Use the newly added .bss.page_aligned section for aligning the stacks
rather than THREAD_SIZE.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need to know the CPU ID in order to calculate the mask and ack
registers effectively. Stub this in for UP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the ipr code by grouping the offset array together
with the ipr_data structure in a new data structure called ipr_desc.
This new structure also contains the name of the controller in struct
irq_chip. The idea behind putting struct irq_chip in there is that we
can use offsetof() to locate the base addresses in the irq_chip
callbacks. This strategy has much in common with the recently merged
intc2 code.
One logic change has been made - the original ipr code enabled the
interrupts by default but with this patch they are all disabled by
default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The shared intc2 code currently contains cpu-specific #ifdefs.
This is a tad unclean and it prevents us from using the shared code
to drive board-specific irqs on the se7780 board.
This patch reworks the intc2 code by moving the base addresses of
the intc2 registers into struct intc2_desc. This new structure also
contains the name of the controller in struct irq_chip. The idea
behind putting struct irq_chip in there is that we can use offsetof()
to locate the base addresses in the irq_chip callbacks.
One logic change has been made - the original shared intc2 code
enabled the interrupts by default but with this patch they are all
disabled by default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-2 can presently get in to some pretty bogus states, so
we tidy up the dependencies a bit and get it all building
again.
This gets us a bit closer to a functional allyesconfig
and allmodconfig, though there are still a few things to
fix up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was added during 2.5.x, but was never moved along. This
can easily be resurrected if someone has one they wish to work
with, but it's not worth keeping around in its current form.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently cpu_to_node() is always 0 in the UP case, though
we do want to have the CPU association linked in under sysfs
even in the cases where we're only on a single CPU.
Fix this up, so we have the cpu0 link on all of the available
nodes that don't already have a CPU link of their own.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds the URAM block on SH7722 as a separate node.
Sparsemem is required for this, or it can simply be disabled
by explicitly selecting a flatmem model.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We have to call in to sparse_memory_present_with_active_regions()
earlier in order for sparsemem to be happy. This was being called
too late, and was causing troubles with the platforms that needed
to enable sparsemem.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements basic sparsemem support for SH. Presently this only
uses static sparsemem, and we still permit explicit selection of
flatmem. Those boards that want sparsemem can select it as usual.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
.machvec.init can be misaligned with the recent machvec changes,
forcibly align it on the boundary that it expects, as before.
Signed-off-by: Takashi YOSHII <takashi.yoshii.ze@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that select no longer works for selecting the "closest" CPU,
we have to explicitly reference the precise sub-type in the few
places where it actually matters (presently only setup code and
some legacy sh-sci cruft).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This kills off the BareCPU board as a "special" machvec, rather,
we leave this as a default for when no other vector is available,
or when we want to use it in combination with other vectors for
testing with generic ops. As sh_mv is copied out anyways (or
overloaded when an alternate vector is explicitly selected), this
doesn't consume any additional memory.
The generic machvec can be forcibly selected with sh_mv=generic,
or by not having any other boards enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We now throw all of the machvecs in to .machvec.init and either
select one on the command line, or copy out the first (and
usually only) one to sh_mv. The rest are freed as usual.
This gets rid of all of the silly sh_mv aliasing and makes the
selection explicit rather than link-order dependent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up much of the machvec handling, allowing for it to be
overloaded on boot. Making practical use of this still requires
some Kconfig munging, however.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in some more __user annotations. These weren't being
handled properly in some of the __get_user and __put_user paths,
so tidy those up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Split out the CPU topology initialization to a separate file,
and switch it to a percpu type, rather than an NR_CPUS array.
At the same time, switch to only registering present CPUs,
rather than using the possible CPU map.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the SH7722 changes, ->set_rate() also takes an algo_id,
SH4-202 was overlooked when this change went in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_KGDB_NMI is disabled, we're left with a stray in_nmi
reference that can't be resolved. Move the symbol under the ifdef,
too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Several errors were spotted during building for custom config (SMP
included). Although SMP still does not compile (no ipi and
__smp_call_function) and does not work, this looks a bit cleaner.
Some other errors obtained via gcc-4.1.0 build.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CC arch/sh/kernel/vsyscall/vsyscall.o
a/arch/sh/kernel/vsyscall/vsyscall.c: In function 'arch_setup_additional_pages':
a/arch/sh/kernel/vsyscall/vsyscall.c:63: error: dereferencing pointer to incomplete type
a/arch/sh/kernel/vsyscall/vsyscall.c:67: error: dereferencing pointer to incomplete type
a/arch/sh/kernel/vsyscall/vsyscall.c:82: error: dereferencing pointer to incomplete type
a/arch/sh/kernel/vsyscall/vsyscall.c:85: error: dereferencing pointer to incomplete type
a/arch/sh/kernel/vsyscall/vsyscall.c: In function 'arch_vma_name':
a/arch/sh/kernel/vsyscall/vsyscall.c:91: error: dereferencing pointer to incomplete type
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add lost in_nmi definition to solve pcrel too far.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the master clock multiplier and initial rate
propagation for the SH7722 clocks.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we have the basic kdump support in place, add it in to
die() so we can enter the crash kernel automatically.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As pointed out by Saito-san, without the sr.bl manipulation we can
occasionally hit delays in the idle loop due to interrupt handling, so
ensure that interrupts are blocked before going to sleep.
At the same time, we throw in TIF_POLLING_NRFLAG for the !hlt_counter
case (primarily used by the ST-40 parts).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- setup-sh7750.c only defines the sh7751_ipr_map when building
with SH7751 support.
- 7722 Solution Engine was missing a mach-type entry, causing
the macro in cf-enabler to be undefined.
- arch/sh/mm/init.c needs linux/pagemap.h.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When the stacktrace simplification changes went in the function
definition on SH got skipped, fix it up so things build again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds basic support for clockevents and clocksources,
presently only implemented for TMU-based systems (which
are the majority of SH-3 and SH-4 systems).
The old NO_IDLE_HZ implementation is also dropped completely,
the only users of this were on TMU-based systems anyways.
More work needs to be done to generalize the TMU handling,
in that the current implementation is rather tied to the
notion of TMU0 and TMU1 utilization.
Additionally, as more SH timers switch over to this scheme,
we'll be able to gut most of the remaining system timer
infrastructure that existed before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
There are a few different cases for figuring out how to
size the instruction. We read in the instruction located
at regs->pc - 4 when rewinding the opcode to figure out if
there's a 32-bit opcode before the faulting instruction, with
a default of a - 2 adjustment on a mismatch. In practice this
works for the cases where pc - 4 is just another 16-bit opcode,
or we happen to have a 32-bit and a 16-bit immediately
preceeding the pc value.
In the cases where we aren't rewinding, this is much less ugly..
We also don't bother fixing up the places where we're explicitly
dealing with 16-bit instructions, since this might lead to
confusion regarding the encoding size possibilities on other
CPU variants.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-2A supports both 16 and 32-bit instructions, add a simple helper
for figuring out the instruction size in the places where there are
hardcoded 16-bit assumptions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
