This patch adds the Intel ICH9M RAID controller DID for SATA support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conditionalize all PM related stuff in libata core layer using
CONFIG_PM.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some LLDs were missing scsi device PM callbacks while having host/port
suspend support. Add missing ones.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The QDI init code contains some bugs which mean it only works if you have
a test setup that causes both a successful and failed probe. Fix this
Found by Philip Guo
(Who found it working on code analysis tools not running VLB IDE
controllers)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox noticed several hooks in pata_* drivers were missing, when
he authored his ->cable_detect hook patches. This patch extracts
just those fixes from Alan's patches, adding the necessary hooks
(usually ->freeze, ->thaw, and ->post_internal_cmd) to the drivers.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2.6.21-rc has horrible problems with libata and PATA cable types (and
thus speeds). This occurs because Tejun fixed a pile of other bugs and
we now do cable detect enforcement for drive side detection properly.
Unfortunately we don't do the process around cable detection right. Tejun
identified the problem and pointed to the right Annex in the spec, this patch
implements the needed changes.
The basic requirement is that we have to identify the slave before the
master.
The patch switches the identify order so that we can do the drive side
detection correctly.
[NOTE: patch and description extracted from a larger work written
and signed-off-by Alan Cox]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The initial simplex handling code is fooled if you suspend and resume.
This also causes problems with some single channel controllers which
claim to be simplex.
The fix is fairly simple, instead of keeping a flag to remember if we
gave away the simplex channel we remember the actual owner. As the owner
is always part of the host_set we don't even need a refcount.
Knowing the owner also means we can reassign simplex DMA channels in
future hotplug code etc if we need to
Signed-off-by: Alan Cox <alan@redhat.com>
(and a signed-off for the patch I sent before while I remember)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spurious SDB FIS during NCQ might not contain spurious completions.
It could be spurious TF update or invalid async notification. Treat
as HSM violation iff a spurious SDB FIS contains spurious completions;
otherwise, just whine once about it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make jmiron_ata quirk update pdev->class after programming the device
and update ahci and pata_jmicron such that they match class code
instead of checking function number manually. For ahci, it matches
for vendor and class. For pata_jmicron, it matches vendor, device and
class as IDE class isn't as well defined as AHCI class.
This makes jmicron device matching more conventional and script
friendly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Channel redirect and AHCI mode enable programmings are done via PCI
quirk for both probe and resume paths. Drop duplicate and possibly
unsafe device programming from pata_jmicron().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Blacklist FUJITSU MHT2060BH for NCQ. On this drive, NCQ works iff
queue depth is equal to or less than 4. Just turn it off.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mike Accetta <maccetta@laurelnetworks.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill unused local variable idx in sil24_fill_sg().
Spotted by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clearing drvdata in ->remove_one causes NULL pointer deference. Clear
drvdata only in ata_host_release() after all resources are freed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IRQ mask bits assumed a 60xx or newer generation chip, which is very
wrong for the 50xx series. Luckily both generations shared the per-port
interrupt mask bits, leaving only the "misc chip features" bits to be
completely mismatched.
Fix 50xx by ensuring we only program bits that exist.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code in mv_edma_cfg() reflected its 60xx origins, by doing things
[slightly] incorrectly on the older 50xx and newer 6042/7042 chips.
Clean up the EDMA configuration setup such that, each chip family
carefully initializes its own EDMA setup.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Manuel Lass reports:
> This bug is also present in 2.6.21-rc1, and this patch
> indeed fixes it.
The change to the devres layer re-orders the execution of cleanup
functions and in turn causes the pcmcia layer to oops as it zaps a
pointer now needed later on. We simply leave the pointer alone.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Also export dev_disable as this is needed by drivers doing slave decode
filtering, which will follow shortly
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Each place in pdc_ata_init_one() that initialises a SATA
port first calls pdc_ata_setup_port(), and then manually
assigns the port's ->scr_addr. Simplify the code by extending
pdc_ata_setup_port() to also handle scr_addr initialisation;
for PATA ports we pass NULL as scr_addr.
The initialisation of the PATA-only 20619 redundantly set
up scr_addr for the ports. Remove this.
Tested on 20619, 20575, and 20775 chips.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When I merged my 20619 new EH conversion with #libata-upstream
I had to manually resolve a conflict, and inadvertently lost
pdc_pata_ops' ->post_internal_cmd binding. Corrected by this patch.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All drivers must implement this hook, otherwise ATA commands would go
nowhere (and a lot of other oopsen would appear as well).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate sata_vsc interrupt handling into a normal (per-port) path and an
error path with the addition of vsc_port_intr and vsc_error_intr
respectively. The error path handles interrupt based
hotplug events which requires the definition of vsc_freeze and vsc_thaw.
Note: vsc_port_intr has a workaround for unexpected interrupts that occur
during polled commands. This fixes a regression between 2.6.19 and 2.6.20.
Changes in take2:
* removed definition of invalid fis bit
* let standard ata-error-handling handle the serror register
* clear all unhandled interrupts
* revert changes to vsc_intr_mask_update (vsc_thaw enables all interrupts)
* use unlikely() for the pci-abort and not-our-interrupt cases in vsc_sata_interrupt
Changes in take3:
* Unify the "add" + "hook-up" patches into this single patch
[htejun@gmail.com: clean up comments and suggestions]
Cc: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sil used to trigger HSM error if IRQ occurs during polling
command. This didn't matter because polling wasn't used in sata_sil.
However, as of 2.6.20, all IDENTIFYs are performed by polling and
device detection sometimes fails due to spurious IRQ. This patch
makes sata_sil ignore and clear spurious IRQ while executing commands
by polling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
intx should be turned on when pci_enable_msi() fails not when it
succeeds. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
80c test mask is at bits 18 and 19 of EIDE Controller Configuration
not 22 and 23. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Duplicate ids noticed by Kay Sievers <kay.sievers@suse.de>
Although 100% different, this is based on a patch by Greg Kroah-Hartman
<gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recently Tejun wrote a patch to ahci.c to make it raise a HSM violation
if the drive attempted to complete a tag that wasn't outstanding. We could
run into the same problem with sata_nv ADMA. This adds code to raise a HSM
violation error if the controller gives us a notifier tag that isn't
outstanding, since the drive may be issuing spurious completions.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_nv implemented its own copies of the BMDMA helper functions for ADMA,
since the ADMA BMDMA status registers are PIO while the other registers
are MMIO, and this was the only way to handle this previously. Now that
we have iomap support, the standard routines should just work, so use them.
The only thing we need to override as far as ADMA and BMDMA is the
post_internal_cmd callback, where we should only call ata_post_internal_cmd
if we are in port-register mode.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Merge order left libata-acpi and pata_scc with remainling usage of
ap->id. Kill superflous id printing and substitute the remaining ones
with ap->print_id.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SDB FIS containing spurious NCQ completions is a clear protocol
violation. Currently, only some Maxtors with early firmware revisions
are showing this problem. Those firmwares have other NCQ related
problems including buggy NCQ error reporting and occasional lock up
after NCQ errors.
Consider spurious NCQ completions HSM violation and freeze the port
after it. EH will turn off NCQ after this happens several times.
Eventually drives which show this behavior should be blacklisted for
NCQ.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the DMA setup function. As pointed out by Sergey we set the actual
DMA clock timing in set_dmamode so we don't actually need to do anything
with it at set up time, but just leave the PIO timings loaded.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The CS5520 isn't just an ATA controller and we must not
pci_disable_device it as it turns into pci_disable_computer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can't specify which mode in the cases below but we can at least say
PIO and look consistent with the default.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port has two different id fields - id and port_no. id is
system-wide 1-based unique id for the port while port_no is 0-based
host-wide port number. The former is primarily used to identify the
ATA port to the user in printk messages while the latter is used in
various places in libata core and LLDs to index the port inside the
host.
The two fields feel quite similar and sometimes ap->id is used in
place of ap->port_no, which is very difficult to spot. This patch
renames ap->id to ap->print_id to reduce the possibility of such bugs.
Some printk messages are adjusted such that id string (ata%u[.%u])
isn't printed twice and/or to use ata_*_printk() instead of hardcoded
id format.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We already have code that handles hotplug interrupt indications in ADMA
mode, this turns on the control flag that actually enables these interrupts.
Also fixes some cases in the same functions where a 16-bit register was read
using a readl instead of a readw.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware provides us a notifier register that indicates what command
tags have completed. Use this to determine which CPBs to check, rather
than blindly checking all active CPBs. This should provide a minor
performance win, since if the controller has touched some of these
incomplete CPBs, accessing them will likely result in a cache miss.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This edits the taskfile setup to more closely match the way that libata
sends the taskfile for other controllers. This avoids putting taskfile writes
into the CPB buffer that are not needed according to the taskfile flags.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up the initialization of the CPB and APRD structures so that we
strictly follow the rules for ordering of writes to the CPB flags and
response flags, and prevent duplicate initialization.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When error handling occurs with pending commands, output the contents
of the next CPB count and next CPB index registers as well as the others,
since these may be useful for debugging.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata: Remove duplicate dma blacklist entry
The exact same entry is already present.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_pcmcia: Update device table
Add CFA devices from I-O Data, Mitsubishi and Viking. Add SanDisk comment.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conversion to resource-managed iomap was buggy causing init failures
on both vt6420 and 6421 - BAR5 wasn't mapped for both controllers
while on vt6420 sata_via tried to map BAR0-4 twice. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
