoE) protocol.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to the net_device_ops.ndo_fcoe_enable/disable for 82599. This
consequently allows us to dynamically turn FCoE offload feature on or off
upon incoming calls to ndo_fcoe_enable/disable. When this happens, FCoE offload
features are enabled/disabled accordingly, and this is regardless of whether
DCB being turned on or not.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are all drivers that don't touch real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all the pcmcia network drivers for netdev_tx_t.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
