Setting CFLAG bits is all well and good but you must sort out ispeed and
ospeed properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring ezusb and whiteheat into line with the coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.
So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.
Longer term we need a proper tty as console abstraction
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to occasional DMA channel hangs observed for I/OAT versions 1.2 and 2.0
a watchdog has been introduced to check every 2 seconds
if all channels progress normally.
If stuck channel is detected, driver resets it.
The reset is done in two parts. The second part is scheduled
by the first one to reinitialize the channel after the restart.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Two small updates to the pcf857x driver: (a) the max732[89] chips are
also second sources for the pcf8574/a, and (b) add a mutex to prevent
trashing the cached state. Adding the lock is effectively a bugfix,
although it seems unlikely that anyone would have run into the issue it
protects against.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maxim's MAX7301 is an SPI GPIO expander with 28 GPIOs. Note: MAX7301's
interrupt feature is not supported yet.
[akpm@linux-foundation.org: coding-style fixes]
[g.liakhovetski@pengutronix.de: Fix inaccuracies in comments, check spi_setup()
return code, mask off high byte in max7301_read()]
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This converts all instances of bus_id in the sparc core kernel to use
either dev_set_name(), or dev_name() depending on the need.
This is done in anticipation of removing the bus_id field from struct
driver.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes vortex_prob1() to handle pci_name() now returning a
constant string.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes the MTD core to handle pci_name() now returning a constant
string.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A driver for the HP iLO/iLO2 management processor, which allows userspace
programs to query the management processor. Programs can open a channel
to the device (/dev/hpilo/dXccbN), and use this to send/receive queries.
The O_EXCL open flag is used to indicate that a particular channel cannot
be shared between processes. This driver will replace various packages
HP has shipped, including hprsm and hp-ilo.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a new sysdev_ext_attribute that stores a pointer to the variable
it manages and some utility functions/macro to easily use them.
Previously all users wrote custom macros to generate show/store
functions for each variable, with this it is possible to avoid
that in many cases.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver core: Suppress sysfs warnings for device_rename().
Renaming network devices to an already existing name is not
something we want sysfs to print a scary warning for, since the
callers can deal with this correctly. So let's introduce
sysfs_create_link_nowarn() which gets rid of the common warning.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
James Bottomley recently discovered that we have
{request,release}_firmware() dummies for the case of the actual
functions not being available and has a fix for the bug that was
actually causing build errors for built-in users with
CONFIG_FW_LOADER=m.
But now missing selects on FW_LOADER are no longer visible at
compile-time at all and can become runtime problems.
FW_LOADER is infrastructure with relatively small codesize we can safely
enable for everyone, and only for people who really need small kernels
(and can be expected to know what they are doing) it matters being able
to disable it.
This patch therefore always sets FW_LOADER=y and allows users only to
disable it with EMBEDDED=y.
As a bonus, we can then get rid of all "select FW_LOADER" plus the due
to it required "depends on HOTPLUG" which removes some complexity from
our Kconfig files.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The systdev_class_register() and sysdev_register() functions have
pr_debug() statements which are enabled when the user selects the
driver core debug. Both of these routines do not produce the
correct output, as they make assumptions about data which has not
been initialised.
In sysdev_class_register() the code uses the kobject_name(&cls->kset.kobj)
at the start of the function, but this is not setup until later in the
same call. Change this to use cls->name which is passed in from the caller.
The sysdev_register() function tries to get the name of the sysdev by
kobject_name(&sysdev->kobj), but that isn't setup until later in the same
function so change this message to use the name of the sysdev's class and
add another message once the name is initialised.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a generic UIO platform driver. It eliminates the need for a
dedicated kernel module for simple platform devices. Users only need to
implement their irq handler in platform code and fill a struct uio_info
there. This helps avoiding code duplication as UIO platform drivers often
share a lot of common code.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes it is necessary to enable/disable the interrupt of a UIO device
from the userspace part of the driver. With this patch, the UIO kernel driver
can implement an "irqcontrol()" function that does this. Userspace can write
an s32 value to /dev/uioX (usually 0 or 1 to turn the irq off or on). The
UIO core will then call the driver's irqcontrol function.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ae210f1886 introduced a big "if UIO"/"endif"
where all uio drivers are defined. So know there is no need for them to
depend explicitly on UIO.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have the dev_printk() variants for this kind of thing, use them
instead of directly trying to access the bus_id field of struct device.
This is done in order to remove bus_id entirely.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no such thing as a "device id size" in the driver core, so
remove the define and fix up any users of this odd define in the rest of
the kernel.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no such thing as a "device name size" in the driver core, so
remove the define and fix up any users of this odd define in the rest of
the kernel.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the lockdep infrastructure in the class core is in place, we
should be able to properly change the internal class semaphore to be a
mutex.
David wrote the original patch, and Greg fixed it up to apply properly
due to all of the recent changes in this area.
From: Dave Young <hidave.darkstar@gmail.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the infrastructure to properly handle lockdep issues when the
internal class semaphore is changed to a mutex.
Matthew wrote the original patch, and Greg fixed it up to work properly
with the class_create() function.
From: Matthew Wilcox <matthew@wil.cx>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes a field that has been deleted, and adds a description fo the
class_dirs field which was previously undocumented.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This renames the struct class "sem" field to be "class_sem" to make
things easier when struct bus_type and struct class merge in the future.
It also makes grepping for fields easier as well.
Based on an idea from Kay.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This renames the struct class "subsys" field to be "class_subsys" to
make things easier when struct bus_type and struct class merge in the
future. It also makes grepping for fields easier as well.
Based on an idea from Kay.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This renames the struct class "interfaces" field to be
"class_interfaces" to make things easier when struct bus_type and struct
class merge in the future. It also makes grepping for fields easier as
well.
Based on an idea from Kay.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This renames the struct class "devices" field to be "class_devices" to
make things easier when struct bus_type and struct class merge in the
future. It also makes grepping for fields easier as well.
Based on an idea from Kay.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the portions of struct class that are dynamic (kobject and
lock and lists) out of the main structure and into a dynamic, private,
structure.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This object really should be a struct device, or at least contain a
pointer to a struct device, as it is trying to create a separate device
tree outside of the main device tree. This patch fixes this problem.
It is needed for the class core rework that is being done in the driver
core.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pointer really is a struct ib_device, not a struct device, so name
it properly to help prevent confusion.
This makes the followon patch in this series much smaller and easier to
understand as well.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This mirrors the functionality that driver_find_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This mirrors the functionality that driver_for_each_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Keep the device_create_drvdata macro around to make merges easier.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more users of this, and it is racy. Use
device_create_drvdata() or device_create_vargs() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch over to use the shiny new device_create_drvdata() call
instead of the original device_create() calls, so this continues
to work after device_create() is removed.
Note that this driver never had the race which motivated removing
the original call; it locked correctly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Ben Collins <ben.collins@ubuntu.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Why?:
There are occasions where userspace would like to access sysfs
attributes for a device but it may not know how sysfs has named the
device or the path. For example what is the sysfs path for
/dev/disk/by-id/ata-ST3160827AS_5MT004CK? With this change a call to
stat(2) returns the major:minor then userspace can see that
/sys/dev/block/8:32 links to /sys/block/sdc.
What are the alternatives?:
1/ Add an ioctl to return the path: Doable, but sysfs is meant to reduce
the need to proliferate ioctl interfaces into the kernel, so this
seems counter productive.
2/ Use udev to create these symlinks: Also doable, but it adds a
udev dependency to utilities that might be running in a limited
environment like an initramfs.
3/ Do a full-tree search of sysfs.
[kay.sievers@vrfy.org: fix duplicate registrations]
[kay.sievers@vrfy.org: cleanup suggestions]
Cc: Neil Brown <neilb@suse.de>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Reviewed-by: SL Baur <steve@xemacs.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Mark Lord <lkml@rtr.ca>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The offb driver already has a collection of hacks to be able to set
the palette on various chips. This adds support for r5xx/r6xx radeons.
This is needed as offb is the only console solution on these currently
and the firmware in some cases sets a really bad color palette. This
fixes using some Radeon X16xx on the Powerstation for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If correctable error occurs the syndrome code was logged as 0. This patch
lets EDAC to log a correct syndrome code to make problem investigation
easier.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add sub match id for ps3 system bus so that two different system bus
devices can be connected to a shared device.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (100 commits)
usb-storage: revert DMA-alignment change for Wireless USB
USB: use reset_resume when normal resume fails
usb_gadget: composite cdc gadget fault handling
usb gadget: minor USBCV fix for composite framework
USB: Fix bug with byte order in isp116x-hcd.c fio write/read
USB: fix double kfree in ipaq in error case
USB: fix build error in cdc-acm for CONFIG_PM=n
USB: remove board-specific UP2OCR configuration from pxa27x-udc
USB: EHCI: Reconciling USB register differences on MPC85xx vs MPC83xx
USB: Fix pointer/int cast in USB devio code
usb gadget: g_cdc dependso on NET
USB: Au1xxx-usb: suspend/resume support.
USB: Au1xxx-usb: clean up ohci/ehci bus glue sources.
usbfs: don't store bad pointers in registration
usbfs: fix race between open and unregister
usbfs: simplify the lookup-by-minor routines
usbfs: send disconnect signals when device is unregistered
USB: Force unbinding of drivers lacking reset_resume or other methods
USB: ohci-pnx4008: I2C cleanups and fixes
USB: debug port converter does not accept more than 8 byte packets
...
This patch (as1110) reverts an earlier patch meant to help with
Wireless USB host controllers. These controllers can have bulk
maxpacket values larger than 512, which puts unusual constraints on
the sizes of scatter-gather list elements. However it turns out that
the block layer does not provide the support we need to enforce these
constraints; merely changing the DMA alignment mask doesn't help.
Hence there's no reason to keep the original patch. The Wireless USB
problem will have to be solved a different way.
In addition, there is a reason to get rid of the earlier patch. By
dereferencing a pointer stored in the ep_in array of struct
usb_device, the current code risks an invalid memory access when it
runs concurrently with device removal. The members of that array are
cleared before the driver's disconnect method is called, so it should
not try to use them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1109b) makes USB-Persist more resilient to errors. With
the current code, if a normal resume fails, it's an unrecoverable
error. With the patch, if a normal resume fails (and if the device is
enabled for USB-Persist) then a reset-resume is tried.
This fixes the problem reported in Bugzilla #10977.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These two fixes ensure the new "CDC Composite Device" gadget
fails cleanly when it's loaded on hardware that can't support
this particular gadget driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fill in a reserved/unused device qualifier field to ensure that
the USBCV tests will always pass.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
URB payload data are transfered in wrong byte order on a big endinan
architecture (AVR32).
Signed-off-by: Julien May <mailinglist@miromico.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in the error case the ipaq driver leaves a dangling pointer to already
freed memory that will be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's the fix. cdc-wdm has the same problem. The fix is the same.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the board-specific UP2OCR configuration from the
pxa27x-udc driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A couple of USB register initializations had to be changed on MPC85xx
platforms. This is due to the internal SoC buses being different on
MPC83xx SoCs vs MPC85xx SoCs.
We currently handle this via an ifdef since 83xx and 85xx are mutually
exclusive kernel builds.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix pointer/int cast in USB devio code, and thus avoid a compiler warning.
A void* data argument passed to bus_find_device() and thence to match_devt()
is used to carry a 32-bit datum. However, casting directly between a u32 and
a pointer is not permitted - there must be an intermediate cast via (unsigned)
long.
This was introduced by the following patch:
commit 94b1c9fa060ece2c8f080583beb6cc6008e41413
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Tue Jun 24 14:47:12 2008 -0400
usbfs: simplify the lookup-by-minor routines
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Copy the OHCI/EHCI PM callbacks of the PCI implementation since
they work equally well on Au1xxx hardware.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Fold multiple probe/remove callbacks into one function;
- minor style fixes, no functional changes.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1107) fixes a small bug in the usbfs registration and
unregistration code. It avoids leaving an error value stored in the
device's usb_classdev field and it avoids trying to unregister a NULL
pointer. (It also fixes a rather extreme overuse of whitespace.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1106) fixes a race between opening and unregistering
device files in usbfs. The current code drops its reference to the
device and then reacquires it, ignoring the possibility that the
device structure might have been removed in the meantime. It also
doesn't check whether the device is already in the NOTATTACHED state
when the file is opened.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB device files are accessible in two ways: as files in usbfs and as
character device nodes. The two paths are supposed to behave
identically, but they don't. When the underlying USB device is
unplugged, disconnect signals are sent to processes with open usbfs
files (if they requested these signals) but not to processes with open
device node files.
This patch (as1104) fixes the bug by moving the disconnect-signalling
code into a common subroutine which is called from both paths.
Putting this subroutine in devio.c removes the only out-of-file
reference to struct dev_state, and so the structure's declaration can
be moved from usb.h into devio.c.
Finally, the new subroutine performs one extra action: It kills all
the outstanding async URBs. (I'd kill the outstanding synchronous
URBs too, if there was any way to do it.) In the past this hasn't
mattered much, because devices were unregistered from usbfs only
when they were disconnected. But now the unregistration can also
occur whenever devices are unbound from the usb_generic driver. At
any rate, killing URBs when a device is unregistered from usbfs seems
like a good thing to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1024) takes care of a FIXME issue: Drivers that don't
have the necessary suspend, resume, reset_resume, pre_reset, or
post_reset methods will be unbound and their interface reprobed when
one of the unsupported events occurs.
This is made slightly more difficult by the fact that bind operations
won't work during a system sleep transition. So instead the code has
to defer the operation until the transition ends.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various cleanups and fixes to the i2c code in ohci-pnx4008:
* Delete empty isp1301_command. The i2c driver command implementation
is optional, so there's no point in providing an empty
implementation.
* Give a name to isp1301_driver. I'm surprised that i2c-core accepted
to register this driver at all. I've chosen "isp1301_pnx" as the
name, because it's not a generic ISP1301 driver (much like the
isp1301_omap driver.) We might want to make the name even more
specific (but "isp1301_ohci_pnx4008" doesn't fit.)
* The ISP1301 is definitely not a hardware monitoring device.
* Fix a memory leak on failure in isp1301_attach. If
i2c_attach_client fails, the client is not registered so
isp1301_detach is never called and the i2c_client memory is lost.
* Use strlcpy instead of strcpy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB debug port only supports 8 byte rx/tx packets. Although spec implies that
"if a packet larger than eight bytes is received from the remote computer, the
device must break the larger packet into eight-byte packets before sending the
data to the Debug Port", the real PLX NET20DC device does not handle it right -
data is corrupted on debug port end if serial interface sends >8 byte urbs.
Patch below fixes the issue by limiting tx urb to 8 byte.
Signed off by: Aleks Gorelov <dared1st@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm must give up secondary interfaces if the primary is disconnected
and vice versa. This wasn't done correctly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial decrements the pm counter even if an interface has been
disconnected. If it was a logical disconnect the interface may belong
already to another driver. This patch introduces a check for disconnected
interfaces.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch saves power for cdc-acm devices that support remote wakeup
while the device is connected.
- request needs_remote_wakeup when needed
- delayed write while a device is autoresumed
- the device is marked busy when appropriate
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 28xb, as documented in comments, has the same ID's as the 28x.
Remove the duplicated ID's from the device tables, and expand the
comment to document this.
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the problem that did not set IRQF_TRIGGER_ flag.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch renames the existing usb_reset_device in hub.c to
usb_reset_and_verify_device and renames the existing
usb_reset_composite_device to usb_reset_device. Also the new
usb_reset_and_verify_device does't need to be EXPORTED .
The idea of the patch is that external interface driver
should warn the other interfaces' driver of the same
device before and after reseting the usb device. One interface
driver shoud call _old_ usb_reset_composite_device instead of
_old_ usb_reset_device since it can't assume the device contains
only one interface. The _old_ usb_reset_composite_device
is safe for single interface device also. we rename the two
functions to make the change easily.
This patch is under guideline from Alan Stern.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
fix the following sparse warning:
drivers/usb/serial/usb-serial.c:927:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/usb-serial.c:927:43: expected unsigned int *minor
drivers/usb/serial/usb-serial.c:927:43: got int *<noident>
CHECK drivers/usb/serial/generic.c
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for hardware configurations that don't match the
chip default register settings (e.g., 16-bit data bus, DACK and
DREQ pulled up instead of down, analog overcurrent mode).
These settings are passed in via the OF device tree. The PCI
interface still assumes the same default values.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is the usb interface driver probe() methods that
can't call usb_set_configuration, not usb device driver.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1103) changes the iteration in the USB scatter-gather to
use a standard SG iterator. Otherwise the iteration will fail if it
encounters a chained SG list.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From the current implementation of usb_reset_composite_device
function, the iface parameter is no longer useful. This function
doesn't do something special for the iface usb_interface,compared
with other interfaces in the usb_device. So remove the parameter
and fix the related caller.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove an explicit memset(.., 0, ...) to a variable allocated with kzalloc
(i.e. 'card_info' array of the structure 'instance').
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fixes an error with filling out control requests
- increases grepability and error logging
- fixes the short read code path
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mark this array as const because it is read-only
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark the tables as const so that they end up in .rodata
section and don't cacheline share with things that get
written to.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
General cleanup on ir-usb module. Introduced
a common header that could be used also on
usb gadget framework.
Lot's of cleanups and now using macros from the header
file.
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes some performance bugs observed with some workloads
when unlinking EHCI queue header (QH) descriptors from the async ring
(control/bulk schedule).
The mechanism intended to defer unlinking an empty QH (so there is no
penalty in common cases where it's quickly reused) was not working as
intended. Sometimes the unlink was scheduled:
- too quickly ... which can be a *strong* negative effect, since
that QH becomes unavailable for immediate re-use;
- too slowly ... wasting DMA cycles, usually a minor issue except
for increased bus contention and power usage;
Plus there was an extreme case of "too slowly": a logical error in the
IAA watchdog-timer conversion meant that sometimes the unlink never
got scheduled.
The fix replaces a simple counter with a timestamp derived from the
controller's 8 KHz microframe counter, and adjusts the timer usage
for some issues associated with HZ being less than 8K.
(Based on a patch originally by Alan Stern, and good troubleshooting
from Leonid.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't allow hubs on the 7th tier as they would allow
devices on the 8th tier.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we do rmmod ohci_hcd while an application is doing something, the
following may happen:
- a control URB completes (in finish_urb) and the ohci's endpoint is
set into ED_UNLINK in ed_deschedule
- same URB is (re)submitted because of the open/close loop or other
such application behaviour
- rmmod sets the state to HC_STATE_QUESCING
- finish_unlinks happens at next SOF; normally it would set ed into
ED_IDLE and immediately call ed_schedule (since URB had extra TDs
queued), which sets it into ED_OPER. But the check in ed_schedule
makes it fail with -EAGAIN (which is ignored)
- from now on we have a dead URB stuck; it cannot even be unlinked
because the ed status is not ED_OPER, and thus start_ed_unlink is
not invoked.
This patch removes the check. In 2.6.25, all callers check for
__ACTIVE bit before invoking ed_schedule, which is more appropriate.
Alan Stern and David Brownell approved of this (cautiously).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As RMK pointed out, considering the fact that the _only_ platform with
a PXA and SA1111 is the Lubbock, and that SA1111 DMA doesn't work there,
(i.e. the SA1111 OHCI doesn't work there) the SA1111 OHCI driver should
really be made SA11x0 specific.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like usb_put_hcd was missing. Also, make an always-zero function
return void.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i is used only as a for-loop index no need to declare another.
drivers/usb/atm/speedtch.c:832:7: warning: symbol 'i' shadows an earlier one
drivers/usb/atm/speedtch.c:766:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The get/set 2101_config helpers take an unsigned int rather than an
int. It is safe to change these in each case and may even produce
better code as it will be an unsigned divide rather than a signed
divide in places. All other manipulation was setting/masking bits
which will not be affected by the sign change.
Fixes the following sparse warnings:
drivers/usb/serial/cp2101.c:378:44: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:378:44: expected unsigned int *data
drivers/usb/serial/cp2101.c:378:44: got int *<noident>
drivers/usb/serial/cp2101.c:388:40: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:388:40: expected unsigned int *data
drivers/usb/serial/cp2101.c:388:40: got int *<noident>
drivers/usb/serial/cp2101.c:413:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:413:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:413:42: got int *<noident>
drivers/usb/serial/cp2101.c:421:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:421:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:421:42: got int *<noident>
drivers/usb/serial/cp2101.c:444:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:444:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:444:42: got int *<noident>
drivers/usb/serial/cp2101.c:451:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:451:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:451:42: got int *<noident>
drivers/usb/serial/cp2101.c:458:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:458:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:458:42: got int *<noident>
drivers/usb/serial/cp2101.c:471:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:471:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:471:42: got int *<noident>
drivers/usb/serial/cp2101.c:481:42: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:481:42: expected unsigned int *data
drivers/usb/serial/cp2101.c:481:42: got int *<noident>
drivers/usb/serial/cp2101.c:561:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:561:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:561:41: got int *<noident>
drivers/usb/serial/cp2101.c:591:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:591:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:591:45: got int *<noident>
drivers/usb/serial/cp2101.c:597:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:597:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:597:41: got int *<noident>
drivers/usb/serial/cp2101.c:608:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:608:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:608:45: got int *<noident>
drivers/usb/serial/cp2101.c:614:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:614:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:614:41: got int *<noident>
drivers/usb/serial/cp2101.c:623:45: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:623:45: expected unsigned int *data
drivers/usb/serial/cp2101.c:623:45: got int *<noident>
drivers/usb/serial/cp2101.c:680:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:680:50: expected unsigned int *data
drivers/usb/serial/cp2101.c:680:50: got int *<noident>
drivers/usb/serial/cp2101.c:690:43: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:690:43: expected unsigned int *data
drivers/usb/serial/cp2101.c:690:43: got int *<noident>
drivers/usb/serial/cp2101.c:715:41: warning: incorrect type in argument 3 (different signedness)
drivers/usb/serial/cp2101.c:715:41: expected unsigned int *data
drivers/usb/serial/cp2101.c:715:41: got int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is another case where the lock_kernel appears to be unneccessary and
could be removed with a bit more investigative work
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The BKL is actually probably not needed as the mutex seems sufficient. If
so then a further patch to drop it would be a good followup.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm pretty sure the mutex is sufficient for all locking but will come
back to that later if the USB folks don't beat me to it. For now get rid
of the old BKL ioctl method and wrap the ioctl handler
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm pretty sure this can be eliminated however I couldn't prove (or find)
what stopped the device vanishing mid IOCTL_GET_HARD_VERSION. Perhaps a
USB wizard could double check that and see if the lock_kernel can go
entirely.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi has one ioctl, which is buggy and for debugging. Kill it off
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This keeps the gadget ioctl method wrapped but pushes the BKL down into
the gadget code so we can use unlocked_ioctl().
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Building on the previous patches which took code from this driver and
pakaged it in more-reusable network "function" components, this patch
gets rid of the original code and uses those components instead.
As seen with the other gadget driver conversions, the resulting code
is much easier to understand and (presumably) work with. In this case
that's especially true, since the Ethernet gadget had grown to handle
three (!) different Ethernet-over-USB protocols. This modularization
should make it much easier to add a fourth option for the newish CDC
"Ethernet Emulation Model" (or EEM).
Lightly tested, primarily at full speed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a simple example of a composite gadget, combining two
Communications Class Device (CDC) functions: ECM and ACM.
This provides a clear example of how the composite gadget framework
is intended to work. It's surprising that MS-Windows (or at least,
XP and previous) won't "just work" with something this simple...
One /proc/bus/usb/devices listing looks like:
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 46 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0525 ProdID=a4aa Rev= 3.01
S: Manufacturer=Linux 2.6.26-rc6-pnut with net2280
S: Product=CDC Composite Gadget
C:* #Ifs= 4 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Not all USB peripheral controller hardware can support this driver.
All the highspeed-capable peripheral controllers with drivers now in
the mainline kernel seem to support this, as does omap_udc. But
many full speed controllers don't have enough endpoints, or (as with
the PXA controllers) don't support altsettings.
Lightly tested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a RNDIS function driver, extracted from the all-in-one
Ethernet gadget driver.
Lightly tested ... there seems to be a pre-existing problem when
talking to Windows XP SP2, not quite sure what's up with that yet.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a "CDC Ethernet" (ECM) function driver, extracted from the
all-in-one Ethernet gadget driver.
This is a good example of how to implement interface altsettings.
In fact it's currently the only such example in the gadget stack,
pending addition of OBEX support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a simple "CDC Subset" (and MCCI "SAFE") function driver, extracted
from the all-in-one Ethernet gadget driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract the peripheral side Ethernet-over-USB link layer code from
the all-in-one Ethernet gadget driver into a component that can be
called by various functions, so the various flavors can be split
apart and selectively reused.
A notable difference from the approach taken with the serial link
layer code (beyond talking to NET not TTY) is that because of the
initialization requirements, this only supports one network link.
(And one set of Ethernet link addresses.)
That is, each configuration may have only one instance of a network
function. This doesn't change behavior; the current code has that
same restriction. If you want multiple logical links, that can
easily be done using network layer tools.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some cleanup to the RNDIS code:
- Minor bugfix: rndis_unit() is supposed to put the link into the
RNDIS_UNINITIALIZED state, which does not mean "unused". There's
a separate method to stop using the link. (Bug doesn't affect
anything right now because of how the code is used.)
- Reduce coupling between RNDIS code and its user(s), in preparation
for updates in that code:
* Decouple RNDIS_RESPONSE_AVAILABLE notifications from net_device
by passing just a void* handle. (Also, remove the unused return
value of the notification callback.)
* When it needs a copy of net_device stats, just ask for it
- Remove unused/untested code backing various never-used OIDs:
* RNDIS_PM, RNDIS_WAKEUP ... "should" get implemented, but the
relevant docs were unclear, ambguous, and incomplete. Someone
with access to the Hidden Gospels (maybe in the EU?) might be
able to figure out what this should do.
* RNDIS_OPTIONAL_STATS ... as the name suggests, optional. Never
implemented in part because not all the semantics were clear.
* OID_GEN_RNDIS_CONFIG_PARAMETER, which has been #if 0 forever.
- A few small whitespace fixes
Plus switch the VERBOSE symbol over to the newer VERBOSE_DEBUG style.
There should be no functional changes because of this patch; it's a
net source code shrink (because of the dead/unused code removal) and
a small object code shrink (a couple hundred bytes on ARMv5).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This switches the serial gadget over to using the new "function"
versions of the serial port interfacing code. The remaining code
in the main source file is quite small...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split out the generic serial support into a "function driver". This
closely mimics the ACM support, but with a MUCH simpler control model.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split out CDC ACM parts of "gadget serial" to a "function driver".
Some key structural differences from the previous ACM support, shared
with with the generic serial function (next patch):
- As a function driver, it can be combined with other functions.
One gadget configuration could offer both serial and network
links, as an example.
- One serial port can be exposed in multiple configurations;
the /dev/ttyGS0 node could be exposed regardless of which
config the host selected.
- One configuration can expose multiple serial ports, such as
ttyGS0, ttyGS1, ttyGS2, and ttyGS3.
This code should be a lot easier to understand than the previous
all-in-one-big-file version of the driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update Gadget Zero to use the more modular versions of the loopback
and source/sink configuration drivers which build on the new gadget
framework code.
The core code is a LOT simpler, and it should be much easier now to
understand how the parts fit together. The conversion is an overall
source shrink in terms of this gadget, since it uses more midlayer
support. However, it's an overall increase in object size because
there's less sharing between the two configurations (improves code
clarity) and because the midlayer is a bit more functional than this
driver actually needs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This splits the gadget zero "loopback" configuration into a standalone
"configuration driver", building on the composite gadget framework code.
It doesn't yet pull the original code out of gadget zero or update how
that driver is built.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This splits the gadget zero "source/sink" configuration into a standalone
"configuration driver", building on the composite gadget framework code.
It doesn't yet pull the original code out of gadget zero or update how
that driver is built.
Neither this, nor its sibling "loopback" configuration, is a function
driver that can be combined with other functions. (The host "usbtest"
driver wouldn't know how to deal with that!) However the code becomes
simpler because of this conversion, so it's a net win.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add <linux/usb/composite.h> interfaces for composite gadget drivers, and
basic implementation support behind it:
- struct usb_function ... groups one or more interfaces into a function
managed as one unit within a configuration, to which it's added by
usb_add_function().
- struct usb_configuration ... groups one or more such functions into
a configuration managed as one unit by a driver, to which it's added
by usb_add_config(). These operate at either high or full/low speeds
and at a given bMaxPower.
- struct usb_composite_driver ... groups one or more such configurations
into a gadget driver, which may be registered or unregistered.
- struct usb_composite_dev ... a usb_composite_driver manages this; it
wraps the usb_gadget exposed by the controller driver.
This also includes some basic kerneldoc.
How to use it (the short version): provide a usb_composite_driver with a
bind() that calls usb_add_config() for each of the needed configurations.
The configurations in turn have bind() calls, which will usb_add_function()
for each function required. Each function's bind() allocates resources
needed to perform its tasks, like endpoints; sometimes configurations will
allocate resources too.
Separate patches will convert most gadget drivers to this infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Define three new descriptor manipulation utilities, for use when
setting up functions that may have multiple instances:
usb_copy_descriptors() to copy a vector of descriptors
usb_free_descriptors() to free the copy
usb_find_endpoint() to find a copied version
These will be used as follows. Functions will continue to have static
tables of descriptors they update, now used as __initdata templates.
When a function creates a new instance, it patches those tables with
relevant interface and string IDs, plus endpoint assignments. Then it
copies those morphed descriptors, associates the copies with the new
function instance, and records the endpoint descriptors to use when
activating the endpoints. When initialization is done, only the copies
remain in memory. The copies are freed on driver removal.
This ensures that each instance has descriptors which hold the right
instance-specific data. Two instances in the same configuration will
obviously never share the same interface IDs or use the same endpoints.
Instances in different configurations won't do so either, which means
this is slightly less memory-efficient in some cases.
This also includes a bugfix to the epautoconf code that shows up with
this usage model. It must replace the previous endpoint number when
updating the template descriptors, not just mask in a few more bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Teach "gadget serial" to use the new abstracted (and bugfixed) TTY glue,
and remove all the orignal tangled-up code. Update the documentation
accordingly. This is a net object code shrink and cleanup; it should
make it a lot easier to see how the TTY glue should accomodate updates
to the TTY layer, be bugfixed, etc.
Notable behavior changes include: it can now support getty even when
there's no USB connection; it fits properly into the mdev/udev world;
and RX handling is better (throttling works, and low latency).
Configurations with scripts setting up the /dev/ttygserial device node
(with "experimental" major number) may want to change that to be a
symlink pointing to the /dev/ttyGS0 file, as a migration aid; else,
just switch entirely over to mdev/udev.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This abstracts the "gadget serial" driver TTY glue into a separate
component, cleaning it up and disentangling it from connection state.
It also changed some behaviors for the better:
- Stops using "experimental" major #127, and switches over to
having the TTY layer allocate the dev_t numbers.
- Provides /sys/class/tty/ttyGS* nodes, thus mdev/udev support.
(Note "mdev" hotplug bug in Busybox v1.7.2: /dev/ttyGS0 will
be a *block* device without CONFIG_SYSFS_DEPRECATED_V2.)
- The tty nodes no longer reject opens when there's no host.
Now they can support normal getty configs in /etc/inttab...
- Now implements RX throttling. When the line discipline says
it doesn't want any more data, only packets in flight will be
delivered (currently, max 1K/8K at full/high speeds) until it
unthrottles the data.
- Supports low_latency. This is a good policy for all USB serial
adapters, since it eliminates scheduler overhead on RX paths.
This also includes much cleanup including better comments, fixing
memory leaks and other bugs (including some locking fixes), messaging
cleanup, and an interface audit and tightening. This added up to a
significant object code shrinkage, on the order of 20% (!) depending
on CPU and compiler.
A separate patch actually kicks in this new code, using the functions
declared in this new header, and removes the previous glue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out newer versions of the AT91 UDC hardware have increased
sizes of some of the FIFOs. Reporting that is a Good Thing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1092) implements "soft" unbinding for usb-storage. When
the disconnect routine is called, all commands and reset delays are
allowed to complete normally until after scsi_remove_host() returns.
This means that the commands needed for an orderly shutdown will be
sent through to the device.
Unlike before, the driver will now execute every command that it
accepts. Hence there's no need for special code to catch unexecuted
commands and fail them.
The new sequence of events when disconnect runs goes as follows:
If the device is truly unplugged, set the DISCONNECTING
flag so we won't try to access it any more.
If the SCSI-scanning thread hasn't started up yet, prevent
it from doing anything by setting the new DONT_SCAN flag.
Then wake it up and wait for it to terminate.
Remove the SCSI host. This unbinds the upper-level drivers,
doing an orderly shutdown. Commands sent to quiesce the
device will be transmitted normally, unless the device is
unplugged.
Set the DISCONNECTING flag so that we won't accept any new
commands that might get submitted (there aren't supposed to be
any) and we won't try to access the device for resets.
Tell the control thread to exit by waking it up with no
pending command, and wait for it to terminate.
Go on to do all the other normal stuff: releasing resources,
freeing memory, and so on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1091) changes the way usbcore handles interface
unbinding. If the interface's driver supports "soft" unbinding (a new
flag in the driver structure) then in-flight URBs are not cancelled
and endpoints are not disabled. Instead the driver is allowed to
continue communicating with the device (although of course it should
stop before its disconnect routine returns).
The purpose of this change is to allow drivers to do a clean shutdown
when they get unbound from a device that is still plugged in. Killing
all the URBs and disabling the endpoints before calling the driver's
disconnect method doesn't give the driver any control over what
happens, and it can leave devices in indeterminate states. For
example, when usb-storage unbinds it doesn't want to stop while in the
middle of transmitting a SCSI command.
The soft_unbind flag is added because in the past, a number of drivers
have experienced problems related to ongoing I/O after their disconnect
routine returned. Hence "soft" unbinding is made available only to
drivers that claim to support it.
The patch also replaces "interface_to_usbdev(intf)" with "udev" in a
couple of places, a minor simplification.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the following needlessly global functions static:
- enqueue_an_ATL_packet()
- enqueue_an_INT_packet()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1090) converts the one remaining semaphore in
usb-storage into a completion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1089) separates out the dynamic atomic bitflags and the
static bitfields in usb-storage. Until now the two sorts of flags
have been sharing the same word; this has always been awkward.
To help prevent possible confusion, the two new fields each have a
different name from the original. us->fflags contains the fixed
bitfields (mostly taken from the USB ID table in unusual_devs.h), and
us->dflags contains the dynamic atomic bitflags (used with set_bit,
test_bit, and so on).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sort out the insane naming like "OperationalFirmwareVersion" which seems
designed to cause formatting problems and RSI
Merge various common code together
Clean up the pointlessly complex and spread about MCR handling
This is really just the low hanging fruit.
Needs lots of testing before it goes upstream so testers and reports
appreciated
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1083) combines hub_quiesce() and hub_stop() into a
single routine. There's no point keeping them separate since they are
usually called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1071) combines hub_activate() and hub_restart() into a
single routine. There's no point keeping them separate, since they
are always called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1082) makes a small optimization to the way the hub
driver carries out port debouncing immediately after a hub is
activated (i.e., initialized, reset, or resumed). If any port-change
statuses are observed, the code will delay for a minimal debounce
period -- thereby making a good start at debouncing all the ports at
once.
If this wasn't sufficient then khubd will debounce any port that still
requires attention. But in most cases it should suffice; it's rare
for a device to need more than a minimal debounce delay. (In the
cases of hub initialization or reset even that is most likely not
needed, since any devices plugged in at such times have probably been
attached for a while.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1073) adds to khubd a way to recover from power-session
interruption caused by transient connect-change or enable-change
events. After the debouncing period, khubd attempts to do a
USB-Persist-style reset or reset-resume. If it works, the connection
will remain unscathed.
The upshot is that we will be more immune to noise caused by EMI. The
grace period is on the order of 100 ms, so this won't permit recovery
from the "accidentally knocked the USB cable out of its socket" type
of event, but it's a start.
As an added bonus, if a device was suspended when the system goes to
sleep then we no longer need to check for power-session interruptions
when the system wakes up. Khubd will naturally see the status change
while processing the device's parent hub and will do the right thing.
The remote_wakeup() routine is changed; now it expects the caller to
acquire the device lock rather than acquiring the lock itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1081) straightens out the logic of the hub_restart()
routine. Each port of the hub is scanned and the driver makes sure
that ports which are supposed to be disabled really _are_ disabled.
Any ports with a significant change in status are flagged in
hub->change_bits, so that khubd can focus on them without the need to
scan all the ports a second time -- which means the hub->activating
flag is no longer needed.
Also, it is now recognized explicitly that the only reason for
resuming a port which was not suspended is to carry out a reset-resume
operation, which happens only in a non-CONFIG_USB_SUSPEND setting.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Linus's previous patch that is in mainline to make it
easier for the USB hub.c patches that follow this to apply cleanly. The
functionality will be added back in a followon patch in this series.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1080) makes a significant change to the way khubd
handles port connect-change and enable-change events. Both types of
event are now debounced, and the debouncing is carried out _before_ an
existing usb_device is unregistered, instead of afterward.
This means that drivers will have to deal with longer runs of errors
when a device is unplugged, but they are supposed to be prepared for
that in any case.
The advantage is that when an enable-change occurs (caused for example
by electromagnetic interference), the debouncing period will provide
time for the cause of the problem to die away. A simple port reset
(added in a forthcoming patch) will then allow us to recover from the
fault.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1070) creates a new subroutine to check whether a device
can be resumed. This code is needed even when CONFIG_USB_SUSPEND
isn't set, because devices do suspend themselves when the root hub
(and hence the entire bus) is suspended, and power sessions can get
lost during a system sleep even without individual port suspends.
The patch also fixes a loose end in USB-Persist reset-resume handling.
When a low- or full-speed device is attached to an EHCI's companion
controller, the port handoff during resume will cause the companion
port's connect-status-change feature to be set. If that flag isn't
cleared, the port-reset code will think it indicates that the device
has been unplugged and the reset-resume will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Alan's previous patch so that the recent Hub changes will
apply cleanly. The above mentioned patch was needed for 2.6.26 to work
properly.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes usb_create_hcd() to be able to handle the fact that
pci_name() has changed to a constant string.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (25 commits)
mmtimer: Push BKL down into the ioctl handler
[IA64] Remove experimental status of kdump
[IA64] Update ia64 mmr list for SGI uv
[IA64] Avoid overflowing ia64_cpu_to_sapicid in acpi_map_lsapic()
[IA64] adding parameter check to module_free()
[IA64] improper printk format in acpi-cpufreq
[IA64] pv_ops: move some functions in ivt.S to avoid lack of space.
[IA64] pvops: documentation on ia64/pv_ops
[IA64] pvops: add to hooks, pv_time_ops, for steal time accounting.
[IA64] pvops: add hooks, pv_irq_ops, to paravirtualized irq related operations.
[IA64] pvops: add hooks, pv_iosapic_ops, to paravirtualize iosapic.
[IA64] pvops: define initialization hooks, pv_init_ops, for paravirtualized environment.
[IA64] pvops: paravirtualize NR_IRQS
[IA64] pvops: paravirtualize entry.S
[IA64] pvops: paravirtualize ivt.S
[IA64] pvops: paravirtualize minstate.h.
[IA64] pvops: define paravirtualized instructions for native.
[IA64] pvops: preparation for paravirtulization of hand written assembly code.
[IA64] pvops: introduce pv_cpu_ops to paravirtualize privileged instructions.
[IA64] pvops: add an early setup hook for pv_ops.
...
I was looking at this out of interest, but I'm in no way familiar with
the code.
Looks to me that the error handling code in mac80211_hwsim is awkward.
Which leads to it calling ieee80211_unregister_hw even when
ieee80211_register_hw failed.
The function has a for loop where it generates all simulated radios.
when something fails, the error handling will call mac80211_hwsim_free
which frees all simulated radios who's pointer isn't zero. However the
information stored is insufficient to determine whether or not the call
to ieee80211_register_hw succeeded or not for a specific radio. The
included patch makes init_mac80211_hwsim clean up the current simulated
radio, and then calls into mac80211_hwsim_free to clean up all the
radios that did succeed.
This however doesn't explain why the rate control registration failed..
build tested this, but had some problems reproducing the original
problem.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netfilter: nf_conntrack_sctp: fix sparse warnings
netfilter: nf_nat_sip: c= is optional for session
netfilter: xt_TCPMSS: collapse tcpmss_reverse_mtu{4,6} into one function
netfilter: nfnetlink_log: send complete hardware header
netfilter: xt_time: fix time's time_mt()'s use of do_div()
netfilter: accounting rework: ct_extend + 64bit counters (v4)
netlink: add NLA_PUT_BE64 macro
netfilter: nf_nat_core: eliminate useless find_appropriate_src for IP_NAT_RANGE_PROTO_RANDOM
hdlcdrv: Fix CRC calculation.
Revert "pkt_sched: Make default qdisc nonshared-multiqueue safe."
net: In __netif_schedule() use WARN_ON instead of BUG_ON
net: Improve simple_tx_hash().
pkt_sched: Remove unused variable skb in dev_deactivate_queue function.
sunhme: Remove stop/wake TX queue calls in set-multicast-list handler.
ucc_geth: do not touch net queue in adjust_link phylib callback
gianfar: do not touch net queue in adjust_link phylib callback
atl1: Do not wake queue before queue has been started.
Fix kernel-doc comments so that they don't produce errors.
Also cut some extraneous copy-paste text.
Error(linhead//drivers/pci/pci.c:1133): duplicate section name 'Description'
Error(linhead//drivers/pci/pci.c:1189): duplicate section name 'Description'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (160 commits)
x86: remove extra calling to get ext cpuid level
x86: use setup_clear_cpu_cap() when disabling the lapic
KVM: fix exception entry / build bug, on 64-bit
x86: add unknown_nmi_panic kernel parameter
x86, VisWS: turn into generic arch, eliminate leftover files
x86: add ->pre_time_init to x86_quirks
x86: extend and use x86_quirks to clean up NUMAQ code
x86: introduce x86_quirks
x86: improve debug printout: add target bootmem range in early_res_to_bootmem()
Subject: devmem, x86: fix rename of CONFIG_NONPROMISC_DEVMEM
x86: remove arch_get_ram_range
x86: Add a debugfs interface to dump PAT memtype
x86: Add a arch directory for x86 under debugfs
x86: i386: reduce boot fixmap space
i386/xen: add proper unwind annotations to xen_sysenter_target
x86: reduce force_mwait visibility
x86: reduce forbid_dac's visibility
x86: fix two modpost warnings
x86: check function status in EDD boot code
x86_64: ia32_signal.c: remove signal number conversion
...
* 'for-linus' of git://neil.brown.name/md: (52 commits)
md: Protect access to mddev->disks list using RCU
md: only count actual openers as access which prevent a 'stop'
md: linear: Make array_size sector-based and rename it to array_sectors.
md: Make mddev->array_size sector-based.
md: Make super_type->rdev_size_change() take sector-based sizes.
md: Fix check for overlapping devices.
md: Tidy up rdev_size_store a bit:
md: Remove some unused macros.
md: Turn rdev->sb_offset into a sector-based quantity.
md: Make calc_dev_sboffset() return a sector count.
md: Replace calc_dev_size() by calc_num_sectors().
md: Make update_size() take the number of sectors.
md: Better control of when do_md_stop is allowed to stop the array.
md: get_disk_info(): Don't convert between signed and unsigned and back.
md: Simplify restart_array().
md: alloc_disk_sb(): Return proper error value.
md: Simplify sb_equal().
md: Simplify uuid_equal().
md: sb_equal(): Fix misleading printk.
md: Fix a typo in the comment to cmd_match().
...
This is a trivial patch against the hdlcdrv module that fixes its CRC
calculation. The finished CRC was overwriting the first two bytes of
each packet rather than being appended to the end.
I've tested this with 2.6.8 and 2.6.10-rc1, but hdlcdrv hasn't changed
much recently so it should work with many other kernel versions.
Signed-off-by: Micah Dowty <micah@navi.cx>
Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits b02f5ad6a3 ("istallion: use
tty_port") and a352def21a ("tty: Ldisc
revamp") broke the istallion driver.
Fix the compile error and silence a warning.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based upon a bug report by Alexander Beregalov and commentary
from Ben Hutchings.
These are totally unnecessary, in particular because this
driver's ->hard_start_xmit() handler takes the same driver
spinlock that the set-multicast-list handler uses.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Alexey Dobriyan, the patch is
also tested by him and confirmed to fix the problem.
Packet flow during link state events should not be done by
waking and stopping the TX queue anyways, that is handled
transparently by netif_carrier_{on,off}().
So, remove the netif_{wake,stop}_queue() calls in the link
check code, and add the necessary netif_start_queue() call
to atl1_up().
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements biovec merge function for crypt target.
If the underlying device has merge function defined, call it.
If not, keep precomputed value.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove max_sector restriction - merge function replaced it.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch implements biovec merge function for linear target.
If the underlying device has merge function defined, call it.
If not, keep precomputed value.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce a bvec merge function for device mapper devices
for dynamic size restrictions.
This code ensures the requested biovec lies within a single
target and then calls a target-specific function to check
against any constraints imposed by underlying devices.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change snapshot per-module mempool to per-device mempool.
Per-module mempools could cause a deadlock if multiple
snapshot devices are stacked above each other.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a race condition that returns incorrect data when a write causes an
exception to be allocated whilst a read is still in flight.
The race condition happens as follows:
* A read to non-reallocated sector in the snapshot is submitted so that the
read is routed to the original device.
* A write to the original device is submitted. The write causes an exception
that reallocates the block. The write proceeds.
* The original read is dequeued and reads the wrong data.
This race can be triggered with CFQ scheduler and one thread writing and
multiple threads reading simultaneously.
(This patch relies upon the earlier dm-kcopyd-per-device.patch to avoid a
deadlock.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Whenever a snapshot read gets mapped through to the origin, track it in
a per-snapshot hash table indexed by chunk number, using memory allocated
from a new per-snapshot mempool.
We need to track these reads to avoid race conditions which will be fixed
by patches that follow.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Return a specific error message if there are an invalid number of multipath
arguments.
This invalid command returns an "Unknown error" because the ti->error field is
not set
dmsetup create --table '0 2 multipath 0 0 1 1 round-robin 0 1 1 /dev/sdh' mpath0
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm_dirty_log_{init,exit}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Free path selector if the arguments are invalid.
This command (note that it is invalid) causes reference leak on module
"dm_round_robin" and prevents the module from being removed.
dmsetup create --table '0 2 multipath 0 0 1 1 round-robin /dev/sdh' mpath0
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
All modifications and most access to the mddev->disks list are made
under the reconfig_mutex lock. However there are three places where
the list is walked without any locking. If a reconfig happens at this
time, havoc (and oops) can ensue.
So use RCU to protect these accesses:
- wrap them in rcu_read_{,un}lock()
- use list_for_each_entry_rcu
- add to the list with list_add_rcu
- delete from the list with list_del_rcu
- delay the 'free' with call_rcu rather than schedule_work
Note that export_rdev did a list_del_init on this list. In almost all
cases the entry was not in the list anymore so it was a no-op and so
safe. It is no longer safe as after list_del_rcu we may not touch
the list_head.
An audit shows that export_rdev is called:
- after unbind_rdev_from_array, in which case the delete has
already been done,
- after bind_rdev_to_array fails, in which case the delete isn't needed.
- before the device has been put on a list at all (e.g. in
add_new_disk where reading the superblock fails).
- and in autorun devices after a failure when the device is on a
different list.
So remove the list_del_init call from export_rdev, and add it back
immediately before the called to export_rdev for that last case.
Note also that ->same_set is sometimes used for lists other than
mddev->list (e.g. candidates). In these cases rcu is not needed.
Signed-off-by: NeilBrown <neilb@suse.de>
Open isn't the only thing that increments ->active. e.g. reading
/proc/mdstat will increment it briefly. So to avoid false positives
in testing for concurrent access, introduce a new counter that counts
just the number of times the md device it open.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Also, change the type of the size parameter from unsigned long long to
sector_t and rename it to num_sectors.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The checks in overlaps() expect all parameters either in block-based
or sector-based quantities. However, its single caller passes two
rdev->data_offset arguments as well as two rdev->size arguments, the
former being sector counts while the latter are measured in 1K blocks.
This could cause rdev_size_store() to accept an invalid size from user
space. Fix it by passing only sector-based quantities to overlaps().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
- used strict_strtoull in place of simple_strtoull
- use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
- don't adjust mddev->size to fit, rather reject changes which make
rdev->size smaller than mddev->size
Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing. But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that. The previous way invites confusion.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: let asic3 use mem resource instead of bus_shift
mfd: remove DS1WM register definitions from asic3.h
mfd: add ASIC3_CONFIG_GPIO templates
mfd: fix the asic3 irq demux code
mfd: asic3 should depend on gpiolib
mfd: fix asic3 config array initialisation
mfd: move asic3 probe functions into __init section
mfd: Use uppercase only for asic3 macros and defines
mfd: use dev_* macros for asic3 debugging
mfd: New asic3 gpio configuration code
mfd: asic3 children platform data removal
mfd: asic3 gpiolib support
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
Looking at older kernel sources the APOLLO_ELPLUS option was added
somewhere during kernel 2.1, but even kernel 2.2.0 does not contain
any driver that would be enabled through it...
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register the Atari-specific video modes with sysfs, so you can see them in
/sys/class/graphics/fb0/modes and change the video mode by writing to
/sys/class/graphics/fb0/mode.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
