Introduce new option CONFIG_BLK_DEV_IDEDMA_SFF for non-PCI SFF-8038i compatible
bus mastering IDE controllers (which there are a few known), thus fixing a hack
made for Palmchip BK3710 controller...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move check_dma_crc() to ide-dma.c and add inline version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Rename check_dma_crc() to ide_check_dma_crc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Delete filenames/versions from comments.
I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s
to maintainers of the respective drivers.
While at it:
* Remove unused VERSION define from ide.c.
* Remove unused/stale DRV_VERSION define from au1xxx-ide.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_build_sglist() and ide_destroy_dmatable() available also when
CONFIG_BLK_DEV_IDEDMA_PCI=n.
* Use ide_build_sglist() and ide_destroy_dmatable() in {ics,au1xxx-}ide.c
and remove no longer needed {ics,au}ide_build_sglist().
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pci_map_sg() -> dma_map_sg() in ide_build_sglist().
* pci_unmap_sg() -> dma_unmap_sg() in ide_destroy_dmatable().
There should be no functionality changes caused by this patch except
for blackfin arch whose dma_[un]map_sg() implementation differs from
pci_[un]map_sg() one (on s390 arch there is no PCI, on avr32 and h8300
archs PCI is currently unsupported, on m32r arch PCI support depends
on BROKEN, on m68k arch PCI support depends on HADES which in turn
depends on BROKEN, on all other archs dma_[un]map_sg() functionality
matches with pci_[un]map_sg() one).
blackfin behavior change was ack-ed by Bryan Wu.
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Keep pointer to struct device instead of struct pci_dev in ide_hwif_t.
While on it:
* Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_destroy_dmatable() in:
* ide-dma.c::ide_build_dmatable()
* sgiioc4.c::sgiioc4_build_dma_table()
* pmac.c::pmac_ide_{build,destroy}_dmatable()
There should be no functionality changes caused by this patch.
v2:
* pmac.c build fix from Andrew Morton.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
do_rw_taskfile() has been fixed to check the return value
of ->dma_setup method so this BUG_ON() is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The TRM-290 chip is *not* SFF-8038i compatible and therefore can *not* call
ide_setup_dma() -- fix this and also cleanup the code a bit...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dma_on can be unexported.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests. Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set. Also,
ide_dma_intr() is modified to use task_end_request().
Enables TASKFILE ioctls to get valid register outputs on
successful completion.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix SWDMA/MWDMA masks in cy82c693_chipset.
* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
check whether the DMA should be enabled even if ide_max_dma_mode()
fails.
* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
and remove no longer needed cy82c693_ide_dma_on(). Then set
IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
cy82c693_chipset.
* Bump driver version.
As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
->ide_dma_on method is called only after successful ide_dma_check() call
(ide_dma_check()->ide_tune_dma() checks DMA blacklist) or if drive->using_dma
has been previously enabled for a given device (->ide_dma_on is the only place
which sets drive->using_dma to '1').
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->dma_off_quietly is always called before ide_set_dma()
so the call can be moved inside ide_set_dma().
* ide_dma_check() doesn't touch hardware so ->dma_off_quietly
call for 'rc == -1' case is redundant, remove it.
* '0' and '-1' are the only values returned by ide_dma_check()
so remove dead code for other cases.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert cmd64x, hpt366 and pdc202xx_old host drivers to use
pci_resource_start(hwif->pci_dev, 4) instead of hwif->dma_master.
* Remove no longer needed ->dma_master field from ide_hwif_t.
v2:
* Use the more readable 'hwif->dma_base - (hwif->channel * 8)' instead of
pci_resource_start(hwif->pci_dev, 4).
v3:
* Use hwif->extra_base in hpt366/pdc20xx_old + some cosmetic fixups over v2
(suggested by Sergei).
v4:
* Correct offsets in hpt3xxn_set_clock().
v5:
* Use hwif->extra_base in hpt366 for _real_ this time. (Noticed by Sergei)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_xfer_verbose() fixups:
- beautify returned mode names
- fix PIO5 reporting
- make it return 'const char *'
* Change printk() level from KERN_DEBUG to KERN_INFO in ide_find_dma_mode().
* Add ide_id_dma_bug() helper based on ide_dma_verbose() to check for invalid
DMA info in identify block.
* Use ide_id_dma_bug() in ide_tune_dma() and ide_driveid_update().
As a result DMA won't be tuned or will be disabled after tuning if device
reports inconsistent info about enabled DMA mode (ide_dma_verbose() does the
same checks while the IDE device is probed by ide-{cd,disk} device driver).
* Remove no longer needed ide_dma_verbose().
This patch should fix the following problem with out-of-sync IDE messages
reported by Nick Warne:
hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache<7>hdd:
skipping word 93 validity check
, UDMA(66)
and later debugged by Mark Lord to be caused by:
ide_dma_verbose()
printk( ... "2048kB Cache");
eighty_ninty_three()
printk(KERN_DEBUG "%s: skipping word 93 validity check\n");
ide_dma_verbose()
printk(", UDMA(66)"
Please note that as a result ide-{cd,disk} device drivers won't report the
DMA speed used but this is intended since now DMA mode being used is always
reported by IDE core code.
v2:
* fixes suggested by Randy:
- use KERN_CONT for printk()-s in ide-{cd,disk}.c
- don't remove argument name from ide_xfer_verbose() declaration
v3:
* Remove incorrect check for (id->field_valid & 1) from ide_id_dma_bug()
(spotted by Sergei).
* "XFER SLOW" -> "PIO SLOW" in ide_xfer_verbose() (suggested by Sergei).
* Fix ide_find_dma_mode() to report the correct mode ('mode' after being
limited by 'req_mode').
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Nick Warne <nick@ukfsn.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on the report from snowbat@gmail.com.
Fixes kernel bugzilla bug #9195.
Tested-by: snowbat@gmail.com
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 33c1002ed9 incorrectly changed return
value from '0' to '-1', fix it (ns87415 was the only host driver affected
since it uses both IDE_HFLAG_TRUST_BIOS_FOR_DMA and IDE_HFLAG_NO_ATAPI_DMA).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set hwif->dma_base only if allocation of extra ports succeeds.
While at it:
* Move setting of hwif->dma_{base,master} from ide_{mapped_mmio,iomio}_dma()
to ide_setup_dma().
* Rename 'dma_base' argument to 'base' in ide_setup_dma() (to make the code
obey 80-columns limit and increase its readability).
* Remove stale ide_setup_dma() comment.
v2:
* Change to allocate hwif->dmatable_cpu before reserving I/O ports missed
teardown code (spotted by Sergei). On the second thought this change is
actually unnecessary so revert it in v2.
* Make ide_release_dma_engine() void and remove needless comment.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "hdx=nodma" option allowing user to disallow DMA for a given device.
* Obsolete "ide=nodma" option.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "good DMA drives" hack for icside to ide-dma.c::ide_find_dma_mode()
(in the long-term it should be either removed or generalized for all hosts).
* Use ide_tune_dma() in icside.c::icside_dma_check().
This results in the following changes in behavior:
- pre-EIDE SWDMA modes are now also respected
- drive->autodma is checked instead of hwif->autodma
(doesn't really matter as icside sets both to "1")
* Make ide-dma.c::__ide_dma_good_drive() static and drop "__" prefix.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add an extra argument to ide_max_dma_mode() for passing requested transfer
mode. Use it as an upper limit when finding the best DMA for device/host.
* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
ide_find_dma_mode(). Also add inline ide_find_dma_mode() version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
to avoid false warning from eighty_ninty_three().
* Use ide_find_dma_mode() to limit the user requested transfer mode in
ide_rate_filter(). Also limit the requested mode by host max PIO mode.
Above changes make ide_rate_filter() to:
* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
and 0x25-0x39, values > 0x46 were already clipped down, same for values
0x25-0x39 but iff UDMA was not supported by the host).
* Clip desired transfer mode down if it is currently unsupported by IDE core
(PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
not supported by the host).
* Clip desired transfer mode down according to the host capabilities
(UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
also ->atapi_dma flag was not respected).
* Clip desired transfer mode down according to the device capabilities
(except PIO modes for now which require mode work) - shouldn't be a
problem since ide_set_xfer_rate() is called _after_ device has accepted
given transfer mode.
and also result in a number of host driver specific bugfixes:
* icside
- clip unsupported PIO5 mode down
- fix unsupported/invalid modes being set in drive->current_speed
* ide-cris
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix BUG() on unsupported/invalid modes
* au1xxx-ide
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
(if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down
* aec62xx
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix 0x00 being programmed as PIO timing for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* alim15x3
- clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
- fix theoretical OOPS for 0x0F mode
- fix unsupported/invalid modes being set on the device
* amd74xx
- clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* atiixp
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix cached MWDMA mode being cleared for unsupported/invalid modes
- fix PIO{0,2} timings being programmed for unsupported/invalid modes
- fix theoretical OOPS for PIO5-6 and 0x0F modes
- fix unsupported/invalid modes being set on the device
* cmd64x
- clip unsupported SWDMA0-2 modes down
* cs5530
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* cs5535
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix theoretical OOPS for PIO5-6 and 0x0F modes
* hpt34x
- clip DMA modes down for ATAPI devices
- fix invalid timings being programmed for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* hpt366
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for unsupported/invalid modes
- fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* it8213
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* it821x
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
(chipset in smart mode and revision 0x10 in pass-through mode)
* jmicron
- clip unsupported SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_new
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_old
- clip unsupported PIO5 mode down
- fix incorrect timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* piix
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* sc1200
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* scc_pata
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down
* serverworks
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* siimage
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices (SATA chipsets)
* sis5513
- clip unsupported PIO5 mode down
- fix BUG() on unsupported/invalid modes
* sl82c105
- clip unsupported SWDMA0-2 modes down
* slc90e66
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* tc86c001
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
- fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* triflex
- clip unsupported PIO5 mode down
* via82cxxx
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* pmac
- clip unsupported PIO5 and SWDMA0-2 modes down
* cmd640/ht6560b
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)
* opti621
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)
While at it:
* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().
* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Give the udma_filter() method call precedence over using the mode masks.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the MWDMA modes (at least that could be seen in their so-called drivers :-),
so the driver needs to account for this -- to achieve this:
- add mdma_filter() method from the original patch by Bartlomiej Zolnierkiewicz
with his consent;
- install the method for all chips to only return empty mask if a SATA drive
is detected on HPT372{AN]/374 chips...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.
* Add ivb_list[] table for listening early UDMA66 devices which don't conform
to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
and use only device side cable detection for them since host side cable
detection may be unreliable.
* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
(from Craig's bugreport).
v2:
* Improve kernel message basing on suggestion from Sergei.
v3:
* Don't print kernel message when no device side cable detection is done,
plus some minor fixes. (Noticed by Sergei)
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DMA blacklist checking (->ide_dma_on check probably can go now).
* Add ->atapi_dma flag checking and remove no longer needed
ns87415_ide_dma_check() from ns87415 host driver.
* Remove now needless __ide_dma_check() wrapper and symbol export.
* Check drive->autodma instead of hwif->autodma (there should be no changes in
behavior as all users of config_drive_for_dma() set both ->autodma flags).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This removes the support to treat "ALL" as a wildcard for
firmware revision. This is made a separate patch, as it will
break out-of-tree ide drivers that feed its own table that uses
"ALL" as the wildcard to ide_in_drive_list().
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Earlier, the matching of (model,rev) in ide-dma black/white list
handling was to consider "ALL" in the table to match any
revision. This makes NULL to be also an accepted wildcard, and
changes the entries of tables in ide-dma.c to use NULL.
The code still accepts "ALL" as the wildcard, in order to keep
any out-of-tree ide driver that feeds its own table that uses
"ALL" as the wildcard to ide_in_drive_list() function from
breaking.
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_dma_timeout() method's result is discarded, make it return 'void'.
While at it, drop 'ide_' from the method's name, drop the '__' prefix from
the default method's name, and do some cleanups in this method driver-wise:
- in ide-dma.c, au1xxx-ide.c, and pdc202xx_old.c, define/use 'hwif' variable;
- in au1xxx-ide.c, get rid of commented out printk();
- in sl82c105.c, get rid of unnecessary variables.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_dma_lostirq() method's result is discarded, make it return 'void'.
While at it, rename the method to dma_lost_irq(), drop the '__' prefix from the
default method's name, and do some cleanups in this method driver-wise:
- in aec62xx.c, rename the method in accordance with other drivers, and get rid
of unnecessary variables there;
- in pdc202xx_old.c, define/use 'hwif' variable;
- in sgiioc4.c, rearrange the code to call the resetproc() method directly.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There are a few entries in ata_device_blacklist[] in libata-core.c
marked with HORKAGE_NODMA but are missing from drive_blacklist[]
in ide-dma.c. This patch makes the lists in sync.
Also remove a duplicated entry for "SanDisk SDP3B-64".
Signed-off-by: Junio C Hamano <junkio@cox.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
