1
Commit Graph

10701 Commits

Author SHA1 Message Date
Ivo van Doorn
8058409c4f rt2x00: Block set_key() during suspend/shutdown
mac80211 will call set_key() when the device is
shutting down. When the device is unplugged the
keys will be lost automatically due to the power
loss. When the device is not plugged but the module
is only unloaded the keys can remain in the device
hardware, when the module is loaded the keys will
be cleaned up during initialization.

This should prevent the problem reported by Johannes Berg,
where unplugging the device while suspended resulted in
a NULL pointer error during set_key() which was
caused because of the CSR base address being freed.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:05 -05:00
Ivo van Doorn
9a95dba327 rt2x00: Fix LED state handling
For every global LED state change (register/unregister,
suspend/resume) we should force the LEDS to turn off.
This makes sure that the LEDS will always be in a sane
state after the state switch.

Note that when unregister is called but the LED class
wasn't resumed yet, we shouldn't change the LED state
since we might not have access to the device (device
was unplugged while suspended).

Also remove the checks in the activity, assoc and
radio LEDS which blocked calls to brightness_set()
when the state hasn't changed. Some of those LEDS
could be enabled by themselves when something happens
in the hardware (e.g. firmware is loaded). We already
did called rt2x00leds to switch the LED off, but those
calls were blocked.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:05 -05:00
Ivo van Doorn
3d8606a680 rt2x00: Remove RATE_BASIC flag
mac80211 is in charge of determining the basic rates,
so we are not using the RATE_BASIC flag anymore.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:05 -05:00
Larry Finger
1c740ed221 Move all rtl818x files to a common directory.
This change improves the maintainability of these drivers. No functionality
is changed.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:04 -05:00
Andrey Yurovsky
55b3961953 mac80211_hwsim: enable Mesh Point operation
Initial mesh support: add Mesh Point to supported interfaces mask and allow
hwsim to send beacons in mesh mode.

Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:04 -05:00
Anna Neal
582c1b538f libertas: Fine grained configuration of wake-on-lan.
Based on a patch from Shailendra Govardhan <shailen@marvell.com>.
This patch allows implementation of more specific wake-on-lan rules than those
of ethtool.

Please note that only firmware 5.110.22.p20 and above supports this feature.

This patch only implements the driver/firmware interface, not the
userspace/driver interface.

Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:03 -05:00
John W. Linville
50da3ead62 ipw2100, ipw2200: select LIB80211
Otherwise some configs can result in missing print_ssid...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:03 -05:00
John W. Linville
3d29b0c33d netdevice zd1201: Convert directly reference of netdev->priv to netdev_priv()
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
and I want to kill netdev->priv later, I decided to convert all the direct
reference of netdev->priv first.

(Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
changelog but using dev->ml_priv.  That doesn't seem appropriate
to me for this driver, so I've revamped it to use netdev_priv()
instead. -- JWL)

Reviewed-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-21 11:06:02 -05:00
Wang Chen
9d2f472097 ixgbe: convert directly reference of netdev->priv
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-21 01:56:07 -08:00
Donald Skidmore
c4900be053 ixgbe: add SFP+ driver support
This patch adds support for SFP+ PHY in the following device ID's (10DB,
10F1, 10E1).  These SFP+ PHY's are accessed via an I2C interface so the
patch also includes functions to support this.

Another feature of note is that the PHY is pluggable and some
rearchitecting was needed to support this.

Signed-off-by: Donald Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:11:42 -08:00
Alexander Duyck
859ee3c438 DCB: Add support for DCB BCN
Adds an interface to configure the Backward Congestion Notification
(BCN) feature.  In a BCN capabale network, congestion notifications
from congested points out in the network can cause the end station
limit the rate of a given traffic flow.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:10:23 -08:00
Alexander Duyck
0eb3aa9bab DCB: Add interface to query the state of PFC feature.
Adds a netlink interface for Data Center Bridging (DCB) to get and set
the enable state of the Priority Flow Control (PFC) feature.
Primarily, this is a way to turn off PFC in the driver while DCB
remains enabled.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:09:23 -08:00
Alexander Duyck
33dbabc4a7 DCB: Add interface to query # of TCs supported by device
Adds interface for Data Center Bridging (DCB) to query (and set if
supported) the number of traffic classes currently supported by the
device for the two (DCB) features: priority groups (PG) and priority
flow control (PFC).

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:08:19 -08:00
Alexander Duyck
46132188bf DCB: Add interface to query for the DCB capabilities of an device.
Adds to the netlink interface for Data Center Bridging (DCB), allowing
the DCB capabilities supported by a device to be queried.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 21:05:08 -08:00
Alexander Duyck
2f90b8657e ixgbe: this patch adds support for DCB to the kernel and ixgbe driver
This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel.  The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:52:10 -08:00
Stephen Hemminger
748ff68fad hippi: convert driver to net_device_ops
Convert the HIPPI infrastructure for use with net_device_ops.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:32:15 -08:00
Stephen Hemminger
fd8f4997e3 defxx: convert driver to net_device_ops
Convert this driver to net_device_ops.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:31:40 -08:00
Stephen Hemminger
145186a395 fddi: convert to new network device ops
Similar to ethernet. Convert infrastructure and the one lone FDDI
driver (for the one lone user of that hardware??). Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:29:48 -08:00
Stephen Hemminger
aa18e9e88c dummy: convert to net_device_ops
Convert to new network device ops interface.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:28:00 -08:00
Stephen Hemminger
008298231a netdev: add more functions to netdevice ops
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.

Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 20:14:53 -08:00
David S. Miller
6ab33d5171 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/net/ixgbe/ixgbe_main.c
	include/net/mac80211.h
	net/phonet/af_phonet.c
2008-11-20 16:44:00 -08:00
Wang Chen
7be6065b39 netdevice wanrouter: Convert directly reference of netdev->priv
1. Make device driver to allocate memory for netdev.
2. Convert all directly reference of netdev->priv to netdev_priv().

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 04:26:21 -08:00
Wang Chen
826dd0e1e3 netdevice ni65: Convert directly reference of netdev->priv
This patch is to kill directly reference of netdev->priv too.
Because the private data needs special memory: lower 16MB DMA.
alloc_etherdev() can not do this work.
So we can't use netdev->priv to point to netdev's private data.
Use netdev->ml_priv instead.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 04:25:06 -08:00
Wang Chen
c8019bf3af netdevice ppp: Convert directly reference of netdev->priv
1. Use netdev_priv(dev) to replace dev->priv.
2. Alloc netdev's private data by alloc_netdev().

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 04:24:17 -08:00
Steve Glendinning
f7b29271c3 smsc95xx: add tx checksum offload support
LAN9500 supports tx checksum offload, which slightly decreases cpu
utilisation.  The benefit isn't very large because we still require
the skb to be linearized, but it does save a few cycles.

This patch adds support for it, and enables it by default.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 04:19:21 -08:00
Alan Jenkins
a849854fc7 atl2: don't request irq on resume if netif running
If the device is suspended with the cable disconnected, then
resumed with the cable connected, dev->open is called before
resume. During resume, we request an IRQ, but the IRQ was
already assigned during dev->open, resulting in the warning
shown below.

Don't request an IRQ if the device is running.

Call Trace:
 [<c011b89a>] warn_on_slowpath+0x40/0x59
 [<c023df15>] raw_pci_read+0x4d/0x55
 [<c023dff3>] pci_read+0x1c/0x21
 [<c01bcd81>] __pci_find_next_cap_ttl+0x44/0x70
 [<c01bce86>] __pci_find_next_cap+0x1a/0x1f
 [<c01bcef9>] pci_find_capability+0x28/0x2c
 [<c01c4144>] pci_msi_check_device+0x53/0x62
 [<c01c49c2>] pci_enable_msi+0x3a/0x1cd
 [<e019f17b>] atl2_write_phy_reg+0x40/0x5f [atl2]
 [<c01061b1>] dma_generic_alloc_coherent+0x0/0xd7
 [<e019f107>] atl2_request_irq+0x15/0x49 [atl2]
 [<e01a1481>] atl2_open+0x20b/0x297 [atl2]
 [<c024a35c>] dev_open+0x62/0x91
 [<c0248b9a>] dev_change_flags+0x93/0x141
 [<c024f308>] do_setlink+0x238/0x2d5
 [<c02501b2>] rtnl_setlink+0xa9/0xbf
 [<c0297f0c>] mutex_lock+0xb/0x19
 [<c024ffa7>] rtnl_dump_ifinfo+0x0/0x69
 [<c0250109>] rtnl_setlink+0x0/0xbf
 [<c024fe42>] rtnetlink_rcv_msg+0x185/0x19f
 [<c0240fd1>] sock_rmalloc+0x23/0x57
 [<c024fcbd>] rtnetlink_rcv_msg+0x0/0x19f
 [<c0259457>] netlink_rcv_skb+0x2d/0x71
 [<c024fcb7>] rtnetlink_rcv+0x14/0x1a
 [<c025929e>] netlink_unicast+0x184/0x1e4
 [<c025992a>] netlink_sendmsg+0x233/0x240
 [<c023f405>] sock_sendmsg+0xb7/0xd0
 [<c0129131>] autoremove_wake_function+0x0/0x2b
 [<c0129131>] autoremove_wake_function+0x0/0x2b
 [<c0147796>] mempool_alloc+0x2d/0x9e
 [<c020c923>] scsi_pool_alloc_command+0x35/0x4f
 [<c0297f0c>] mutex_lock+0xb/0x19
 [<c028e867>] unix_stream_recvmsg+0x357/0x3e2
 [<c01b81c9>] copy_from_user+0x23/0x4f
 [<c02452ea>] verify_iovec+0x3e/0x6c
 [<c023f5ab>] sys_sendmsg+0x18d/0x1f0
 [<c023ffa8>] sys_recvmsg+0x146/0x1c8
 [<c0240016>] sys_recvmsg+0x1b4/0x1c8
 [<c0118f48>] __wake_up+0xf/0x15
 [<c02586cd>] netlink_table_ungrab+0x17/0x19
 [<c01b83ba>] copy_to_user+0x25/0x3b
 [<c023fe4a>] move_addr_to_user+0x50/0x68
 [<c0240266>] sys_getsockname+0x6f/0x9a
 [<c0240280>] sys_getsockname+0x89/0x9a
 [<c015046a>] do_wp_page+0x3ae/0x41a
 [<c0151525>] handle_mm_fault+0x4c5/0x540
 [<c02405d0>] sys_socketcall+0x176/0x1b0
 [<c010376d>] sysenter_do_call+0x12/0x21

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 04:18:25 -08:00
Ben Hutchings
8761169cf1 sfc: Fix dependency for SFC_MTD
Randy Dunlap found that SFC_MTD was selected when sfc was built-in and
the MTD core was a module.  Don't allow that combination.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 04:17:42 -08:00
Wang Chen
c0103606b7 netdevice lance: Convert directly reference of netdev->priv
This patch is to kill directly reference of netdev->priv too.
Because the private data should be allocated in DMA area, alloc_etherdev()
can't satisfy this needs.
Use netdev->ml_priv to point to lance_private.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 04:05:56 -08:00
David S. Miller
f7f65d1e8b Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2008-11-20 04:01:29 -08:00
Lennert Buytenhek
5377152264 mv643xx_eth: calculate descriptor pointer only once in rxq_refill()
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 03:59:04 -08:00
Lennert Buytenhek
f61e554776 mv643xx_eth: move receive error handling out of line
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 03:58:46 -08:00
Lennert Buytenhek
66e63ffbc0 mv643xx_eth: implement ->set_rx_mode()
Currently, if multiple unicast addresses are programmed into a
mv643xx_eth interface, the core networking will resort to enabling
promiscuous mode on the interface, as mv643xx_eth does not implement
->set_rx_mode().

This patch switches mv643xx_eth over from ->set_multicast_list()
to ->set_rx_mode(), and implements support for secondary unicast
addresses.  The hardware can handle multiple unicast addresses as
long as their first 11 nibbles are the same (i.e. are of the form
xx:xx:xx:xx:xx:xy where the x part is the same for all addresses), so
if that is the case, we use that mode.  If it's not the case, we enable
unicast promiscuous mode in the hardware, which is slightly better than
enabling promiscuous mode for multicasts as well, which is what would
happen before.

While we are at it, change the programming sequence so that we
don't clear all filter bits first, so we don't lose all incoming
packets while the filter is being reprogrammed.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 03:58:27 -08:00
Lennert Buytenhek
66823b928d mv643xx_eth: inline txq_alloc_desc_index()
Since txq_alloc_desc_index() is a very simple function, and since
descriptor ring index handling for transmit reclaim, receive
processing and receive refill is already handled inline as well,
inline txq_alloc_desc_index() into its two call sites.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 03:58:09 -08:00
Lennert Buytenhek
37a6084f4b mv643xx_eth: introduce per-port register area pointer
The mv643xx_eth driver uses the rdl()/wrl() macros to read and
write hardware registers.  Per-port registers are accessed in the
following way:

	#define PORT_STATUS(p)			(0x0444 + ((p) << 10))

	[...]

	static inline u32 rdl(struct mv643xx_eth_private *mp, int offset)
	{
		return readl(mp->shared->base + offset);
	}

	[...]

	port_status = rdl(mp, PORT_STATUS(mp->port_num));

By giving the per-port 'struct mv643xx_eth_private' its own
'void __iomem *base' pointer that points to the per-port register
area, we can get rid of both the double indirection and the << 10
that is done for every per-port register access -- this patch does
that.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 03:57:36 -08:00
Lennert Buytenhek
10a9948d13 mv643xx_eth: checkpatch fixes
Fix up a couple of coding style issues caught by checkpatch.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 03:57:16 -08:00
Vernon Sauder
eafdcb433f smc911x: Fix printf format typo in smc911x driver.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:56:08 -08:00
Brice Goglin
00b5e50549 myri10ge: remove hardcoded sram_size
Removes the use of a hardcoded sram_size, determine string_spec
location from the MCP header instead.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:50:28 -08:00
Brice Goglin
d6279c88f2 myri10ge: fix per-slice rx/tx_dropped counters
Properly attribute transmit and receive drops by incrementing the
per-slice counter.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:50:04 -08:00
Pantelis Koukousoulas
a7f75c0c9c asix: Fix asix-based cards connecting to 10/100Mbs LAN.
Add AX_MEDIUM_ENCK also when speed = 10/100Mbps. This allows my belkin
f5d5055 to work with my 100Mbps switch and with an old 10Mbps ISA card.
Without this patch, the card is recognized and the interface is brought
up fine, but no packets actually flow through the interface.

Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:48:46 -08:00
Lennert Buytenhek
11b4aa03b2 mv643xx_eth: fix recycle check bound
When mv643xx_eth allocates skbuffs, it adds
'dma_get_cache_alignment() - 1' to the length it needs, so that it can
align the skb's ->data pointer to a cache boundary.  When checking
whether a transmitted skbuff can be reused as a receive buffer, these
bytes needs to be included into the minimum bound for the recycle check.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:39:52 -08:00
Lennert Buytenhek
bcb3336ce4 mv643xx_eth: fix the order of mdiobus_{unregister, free}() calls
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:39:40 -08:00
Mike Frysinger
a61fc1e995 netdev/smc91x: unify Blackfin code a bit and use proper read/write functions
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:32:34 -08:00
Nobuhiro Iwamatsu
fb5e2f9b94 sh: sh_eth: Update to change of mii_bus
Update to change of mii_bus interface and fix some warning.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:28:30 -08:00
Wang Chen
f4bdd264b4 netdevice hamradio: Convert directly reference of netdev->priv
Since all the memory, which pointed by netdev->priv, are allocated in
advance instead of by alloc_netdev().  Use netdev->ml_priv to point to
those memory.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:02:05 -08:00
Wang Chen
f3a216d1da netdevice: 82596: Convert netdev->priv to netdev_priv
1. When alloc_etherdev(), no memory be allocated to netdev->priv.
2. And it's need to get a whole page for priv.

For these reasons, use netdev->ml_priv to point to the page is the
best method to convert directly reference of netdev->priv.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 01:01:00 -08:00
Alexander Duyck
68fd991020 igb: Fix tx/rx_ring_count parameters for igb on suspend/resume/ring resize
When suspending the device the ring structure is freed which causes it to
loose track of the count.  To resolve this we need to move the ring count
outside of the ring structure and store it in the adapter struct.

In addition to resolving the suspend/resume issue this patch also addresses
issues seen in the event of memory allocation errors causing uneven ring
sizes on multiple queues.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 00:48:10 -08:00
Alexander Duyck
b2d565365e igb: simplify swap in clean_rx_irq if using packet split
This update replaces the xchg calls that were added with a pair of
assignments as there is no need for the xchg calls and they were found to
cause issues on some architectures.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 00:47:34 -08:00
Alexander Duyck
3ef6b2354f igb: update name to reflect new hardware
This patch adds the 82576 device to the description for igb in Kconfig.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20 00:46:57 -08:00
Stephen Hemminger
d8b83c57a7 acenic: convert to net_device_ops
Convert this driver to network device ops. Compile tested only.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-19 22:42:59 -08:00
Stephen Hemminger
2c9171d4ef niu: convert to net_device_ops
Convert this driver to network device ops. Compile tested only (give me hw!)

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-19 22:42:58 -08:00