cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
* 'fixes-s3c-2632-rc5' of git://git.fluff.org/bjdooks/linux:
ARM: S3C2410: Fix sparse warnings in arch/arm/mach-s3c2410/gpio.c
ARM: S3C2440: mini2440: Fix spare warnings
ARM: S3C24XX: Fix warnings in arch/arm/plat-s3c24xx/gpio.c
ARM: S3C2440: mini2440: Fix missing CONFIG_S3C_DEV_USB_HOST
ARM: S3C24XX: arch/arm/plat-s3c24xx: Move dereference after NULL test
ARM: S3C: Fix adc function exports
ARM: S3C2410: Fix link if CONFIG_S3C2410_IOTIMING is not set
ARM: S3C24XX: Introduce S3C2442B CPU
ARM: S3C24XX: Define a macro to avoid compilation error
ARM: S3C: Add info for supporting circular DMA buffers
ARM: S3C64XX: Set rate of crystal mux
ARM: S3C64XX: Fix S3C64XX_CLKDIV0_ARM_MASK value
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: ensure initial page tables are setup for SMP systems
ARM: 5776/1: Check compiler version and EABI support when adding ARM unwind support.
ARM: 5774/1: Fix Realview ARM1176PB board reboot
ARM: Fix errata 411920 workarounds
ARM: Fix sparsemem with SPARSEMEM_EXTREME enabled
ARM: Use GFP_DMA only for masks _less_ than 32-bit
ARM: integrator: allow Integrator to be built with highmem
ARM: Fix signal restart issues with NX and OABI compat
Mapping the same memory using two different attributes (memory
type, shareability, cacheability) is unpredictable. During boot,
we encounter a situation when we're updating the kernel's page
tables which can lead to dirty cache lines existing in the cache
which are subsequently missed. This causes stack corruption,
and therefore a crash.
Therefore, ensure that the shared and cacheability settings
matches the configuration that will be used later; this together
with the restriction in early_cachepolicy() ensures that we won't
create a mismatch during boot.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM unwind is known to compile only with EABI and not-buggy compilers.
The problem is not the unwinding information but the -fno-frame-pointer
option added as a result of !CONFIG_FRAME_POINTER. Now we check the
compiler and raise a #warning in case of wrong compiler.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the fix for proper reboot of Realview ARM1176PB board
when issuing the reboot command. Setting the eighth bit of
control register SYS_RESETCTL to 1 to force a soft reset.
arch_reset() is modified for realview machines to call machine
specific reset function pointers.
Signed-off-by: Philby John <pjohn@in.mvista.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Errata 411920 indicates that any "invalidate entire instruction cache"
operation can fail if the right conditions are present. This is not
limited just to those operations in flush.c, but elsewhere. Place the
workaround in the already existing __flush_icache_all() function
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When SPARSEMEM_EXTREME is enabled, memory_present() wants to use bootmem
to allocate data structures. However, we call memory_present() after
declaring memory to bootmem, but before we've reserved areas.
This leads to sparsemem data structures being overwritten later in the
kernel's initialization (when slab initializes.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap4: Fix UART4 platform data on omap4
omap4: Allow omap_serial_early_init() for OMAP4430 board
omap3: PM: enable UART3 module wakeups
omap2: Fix console serial port number for n8x0
omap2: Fix detection of n8x0
omap1: Fix DSP public peripherals support for ams-delta
omap1: Fix redundant UARTs pin muxing that can break other hardware support
omap: iommu: fix wrong condition check for SUPERSECTION
omap: SDMA: Fix omap_stop_dma() API for channel linking
omap: Fix omap-keypad by restoring old keypad.h without breaking omap2 boards that use matrix_keypad
Fix sparse warning in arch/arm/mach-s3c2410/gpio.c due to missing
include of <mach/gpio-fns.h>. Fixes the following warning:
warning: symbol 's3c2410_gpio_irqfilter' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in arch/arm/mach-s3c2440/mach-mini2440.c
due to missing 'static'.
warning: symbol 'mini2440_lcd_cfg' was not declared. Should it be static?
warning: symbol 'mini2440_fb_info' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following warnings from sparse in arch/arm/plat-s3c24xx/gpio.
due to the missing include of <mach/gpio-fns.h>
gpio.c:36:6: warning: symbol 's3c2410_gpio_cfgpin' was not declared. Should it be static?
gpio.c:84:14: warning: symbol 's3c2410_gpio_getcfg' was not declared. Should it be static?
gpio.c:103:6: warning: symbol 's3c2410_gpio_pullup' was not declared. Should it be static?
gpio.c:125:5: warning: symbol 's3c2410_gpio_getpull' was not declared. Should it be static?
gpio.c:138:6: warning: symbol 's3c2410_gpio_setpin' was not declared. Should it be static?
gpio.c:157:14: warning: symbol 's3c2410_gpio_getpin' was not declared. Should it be static?
gpio.c:184:5: warning: symbol 's3c2410_gpio_getirq' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix missing select of S3C_DEV_USB_HOST when building for mini2440
only. Fixes the following error:
built-in.o: undefined reference to `s3c_device_usb`
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the NULL test on buf is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the export of s3c_adc_read.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
[ben-linux@fluff.org: remove unexport of s3c_adc_start, needed for ts]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the link errors if cpu-frequency support is enabled on s3c2410 systems
but there is no CONFIG_S3C2410_IOTIMING set. Fix this by ensuring the
relevant symbols are defined NULL if the code is not being built in.
Fixes the following error:
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_get'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_set'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_calc'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the S3C2442B CPU ID to aid support the Openmoko GTA02 / Freerunner.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: edit description for clarity and S3C2442B as uppercase]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define a macro to avoid the following error during kernel build process
for platforms other than s3c2410:
arch/arm/plat-s3c24xx/cpu.c:84: error: ‘s3c2410a_init’ undeclared here (not in a function)
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX DMA implementation will work a lot better with the ability
to enqueue circular buffers as the hardware can do it's own linked-list
management.
Add a function s3c_dma_has_circular() to show that the system can do this
and a flag for the channel.
Update the s3c24xx/s3c64xx I2S DMA code to deal with this.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Mark Brown <broonie@@opensource.wolfsonmicro.com>
The current code assumes that the external clock mux will be set to
the crystal. Set this up explicitly within the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the values of S3C6400_CLKDIV0_ARM_MASK and S3C6410_CLKDIV0_ARM_MASK.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We were using GFP_DMA for masks other than 0xffffffff, which is
wrong when some masks are initialized to 0xffffffffffffffff.
This caused such masks to obtain memory from the precious DMA
pool.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes Integrator builds with highmem enabled; we need to
translate from 'struct page' to a DMA address, and this is not
possible without __pfn_to_bus().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The signal restarting code was placed on the user stack when OABI
compatibility is enabled. Unfortunately, with an EABI NX executable,
this results in an attempt to run code from the non-executable stack,
which segfaults the application.
Fix this by placing the code in the vectors page, along side the
signal return code, and directing the application to that code.
Reported-by: saeed bishara <saeed.bishara@gmail.com>
Tested-by: saeed bishara <saeed.bishara@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the unnecessary UART4 platform which is under
data is wrong because of this
There is a separate platform structure for UART4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables omap_serial_early_init() function for OMAP4430
SDP. Without this the bootup would throw oops in omap_serial_init().
Note that the ifndef CONFIG_ARCH_OMAP4 is split into two sections
to enable omap_serial_early_init(). This ifndef cannot be removed
until omap4 clock framework is implemented.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Tony Lindgren <tony@atomide.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 is in the PER powerdomain. If PER goes idle/inactive
independently of CORE, for UART3 to wakeup it must have its wakeup
enable bits setup in PM_WKEN_PER. This patch enables these bits.
The reason it works when PER and CORE work together is because when
CORE goes inactive/retention, the IOPAD wakeups are enabled and
trigger UART3 wakeup.
Without this patch, when the UART inactivity timer fires for UART3,
its clocks are disabled and it's unable to wakeup so will be unusable
until PER is awoken by another source.
Another way of testing is by keeping CORE on during suspend but
allowing PER to hit retention
# echo 3 > /debug/pm_debug/core_pwrdm/suspend
then enter suspend
# echo mem > /sys/power/state
Without this patch, UART3 will be unable to wakeup the system.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the recent changes omap serial ports match the physical
numbering like they should. Fix the kernel CMDLINE accordingly
so console works.
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSP public peripherals used to work on OMAP1510 based (or all OMAP1 class?)
machines as long as old dspgateway code were present in the l-o tree. For
several months it is no longer included, breaking support for McBSP1 based
audio on Amstrad Delta, for example.
This patch, derived from the old dspgateway code, corrects the problem for the
board by simply taking the DSP out of reset state, I guess. That way, things
should not break when a new dsp code is added to the tree, and the change can
be reverted then.
If there are any reports on McBSP1 or other DSP public peripherals not working
for other OMAP1 machines (I've not heard of any for now), I can prepare a more
general patch providing an extra include file with a helper function defined.
Created and tested against linux-2.6.32-rc5
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 15ac408ee5 removed enabled_uart
and OMAP_TAG_UART. This works for mach-omap2, but causes issues on
mach-omap1 for some boards as the mach-omap1 serial.c was muxing
pins based on the enabled_uart flag for 15xx.
Fix this by muxing pins in board-*.c files for the 15xx boards for
the uart ports that had enabled_uart flag set before the commit
above.
Tested on Amsdtrad Delta only.
Note that in the future we should add support for powering down
the uarts with a timer like mach-omap2/serial.c does. Otherwise
the enabled uarts will be blocking retention-while-idle.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A bit (2 << 0) is set both on SECTION and SUPERSECTION. To identify
SUPERSECTION correctly, other bits should be compared too.
Reported-by: "Srinivas Pulukuru" <srinivas.pulukuru@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP sDMA driver API omap_stop_dma() doesn't really stop the dma when used
in linking scenario.
The DMA channel needs to be disabled before resetting the chain.
Also fix clearing of the OMAP_DMA_ACTIVE status in the linked case.
Cc: Hari n <hari.zoom@gmail.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only mach-omap2 boards are currently using matrix_keypad. Allow
mach-omap1 boards to use the old style keypad.h without breaking.
Created against linux-2.6.32-rc5.
Compile tested with omap_3430sdp_defconfig and rx51_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the URL listed for Maverick EP9312 since it is not available
and modify the help text appropriately.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove unnecessary code in ep93xx_gpio_ab_irq_handler().
The desc calculation for gpio port B was left in when the following
commit was merged.
commit d8aa0251f1
Author: Dmitry Baryshkov <dbaryshkov@gmail.com>
Date: Thu Oct 9 13:36:24 2008 +0100
[ARM] 5298/1: Drop desc_handle_irq()
It's not needed so remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove unused prototype for ep93xx_init_time(). This function
is not defined in the kernel.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the U300 to use all the drivers merged in during the
2.6.32 merge window.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The macro for the watchdog has been changed from CONFIG_AT91SAM9_WATCHDOG
to CONFIG_AT91SAM9X_WATCHDOG due to AT91CAP9 chips support
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Updating desc for lid keys and resending patch with proper comments:
Define Spitz buttons as GPIO keys in a way compatible with the old driver:
On/Off: As Suspend EV_PWR key
Raw values of lid sensors SWA and SWB: As EV_SW switches
SWA: Display Down
SWB: Lid Closed
Recommended user space decoding:
SWA==0 & SWB==0: lid opened (landscape mode)
SWA==1 & SWB==0: invalid (or mechanic race condition)
SWA==0 & SWB==1: lid closed with display up (portrait mode or mechanic
race condition while closing to display-less mode)
SWA==1 & SWB==1: lid closed with display down (display-less mode)
AK_INT remote trigger is not mapped as input event. Without complete
remote driver and remote pull-up control it has no useful
interpretation.
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CM-X300 has libertas on mmc2 and SD card slot on mmc1.
This patch fixes wrong MMC ports assignment.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2xxx clock: set up clockdomain pointer in struct clk
OMAP: Fix race condition with autodeps
omap: McBSP: Fix incorrect receiver stop in omap_mcbsp_stop
omap: Initialization of SDRC params on Zoom2
omap: RX-51: Drop I2C-1 speed to 2200
omap: SDMA: Fixing bug in omap_dma_set_global_params()
omap: CONFIG_ISP1301_OMAP redefined in Beagle defconfig
This patch fixes the BUG: using smp_processor_id() in preemptible
Below is the stripped backtrace.
BUG: using smp_processor_id() in preemptible [00000000] code: init/1
caller is flush_tlb_mm+0x44/0x70
Backtrace:
[<c00225c4>] (dump_backtrace+0x0/0x110) from [<c01713a0>] (dump_stack+0x18/0x1c)
r7:00000000 r6:c00234f0 r5:00000001 r4:c7828000
[<c0171388>] (dump_stack+0x0/0x1c) from [<c0135364>] (debug_smp_processor_id+0xc0/0xf0)
[<c01352a4>] (debug_smp_processor_id+0x0/0xf0) from [<c00234f0>] (flush_tlb_mm+0x44/0x70)
r7:00000000 r6:c60b41a0 r5:c60b4154 r4:00000001
[<c00234ac>] (flush_tlb_mm+0x0/0x70) from [<c0039568>] (dup_mm+0x304/0x38c)
r5:c1f09058 r4:00000000
[<c0039264>] (dup_mm+0x0/0x38c) from [<c0039de4>] (copy_process+0x7b8/0xeb0)
[<c003962c>] (copy_process+0x0/0xeb0) from [<c003a638>] (do_fork+0x15c/0x29c)
[<c003a4dc>] (do_fork+0x0/0x29c) from [<c0021df0>] (sys_clone+0x34/0x3c)
[<c0021dbc>] (sys_clone+0x0/0x3c) from [<c001efa0>] (ret_fast_syscall+0x0/0x2c)
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clock24xx.c is missing a omap2_init_clk_clkdm() in its
omap2_clk_init() function. Among other bad effects, this causes the
OMAP hwmod layer to oops on boot.
Thanks to Carlos Aguiar <carlos.aguiar@indt.org.br> and Stefano
Panella <Stefano.Panella@csr.com> for reporting this bug. Thanks to Tony
Lindgren <tony@atomide.com> for N800 booting advice.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Carlos Aguiar <carlos.aguiar@indt.org.br>
Cc: Stefano Panella <Stefano.Panella@csr.com>
Cc: Tony Lindgren <tony@atomide.com>
