Uninitialised Apple iSight drivers present with a distinctive USB ID.
Once firmware has been uploaded, they disconnect and reconnect with a
new ID. At this point they can be driven by the uvcvideo driver. As this
is unique to the Apple cameras and not functionality shared by any other
UVC devices, it makes sense to provide the firmware loading
functionality in a separate driver. This driver will read an isight.fw
file extracted from the Apple driver using the tools at
http://bersace03.free.fr/ift/ and upload it to the camera. It will also
handle the case where the device loses its firmware during hibernation
and must have it reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.
A small number of units have been shipped early 2008
with a faulty USB Descriptor. Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/cpufreq/cpufreq.c the function cpufreq_add_dev() takes the
error exit 'err_out_unregister' from different places once with the
'cpu_policy_rwsem' lock held, once with the lock released:
| if (ret)
| goto err_out_unregister;
| }
|
| policy->governor = NULL; /* to assure that the starting sequence is
| * run in cpufreq_set_policy */
|
| /* set default policy */
| ret = __cpufreq_set_policy(policy, &new_policy);
| policy->user_policy.policy = policy->policy;
| policy->user_policy.governor = policy->governor;
|
| unlock_policy_rwsem_write(cpu);
|
| if (ret) {
| dprintk("setting policy failed\n");
| goto err_out_unregister;
| }
This leads to the following error message in case of a failing
__cpufreq_set_policy() call:
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
swapper/1 is trying to release lock (&per_cpu(cpu_policy_rwsem, cpu)) at:
[<c01b4564>] unlock_policy_rwsem_write+0x30/0x40
but there are no more locks to release!
other info that might help us debug this:
1 lock held by swapper/1:
#0: (sysdev_drivers_lock){--..}, at: [<c018fd18>] sysdev_driver_register+0x74/0x130
stack backtrace:
[<c002f588>] (dump_stack+0x0/0x14) from [<c00692fc>] (print_unlock_inbalance_bug+0xc8/0x104)
[<c0069234>] (print_unlock_inbalance_bug+0x0/0x104) from [<c006b7ac>] (lock_release_non_nested+0xc4/0x19c)
r6:00000028 r5:c3c1ab80 r4:c01b4564
[<c006b6e8>] (lock_release_non_nested+0x0/0x19c) from [<c006b9e0>] (lock_release+0x15c/0x18c)
r8:60000013 r7:00000001 r6:c01b4564 r5:c0541bb4 r4:c3c1ab80
[<c006b884>] (lock_release+0x0/0x18c) from [<c0061ba0>] (up_write+0x24/0x30)
r8:c0541b80 r7:00000000 r6:ffffffea r5:c3c34828 r4:c0541b8c
[<c0061b7c>] (up_write+0x0/0x30) from [<c01b4564>] (unlock_policy_rwsem_write+0x30/0x40)
r4:c3c34884
[<c01b4534>] (unlock_policy_rwsem_write+0x0/0x40) from [<c01b4c40>] (cpufreq_add_dev+0x324/0x398)
[<c01b491c>] (cpufreq_add_dev+0x0/0x398) from [<c018fd64>] (sysdev_driver_register+0xc0/0x130)
[<c018fca4>] (sysdev_driver_register+0x0/0x130) from [<c01b3574>] (cpufreq_register_driver+0xbc/0x174)
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dave Jones <davej@redhat.com>
improve the sysbench ramp-up phase and its peak throughput on
a 16way NUMA box, by turning on WAKE_AFFINE:
tip/sched tip/sched+wake-affine
-------------------------------------------------
1: 700 830 +15.65%
2: 1465 1391 -5.28%
4: 3017 3105 +2.81%
8: 5100 6021 +15.30%
16: 10725 10745 +0.19%
32: 10135 10150 +0.16%
64: 9338 9240 -1.06%
128: 8599 8252 -4.21%
256: 8475 8144 -4.07%
-------------------------------------------------
SUM: 57558 57882 +0.56%
this change also improves lat_ctx from 6.69 usecs to 1.11 usec:
$ ./lat_ctx -s 0 2
"size=0k ovr=1.19
2 1.11
$ ./lat_ctx -s 0 2
"size=0k ovr=1.22
2 6.69
in sysbench it's an overall win with some weakness at the lots-of-clients
side. That happens because we now under-balance this workload
a bit. To counter that effect, turn on NEWIDLE:
wake-idle wake-idle+newidle
-------------------------------------------------
1: 830 834 +0.43%
2: 1391 1401 +0.65%
4: 3105 3091 -0.43%
8: 6021 6046 +0.42%
16: 10745 10736 -0.08%
32: 10150 10206 +0.55%
64: 9240 9533 +3.08%
128: 8252 8355 +1.24%
256: 8144 8384 +2.87%
-------------------------------------------------
SUM: 57882 58591 +1.21%
as a bonus this not only improves the many-clients case but
also improves the (more important) rampup phase.
sysbench is a workload that quickly breaks down if the
scheduler over-balances, so since it showed an improvement
under NEWIDLE this change is definitely good.
Signed-off-by: Alexey Dobriyan <adobriyan@parallels.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent short-running wakers of short-running threads from overloading a single
cpu via wakeup affinity, and wire up disconnected debug option.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make sched_clock_cpu() return 0 before it has been initialized and avoid
corrupting its state due to doing so.
This fixes the weird printk timestamp jump reported.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Yanmin Zhang reported:
Comparing with 2.6.25, volanoMark has big regression with kernel 2.6.26-rc1.
It's about 50% on my 8-core stoakley, 16-core tigerton, and Itanium Montecito.
With bisect, I located the following patch:
| 18d95a2832 is first bad commit
| commit 18d95a2832
| Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
| Date: Sat Apr 19 19:45:00 2008 +0200
|
| sched: fair-group: SMP-nice for group scheduling
Revert it so that we get v2.6.25 behavior.
Bisected-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Coverity checker spotted a memleak introduced by commit
39106dcf85 (cpumask: use new cpus_scnprintf
function).
It seems the kfree() got lost between v2 and v3 of this patch...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
in net/bluetooth/rfcomm/sock.c, rfcomm_sk_state_change() does the
following operation:
if (parent && sock_flag(sk, SOCK_ZAPPED)) {
/* We have to drop DLC lock here, otherwise
* rfcomm_sock_destruct() will dead lock. */
rfcomm_dlc_unlock(d);
rfcomm_sock_kill(sk);
rfcomm_dlc_lock(d);
}
}
which is fine, since rfcomm_sock_kill() will call sk_free() which will call
rfcomm_sock_destruct() which takes the rfcomm_dlc_lock()... so far so good.
HOWEVER, this assumes that the rfcomm_sk_state_change() function always gets
called with the rfcomm_dlc_lock() taken. This is the case for all but one
case, and in that case where we don't have the lock, we do a double unlock
followed by an attempt to take the lock, which due to underflow isn't
going anywhere fast.
This patch fixes this by moving the stragling case inside the lock, like
the other usages of the same call are doing in this code.
This was found with the help of the www.kerneloops.org project, where this
deadlock was observed 51 times at this point in time:
http://www.kerneloops.org/search.php?search=rfcomm_sock_destruct
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addresses an alignment issue with compare_ether_addr().
The addresses passed to compare_ether_addr should be two bytes aligned.
It may function properly in x86 platform. However may not work properly
on IA-64 or ARM processor.
This also fixes a typo in mlme.c where the sk_buff struct name is incorect.
Though sizeof() works for any incorrect structure pointer name as its just
a pointer length that we want, lets just fix it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This addresses a NULL pointer dereference in sta_info_get().
TID and sta_info are extracted in ADDBA Timer expiry function
through the timer handler's argument.
The problem is extracging the TID (which was stored in
timer_to_tid[] array of type "u8") through "int *" typecast which
may also yield unwanted bytes for the MSB of TID that results
in incorrect sta_info and ieee80211_local pointers.
ieee80211_local pointer is NULL as illustrated below, it crashes in
sta_info_get(). The problem started when extracting ieee80211_local
pointer out of sta_info iteself and eventually crashed in
stat_info_get().
The proper way to fix is to change the data type of TID to u8
instead of u16. However changing all the occurences requires
some prototype changes as well. We should fix this in upcoming
patches.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix a typo in ieee80211_handle_filtered_frame comment
Signed-off-by: Yi Zhu <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Range check for power_output were missing.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a case that a wrong maximal rate is selected when
searching for better configurations.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When exiting from stay in table state (e.g. timer expiration),
all the statistics are reset and the RS flow should not continue
but only after enough statistics are collected again.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the rndis_wlan driver to connect to TKIP PSK
networks. It uses the ASSOCIATION_INFORMATION RNDIS call to pull back
the IEs and sends them back to userspace using wireless events. Tested
on a few wireless networks I have access to. Based on the similar
code in ndiswrapper.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
[edit: cleanups]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwconfig was showing incorrect status messages when disassociated.
Patch fixes this by always checking for association status in
ioctl calls for getting ap address.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_beacondone() is called from interrupt context,
this means we cannot use the mac80211 interface iterator
that uses the rtnl lock (since that uses a mutex which can sleep).
Instead we should use the atomic mac80211 interface iterator.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the antenna configuration has changed we should reset
the antenna RSSI value. Otherwise the value will be influenced
by the previous configuration quality which in turn will affect
the antenna diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link quality estimation became quite low for all rt2x00 drivers
because the number of retries it took to send the frame were
counted as failure.
This does not correspond to the legacy driver link quality calculation,
by not counting it we will send somewhat more optimistic values to
mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tx() handler runs while the device has disapeared,
we did return NETDEV_TX_OK but didn't free the skb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch switch order of channel and freq (SIOCGIWFREQ) reports
in scan results in order to overcome wpa_supplicant inability
to handle channel numbers in 5.2Ghz band.
Wext reporting channel number is ambiguous as channels 7-12 (802.11j)
exist on both bands.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes iee80211_rx_bss_put/get imbalance
introduced by 'mac80211: enable IBSS merging' patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates the beacon template code to upload both templates,
if we never uploaded one before.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The grf5101 RF code needs to invoke grf5101_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max2820 RF code needs to invoke max2820_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sa2400 RF code needs to invoke sa2400_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The static function max2820_rf_set_channel is called with conf == NULL
within its compilation unit. Originally this defaulted to b/g channel
1, but "cfg80211 API for channels/bitrates, mac80211 and driver
conversion" (commit 8318d78a44) mistakenly
dropped this check. This patch minimally restores the expected
behavior.
Reported-by: Colin Lai <colin_sh@163.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Set input bits for direct keys codes
2. Set input bits for rotary encoder codes only if rotary
encoder is enabled
3. Enable EV_REL only if rotary encoder is enabled and rel_codes
are set up
Signed-off-by: Antonio Ospite <ao2@openezx.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Whenever CONFIG_DEBUG_RODATA is set in the kernel config many kernel
text sections become read-only, and the use of software breakpoints in
the kgdb tests will cause the kernel to fail to complete the start up.
Until such time that there is an official API for modifying read-only
text sections hardware breakpoints must be used to run the do_fork or
sys_open tests or the tests get skipped.
Also fix the duplicated include reported by:
Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
> +#define ARCH_KMALLOC_MINALIGN (sizeof(long) * 2)
> +#define ARCH_SLAB_MINALIGN (sizeof(long) * 2)
This doesn't work if SLAB is selected and slab debugging is enabled as
these are passed to the preprocessor, and the preprocessor doesn't
understand sizeof.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: fix RCU problem in cfq_cic_lookup()
block: make blktrace use per-cpu buffers for message notes
Added in elevator switch message to blktrace stream
Added in MESSAGE notes for blktraces
block: reorder cfq_queue to save space on 64bit builds
block: Move the second call to get_request to the end of the loop
splice: handle try_to_release_page() failure
splice: fix sendfile() issue with relay
Specify the minimum slab/kmalloc alignment to be 8 bytes. This fixes a
crash when SLOB is selected as the memory allocator. The FRV arch needs
this so that it can use the load- and store-double instructions without
faulting. By default SLOB sets the minimum to be 4 bytes.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in the header guard of asm/ipc.h.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cfq_cic_lookup() needs to properly protect ioc->ioc_data before
dereferencing it and also exclude updaters of ioc->ioc_data as well.
Also add a number of comments documenting why the existing RCU usage
is OK.
Thanks a lot to "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> for
review and comments!
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Currently it uses a single static char array, but that risks
being corrupted when multiple users issue message notes at the
same time. Make the buffers dynamically allocated when the trace
is setup and make them per-cpu instead.
The default max message size of 1k is also very large, the
interface is mainly for small text notes. So shrink it to 128 bytes.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Allows messages to be inserted into blktrace streams.
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
