Fixed the following warnings:
WARNING: vmlinux.o(.text+0x2934): Section mismatch: reference to .init.text:__alloc_bootmem (between 'irq_alloc_host' and 'irq_set_default_host')
WARNING: vmlinux.o(.text+0xb2aa): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xb2b2): Section mismatch: reference to .init.data:boot_command_line (between 'register_early_udbg_console' and 'udbg_printf')
WARNING: vmlinux.o(.text+0xe354): Section mismatch: reference to .init.text:__alloc_bootmem (between 'pcibios_alloc_controller' and 'pci_domain_nr')
WARNING: vmlinux.o(.text+0x12768): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x127a8): Section mismatch: reference to .init.text:update_bridge_resource (between 'quirk_fsl_pcie_transparent' and 'indirect_read_config')
WARNING: vmlinux.o(.text+0x17566c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We didn't actually propogate the flag we pass into setup_indirect_pci()
to set indirect_type and thus were getting the wrong endianness if
PPC_INDIRECT_TYPE_BIG_ENDIAN was set.
Also, we need to or in additional flags rather than just doing a
direct assignment.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added the MPC85xx PCI device IDs that we need for the quirks we have.
Also, fixed the MPC8567E, MPC8567 device IDs which had the wrong value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add 8641/8641D device IDs as well.
All of which already exist or have been submitted to
The Linux PCI ID Repository at:
http://pci-ids.ucw.cz/
CC-to: pci-ids@ucw.cz
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some set of 85xx platforms have PCI-X controllers. The old arch/ppc
code setup these controllers and we haven't moved it over to arch/powerpc.
We use the PCI-X Capabilties to know if we are in PCI-X mode instead
of the Global Utilities PORDEVSR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the Freescale PCIe PHBs Not all firmwares setup the virtual P2P
bridge registers properly. Make sure they get setup based on what
the struct pci_controller got from the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the PCI capabilities to determine if we are PCIe PHB. Also use
PPC_INDIRECT_TYPE_NO_PCIE_LINK since the Freescale PCIe controllers
will lock the system if they don't have link and you try to do a config
access to anything but the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
