. add support for the M5235EVB board
. add support for the SOM5282 board
. add support for the MOD5272 board
. fix end of memory define for eLITE board
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use the THREAD_SIZE define when manipulating the stack instead of
hard coded values (for the 68328 and 68360 sub-architectures).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New architecture and board configuration support for m68knommu.
. add 523x ColdFire support
. add support for SOM5282 and MOD5272 boards
. break up the 527x to be separate 5271 and 5275. There is some
subtle differences that (like RAM config) that need to be dealt with
. add option to support selecting 4k kernel stack
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the 523x ColdFire family of processors
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make show_stack() consistent with other architectures.
Put the vector string names in the .rodata section.
Patch originally submitted by Philippe De Muyter <phdm@macqel.be>.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correctly determine the end of ram for ram setups that do not
start at base address of 0. Add support for the MOD5272 board,
which doesn not have a ram base of 0.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
. setup for the new 523x ColdFire family
. break up of 527x to be 5271 and 5275
. some white space cleanup
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We weren't explicitly setting the page table bits we desired
in user_prot in the protection table, which resulted in the
user mappings for v6 CPUs being marked global.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We run into problems if we blindly enable L2 prefetching without
checking that the L2 cache is actually enabled. Additionaly, if we
disable the L2 cache we need to ensure that we disable L2 prefetching.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In adjusting the logic for SLB miss for the dynamic hugepage stuff, I
messed up the !CONFIG_HUGETLB_PAGE case, failing to set the SLB flags
properly.
This fixes it. It also streamlines the logic for the HUGETLB_PAGE case
(removing a couple of branches) while we're at it.
Booted, and roughly tested on POWER5 (with and without HUGETLB_PAGE),
iSeries/RS64 (no hugepage available), and G5 (with and without
HUGETLB_PAGE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No point checking what CPU architecture level we have each time
within the loop, so precompute the base PMD flags outside the
loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The prototype for sys_fadvise64_64() is:
long sys_fadvise64_64(int fd, loff_t offset, loff_t len, int advice)
The argument list is therefore as follows on legacy ABI:
fd: type int (r0)
offset: type long long (r1-r2)
len: type long long (r3-sp[0])
advice: type int (sp[4])
With EABI this becomes:
fd: type int (r0)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
advice: type int (sp[8])
Not only do we have ABI differences here, but the EABI version requires
one additional word on the syscall stack.
To avoid the ABI mismatch and the extra stack space required with EABI
this syscall is now defined with a different argument ordering
on ARM as follows:
long sys_arm_fadvise64_64(int fd, int advice, loff_t offset, loff_t len)
This gives us the following ABI independent argument distribution:
fd: type int (r0)
advice: type int (r1)
offset: type long long (r2-r3)
len: type long long (sp[0]-sp[4])
Now, since the syscall entry code takes care of 5 registers only by
default including the store of r4 to the stack, we need a wrapper to
store r5 to the stack as well. Because that wrapper was missing and was
always required this means that sys_fadvise64_64 never worked on ARM and
therefore we can safely reuse its syscall number for our new
sys_arm_fadvise64_64 interface.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This kills warnings when building drivers/ide/ide-iops.c
and puts us in-line with what other platforms do here.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change sn2-specific calls into generic functions. Without this change
the uncached allocator will not work on non-sn2 platforms.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Catalin Marinas
Minor compilation error fix.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Steve Longerbeam
Adds an implementation of unaligned LDRD and STRD fixups.
Also fixes a bug where do_alignment() would misinterpret and
fixup an unaligned LDRD/STRD as LDRH/STRH, causing memory
corruption.
This is the same as Patch #2867/1, but with minor whitespace
and comments changes, plus a check for arch-level >= v5TE
before printing ai_dword count in proc_alignment_read().
Signed-off-by: Steve Longerbeam <stevel@mwwireless.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
timer_dyn_reprogram() fails with an OOPS if the
configuration for CONFIG_NO_IDLE_HZ is enabled, and
the system has no support for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The following patch fixes two warnings in arch/ppc/syslib/m8xx_setup.c
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I had some time to think about PCI assign issues in 2.6.13-rc series.
The major problem here is that we call pci_assign_unassigned_resources()
way too early - at subsys_initcall level. Therefore we give no chances
to ACPI and PnP routines (called at fs_initcall level) to reserve their
respective resources properly, as the comments in drivers/pnp/system.c
and drivers/acpi/motherboard.c suggest:
/**
* Reserve motherboard resources after PCI claim BARs,
* but before PCI assign resources for uninitialized PCI devices
*/
So I moved the pci_assign_unassigned_resources() call to
pcibios_assign_resources() (fs_initcall), which should hopefully fix a
lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary.
Other changes:
- remove resource assignment code from pcibios_assign_resources(), since
it duplicates pci_assign_unassigned_resources() functionality and
actually does nothing in 2.6.13;
- modify ROM assignment code as per Ben's suggestion: try to use firmware
settings by default (if PCI_ASSIGN_ROMS is not set);
- set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for
various setups.
Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with
the 4kB CardBus IO size previously).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can put the __softirq_pending mask in the cpudata,
no need for the silly NR_CPUS array in kernel/softirq.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The {BEGIN,END}_FTR_SECTION asm macros used in ppc64 to nop out
sections of code at runtime cannot be nested. However, we do nest
them in hash_low.S. We get away with it there, because there is
nothing between the BEGIN markers for each section. However, that's
confusing to someone reading the code.
This patch removes the nested ifset and ifclr feature sections,
replacing them with a single feature section in the full mask/value
form.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a rare memory leak found by Coverity.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While ppc64 has the CONFIG_HZ Kconfig option, it wasnt actually being
used. Connect it up and set all platforms to 250Hz.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's the 970MP's PVR (processor version register) entry for oprofile.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some RS64-based machines (p620, F80, others) have problems with firmware
returning 0xdeadbeef instead of failure to allocations that end at the
1GB mark.
We have two options:
1. Detect the undocumented 0xdeadbeef return value and interpret it as
a failure.
2. Avoid allocating that high.
(2) is really the cleaner solution here. 768MB is plenty of room so use
that as the max alloc_top instead of 1GB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc and ppc64 trees are hopefully going to merge over time, so this
patch begins the process by creating a place for the merging of the
header files.
Create include/asm-powerpc (and move linkage.h into it from
asm-{ppc,ppc64} since we don't like empty directories). Modify the
ppc and ppc64 Makefiles to cope.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Create vio_bus_ops so that we just pass a structure to vio_bus_init
instead of three separate function pointers.
Rearrange vio.h to avoid forward references. vio.h only needs
struct device_node from prom.h so remove the include and just
declare it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Take some assignments out of vio_register_device_common and
rename it to vio_register_device.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Formatting changes to vio.c to bring it closer to the
kernel coding standard.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
gcc 3.4 (at least the build we are using) puts the gcc generated .ident
string into a .note section at the end of the files it compiles (gcc
3.3.3-hammer and gcc 4.0.2 Debian puts it in the .text section). This
means that the lparmap.s file we produce in the iSeries build may end with
a .note section. When we include it into head.S, the assembler can no
longer resolve some of the conditional branches since the target label
ends up too far away. This patch just forces us back to the .text section
after including lparmap.s.
The breakage was caused by my patch "iSeries build with newer assemblers
and compilers" (sha1-id: 2ad5649662).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A mistake rebasing the series of ppc64 head.S cleanup patches meant
the #include of lparmap.s, needed for iSeries was lost. This patch
puts it back again.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Deepak Saxena
Working on adding support for 36-bit static mappings for ARMv6 and
Intel's XSC3 core and noticed that alloc_init_supersection currently
increments the phys addr by 1MB on each of the 16 iterations and then
forces alignment to supersection size (16MB). This is really uneeded
b/c we have already forced the phys address to be 16MB aligned in
create_mapping(). Furthermore, this breaks 36-bit addressing b/c bits
[23:20] of the PMD contain bits [35:32] of the physical address and
the masking causes us to loose those bits thus ending up with an
incorrect virt -> phys translation. The other option is to have an
alloc_init_supersection36.
Tested on Intel IXP2350 CPU with 36-bit static I/O mappings.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Show the state of DVS (Dynamic Voltage Scaling) when
starting up on the S3C2440
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add the definitions for the S3C2410_CLKSLOW registers to
the header files, and show the values when the system
starts up
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch implements the set_irq_type() hooks for configuring GPIO
IRQ type and updates all the platforms to use it instead of the
gpio_line_config() function which is now used to configure input
vs. output on the pins.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
None of the board-specific map_io routines do anything, so kill them.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It appears that a memory barrier soon after a mispredicted
branch, not just in the delay slot, can cause the hang
condition of this cpu errata.
So move them out-of-line, and explicitly put them into
a "branch always, predict taken" delay slot which should
fully kill this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the spinlock routines were moved out of line into
kernel/spinlock.c this made it so that the debugging
spinlocks record lock acquisition program counts in the
kernel/spinlock.c functions not in their callers.
This makes the debugging info kind of useless.
So record the correct caller's program counter and
now this feature is useful once more.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed sparc architecture specific users of asm/segment.h and
asm-sparc/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed sparc64 architecture specific users of asm/segment.h and
asm-sparc64/segment.h itself
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current uncorrectable error handling was poor enough
that the processor could just loop taking the same
trap over and over again. Fix things up so that we
at least get a log message and perhaps even some register
state.
In the process, much consolidation became possible,
particularly with the correctable error handler.
Prefix assembler and C function names with "spitfire"
to indicate that these are for Ultra-I/II/IIi/IIe only.
More work is needed to make these routines robust and
featureful to the level of the Ultra-III error handlers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify we really are taking a data access exception trap, at TL1, from
one of the window spill/fill handlers.
Else call a new function, data_access_exception_tl1, to log the error.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Read ASI_IMMU SFSR not ASI_DMMU.
2) IMMU has no SFAR, read TPC instead
3) Delete old and incorrect comment about the DTLB protection
trap having a dependency on the SFSR contents in order to
function correctly
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paulus, I think this is now a reasonable candidate for the post-2.6.13
queue.
Relax address restrictions for hugepages on ppc64
Presently, 64-bit applications on ppc64 may only use hugepages in the
address region from 1-1.5T. Furthermore, if hugepages are enabled in
the kernel config, they may only use hugepages and never normal pages
in this area. This patch relaxes this restriction, allowing any
address to be used with hugepages, but with a 1TB granularity. That
is if you map a hugepage anywhere in the region 1TB-2TB, that entire
area will be reserved exclusively for hugepages for the remainder of
the process's lifetime. This works analagously to hugepages in 32-bit
applications, where hugepages can be mapped anywhere, but with 256MB
(mmu segment) granularity.
This patch applies on top of the four level pagetable patch
(http://patchwork.ozlabs.org/linuxppc64/patch?id=1936).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
You can't call get_property() on a NULL node, so check if of_chosen is set
in check_for_initrd().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/setup.c | 20 ++++++++++++--------
1 files changed, 12 insertions(+), 8 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
unflatten_device_tree() doesn't check if lmb_alloc() succeeds or not, it
should. All it can do is panic, but at least there's an error message
(assuming you have some sort of console at that point).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/prom.c | 9 +++++++--
1 files changed, 7 insertions(+), 2 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
When unflatten_dt_node() fails to find an OF_DT_END_NODE tag it prints
"Weird tag at start of node", this should be "Weird tag at end of node".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
arch/ppc64/kernel/prom.c | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves power4_enable_pmcs() to arch/ppc64/kernel/pmc.c.
I've tested it on P5 LPAR and P4. It does what it used to.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If both CONFIG_XMON and CONFIG_XMON_DEFAULT is enabled in the .config,
there is no way to disable xmon again. setup_system calls first xmon_init,
later parse_early_param. So a new 'xmon=off' cmdline option will do the right
thing.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can now remove CONFIG_MSCHUNKS as it doesn't do anything interesting
anymore.
The only macro in abs_addr.h which is called by non-iSeries code is
phys_to_abs(), so remove the other dummy implementations, and we add a
firmware feature check to phys_to_abs().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
lmb_phys_mem_size() can always return lmb.memory.size, as long as it's called
after lmb_analyze(), which it is. There's no need to recalculate the size on
every call.
lmb_analyze() was calculating a few things we then threw away, so just don't
calculate them to start with.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We no longer need the lmb code to know about abs and phys addresses, so
remove the physbase variable from the lmb_property struct.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
abs_to_phys() is a macro that turns out to do nothing, and also has the
unfortunate property that it's not the inverse of phys_to_abs() on iSeries.
The following is for my benefit as much as everyone else.
With CONFIG_MSCHUNKS enabled, the lmb code is changed such that it keeps
a physbase variable for each lmb region. This is used to take the possibly
discontiguous lmb regions and present them as a contiguous address space
beginning from zero.
In this context each lmb region's base address is its "absolute" base
address, and its physbase is it's "physical" address (from Linux's point of
view). The abs_to_phys() macro does the mapping from "absolute" to "physical".
Note: This is not related to the iSeries mapping of physical to absolute
(ie. Hypervisor) addresses which is maintained with the msChunks structure.
And the msChunks structure is not controlled via CONFIG_MSCHUNKS.
Once upon a time you could compile for non-iSeries with CONFIG_MSCHUNKS
enabled. But these days CONFIG_MSCHUNKS depends on CONFIG_PPC_ISERIES, so
for non-iSeries code abs_to_phys() is a no-op.
On iSeries we always have one lmb region which spans from 0 to
systemcfg->physicalMemorySize (arch/ppc64/kernel/iSeries_setup.c line 383).
This region has a base (ie. absolute) address of 0, and a physbase address
of 0 (as calculated in lmb_analyze() (arch/ppc64/kernel/lmb.c line 144)).
On iSeries, abs_to_phys(aa) is defined as lmb_abs_to_phys(aa), which finds
the lmb region containing aa (and there's only one, ie. 0), and then does:
return lmb.memory.region[0].physbase + (aa - lmb.memory.region[0].base)
physbase == base == 0, so you're left with "return aa".
So remove abs_to_phys(), and lmb_abs_to_phys() which is the implementation
of abs_to_phys() for iSeries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The lmb code is all written to use a pointer to an lmb struct. But it's always
the same lmb struct, called "lmb". So we take the address of lmb, call it
_lmb and then start using _lmb->foo everywhere, which is silly.
This patch removes the _lmb pointers and replaces them with direct references
to the one "lmb" struct. We do the same for some _mem and _rsv pointers which
point to lmb.memory and lmb.reserved respectively.
This patch looks quite busy, but it's basically just:
s/_lmb->/lmb./g
s/_mem->/lmb.memory./g
s/_rsv->/lmb.reserved./g
s/_rsv/&lmb.reserved/g
s/mem->/lmb.memory./g
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
physRpn_to_absRpn is a no-op on non-iSeries platforms, remove the two
redundant calls.
There's only one caller on iSeries so fold the logic in there so we can get
rid of it completely.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the msChunks struct to get rid of the StUdlY caps and make it a bit
clearer what it's for.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Chunks are 256KB, so use constants for the size/shift/mask, rather than
getting them from the msChunks struct. The iSeries debugger (??) might still
need access to the values in the msChunks struct, so we keep them around
for now, but set them from the constant values.
Replace msChunks_entry typedef with regular u32.
Simplify msChunks_alloc() to manipulate klimit directly, rather than via
a parameter.
Move msChunks_alloc() and msChunks into iSeries_setup.c, as that's where
they're used.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The msChunks code was written to work on pSeries, but now it's only used on
iSeries. This means there's no need to do PTRRELOC anymore, so remove it all.
A few places were getting "extern reloc_offset()" from abs_addr.h, move it
into system.h instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make firmware_has_feature() evaluate at compile time for the non pSeries
case and tidy up code where possible.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Create the firmware_has_feature() inline and move the firmware feature
stuff into its own header file.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The firmware_features field of struct cpu_spec should really be a separate
variable as the firmware features do not depend on the chip and the
bitmask is constructed independently. By removing it, we save 112 bytes
from the cpu_specs array and we access the bitmask directly instead of via
the cur_cpu_spec pointer.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc64 head.S defines several zero-initialized structures, such as
the empty_zero_page and the kernel top-level pagetable. Currently
they are defined to be in the data section. However, they're not used
until after the bss is cleared, so this patch moves them to the bss,
saving two and a half pages from the vmlinux.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adjust some comments in head.S for accuracy, clarity, and
spelling.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/ppc64/kernel/head.S #defines SECONDARY_PROCESSORS then has some
#ifdefs based on it. Whatever purpose this had is long lost, this
patch removes it.
Likewise, head.S defines H_SET_ASR, which is now defined, along with
other hypervisor call numbers in hvcall.h. This patch deletes it, as
well, from head.S.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An #if/#else construct near the top of ppc64's head.S appears to
create overlapping sections of code for iSeries and pSeries (i.e. one
thing on iSeries and something different in the same place on
pSeries). In fact, checking the various absolute offsets, it doesn't.
This patch unravels the #ifdefs to make it more obvious what's going
on. This accomplishes another microstep towards a single kernel image
which can boot both iSeries and pSeries.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As well as the interrupt vectors and initialization code, head.S
contains several asm functions which are used during runtime. This
patch moves these to misc.S, a more sensible location for random asm
support code. A couple The functions moved are:
disable_kernel_fp
giveup_fpu
disable_kernel_altivec
giveup_altivec
__setup_cpu_power3 (empty function)
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64 machines with segment tables, CPU0's segment table is at a
fixed address, currently 0x9000. This patch moves it to the free
space at 0x6000, just below the fwnmi data area. This saves 8k of
space in vmlinux and the runtime kernel image.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the ppc64 kernel head.S there is currently quite a lot of unused
space between the naca (at fixed address 0x4000) and the fwnmi data
area (at fixed address 0x7000). This patch moves various exception
vectors and support code into this region to use the wasted space.
The functions load_up_fpu and load_up_altivec are moved down as well,
since they are essentially continuations of the fp_unavailable_common
and altivec_unavailable_common vectors, respectively.
Likewise, the fwnmi vectors themselves are moved down into this area,
because while the location of the fwnmi data area is fixed by the RPA,
the vectors themselves can be anywhere sufficiently low.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Comments in head.S suggest that the iSeries naca has a fixed address,
because tools expect to find it there. The only tool which appears to
access the naca is addRamDisk, but both the in-kernel version and the
version used in RHEL and SuSE in fact locate the NACA the same way as
the hypervisor does, by following the pointer in the hvReleaseData
structure.
Since the requirement for a fixed address seems to be obsolete, this
patch removes the naca from head.S and replaces it with a normal C
initializer.
For good measure, it removes an old version of addRamDisk.c which was
sitting, unused, in the ppc32 tree.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch just splits out the pSeries specific parts of vio.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch allows us to have a different bus if matching function for
each platform.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the iSeries vio iommu tables cannot be used until after the vio bus has
been initialised, move the initialisation of the tables to there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch splits the iSeries specific parts out of vio.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/ppc64/Kconfig defines a "General setup" menu, but also sources
init/Kconfig which also defines a "General setup" menu. Both of these
menus appear at the top level of make menuconfig. Having two menus with
the same name is confusing. This patch renames the ppc64/Kconfig menu to
be "Bus Options" and moves options in this menu which are not bus related
to the end of the "Platform support" menu.
There are many variations among architectures on the exact naming of the
"Bus Options" menu. I chose to use the simplest one, which is also used
in arch/ppc/Kconfig.
Signed-off-by: Frank Rowand <frowand@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
OpenFirmware marks devices as failed in the device-tree when a hardware
problem is detected. The kernel needs to fail config reads/writes to
prevent a kernel crash when incorrect data is read.
This patch validates that the device-node is not marked "fail" when
config space reads/writes are attempted.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the format of the flattened device-tree passed
between the boot trampoline and the kernel to support a more compact
representation, for use by embedded systems mostly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement 4-level pagetables for ppc64
This patch implements full four-level page tables for ppc64, thereby
extending the usable user address range to 44 bits (16T).
The patch uses a full page for the tables at the bottom and top level,
and a quarter page for the intermediate levels. It uses full 64-bit
pointers at every level, thus also increasing the addressable range of
physical memory. This patch also tweaks the VSID allocation to allow
matching range for user addresses (this halves the number of available
contexts) and adds some #if and BUILD_BUG sanity checks.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the bootheader for ppc64 independent from kernel and libc headers.
* add -nostdinc -isystem $gccincludes to not include libc headers
* declare all functions in header files, also the stuff from string.S
* declare some functions static
* use stddef.h to get size_t (hopefully ok)
* remove ppc32-types.h, only elf.h used the __NN types
With further modifications by Paul Mackerras and Stephen Rothwell.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This kills i386-specific stuff from arm Kconfig. Please apply,
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- copy_from_user() can fail; ->write() must check its return value.
- severe buffer overruns both in ->read() and ->write() - lseek to the
end (i.e. to mmapper_size) and
if (count + *ppos > mmapper_size)
count = count + *ppos - mmapper_size;
will do absolutely nothing. Then it will call
copy_to_user(buf,&v_buf[*ppos],count);
with obvious results (similar for ->write()).
Fixed by turning read to simple_read_from_buffer() and by doing
normal limiting of count in ->write().
- gratitious lock_kernel() in ->mmap() - it's useless there.
- lots of gratuitous includes.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are currently reserving one byte more than actually needed by the flash
device and overlapping into the next I/O expansion bus window. This a)
causes us to allocate an extra page of VM due to ARM ioremap() alignment
code and b) could cause problems if another driver tries to request the
next expansion bus window.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some nodes can have large holes on x86-64.
This fixes problems with the VM allowing too many dirty pages because it
overestimates the number of available RAM in a node. In extreme cases you
can end up with all RAM filled with dirty pages which can lead to deadlocks
and other nasty behaviour.
This patch just tells the VM about the known holes from e820. Reserved
(like the kernel text or mem_map) is still not taken into account, but that
should be only a few percent error now.
Small detail is that the flat setup uses the NUMA free_area_init_node() now
too because it offers more flexibility.
(akpm: lotsa thanks to Martin for working this problem out)
Cc: Martin Bligh <mbligh@mbligh.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Be more precise on deciding whether to call m8xx_ide_init() at
m8xx_setup.c:platform_init().
Compilation fails if CONFIG_BLK_DEV_IDE is defined but
CONFIG_BLK_DEV_MPC8xx_IDE isnt.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
copy_page.o appeared twice in arch/ia64/lib/Makefile. The
one in global lib-y is wrong where it should be just in
lib-$(CONFIG_ITANIUM).
Both copy_page.o and copy_page_mck.o are build for Itanium2
processor and the link order will pick up the low performing
copy_page function (originally written for itanium processor).
In this case, we really want the copy_page_mck.o for optimized
version.
Signed-off-by: Kenneth Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch to support P-state transitions on ia64. This driver is based on ACPI,
and uses the ACPI processor driver interface to find out the P-state support
information for the processor. This driver plugs into generic cpufreq
infrastructure.
Once this driver is loaded successfully, ondemand/userspace governor can be
used to change the CPU frequency dynamically based on load or on request from
userspace process.
Refer :
ACPI specification -
http://www.acpi.info
P-state related PAL calls -
http://developer.intel.com/design/itanium/downloads/24869909.pdf
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
bte_copy() calls calls smp_processor_id(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead
because we are just using it to pick a BTE interface and are not
tied to a specific cpu.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to abstract irq_affinity down to the pci provider level since
different SGI hardware implements this in different ways.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Clean up of SGI SN partitioning related code.
The SN_SAL_GET_SN_INFO SAL call returns the partition ID, making
the SN_SAL_SYSCTL_PARTITION_GET SAL call redundant. Remove sn_partid
and use sn_partition_id.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the SN pci device info to use the nearest node function
to allocate driver memory on the nearest node (rather than
defaulting to node 0).
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add a new exported function for determining the nearest node
with CPUs for I/O nodes and fix a bug where the hwperf dynamic
misc device was being registered before misc_init().
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Bugfix to export PCI topology information in /proc/sgi_sn/sn_topology.
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently, region numbers are defined in several files, with several
names. For example, we have REGION_KERNEL in asm/page.h and
RGN_KERNEL in pgtable.h
We also have address definitions that should depend on the
RGN_XXX macros, but are currently just long constants.
The following patch reorganises all the definitions so that they have
the same form (RGN_XXX), are in one place, and that addresses that
depend on RGN_XXX are derived from them.
(This is a necessary but not sufficient patch to allow UML-like
operation on IA64).
Thanks to David Mosberger for catching the change I missed in mmu_context.h.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Kernel 2.6 doesn't support egcs, and I didn't find any user of this
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Removed IA64 architecture specific users of asm/segment.h
The removal of asm-ia64/segment.h itself can wait until all
of the kernel source has been purged of references.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibios_bus_to_resource is exported on all architectures except ia64
and sparc. Add exports for the two missing architectures. Needed when
Yenta socket support is compiled as a module.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I mistakedly disabled fusion support in an earlier update. Fusion
is commonly used on many x86-64 systems, so this was a problem.
This patch fixes that.
Signed-off-by: And Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch puts back the export of machine_power_off() that was removed
by some janitor as it's used for emergency shutdown by the G5 thermal
control driver. Wether that driver should use kernel_power_off() instead
is debatable and a post-2.6.13 decision. In the meantime, please commit
that patch that fixes the driver for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code to detect IO links on Opteron would not check
if the node had actually memory. This could lead to pci_bus_to_node
returning an invalid node, which might cause crashes later
when dma_alloc_coherent passes it to page_alloc_node().
The bug has been there forever but for some reason
it is causing now crashes.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 floating-point exception handling has a bug that can cause error
code 0 to be sent instead of the proper code during signal delivery.
This is caused by unconditionally checking the IS and c1 bits from the
FPU status word when they are not always relevant. The IS bit tells
whether an exception is a stack fault and is only relevant when the
exception is IE (invalid operation.) The C1 bit determines whether a
stack fault is overflow or underflow and is only relevant when IS and IE
are set.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
a bunch of functions switched from volatile to __attribute__((noreturn)) and
from const to __attribute_pure__
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
use of explicit labels in inline asm is a Bad Idea(tm), since gcc can
decide to inline the function in several places. Fixed by use of 1f/f:
instead of .Lfitsin/.Lfitsin:
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
either icu_data declaration for SMP case should be taken out of m32102.h,
or its declarations for m32700ut and opsput should not be static for SMP.
Patch does the latter - judging by comments in m32102.h it is intended to
be non-static.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
extern on physid_2_cpu[] does not belong in smp.h - the thing is static.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
"=m" (lock->lock) / "1" (lock->lock) makes gcc4 unhappy; fixed by s/1/m/,
same as in case of i386 rwsem.h where such variant had been accepted
by both Linus and rth.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
on UP smp_call_function() is expanded to expression. Alpha oprofile
calls that puppy and ignores the return value. And has -Werror for
arch/*...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PM is broken on 44x; removed duplicate entry for CONFIG_PM, made
the inclusion of generic one conditional on BROKEN || !44x.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MV64360 does not support IRQ_ALL_CPUS - see arch/ppc/kernel/mv64360_pic.c.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ppc SMP is supported only for 6xx/POWER3/POWER4 - i.e. ones that have
PPC_STD_MMU. Dependency fixed.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DEBUG_PAGEALLOC is broken on m32r - the option had been blindly copied from
i386; kernel_map_pages() had not and that's what is needed for DEBUG_PAGEALLOC
to work (or link, while we are at it).
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI support is broken on m32r (pci_map_... missing, etc.); marked as such
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NUMA is broken on m32r; marked as such
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NUMA is broken on alpha; marked as such
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thanks to Stephane, we've now worked out the real cause of the
`Linux will not boot on simulator' problem. Turns out it's a stack
overflow because the stack pointer wasn't being initialised properly
in boot_head.S (it was being initialised to the lowest instead of the
highest address of the stack, so the first push started to overwrite
data in the BSS).
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Plug a race in TSC synchronization
We need to do tsc_sync_wait() before the CPU is set online to prevent
multiple CPUs from doing it in parallel - which won't work because TSC
sync has global unprotected state.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm trying to get the nmi working with my laptop (IBM ThinkPad G41) and after
debugging it a while, I found that the nmi code doesn't want to set it up for
this particular CPU.
Here I have:
$ cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Mobile Intel(R) Pentium(R) 4 CPU 3.33GHz
stepping : 1
cpu MHz : 3320.084
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pni
monitor ds_cpl est tm2 cid xtpr
bogomips : 6642.39
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Mobile Intel(R) Pentium(R) 4 CPU 3.33GHz
stepping : 1
cpu MHz : 3320.084
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pni
monitor ds_cpl est tm2 cid xtpr
bogomips : 6637.46
And the following code shows:
$ cat linux-2.6.13-rc6/arch/i386/kernel/nmi.c
[...]
void setup_apic_nmi_watchdog (void)
{
switch (boot_cpu_data.x86_vendor) {
case X86_VENDOR_AMD:
if (boot_cpu_data.x86 != 6 && boot_cpu_data.x86 != 15)
return;
setup_k7_watchdog();
break;
case X86_VENDOR_INTEL:
switch (boot_cpu_data.x86) {
case 6:
if (boot_cpu_data.x86_model > 0xd)
return;
setup_p6_watchdog();
break;
case 15:
if (boot_cpu_data.x86_model > 0x3)
return;
Here I get boot_cpu_data.x86_model == 0x4. So I decided to change it and
reboot. I now seem to have a working NMI. So, unless there's something know
to be bad about this processor and the NMI. I'm submitting the following
patch.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Acked-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparc_ksyms.c used to declare weak alias to several gcc intrinsics. It
doesn't work with gcc4 anymore - it wants a declaration for the thing
we are aliasing to and that's not going to happen for something like
.mul, etc. Replaced with direct injection of weak alias on the assembler
level - .weak <alias> followed by <alias> = <aliased>; that works on all
gcc versions.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC 4.x really dislikes the games we are playing in
unaligned.c, and the cleanest way to fix this is to
move things into assembler.
Noted by Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix swiotlb sizing to match what the comments and the kernel
parameters documentation indicate. Given a default 16k page size kernel
(ia64) and a 2k swiotlb page size, we're off by a multiple of 8 trying
to size the swiotlb. When specified on the boot line, the swiotlb is
made 8x bigger than requested. When left to the default value, it's 8x
smaller than the comments indicate. For x86_64 the multiplier would be
2x. The patch below fixes this. Now, what's a good default swiotlb
size? Apparently we don't really need 64MB.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
After building a fresh tree with gcc 4 I can't boot the simulator as
the bootloader loader dies with
loading /home/ianw/kerntest/kerncomp//build/sim_defconfig/vmlinux...
failed to read phdr
After some investigation I believe this is do with differences between
the alignment of variables on the stack between gcc 3 and 4 and the
ski simulator. If you trace through with the simulator you can see
that the disk_stat structure value returned from the SSC_WAIT_COMPLETION
call seems to be only half loaded. I guess it doesn't like the alignment
of the input.
Signed-off-by: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since early CPU identify is in this information is already available
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes build on 4xx stb03xxx when general purpose dma engine support is
enabled.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Running UML inside a detached screen delivers SIGWINCH when UML is not
expecting it. This patch ignores them.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
asm/elf.h breaks the x86_64 build.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add inotify and ioprio syscall stubs to SH64.
Signed-off-by: Robert Love <rml@novell.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add inotify and ioprio syscall stubs to SH.
Signed-off-by: Robert Love <rml@novell.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add platform device data for the SA11x0 MCP device. This allows
platforms to customise the configuration of the SA11x0 MCP device
according to their needs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the core of the multimedia communication port
framework. This is a port used to communicate with devices
with two DMA paths and a control path.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Shub2 provides a much improved mechanism for issuing internode
TLB purges. Add code to support the newer mechanism. There is also
some debug code (disabled) that is useful for testing.
Collect statistics on the number, type & duration of TLB purges.
This data will be useful for making future improvements in the algorithms.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change the BTE driver so that it works for both shub1 and
shub2. Most of the changes are related to the number of cores
that use the BTE engine, to the MMR addresses of various
shub registers, and to using the correct processor or network
physical address.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Disable some shub1-specific code when running on systems with shub2.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the addresses of the pio_write_status_addr so that
they are correct for newer processors. Shub2 did not number
the threads in the order that I had expected.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use local SHUB alias space when referencing MMRs that are known
to be node local. There is a slight performance benefit & code
simplification.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes a bug in the PPC64 iommu vmerge code which results in the
potential for iommu_unmap_sg to go off unmapping more than it should.
This was found on a test system which resulted in PCI bus errors due to
PCI memory being unmapped while DMAs were still in progress.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Dimitry Andric
This patch removes the initial UART I/O mapping from s3c2410_iodesc,
since the same mapping is already done in the function s3c24xx_init_io
in the file arch/arm/mach-s3c2410/cpu.c, through the s3c_iodesc array.
I'm not sure if duplicate mappings do any harm, but it's simply
redundant. Also, in s3c2440.c the UART I/O mapping is NOT done.
Additionally, I put a comma behind the last mapping, to ease
copy/pasting stuff around, and make the style consistent with
s3c2440.c and other files.
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sean Lee
In the arch/arm/mm/Kconfig file, the CPU_DCACHE_WRITETHROUGH
option is depend on the CPU_DISABLE_DCACHE, but the "Disable
D-Cache" option is configured as CPU_DCACHE_DISABLE.
The CPU_DISABLE_DCACHE should be CPU_DCACHE_DISABLE
Signed-off-by: Sean Lee <beginner2arm@eyou.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paulus suggested that we put xLparMap in its own .c file so that we can
generate a .s file to be included into head.S. This doesn't get around
the problem of having it at a fixed address, but it makes it more
palatable.
It would be good if this could be included in 2.6.13 as it solves our
build problems with various versions of binutils and gcc. In
particular, it allows us to build an iSeries kernel on Debian unstable
using their biarch compiler.
This has been built and booted on iSeries and built for pSeries and g5.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just `make oldconfig' doesn't help for the zx1 defconfig ---
because we need the MPT Fusion drivers, which are picked up as not
selected.
Tested on HP ZX2000 and ZX2600.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The main issue is that bus_fixup calls may potentially call
functions that require a valid bus->sysdata pointer. Since
this is the case, we must set the bus->sysdata pointer before
calling the bus_fixup functions. The remaining changes are
simple fixes to make sure memory is cleaned up in the function.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The current one doesn't even make sense anymore on i386 where it
apparently came from.
Follow-up wordsmithing by Matthew Wilcox and Tony Luck.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Richard Purdie
The exception handling code fails to compile if the extended
precision mode is enabled. This patch fixes those compile errors and
also stops _quiet functions from incorrectly raising exceptions.
Reported-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Oops. I knew I didn't have the physical versus logical cpu identifiers right
when I generated that patch. It's not nearly as bad as I feared at the time
though.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Altix patch to add an SN pci provider for TIOCE, which is SGI's
PCI Express implementation.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to add TIO "huge-window" address support to sn_dma_flush().
Update copyright in affected files.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to abstract the force_interrupt() mechanism away from the
pcibr provider.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cosmetic altix patch to rename SGI_PCIBR_ERROR to something more generic and
remove a duplicate #define.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The PFM_LOAD_CONTEXT may fail silently and cause a session
to remain reserved even though it should not. This can happen
when the commands succeeds in reserving the session but fails
when it actually tries to attach to the load_pid. In that case,
the command has failed but will return 0. More importantly,
the session will remain reserved. This patch fixes the problem.
Signed-off-by: <stephane.eranian@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The workaround for broken device-tree that prevents fan control from
working on recent G5 models need to be "enabled" for machines with
revision 0x37 of the bridge in addition to machines with revision 0x35.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Rename the s3c2410_report_oc() to s3c2410_usb_report_oc()
as this is an usb specific function.
Change port power on the usb-simtec implementation to only
power up the output if both are set, as per the usb 1.1
specification
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, we can't use the "user" bit in the page tables to
control whether a page table entry is "global" or "asid" specific,
since the vector page is mapped as "user" accessible but is not
process specific.
Therefore, give direct control of the ARMv6 "nG" (not global)
bit to the mm layers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Dave Johnson <djohnson+linux-kernel@sw.starentnetworks.com>
sendmsg()/recvmsg() syscalls from o32/n32 apps to a 64bit kernel will
cause a kernel memory leak if iov_len > UIO_FASTIOV for each syscall!
This is because both sys_sendmsg() and verify_compat_iovec() kmalloc a
new iovec structure. Only the one from sys_sendmsg() is free'ed.
I wrote a simple test program to confirm this after identifying the
problem:
http://davej.org/programs/testsendmsg.c
Note that the below fix will break solaris_sendmsg()/solaris_recvmsg() as
it also calls verify_compat_iovec() but expects it to malloc internally.
[ I fixed that. -DaveM ]
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert commit fec59a711e, which is
breaking sparc64 that doesn't have a working pci_update_resource.
We'll re-do this after 2.6.13 when we'll do it all properly.
this changeset broke the "nohalt" kernel boot option.
8df5a500a3
default_idle() is looking at new variable can_do_pal_halt. However,
that variable did not get cleared upon "nohalt" boot option. Result
is that "nohalt" option is ignored until perfmon is exercised.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
modprobe aes does not work on x86_64. i386 has a similar line, this could
be the right fix. Would be nice to have in 2.6.13 final.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory mappings for MPC8349 USB MPH and DR modules were reversed.
Signed-off-by: Li Yang <LeoLi@freescale.com>
Signed-off-by: Jiang Bo <Tanya.jiang@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a bpa_defconfig file and make target. The config settings
are made for the current version of the Cell Processor Based Blade,
so there are not too many drivers enabled. A few more drivers might
get added in the future though.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the fix to align node_end_pfns to a proper location. The earlier fix
made the node_remap_start_vaddr to get misaligned causing remap_numa_kva to
barf again :-/
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Touching the pte directly causes the 8Mbyte TLB entry to be invalidated.
This has been fixed in v2.4 for ages.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
8xx: restrict ENET_BIG_BUFFERS option to drivers which actually use it
Signed-off-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch add stubs to allow the visws subarch to link again.
Signed-off-by: Tom Duffy <thomas.duffy.99@alumni.brown.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't log machine check events left over from boot. Too many BIOSes leave
bogus events in there.
This unfortunately also makes it impossible to log events that caused a
reboot. For people with non broken BIOS there is mce=bootlog
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the sparse mem changes and the kexec changes
were merged into setup.c they came in, in the wrong order.
This patch changes the order so we don't run sparse_init
which uses the bootmem allocator until we all of the
reserve_bootmem calls has been made.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another x86 subarchitecture bit I missed. This adds both
machine_emergency_restart missed in my reboot fixes and
machine_shutdown needed for kexec support.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is one more bit of breakage my x86 sub-architecture
confusion caused.
Add machine_shutdown to voyager so it will compile with CONFIG_KEXEC.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we did the handle_mm_fault cleanup and get_user_page() race fixes,
handle_mm_fault turned into an inline function that called the real
__handle_mm_fault() code. The export needed for MOL on ppc wasn't
updated to match the new world order, though.
Turn it into a GPL export while at it, since this is all about internal
interfaces and MOL is GPL'd anwyay.
[PATCH] i386: Implement machine_emergency_reboot
introduced this new function into arch/i386/reboot.c. However,
subarchitectures are entitled to implement their own copies of reboot.c
from which this new function is now missing.
It looks like visws will also need a similar fixup
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In yenta_socket, we default to using the resource setting of the CardBus
bridge. However, this is a PCI-bus-centric view of resources and thus needs
to be converted to generic resources first. Therefore, add a call to
pcibios_bus_to_resource() call in between. This function is a mere wrapper on
x86 and friends, however on some others it already exists, is added in this
patch (alpha, arm, ppc, ppc64) or still needs to be provided (parisc -- where
is its pcibios_resource_to_bus() ?).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0. This leaves such
a device in an inaccessible state. The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.
The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.
Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot. Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.
Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification. This is
especially true since often many devices are covered by the same
driver. It likely would be necessary to replicate code across dozens
of drivers.
The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register. I believe it is safe to include
this patch as part of the PCI infrastructure.
The cleanest implementation of pci_restore_bars was to call
pci_update_resource. Unfortunately, that does not currently exist
for the sparc64 architecture. The patch below includes a null
implemenation of pci_update_resource for sparc64.
Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IA32 ptrace emulation currently returns the wrong registers for fs/gs;
it's returning what x86_64 calls gs_base. We need regs.gsindex in order
for GDB to correctly locate the TLS area. Without this patch, the 32-bit
GDB testsuite bombs on a 64-bit kernel. With it, results look about like
I'd expect, although there are still a handful of kernel-related failures
(vsyscall related?).
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had a user whose apps weren't working correctly because his "rtc" wasn't
working fully.
For the sake of simplicity, it seems sensible to always enable HPET RTC
emulation.
Remove a special config option for HPET_EMULATE_RTC and make it directly
depend on HPET_TIMER and RTC. This will avoid the hangs when EMULATE_RTC
is not configured and when some userlevel script depends on RTC interrupt,
as in:
http://bugzilla.kernel.org/show_bug.cgi?id=4904
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kexec boot is not successful on some power machines since all CPUs are
getting removed from global interrupt queue (GIQ) before kexec boot. Some
systems always expect at least one CPU in GIQ. Hence, this patch will make
sure that only secondary CPUs are removed from GIQ.
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_KEXEC breaks UP builds because of a misspelled smp_release_cpus().
Also, the function isn't defined unless built with CONFIG_SMP but it is
needed if we are to go from a UP to SMP kernel. Enable it and document it.
Thanks to Steven Winiecki for reporting this and to Milton for remembering
how it's supposed to work and why.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Michael Gernoth
As discussed on the handhelds.org Jornada mailinglist, I take over
maintainership of the currently unmaintained Jornada 720-port in
the mainline kernel.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
x86_64 had hardcoded the VM_ numbers so it broke down when the numbers
were changed.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Fix a typo causing a warning in the arm oprofile backtrace code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM fault handler is optimised to make the fast path, err, fast.
The renumbering of the VM_FAULT_* codes broke this because numbers
were used instead of the definitions. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This allows the serial driver autconf to work properly on all the IXP
serial ports. W/o it we basically put the serial port in an unrecoverable
state and lose console.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The IEEE 754 standard specifies that the result of (x - x), where x is
a valid number, should be -0 if the rounding mode is towards minus
infinity or +0 otherwise.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
The XScale locking code is not something that has been validated
on 2.6 and needs to be replaced with a more generic API to use
with other ARMs that support locking features.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
NWFPE used global variables which meant it wasn't safe for use with
preemptive kernels. This patch removes them and communicates the
information between functions in a preempt safe manner. Generation
of some exceptions was broken and this has also been corrected.
Tests with glibc's maths test suite show no change in the results
before/after this patch.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The default clock rate does not specify a maximum, so the
default of 400KHz is used. This rate is too fast for the PMU
on the EB2410ITX, so we now specify platform data with a rate
of around 100KHz.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For soft reset during system hang, got an error "CPU did not take
control" for some CPUs even though they responded to soft-reset (called
SystemReset, die and called debugger - xmon). First these CPUs entered
into xmon by IPI callback and then got a soft-reset exception and
re-entered into xmon again. The first CPU which re-entered into xmon got
the output lock and made into xmon successfully without unlocking.
Hence, the next CPU(s) which re-entered into xmon try to acquire a lock
(get_output_lock). Therefore, we can not view state of those CPU(s).
[This is a simple, very low risk, obvious fix for an obvious bug, and
should go into 2.6.13. -- paulus]
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If CONFIG_NUMA is set, some POWER 4 systems will fail to boot. This is
because of special processing needed to handle invalid node IDs (0xffff) on
POWER 4. My previous patch to handle memory 'holes' within nodes forgot to
add this special case for POWER 4 in one place.
In reality, I'm not sure that configuring the kernel for NUMA on POWER 4 makes
much sense. Are there POWER 4 based systems with NUMA characteristics that
are presented by the firmware? But, distros want one kernel for all systems
so NUMA is on by default in their kernels. The patch handles those cases.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug found by Grant Coady <lkml@dodo.com.au>'s autobuild setup.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
