With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a check after the for loops to see if we found what we were looking
for or if we reached the end of the list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The rc map table were corrected thanks to Giorgio input and tests.
Reported-by: Giorgio Vazzana <mywing81@gmail.com>
Tested-by: Giorgio Vazzana <mywing81@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some symbols at saa7134-input that are used on saa7134
and vice-versa. Due to that, module install fails.
So, partially revert commit 9f495cf7d691c99bf7bdcec9f35fcfdad2cf9ae9.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_waiton() must unlock and relock ext_lock if it has to wait.
For that to happen it needs the videobuf_queue pointer.
Don't attempt to unlock/relock q->ext_lock unless it was locked in the
first place.
vb->state has to be protected by a spinlock to be safe.
This patch is based on code from Mauro Carvalho Chehab <mchehab@redhat.com>.
[mchehab@redhat.com: add extra argument to a few missing places]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows the removal of CONFIG_INPUT from saa7134, and
helps to create a better Kconfig dependency hierarchy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason for keeping I2C_HW_SAA7134 is to allow setting a
per-device polling interval. Just move this info to the platform
data, allowing drivers to change it per device, where needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cx23885/cx23885-video.c, cx88/cx88-video.c, davinci/vpif_capture.c, and
davinci/vpif_display.c, group the aligned code into a single if branch.
In saa7134/saa7134-video.c, outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some time a go our customers wrote me about problem with our TV card
BeholdTV Columbus. It's PCMCIA TV card for notebook.
As I understand v4l has some regression with autodetect address of tuners.
I can set incorrect I2C address and had report about detect tuner. No any TV of course.
When I set correct tuner type and I2C address of the tuners all works well.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_dmabuf and videobuf_vmalloc_memory fields have a vmalloc
field to store the kernel virtual address of vmalloc'ed buffers. Rename
the field to vaddr.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of creating dirty wrappers around videobuf_dma_map/unmap that
create a dummy videobuf_queue structure, modify videobuf_dma_map/unmap
to take a device pointer argument and use it directly. The
videobuf_sg_dma_map/unmap then become unused and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem is that dprintk() dereferences "dev" which is null here.
The i2cdprintk() uses "ir" so that's OK.
Also Jean Delvare pointed out a typo in the comment so we may as well
fix that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code had two break statements in a row.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for one more remote control type for Avermedia
M135A (model RM-K6), shipped with Positivo machines.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for Avermedia M733A. The original version for
linux 2.6.31 was sent to me from Avermedia, original author is unknown.
I ported it to current kernels, expanded and fixed key code handling for
RM-K6 remote control, and added an additional pci id also supported.
[mchehab@redhat.com: make checkpatch.pl happier]
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_prio_init/open/close returned an int when in fact they would
always return 0. Make these void functions.
v4l2_prio_close and v4l2_prio_check pass an enum v4l2_priority as a
pointer for no good reason. Replace with a normal enum v4l2_priority
argument.
These changes will simplify the work of moving priority handling into
the v4l core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hybrid tuner FMD1216MEX_MK3 after cold start has disabled IF. This
tuner has internal I2C switch. This switch switch I2C bus between DVB-T
and IF part. Default state is DVB-T. When module saa7134 is load it
can't find IF tda9887 and disable analog TV mode.
Sets internal I2C switch of the tuner to IF by send special value to the
tuner as for receive analog TV from low band. It can be usefule for
other cards.
I didn't set configure a tuner by a tuner model because this tuner can
have different I2C address. May be we can do it later after discuss for
more robust support a tuners.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit bc52d6eb44.
On newer kernels, a saa7134 board stopped to display TV video output
properly. After a bisect, I found it as the commit causing the issue.
Turns out that v4l_bound_align_image isn't doing the same bounding
calculation as manually done previously in saa7134_try_fmt_vid_cap.
What isn't equal is the calculation done in clamp align, while
previously it did "f->fmt.pix.width &= ~0x03", clamp_align function
does "Round to nearest aligned value" as stated in the comment, which
yields a different result. If I comment the round calculation in
clamp_align like this: "x = (x /*+ (1 << (align - 1))*/) & mask",
I get it fixed too, because this way the calculation is the same then.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/IR/ir-raw-event.c is currently written with the assumption
that all "raw" hardware will generate events only on state change (i.e.
when a pulse or space starts).
However, some hardware (like mceusb, probably the most popular IR receiver
out there) only generates duration data (and that data is buffered so using
any kind of timing on the data is futile).
Furthermore, using signed int's to represent pulse/space durations is a
well-known approach when writing ir decoders.
With this patch:
- s64 int's are used to represent pulse/space durations in ns
- a workqueue is used to decode the ir protocols outside of interrupt context
- #defines are added to make decoders clearer
- decoder reset is implemented by passing a zero duration to the kfifo queue
and decoders are updated accordingly
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices have in-hardware Remote Controller decoder, while others
need a software decoder to get the IR code. As each software decoder
can be enabled/disabled individually, allowing multiple protocol
decoding capability.
On the other hand, hardware decoders have a limited protocol
support, often being able of decoding just one protocol each time.
So, each type needs a different set of capabilities to control the
supported protocol(s).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Andy Walls <awalls@md.metrocast.net> for pointing me his
code, that gave me some ideas to better implement it.
After some work with saa7134 bits, I found a way to catch both IRQ
edge pulses. By enabling it, the NEC decoder can now take both
pulse and spaces into account, making it more precise.
Instead of the old strategy of handling the events all at once,
this code implements a state machine. Due to that, it handles
individual pulse or space events, validating them against the
protocol, producing a much more reliable decoding.
With the new implementation, the protocol trailer bits are properly
handled, making possible for the repeat key to work.
Also, the code is now capable of handling both NEC and NEC extended
IR devices. With NEC, it produces a 16 bits code, while with NEC
extended, a 24 bits code is returned.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code that enables IRQ for the Remote Controller on saa7134 is a little
messy: it is outside saa7134-input, it checks if RC is GPIO based, and
it mixes both serial raw decode with parallel reads from a hardware-based
IR decoder.
Also, currently, it doesn't allow to trigger both transition edges at GPIO16
and GPIO18 lines. A rework on the code is needed to provide a better way
to specify what saa7134-input needs, maybe even moving part of the code from
saa7134-core and saa7134-cards into saa7134-input.
Yet, as a large rework is happening at RC core, it is better to wait until
the core changes stablize, in order to rework saa7134 RC internals.While
this don't happen, let's just change the logic a little bit to allow
enabling IRQ to be generated on both edge transitions, in order to better
support pulse/space raw decoders.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's an error at the IRQ2 bit map registers. Also, it doesn't
show what bits are needed for positive and for negative edge.
In the case of IR raw decoding, for some protocols, it is important
to detect both positive and negative edges. So, a latter patch
will need to use the other values.
Also, the code that detects problems on IRQ handling is incomplete,
as it disables only one of the IRQ bits for GPIO16 and GPIO18.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the ugly keymap sequences, use the new rc-*.ko keymap
files. For now, it is still needed to have one keymap loaded, for the
RC code to work. Later patches will remove this depenency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A latter patch will reuse the ir_input_register with a different meaning.
Before it, change all occurrences to a temporary name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaces most of the occurences of IR keytables on V4L drivers by a macro
that evaluates to provide the name of the exported symbol.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Especially when IR needs to do polling, it generates lots of wakeups per
second. This makes no sense, if the input event device is closed.
Adds a callback handler to the IR hardware driver, to allow registering
an open/close ops.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some decoders and a lirc_dev interface may need some other operations to work.
For example: IR device register/unregister and ir_keydown events may need to
be tracked.
As some operations can occur in interrupt time, and a lock is needed to prevent
un-registering a decode while decoding a key, the lock needed to be convert
into a spin lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At raw_decode mode, the key is processed after the end of a timer. The
previous code resets the timer every time something is received at the IR
port. While this works fine with IR's that don't implement repeat, like
Avermedia RM-JX IR, it keeps waiting until keydown, on IR's that implement
NEC repeat command, like the Terratec yellow.
The solution is to change the behaviour to do the timeout after the first
received data.
The timeout is currently set to 15 ms, as it works fine with NEC protcocol.
It may need some adjustments to support other protocols and to better handle
spurious detections that may happen with some IR sensors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a method to pass IR raw pulse/code events into ir-core. This is
needed in order to support LIRC. It also helps to move common code
from the drivers into the core.
In order to allow testing, it implements a simple NEC protocol decoder
at ir-nec-decoder.c file. The logic is about the same used at saa7134
driver that handles Avermedia M135A and Encore FM53 boards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds new capture boards Hawell HW-404M7 and HW-808M7. Those cards have 4
or 8 SAA7130 chips and for the work it only needs initialize registers.
The value of those registers were dumped under Windows using flytest.
But board haven't EEPROM.
For the first chip:
SAA7130 (0x7130, SubVenID:1131, SubDevID:0000, Rev: 01)
I2C slave devices found:
No devices
GPIO pins:
Mode : 0x00389C00
Value: 0x00016C00
Video input: 3
Audio input: Analog Line1
For other chips:
SAA7130 (0x7130, SubVenID:1131, SubDevID:0000, Rev: 01)
I2C slave devices found:
No devices
GPIO pins:
Mode : 0x00389200
Value: 0x00010000
Video input: 3
Audio input: Analog Line1
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In quickcam_messenger.c, if the NULL test on uvd is needed, then the
dereference should be after the NULL test.
In vpif_display.c, std_info is initialized to the address of a structure
field. This seems unlikely to be NULL. Test std_info->stdid instead.
In saa7134-alsa.c, the function is only called from one place, where the
chip argument has already been dereferenced. On the other hand, if it
should be kept, then card should be initialized after it.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some variants of the ASUS TV-FM 7135 are handled as the ASUSTeK P7131
Analog (card=146). However, by the time we find out, some
card-specific initialization is missed. In particular, the fact that
the IR is GPIO-based. Set it when we change the card type, and run
saa7134_input_init1().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, both driver and keytable names are exported to userspace. This
will help userspace to decide when a table need to be replaced
by another one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
