There is a typo in the ARM IXDP425 setup definition that mistakenly tries
to use UART1's IRQ for UART2's traffic.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch adds support for the LinkSys NSLU2 running with
both big and little-endian kernels. The LinkSys NSLU2 is
a cost engineered ARM, XScale 420 based system similar to
the the Intel IXDP425 evaluation board. It uses the
IXP4XX ARCH.
While this patch applies independently of other patches
the resultant kernel requires further patches to successfully
use onboard devices, including the onboard flash. Since these
patches are independent of this one they will be submitted
separately.
A defconfig is not included here because not all of
the required drivers are actually in the kernel.
We intend to provide one as soon as the patches
will be incorporated in mainstream.
This patch is the combined work of nslu2-linux.org
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch fixes AHB/PCI endianness problems when the
processor is in little-endian mode.
The patch configures the CSR register closely following the directives
in [1], paragraph 4.1, page 19.
According to the considerations in [1], page 11, while the AHB bus
supports both endian modes, on the IXP4XX it always uses big-endian.
The PCI bus is connected to the South AHB. A wrong setting in the CSR
register will thus cause a malfunctional PCI bus.
A schematic diagram of the bus interconnections on the IXP4XX
can be found in [1], page 18.
The patch has been verified to work on the NSLU2 in
both LE and BE modes.
The author is Peter Korsgaard.
[1] Intel® IXP4XX Product Line of Network Processors and IXC1100
Control Plane Processor:
Understanding Big Endian and Little Endian Modes
http://www.intel.com/design/network/applnots/25423701.pdf
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Deepak Saxena
IXP4xx map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Building a kernel for IXDP425 currently includes the machine descriptors
for IXDP465 and PRPMC1100 even if those machines are not configured.
This means we can build a kernel that boots on those machines even
though the machine_is_xxx() macro will always return 0 and other bits
such as PCI won't be compiled in. This can lead to many wasted hours
wondering what you have done to your kernel to make it randomly crash
thus requireing large quantities of beer to be consumed. While I am
all for consumption of large quantities of beer, there are better
reasons to do so then stupid kernel bugs.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch implements the set_irq_type() hooks for configuring GPIO
IRQ type and updates all the platforms to use it instead of the
gpio_line_config() function which is now used to configure input
vs. output on the pins.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
None of the board-specific map_io routines do anything, so kill them.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are currently reserving one byte more than actually needed by the flash
device and overlapping into the next I/O expansion bus window. This a)
causes us to allocate an extra page of VM due to ARM ioremap() alignment
code and b) could cause problems if another driver tries to request the
next expansion bus window.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Deepak Saxena
This allows the serial driver autconf to work properly on all the IXP
serial ports. W/o it we basically put the serial port in an unrecoverable
state and lose console.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch implements the iomap API for Intel IXP4xx NPU systems.
We need to implement our own version of the API functions b/c of the
PCI hostbridge does not provide the capability to map PCI I/O space
into the CPU's physical memory space. In addition, if a system has
more than 64M of PCI memory mapped BARs, PCI memory must also be
accessed indirectly. This patch changes the assignment of PCI I/O
resources to fall into to 0x0000:0xffff range so that we can trap
I/O areas in our ioread/iowrite macros.
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
coyote
Patch from Stefan Sorensen
On the ixdp425 and coyote platforms, the plat_serial8250_port arrays are
missing the terminating entry required by serial8250_probe.
Signed-off-by: Stefan Sorensen <ssoe@kirktelecom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VST needs to know which timer handler is for the timer interrupt.
Mark all timer interrupts with the SA_TIMER flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Current IXP4xx debug macros do not work in the small window between
the MMU being enabled and the call to map_io() b/c the standard
peripheral mapping is not properly setup for use with the low-level
debug code. This patch creates a new section-aligned mapping for the
UART specifically for use with the debug macros.
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
For some reason, this help text was missed when the file was last audited
by the documentation referencing folk. Fix this incorrect documentation
reference.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
