The purpose of an RPC ping (a NULL request) is to determine whether the
remote end is operating and supports the RPC program and version of the
request.
If we do an RPC bind and the remote's rpcbind service says "this
program or service isn't supported" then we have our answer already,
and we should give up immediately.
This is good for the kernel mount client, as it will cause the request
to fail, and then allow an immediate retry with different options.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add more new error code processing to the kernel's rpcbind client
and to call_bind_status() to distinguish two cases:
Case 1: the remote has replied that the program/version tuple is not
registered (returns EACCES)
Case 2: retry with a lesser rpcbind version (rpcb now returns EPFNOSUPPORT)
This change allows more specific error processing for each of these two
cases. We now fail case 2 instead of retrying... it's a server
configuration error not to support even rpcbind version 2. And don't
expose this new error code to user land -- convert it to EIO before
failing the RPC.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add new error code processing to the kernel's rpcbind client and to
call_bind_status() to distinguish two cases:
Case 1: the remote has replied that the program/version tuple is not
registered (returns -EACCES)
Case 2: another process is already in the middle of binding on this
transport (now returns -EAGAIN)
This change allows more specific retry processing for each of these two
cases.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When a server returns a bad rpcbind reply, make rpcbind client recovery logic
retry with an older protocol version. Older versions are more likely to work
correctly.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add better sanity checking of server replies to the GETVERSADDR reply
decoder. Change the error return code: EIO is what other XDR decoding
routines return if there is a failure while decoding.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
/home/cel/linux/net/sunrpc/clnt.c: In function ‘rpc_show_tasks’:
/home/cel/linux/net/sunrpc/clnt.c:1538: warning:
signed and unsigned type in conditional expression
This points out another case where a conditional expression returns a
signed value in one arm and an unsigned value in the other.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Check the length of the passed-in server name before trying to print it in
the log.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Noticed by Tom Talpey <tmt@netapp.com>:
OBTW, there's a nit on that memcpy, too. The r_addr is an array, so
memcpy(&map->r_addr
is passing the address of the array as a char **. It's the same as
map->r_addr, but technically the wrong type.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
/home/cel/linux/net/sunrpc/clnt.c: In function ‘rpc_bind_new_program’:
/home/cel/linux/net/sunrpc/clnt.c:445: warning:
comparison between signed and unsigned
RPC version numbers are u32, not int.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Remove one of two identical dprintk's that occur when an RPC client is
created.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fix some problems with rpcbind v3 and v4 queries from the in-kernel rpcbind
client:
1. The r_addr argument must be a full universal address, not just an IP
address, and
2. The universal address in r_addr is the address of the remote rpcbind
server, not the RPC service being requested
This addresses bugzilla.kernel.org report 8891 for 2.6.23-rc and greater.
In addition, if the rpcbind client is unable to start the rpcbind request,
make sure not to leak the xprt.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
"Universal addresses" are a string representation of an IP address and
port. They are described fully in RFC 3530, section 2.2. Add support
for generating them in the RPC client's socket transport module.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Finalize support for setting up RPC client transports to remote RPC
services addressed via IPv6.
Based on work done by Gilles Quillard at Bull Open Source.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare for introduction of IPv6 versions of same.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Finishing a socket connect is the same for IPv4 and IPv6, so split it out
into a helper.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clone xs_bindresvport into two functions, one that can handle IPv4
addresses, and one that can handle IPv6 addresses.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We could clone xs_set_port, but this is easier overall.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare for adding IPv6 support to the RPC client by adding IPv6
capabilities to rpcbind. Note that this is support on the query side
only; registering IPv6 addresses with the local portmapper will come
later.
Note we have to take care not to fall back to using version 2 of the
rpcbind protocol if we're dealing with IPv6 address. Version 2 doesn't
support IPv6 at all.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare to add an IPv6 version of xs_format_peer_addresses by renaming it
to xs_format_ipv4_peer_addresses.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add support for the NFS client's need to export volume information
with IP addresses formatted in hex instead of decimal.
This isn't used yet, but subsequent patches (not in this series) will
change the NFS client to use this functionality.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Use more generic logic to free buffers holding formatted addresses. This
makes it less likely a bug will be introduced when adding additional buffer
types in xs_format_peer_address().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
include/linux/kernel.h gives us some nice macros for formatting IP
addresses. Use them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This will allow rpc.gssd to use inotify instead of dnotify in order to
locate new rpc upcall pipes.
This also requires the exporting of __audit_inode_child(), which is used by
fsnotify_create() and fsnotify_mkdir(). Ccing David Woodhouse.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When the ICMPv6 Target address is multicast, Linux processes the
redirect instead of dropping it. The problem is in this code in
ndisc_redirect_rcv():
if (ipv6_addr_equal(dest, target)) {
on_link = 1;
} else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) {
ND_PRINTK2(KERN_WARNING
"ICMPv6 Redirect: target address is not
link-local.\n");
return;
}
This second check will succeed if the Target address is, for example,
FF02::1 because it has link-local scope. Instead, it should be checking
if it's a unicast link-local address, as stated in RFC 2461/4861 Section
8.1:
- The ICMP Target Address is either a link-local address (when
redirected to a router) or the same as the ICMP Destination
Address (when redirected to the on-link destination).
I know this doesn't explicitly say unicast link-local address, but it's
implied.
This bug is preventing Linux kernels from achieving IPv6 Logo Phase II
certification because of a recent error that was found in the TAHI test
suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the
multicast address in the Destination field instead of Target field, so
we were passing the test. This won't be the case anymore.
The patch below fixes this problem, and also fixes ndisc_send_redirect()
to not send an invalid redirect with a multicast address in the Target
field. I re-ran the TAHI Neighbor Discovery section to make sure Linux
passes all 245 tests now.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When only GSO skb was partially ACKed, no hints are reset,
therefore fastpath_cnt_hint must be tweaked too or else it can
corrupt fackets_out. The corruption to occur, one must have
non-trivial ACK/SACK sequence, so this bug is not very often
that harmful. There's a fackets_out state reset in TCP because
fackets_out is known to be inaccurate and that fixes the issue
eventually anyway.
In case there was also at least one skb that got fully ACKed,
the fastpath_skb_hint is set to NULL which causes a recount for
fastpath_cnt_hint (the old value won't be accessed anymore),
thus it can safely be decremented without additional checking.
Reported by Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC net/ieee80211/softmac/ieee80211softmac_wx.o
/home/kernel/src/net/ieee80211/softmac/ieee80211softmac_wx.c: In function âieee80211softmac_wx_set_essidâ:
/home/kernel/src/net/ieee80211/softmac/ieee80211softmac_wx.c:117: warning: label âoutâ defined but not used
due to commit: efe870f9f4. Removing the label.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Chris Evans <scarybeasts@gmail.com>:
> The summary is that an evil 80211 frame can crash out a victim's
> machine. It only applies to drivers using the 80211 wireless code, and
> only then to certain drivers (and even then depends on a card's
> firmware not dropping a dubious packet). I must confess I'm not
> keeping track of Linux wireless support, and the different protocol
> stacks etc.
>
> Details are as follows:
>
> ieee80211_rx() does not explicitly check that "skb->len >= hdrlen".
> There are other skb->len checks, but not enough to prevent a subtle
> off-by-two error if the frame has the IEEE80211_STYPE_QOS_DATA flag
> set.
>
> This leads to integer underflow and crash here:
>
> if (frag != 0)
> flen -= hdrlen;
>
> (flen is subsequently used as a memcpy length parameter).
How about this?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is followup to Patrick's patch. A little optimization to enqueue
routine allows to remove artificial limitation on queue length.
Plus, testing showed that hash function used by SFQ is too bad or even worse.
It does not even sweep the whole range of hash values.
Switched to Jenkins' hash.
Signed-off-by: Alexey Kuznetsov <kaber@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a report and initial patch by Peter Lieven.
tcp4_md5sig_key and tcp6_md5sig_key need to start with
the exact same members as tcp_md5sig_key. Because they
are both cast to that type by tcp_v{4,6}_md5_do_lookup().
Unfortunately tcp{4,6}_md5sig_key use a u16 for the key
length instead of a u8, which is what tcp_md5sig_key
uses. This just so happens to work by accident on
little-endian, but on big-endian it doesn't.
Instead of casting, just place tcp_md5sig_key as the first member of
the address-family specific structures, adjust the access sites, and
kill off the ugly casts.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes kernel bugzilla #5731
It should generate an empty packet for datagram protocols when the
socket is connected, for one.
The check is doubly-wrong because all that a write() can be is a
sendmsg() call with a NULL msg_control and a single entry iovec. No
special semantics should be assigned to it, therefore the zero length
check should be removed entirely.
This matches the behavior of BSD and several other systems.
Alan Cox notes that SuSv3 says the behavior of a zero length write on
non-files is "unspecified", but that's kind of useless since BSD has
defined this behavior for a quarter century and BSD is essentially
what application folks code to.
Based upon a patch from Stephen Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
It gets pointer to fastcall function, expects a pointer to normal
one and calls the sucker.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ADDIP is enabled, when an ASCONF chunk is received with ASCONF
paramter length set to zero, this will cause infinite loop.
By the way, if an malformed ASCONF chunk is received, will cause
processing to access memory without verifying.
This is because of not check the validity of parameters in ASCONF chunk.
This patch fixed this.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
RFC 4460 and future RFC 4960 (2960-bis) specify that packets
with bundled INIT chunks need to be dropped. We currenlty do
that only after processing any leading chunks. For OOTB chunks,
since we already walk the entire packet, we should discard packets
with bundled INITs.
There are other chunks chunks that MUST NOT be bundled, but the spec
is silent on theire treatment. Thus, we'll leave their teatment
alone for the moment.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com>
While processing OOTB chunks as well as chunks with an invalid
length of 0, it was possible to SCTP to get wedged inside an
infinite loop because we didn't catch the condition correctly,
or didn't mark the packet for discard correctly.
This work is based on original findings and work by
Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Explicitely discard OOTB chunks, whether the result is a
SHUTDOWN COMPLETE or an ABORT. We need to discard the OOTB
SHUTDOWN ACK to prevent bombing attackes since responsed
MUST NOT be bundled. We also explicietely discard in the
ABORT case since that function is widely used internally.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
When SCTP client received an INIT ACK chunk with missing mandatory
parameter such as "cookie parameter", it will send back a ABORT
with T-bit not set and verification tag is set to 0.
This is because before we accept this INIT ACK chunk, we do not know
the peer's tag. This patch change to reflect vtag when responding to
INIT ACK with missing mandatory parameter.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When we process bundled chunks, we need to make sure that
the skb has the buffer for each header since we assume it's
always there. Some malicious node can send us something like
DATA + 2 bytes and we'll try to walk off the end refrencing
potentially uninitialized memory.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
When mac80211 is built into the kernel it needs to init earlier
so that device registrations are run after it has initialised.
The same applies to rate control algorithms.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wme.c triggers a sparse warning; it wasn't noticed before because until
recently ARRAY_SIZE triggered a sparse error.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
