After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
tifm_sd: treat "status error" as normal command completion
mmc: wbsd: Remove stray kunmap_atomic()
mmc: sdhci: Stop asking for mail
mmc: sdhci: Remove driver version
mmc: wbsd: Remove driver version
TI FlasMedia controller attempts to validate command responses and
issues a "status error" if response does not matches its perceived
(by controller) value. As mmc layer does its own validation we can
safely ignore the controller's opinion.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We get enough error reports without having to ask for it.
Remove notices about mailing the development list.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The driver version was only really meaningful when it was an
out-of-tree driver. Now we can use the version of the kernel.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The driver version was only really meaningful when it was an
out-of-tree driver. Now we can use the version of the kernel.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Atmel AT91 and AVR32 processor architectures share many of the same
peripherals. The PDC (Peripheral Data Controller) registers are also
implemented within in a number of the on-chip peripherals (eg, USART,
MMC, SPI, SSC, etc).
In a attempt not to duplicate the register definitions in each
peripheral, or in each architecture, the at91_pdc.h header in
asm-arm/arch-at91 and asm-avr32/arch-at32ap has been replaced with
linux/atmel_pdc.h.
The definitions have also been renamed from AT91_PDC_* to ATMEL_PDC_*,
and the drivers updated accordingly.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since we actively avoid highmem, calling kmap_atomic() instead
of page_address() is effectively only obfuscation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
MMC high-speed, wide bus support and SD high-speed
are functions that aren't critical for correct
operation of the card. As such, they shouldn't mark
the card as bad or dead when there is a failure
activating these features.
This is needed in particular on some really stupid
hardware (e.g. Winbond's) where not all data transfer
commands are supported.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The wbsd hardware is so incredibly brain damaged that it has an internal
list of commands that result in data transfers. The result being that
commands that aren't on this list aren't supported.
Instead of locking up, waiting for a data interrupt that will never come,
we try to fail a bit more gracefully.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Many controllers have an upper limit on the number of blocks that can be
transferred in one request. Allow the host drivers to specify this and make
sure we avoid hitting this limit.
Also change the max_sectors field to avoid confusion. This makes it map
less directly to the block layer limits, but as they didn't apply directly
on MMC cards anyway, this isn't a great loss.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most controllers have an upper limit on the block size. Allow the host
drivers to specify this and make sure we avoid hitting this limit.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch introduces no semantic changes - it is here for estetic purposes.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In order to support correct suspend and resume several changes were needed:
1. Switch from work_struct to tasklet for command handling. When device
suspend is called workqueues are already frozen and can not be used.
2. Separate host initialization code from driver's probe and don't rely
on interrupts for host initialization. This, in turn, addresses two
problems:
a) Resume needs to re-initialize the host, but can not assume that
device interrupts were already re-armed.
b) Previously, probe will return successfully before really knowing
the state of the host, as host interrupts were not armed in time.
Now it uses polling to determine the real host state before returning.
3. Separate termination code from driver's remove. Termination may be caused
by resume, if media changed type or became unavailable during suspend.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The register access order when setting hardware timeout was incorrect and
causing problems (wrong timeout intervals). This is now fixed.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Two changes are introduced to software timeout handler in order to simplify
its management:
1. The implementation is switched from work_struct to timer
2. Previously, software timeout was rearmed with each interrupt. Now,
current request must complete entirely within timeout interval.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Data buffer for PIO transfer used to be mapped in advance with kmap.
Abolish it in favor of on-demand kmap_atomic.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Previously, stop command was issued right after BRS (block received/sent)
event. Stop command completion event could interfere with the card busy
event, causing miscount of the written blocks.
This patch ensures that stop command issued as last action for a
particular command, after DMA sompletion event and written block
count verification.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Thanks to the generous donation of an SDHC card by John Gilmore, and
the surprisingly enlightened decision by the SD Card Association to
publish useful specs, I've been able to bash out support for SDHC. The
changes are not too profound:
i) Add a card flag indicating the card uses block level addressing and
check it in the block driver. As we never took advantage of byte-level
addressing, this simply involves skipping the block -> byte
translation when sending commands.
ii) The layout of the CSD is changed - a set of fields are discarded
to make space for a larger C_SIZE. We did not reference any of the
discarded fields except those related to the C_SIZE.
iii) Read and write timeouts are fixed values and not calculated from
CSD values.
iv) Before invoking SEND_APP_OP_COND, we must invoke the new
SEND_IF_COND to inform the card we support SDHC.
Signed-off-by: Philipl Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for these devices was broken for 2.6.18-rc1 and later by commit
146ad66eac, which added voltage level support.
This restores the previous behaviour for these devices by ensuring that when
the voltage is changed, only one write to set the voltage is performed.
It may be that both writes are needed if the voltage is being changed between
two non-zero values or that it's safe to ensure that only one write is done
if the hardware only supports one voltage; I don't know whether either is the
case nor can I test since I have only the one SD reader (1524:0550), and it
supports just the one voltage.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Change the parent of cards to be a specific host (a class
device), not the physical controller. This is particularly
useful when the hardware has multiple slots, meaning
multiple hosts.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As card_busy was only used to indicate if the host was exclusively
claimed and not really used to identify a particular card, replacing
it with just a boolean makes things a lot more easily understandable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
During development of SDHC support, it was discovered that the definition
for R6 was incorrect. This patch fixes that and patches the drivers that
do switch on the response type.
Signed-off-by: Philip Langdale <philipl@overt.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pavel Pisa <ppisa@pikron.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch is a fix in order to update MMC response types. This modification is
needed to allow SD card support on OMAP platforms.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Yuha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The MMCI driver might end up aborting the initial command and leaving
the data part of the command sequence still in place. Avoid this
problem by ensuring that any data sequence is properly cleared out
when a command completes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linker level tweaks for the AT91 MMC driver:
- fix a wrongly-exported symbol
- move probe() to init section
- move remove() to exit section
When this driver is statically linked, this patch shrinks the driver's
runtime I-space footprint by over 20% (950 bytes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
fix OMAP MMC workqueue in recent workqueue change
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The driver is usable on the newer SAM9 processors so replace all text
references to AT91RM9200 with just AT91.
The controller bug where all the words are byte-swapped is fixed on the
AT91SAM9 processors. The byte-swapping work-around therefore only needs
to be done if cpu_is_at91rm9200().
[Original patch from Wojtek Kaniewski]
The AT91RM9200 and AT91SAM9260 processors support two MMC/SD slots - the
slot which is connected is now passed via the platform_data and the
correct slot selected in the AT91_MCI_SDCR register.
The driver should not be calling at91_set_gpio_output() since the VCC
pin should have already been configured as an output in the
processor/board setup code. The driver should call
at91_set_gpio_value().
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers report an invalid iomem size, but seem to work
correctly anyway. Change our current error to just a warning and
hope it doesn't cause too much problems.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently on SD/MMC card removal the system exhibits the following message (the platform is ARM Versatile):
prev->state: 2 != TASK_RUNNING??
mmcqd/762[CPU#0]: BUG in __schedule at linux-2.6/kernel/sched.c:3826
(akpm: someone tried to fix this, but it's still wrong)
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
A number of small cleanups to the AT91RM9200 MMC driver:
- fix warnings generated by pr_debug().
- prepend "AT91 MMC:" to printk() messages.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch simplifies the AT91RM9200 MMC interrupt handler code so that
it doesn't re-read the Interrupt Status and Interrupt Mask registers
multiple times.
Also defined AT91_MCI_ERRORS instead of using the hard-coded 0xffff0000.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move the global 'mci_clk' variable into the local 'at91mci_host'
structure.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Use the I/O base-address and IRQ passed to the driver via the
platform_device resources instead of using hardcoded values.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The I/O base address is now stored in the 'at91mci_host' structure. We
therefore have to pass this structure to at91_mci_read() and
at91_mci_write().
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
This patch has fixed the following build error abou au1xmmc.
drivers/mmc/au1xmmc.c: In function `au1xmmc_poll_event':
drivers/mmc/au1xmmc.c:835: warning: unused variable `status'
drivers/mmc/au1xmmc.c: At top level:
drivers/mmc/au1xmmc.c:878: error: parse error before "const"
drivers/mmc/au1xmmc.c: In function `au1xmmc_probe':
drivers/mmc/au1xmmc.c:909: error: `au1xmmc_ops' undeclared (first use in this function)
drivers/mmc/au1xmmc.c:909: error: (Each undeclared identifier is reported only once
drivers/mmc/au1xmmc.c:909: error: for each function it appears in.)
drivers/mmc/au1xmmc.c: At top level:
drivers/mmc/au1xmmc.c:659: warning: 'au1xmmc_request' defined but not used
drivers/mmc/au1xmmc.c:719: warning: 'au1xmmc_set_ios' defined but not used
make[2]: *** [drivers/mmc/au1xmmc.o] Error 1
make[1]: *** [drivers/mmc] Error 2
make: *** [drivers] Error 2
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
since commit fcaf71fd51
struct mmc_host does not have a dev field. Retrieve the device with
mmc_dev() instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: correct request error handling
mmc: Flush block queue when removing card
mmc: sdhci high speed support
mmc: Support for high speed SD cards
mmc: Fix mmc_delay() function
mmc: Add support for mmc v4 wide-bus modes
[PATCH] mmc: Add support for mmc v4 high speed mode
trivial change for mmc/Kconfig: MMC_PXA does not mean only PXA255
Make general code cleanups
Add MMC_CAP_{MULTIWRITE,BYTEBLOCK} flags
Platform device error handling cleanup
Move register definitions away from the header file
Change OMAP_MMC_{READ,WRITE} macros to use the host pointer
Replace base with virt_base and phys_base
mmc: constify mmc_host_ops vectors
mmc: remove kernel_thread()
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
Driver core: show drivers in /sys/module/
Documentation/driver-model/platform.txt update/rewrite
Driver core: platform_driver_probe(), can save codespace
driver core: Use klist_remove() in device_move()
driver core: Introduce device_move(): move a device to a new parent.
Driver core: make drivers/base/core.c:setup_parent() static
driver core: Introduce device_find_child().
sysfs: sysfs_write_file() writes zero terminated data
cpu topology: consider sysfs_create_group return value
Driver core: Call platform_notify_remove later
ACPI: Change ACPI to use dev_archdata instead of firmware_data
Driver core: add dev_archdata to struct device
Driver core: convert sound core to use struct device
Driver core: change mem class_devices to be real devices
Driver core: convert fb code to use struct device
Driver core: convert firmware code to use struct device
Driver core: convert mmc code to use struct device
Driver core: convert ppdev code to use struct device
Driver core: convert PPP code to use struct device
Driver core: convert cpuid code to use struct device
...
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to jump to the part of just flushing the request
when we cannot claim the bus. Sending commands to a bus
we do not own will give unpredictable results.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
After mmc_block's remove function has exited, we must not
touch the card structure in any way. This means we not only
must remove the gendisk, we must also flush out any
remaning requests already queued up.
We previously removed the disk, but didn't flush it,
causing oops:es when removing a card in the middle of a
transfer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The SDHCI spec implies that is is incorrect to set a clock
frequency above 25 MHz without setting the high speed bit.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Modern SD cards support a clock speed of 50 MHz. Make sure we test for
this capability and do the song and dance required to activate it.
Activating high speed support actually modifies the TRAN_SPEED field
of the CSD. But as the spec says that the cards must report 50 MHz,
we might as well skip re-reading the CSD.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Several fixes for mmc_delay():
* Repair if-clause that was supposed to detect sub-hz delays.
* Change yield() to cond_resched() as yield() no longer has the
semantics we desire.
* mmc_delay() is used to guarantee protocol delays, so we cannot
return early (i.e. use _interruptable).
Based on patch by Amol Lad.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This change adds support for the mmc4 4-bit wide-bus mode.
The mmc4 spec defines 8-bit and 4-bit transfer modes. As we do not support
any 8-bit hardware, this patch only adds support for the 4-bit mode, but
it can easily be built upon when the time comes.
The 4-bit mode is electrically compatible with SD's 4-bit mode but the
procedure for turning it on is different. This patch implements only
the essential parts of the procedure as defined by the spec. Two additional
steps are recommended but not compulsory. I am documenting them here so
that there's a record.
1) A bus-test mechanism is implemented using dedicated mmc commands which allow
for testing the functionality of the data bus at the electrical level. This is
pretty paranoid and they way the commands work is not compatible with the mmc
subsystem (they don't set valid CRC values).
2) MMC v4 cards can indicate they would like to draw more than the default
amount of current in wide-bus modes. We currently will never switch the card
into a higher draw mode. Supposedly, allowing the card to draw more current
will let it perform better, but the specs seem to indicate that the card will
function correctly without the mode change. Empirical testing supports this
interpretation.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds support for the high-speed modes defined by mmc v4
(assuming the host controller is up to it). On a TI sdhci controller,
it improves read speed from 1.3MBps to 2.3MBps. The TI controller can
only go up to 24MHz, but everything helps. Another person has taken
this basic patch and used it on a Nokia 770 to get a bigger boost
because that controller can run at 48MHZ.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
PXA MMC driver supports not only PXA255 but also PXA250 and newer ones
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch is part of Juha Yrjola's and Komal Shah's earlier patch to
make general code cleanups
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Komal Shah <komal_shah802003 <at> yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch is part of Tony Lindgren's earlier patch to add
MMC_CAP_{MULTIWRITE,BYTEBLOCK} flags in omap.c
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Tony Lindgren <tony <at> atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch is part of Juha Yrjola's earlier patch to add platform device
error handling and a BUG_ON to verify if host == NULL
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch is part of Juha Yrjola's earlier patch to move register
definitions away from the header file and the header file is removed.
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch is part of Juha Yrjola's earlier patch to change
OMAP_MMC_{READ,WRITE} macros to use the host pointer
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch is part of Juha Yrjola's earlier patch to replace base
with virt_base and phys_base
Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar <at> indt.org.br>
Signed-off-by: Juha Yrjola <juha.yrjola <at> solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now that mmc_host_ops can be constified, update the various drivers
to constify those method tables and shrink the writable data segment.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Replace kernel_thread() with kthread_run()/kthread_stop().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
A number of configuration file changes.
These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't
need to mention every specific AT91 processor explicitly.
Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch converts a if () BUG(); construct to BUG_ON();
which occupies less space, uses unlikely and is safer when
BUG() is disabled.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The card might go to inactive state (according to specification), if
there are unsupported bits set in the OCR.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some broken cards seem to process CMD1 even in stand-by state. The result is
that the card replies with ILLEGAL_COMMAND error for the next command sent
after rescanning. Currently the next command is select card, which would
return the error. But CMD7 does actually succeed and retries of the command
will timeout. The workaround is to poll card status after CMD1 to clear the
pending error.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
SD cards extend the protocol by allowing the host to query a card how many
blocks were successfully stored on the medium. This allows us to safely write
chunks of blocks at once.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Use the new multi block-write error reporting flag and properly tell the block
layer how much data was transferred before the error.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The MMC layer uses the standard work queue for doing card detection. As this
queue is shared with other crucial subsystems, the effects of a long (and
perhaps buggy) detection can cause the system to be unusable. E.g. the
keyboard stops working while the detection routine is running.
The solution is to add a specific mmc work queue to run the detection code in.
This is similar to how other subsystems handle detection (a full kernel
thread is the most common theme).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some Ricoh controllers only respect a full reset when there is no card in the
slot. As we wait for the reset to complete, we must avoid even requesting
those resets on the buggy controllers.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sprinkle some mmiowb() where needed (writeX() before unlock()).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Cc: Daniel Qarras <dqarras@yahoo.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver for TI Flash Media card reader. At present, only MMC/SD cards are
supported.
[akpm@osdl.org: cleanups, build fixes]
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Cc: Daniel Qarras <dqarras@yahoo.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clarify my (Pierre's) position on which GPL versions apply. The patch only
touches the source files where I am the only major author. The people who
have made the minor commits to the files have been contacted and have no
issues with this change.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-mmc:
[MMC] Don't check READY_FOR_DATA when reading
[MMC] MMC_CAP_BYTEBLOCK flag for non-log2 block sizes capable hosts
[MMC] Add multi block-write capability
[MMC] Remove data->blksz_bits member
[MMC] Convert mmci to use data->blksz rather than data->blksz_bits
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The third argument of au1xxx_dbdma_chan_alloc's callback function is not
used anywhere.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no point checking to see if the card is ready to accept
data when we're reading from it - sending the command only wastes
precious bus bandwidth.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some MMC hosts can only handle log2 block sizes. Unfortunately,
the MMC password support needs to be able to send non-log2 block
sizes. Provide a capability so that the MMC password support can
decide whether it should use this support or not.
The unfortunate side effect of this host limitation is that any
MMC card protected by a password which is not a log2 block size
can not be accessed on a host which only allows a log2 block size.
This change just adds the flag. The MMC password support code
needs updating to use it (if and when it is finally submitted.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a capability flag for drivers to set when they can perform multi-
block transfers to cards _and_ correctly report the number of bytes
transferred should an error occur.
The last point is very important - if a driver reports more bytes than
were actually accepted by the card and an error occurs, there is the
possibility for data loss.
Pierre Ossman provided the patch for wbsd and sdhci.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both MMC and SD specifications specify (although a bit unclearly in
the MMC case) that a sector size of 512 bytes must always be
supported by the card.
Cards can report larger "native" size than this, and cards >= 2 GB
even must do so. Most other readers use 512 bytes even for these
cards. We should do the same to be compatible.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having two places which independently calculate the
timeout for data transfers, make it a library function instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Patch from Pavel Pisa
This is another approach to SDHC deficiency workaround.
It seems, that previous solution based on 16 bytes (FIFO length size)
read is still timing sensitive on genirq and fully preemptive kernels.
The new solution is backuped by M9328 UM statement, that only 512 byte
block are working properly and by 2.4.26 FreeScale's SDHC code.
Jay Monkman reports significant improvement on code based
on this driver after applying this change on MX21 as well.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Secure Digital cards use a different algorithm to calculate the timeout
for data transfers. Using the MMC one works often, but not always.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Another misuse of the global 'io' variable instead of the local 'base'.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There were some confusion about base I/O variables in the wbsd driver.
Seems like things have been working on shear luck so far. The global 'io'
variable (used when manually configuring the resources) was used instead of
the local 'base' variable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Juha [l
When the block queue is plugged, mq->req must be set to NULL.
Otherwise mq->req might be left non-NULL, even though mmcqd is
not processing a request, thus preventing the MMC queue thread from
being woken up when new requests do arrive.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
O2 Micro's controllers have a larger specification version value and are
therefore denied by the driver. When bypassing this check they seem to work
fine. This patch makes the code a bit more forgiving by changing the error
to a warning.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There was a writel() being used on a 16-bit register.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
lockdep needs to have the waitqueue lock initialized for on-stack
waitqueues implicitly initialized by DECLARE_COMPLETION().
Annotate mmc_wait_for_req()'s on-stack completion accordingly.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 3541/2: workaround for PXA27x erratum E7
[ARM] nommu: provide a way for correct control register value selection
[ARM] 3705/1: add supersection support to ioremap()
[ARM] 3707/1: iwmmxt: use the generic thread notifier infrastructure
[ARM] 3706/2: ep93xx: add cirrus logic edb9315a support
[ARM] 3704/1: format IOP Kconfig with tabs, create more consistency
[ARM] 3703/1: Add help description for ARCH_EP80219
[ARM] 3678/1: MMC: Make OMAP MMC work
[ARM] 3677/1: OMAP: Update H2 defconfig
[ARM] 3676/1: ARM: OMAP: Fix dmtimers and timer32k to compile on OMAP1
[ARM] Add section support to ioremap
[ARM] Fix sa11x0 SDRAM selection
[ARM] Set bit 4 on section mappings correctly depending on CPU
[ARM] 3666/1: TRIZEPS4 [1/5] core
ARM: OMAP: Multiplexing for 24xx GPMC wait pin monitoring
ARM: OMAP: Fix SRAM to use MT_MEMORY instead of MT_DEVICE
ARM: OMAP: Update dmtimers
ARM: OMAP: Make clock variables static
ARM: OMAP: Fix GPMC compilation when DEBUG is defined
ARM: OMAP: Mux updates for external DMA and GPIO
...
When there is remaining blocks untransferred, we get two error messages saying
almost the same thing. Make sure at most one is shown.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some controllers incorrectly report that the cannot do DMA. Forcefully enable
it for those that we know it works fine on.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some controllers fail to complete a reset unless you touch the clock register
first.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
New version number for sdhci driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As some specific controllers will have bugs, we need a way to map special
behaviour to certain hardware.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Properly test for controller interface to see if it's DMA capable. As many
controllers are misconfigured in this regard, also add debug parameters to
force DMA support either way.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification states that the capabilities register might need a reset to
get correct values after boot up.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check the interface version of the controller and bail out if it's an unknown
version.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conform to the sdhci specification as to which inhibit bits should be checked
at different times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The controller has an upper limit on the block size. Make sure we do not
cross it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers will issue an interrupt when a configurable number of
bytes have been transfered using DMA. The purpose is to handle multiple,
scattered memory pages.
Unfortunately, it requires that all transfers are completely aligned to
memory pages, which we cannot guarantee. So we just disable the function.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers operate with blocks, not bytes. The PIO routines must
therefore make sure that the minimum unit transfered is a complete block.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification says that interrupts should be cleared before the source is
removed. We should also not set unknown bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci specification states that some registers must be written to in a
specific order.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the give timeout clock and calculate a proper timeout instead of using the
maximum at all times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The reset register is automatically cleared when the reset has completed.
Hence, we should busy wait and not have a fixed delay.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current timeout loop assume that jiffies are updated. This might not be
the case depending on locks and if the kernel is compiled without preemption.
Change the system to use a counter and fixed delays.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers can support up to three voltage levels. Detect which
and report back to the MMC layer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As sdhci is a generic driver, it is helpful to see some more specific
identification of the actual hardware in dmesg. PCI vendor, device and
revision is sufficient in most cases.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A base clock value of 0 means that the driver must get the base clock through
some other means. As we have no other way of getting it, we must abort.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch makes OMAP MMC work again:
- Fix compile errors
- Do not ioremap base as it is already statically mapped
- Clean-up platform device handling
- Fix compile warnings
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Andrew Victor
This patch includes code cleanups and minor fixes to the AT91RM9200 MMC
driver.
1. Replace calls to DBG() with pr_debug().
2. 'host' can never be null, so don't bother checking for that case.
3. Remove SA_SAMPLE_RANDOM from request_irq(). [Patch from Matt
Mackall]
4. clk_get() doesn't return NULL on error - need to test returned value
with IS_ERR().
5. Free resources if clk_get() or request_irq() fails.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMC specification allows non-power of two block sizes. As such,
we should not pass the log2 block size to host drivers, but instead
pass the byte size.
However, ARM MMCI can only work with log2 block size, so continue to
pass both the log2 block size and byte block size. This means that
for the moment, the byte block size must remain a power of two, but
this is the first stage of removing this restriction for other hosts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On 64-bit machines, we just lost the uppermost 32 bits.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver is selectable on other than Au1200 Alchemy systems but won't
build nor work - there is no MMC hw.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
md->disk was being used in a debug message before it was allocated.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Pavel Pisa
There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
