Add id for the Hewlett-Packard LD220-HP POS pole display.
Bus 002 Device 002: ID 03f0:3524 Hewlett-Packard
Signed-off-by: Mike Provencher <mike.provencher@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver transfers firmware. It may just as well set the correct
configuration.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the "Superial" USB-Serial converter to pl2303 so that it
is detected, by the correct driver. Adds the relevant vendor:product
(5372:2303) to the device tables in pl2303.c & pl2303.h. The patch has
been tested against 2.6.24-22-generic.
Signed-off-by: Matthew D Arnold <matthew.arnold-1@uts.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Someone on rmweb reminded me this had been overlooked from ages ago..
Add the identifiers for the Sprog II USB. This is a DCC control interface
using the FTDI-SIO hardware: http://www.sprog-dcc.co.uk/. People have been
using it with insmod options for ages, this just puts it into the driver
data.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[Folded together as one diff from 3]
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch which adds IDs for AKTAKOM USB->RS232 cable
(http://www.aktakom.ru/product/kio/ace-1001.htm) is attached.
From: M Kondrin <mkondrin@hppi.troitsk.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enfora GSM2228 based on Cygnal Integrated Products chip uses the same
cp2101 driver.
Signed-off-by: Damir N Abdullin <damir@mimas.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds YISO u893 usb modem vendor and product ID to option.c.
I had a better experience using this modification and the same system.
Signed-off-by: Leslie Harlley Watter <leslie@watter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we close we must clear the extra reference we got when we read
port->tty. Setting the port tty NULL will clear the kref held by the driver
but not the one we obtained ourselves while doing the lookup.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Helge Hafting <helge.hafting@aitel.hist.no>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In this patch, we want to do one thing: add more Huawei product IDs into the
USB driver. Then it can support more Huawei data card devices. So to declare
the unusual device for new Huawei data card devices in unusual_devs.h and to
declare more new product IDs in option.c.
To modify the data value and length in the function of
usb_stor_huawei_e220_init in initializers.c That's because based on the USB
standard, while sending SET_FETURE_D to the device, it requires the
corresponding data to be zero, and its sending length also must be zero. In
our old solution, it can be compatible with our WCDMA data card devices, but
can not support our CDMA data card devices. But in this new solution, it can
be compatible with all of our data card devices.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The AnyData ADU-310 series of wireless modems uses the same product ID as the ADU-E100 series.
Signed-off-by: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves dbg calls to dev_dbg where possible. It also fixes some
issues with a previous submission aiming to do the same thing.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Oceanic PID to ftdi_sio driver
Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a PID of 0xf460. The
attached patch adds that pid to ftdi_sio; driver connects to my VT3
after that.
Signed-off-by: Vladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate device ids which are now supported by drivers/usb/net/hso.c
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.
Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the private check for the termios_initialized for
the pl2303 usb driver. It forced the baud to 9600 on the first call
to pl2303_set_termios()
Based on the tty changes in the 2.6.27 kernel, the termios passed to
the *_set_termios functions is always populated the first time.
This means there is no need to privately initialize the settings the
first time, and doing so will not allow the use of the kernel
parameter "console=ttyUSB0,115200" as an example.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some reason the oti6858 driver undefines and redefines the dbg
macro. This makes it spew debugging messages at KERN_INFO instead of
KERN_DEBUG.
This patch removes the undef and define making the driver log like every
other USB serial driver.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While making some other changes to ti_usb_3410_5052, I noticed that the
changes made to move the firmware loading to a separate function are
broken (in ti_download_firmware(), status is set to -ENOMEM and never
changed). This means the driver will never initialize the device
properly. It looks like status was supposed to get the result of
ti_do_download().
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This hardware needs the pl2303 hack in order to work properly :(
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was trying to figure out why my device wasn't supported by the
drivers/usb/serial/sierra.c driver, while looking throught the device
IDs I spotted what I believe to be a typo in the device IDs. Please
apply the following patch
If you look down further, there is another HP wireless broadband card,
which has a vendor ID of 03f0, like my device. Below is my "lsusb -v
-d 03f0:1b1d".
Bus 001 Device 005: ID 03f0:1b1d Hewlett-Packard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x03f0 Hewlett-Packard
idProduct 0x1b1d
bcdDevice 0.01
iManufacturer 1 HP
iProduct 2 HP ev2200 1xEV-DO Broadband Wireless Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 3 Data Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 128
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
From: Tony Murray <murraytony@gmail.com>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds devices to the sierra driver and rev's the driver version.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hw interface drivers for the usb serial devices deference the tty
structure to set up the parameters for the initial console. The tty
structure should be passed as a parameter to the set_termios() call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch support NTT DoCoMo A2502 3G/HSDPA modem on option driver.
It is produced by AnyDATA Corp. and also sold as KT Freetelecom (Korea) ADU 620UW.
It support 3.6Mbps/7.2Mbps hight speed communication.
I have tested A2502 with NTT DoCoMo MoperaU ISP service.
Signed-off-by: Hiroshi Miura <miurahr@nttdata.co.jp>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Product ID for the BandLuxe C150/C250 3.5G data
card series from BandRich Inc.
After detection, the data card works fine.
It was patched against kernel 2.6.27-rc1 with -mm patch
Signed-off-by: Leon Leong <upleong@bandrich.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Moves responsbility of TRU-Install (i.e. ZeroCD) to the usb-storage
driver. See patch 04/04 of this set.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the method by which the number of ports per interface is
assigned so that it is more dynamic and calculated on the fly (as opposed to
hard coding it). This will allow for faster and easier addition of products.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Very minor changes to clean up sierra code. Adds a prefix to debug messages so
that Sierra messages are easily recognized. Removes extraneous code.
This targets kernel 2.6.26-rc9
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB ID 4348:5523 is handled by the ch341 driver. Remove it from the
pl2023 driver.
Reverts 002e8f2c80.
Signed-off-by: Tollef Fog Heen <tfheen@err.no>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
