Commit 6aa85a5ae6 (omap4: 4430sdp:
enable the ehci port on 4430SDP) added code to enable EHCI
support on 4430sdp board.
Looks like the ULPI pin does not seem to be muxed properly on ES1.0
SDP and this causes the system to reboot when the ULPI PHY is
enabled.
Fix this by muxing the pin, this is the same setting for
both ES1.0 and ES2.0. Also add checking for gpio_request.
Cc: Keshava Munegowda <keshava_mgowda@ti.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
TFP410 DVI chip is used to provide display out.
This chip is controlled by 2 lines:
LDO which supplies the power is controlled over gpio + 2
and the enable of the chip itself is done over gpio + 1
NOTE: the LDO is necessary for LED, serial blocks as well.
gpio + 1 was used to sense USB overcurrent in vanilla beagle.
Without this fix, the display would not function as the LDO
remains shut down.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_reserve functionality to board-igep0030.c.
This patch is in similar lines to commit id 71ee7dad9b, from
Russell king
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO reset line for Beagle XM is different from vanilla beagle
so we populate it as part of gpio update routine.
This in part fixes the issue of display not functioning on beagle XM
platform.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI enable power pin is inverted (active high) in comparison
to vanilla beagle which is active low. Handle this case conditionally.
Without this fix, Beagle XM 4 port EHCI will not function and no
networking will be available
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support twl4030 keypad and gpio keys on IGEP v2.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second MMC channel (used by the WLAN/BT module) is not linked to
power regulator. This causes the WLAN/BT module to fail being detected if
CONFIG_REGULATOR_DUMMY is not set.
This patch adds the two regulators that actually feed the WLAN/BT module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module has one EHCI interface on board using
USB2HS port. GPIO183 is used as PHY reset.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At latest mainline commit 0c21e3aaf6, omap2plus build is broken. This
patch is trivial fix for the missed usb clock node for CK_3430ES2PLUS
flag update.
CHK include/generated/compile.h
CC arch/arm/mach-omap2/clock3xxx_data.o
arch/arm/mach-omap2/clock3xxx_data.c:3289: error: 'CK_3430ES2' undeclared
here (not in a function)
make[1]: *** [arch/arm/mach-omap2/clock3xxx_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated mask to include CK_36XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SMSC 3320 USB PHY on the OMAP4 Pandaboard needs a 19.2 MHz
reference clock. This clock is provided from the OMAP4's fref_clk3
pad.
Recent changes to clock44xx_data.c made the clock framework aware
of the existence of these fref_clk[i] lines. If the option
CONFIG_OMAP_RESET_CLOCKS is enabled in the kernel, then the
clock framework will turn these clocks off during bootup.
Explicitly request and keep this clock enabled at init for the
Pandaboard, so that the PHY receives this clock at all times.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap2plus_defocnfig build breaks when customised with only ARCH_OMAP4
selected. This is because common files make references to the functions
which are defined only for omap2xxx and omap3xxx.
LD .tmp_vmlinux1
arch/arm/mach-omap2/built-in.o: In function `pm_dbg_regset_store':
arch/arm/mach-omap2/pm-debug.c:335: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap2_pm_dump':
arch/arm/mach-omap2/pm-debug.c:121: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:123: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:124: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/pm-debug.c:125: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap_prcm_arch_reset':
arch/arm/mach-omap2/prcm.c:106: undefined reference to `omap2_prm_set_mod_reg_bits'
arch/arm/mach-omap2/prcm.c:108: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `omap_prcm_get_reset_sources':
arch/arm/mach-omap2/prcm.c:53: undefined reference to `omap2_prm_read_mod_reg'
arch/arm/mach-omap2/built-in.o: In function `clkdm_clear_all_wkdeps':
arch/arm/mach-omap2/clockdomain.c:545: undefined reference to `omap2_prm_clear_mod_reg_bits'
arch/arm/mach-omap2/built-in.o: In function `clkdm_del_wkdep':
arch/arm/mach-omap2/clockdomain.c:475: undefined reference to `omap2_prm_clear_mod_reg_bits'
arch/arm/mach-omap2/built-in.o: In function `clkdm_read_wkdep':
arch/arm/mach-omap2/clockdomain.c:511: undefined reference to `omap2_prm_read_mod_bits_shift'
arch/arm/mach-omap2/built-in.o: In function `clkdm_add_wkdep':
arch/arm/mach-omap2/clockdomain.c:440: undefined reference to `omap2_prm_set_mod_reg_bits'
make: *** [.tmp_vmlinux1] Error 1
This patch adds stubs for these functions so that build continues to work.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
CC arch/arm/mach-omap2/omap_hwmod_common_data.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod_common_data.c:20:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_late_init':
arch/arm/plat-omap/include/plat/voltage.h:145: error: 'EINVAL' undeclared (first use in this function)
arch/arm/plat-omap/include/plat/voltage.h:145: error: (Each undeclared identifier is reported only once
arch/arm/plat-omap/include/plat/voltage.h:145: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-omap2/omap_hwmod_common_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
LD init/built-in.o
LD .tmp_vmlinux1
arch/arm/mach-omap2/built-in.o: In function `omap2_set_init_voltage':
arch/arm/mach-omap2/pm.c:181: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/built-in.o: In function `omap4_twl_init':
arch/arm/mach-omap2/omap_twl.c:244: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/omap_twl.c:247: undefined reference to `omap_voltage_domain_lookup'
arch/arm/mach-omap2/omap_twl.c:250: undefined reference to `omap_voltage_domain_lookup'
make: *** [.tmp_vmlinux1] Error 1
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix below build warnings
CC arch/arm/mach-omap2/common.o
CC arch/arm/mach-omap2/gpio.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/gpio.c:25:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/dma.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/dma.c:32:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/wd_timer.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/wd_timer.c:15:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/prm44xx.o
CC arch/arm/mach-omap2/omap_hwmod.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod.c:145:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
CC arch/arm/mach-omap2/omap_hwmod_common_data.o
In file included from arch/arm/plat-omap/include/plat/omap_hwmod.h:38,
from arch/arm/mach-omap2/omap_hwmod_common_data.c:20:
arch/arm/plat-omap/include/plat/voltage.h: In function 'omap_voltage_register_pmic':
arch/arm/plat-omap/include/plat/voltage.h:137: warning: no return statement in function returning non-void
The error is reported when omap2plus_defconfig built with CONFIG_PM disabled
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
struct clockdomain member clktrctrl_mask is available for only for OMAP2
and OMAP3 architectures. Technially it is also used only for these archs
but this breaks the build with custom OMAP4 configuration.
CC arch/arm/mach-omap2/clockdomain.o
arch/arm/mach-omap2/clockdomain.c: In function '_enable_hwsup':
arch/arm/mach-omap2/clockdomain.c:251: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:254: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function '_disable_hwsup':
arch/arm/mach-omap2/clockdomain.c:277: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:280: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_sleep':
arch/arm/mach-omap2/clockdomain.c:744: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_wakeup':
arch/arm/mach-omap2/clockdomain.c:789: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_clk_enable':
arch/arm/mach-omap2/clockdomain.c:922: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:926: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c: In function 'omap2_clkdm_clk_disable':
arch/arm/mach-omap2/clockdomain.c:994: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
arch/arm/mach-omap2/clockdomain.c:998: error: 'struct clockdomain' has no member named 'clktrctrl_mask'
make[1]: *** [arch/arm/mach-omap2/clockdomain.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Fix the build break by dropping the #ifdef as suggested by Paul Walmsley
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Instead of accessing the irq_desc array directly
we can use irq_to_desc(irq). That will allow us to,
if wanted, select SPARSE_IRQ and irq_descs will be
added to a radix tree, instead of a array.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap_pm_runtime_suspend and omap_pm_runtime_resume are used
as function pointers and does not really need to be exposed
to the world.
Fixes sparse warnings:
arch/arm/mach-omap2/pm_bus.c:23:5: warning: symbol 'omap_pm_runtime_suspend' was not declared. Should it be static?
arch/arm/mach-omap2/pm_bus.c:40:5: warning: symbol 'omap_pm_runtime_resume' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case on OMAP2+ we call set_24xx_gpio_triggering() instead of
updating reg and l values. However, at the end of the function we
perform a write:
__raw_writel(l, reg);
So on OMAP2+ we end up writing 0 to the bank->base which is not
correct (typically this points to GPIO_REVISION register).
Fix this by returning immediately after call to
set_24xx_gpio_triggering().
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
twl_init functions are declared in pm.h and used in pm.c
pm.h header defining the protos need to be included to
ensure that omap_twl.c has consistent function definition.
This fixes sparse warning:
arch/arm/mach-omap2/omap_twl.c:237:12: warning: symbol 'omap4_twl_init' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:256:12: warning: symbol 'omap3_twl_init' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The uv_to_vsel, vsel_to_uv functions don't need to be exposed to the
world as they are used as function pointers. make them static.
Fixes sparse warnings:
arch/arm/mach-omap2/omap_twl.c:63:15: warning: symbol 'twl4030_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:68:4: warning: symbol 'twl4030_uv_to_vsel' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:73:15: warning: symbol 'twl6030_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/omap_twl.c:105:4: warning: symbol 'twl6030_uv_to_vsel' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
omap_enable_smartreflex_on_init is meant to be used by boards
which would like to have SR enabled by default on the platform, while
omap_devinit_smartreflex is used by pm code, the protos are defined
in pm.h. This header should be included to ensure that sr_device
function definitions match the prototypes.
including pm.h fixes the sparse warnings (with CONFIG_OMAP_SMARTREFLEX=y):
arch/arm/mach-omap2/sr_device.c:138:13: warning: symbol 'omap_enable_smartreflex_on_init' was not declared. Should it be static?
arch/arm/mach-omap2/sr_device.c:143:12: warning: symbol 'omap_devinit_smartreflex' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
omap2_wd_timer_disable is declared in wdtimer.h and used by hwmod
function pointers for usage, the header inclusion is necessary
to ensure that the prototype and function remains consistent.
omap_wdt_latency is passed as a pointer and does not need global scope
Fixes sparse warnings:
arch/arm/mach-omap2/devices.c:981:31: warning: symbol 'omap_wdt_latency' was not declared. Should it be static?
arch/arm/mach-omap2/wd_timer.c:27:5: warning: symbol 'omap2_wd_timer_disable' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
igep3_flash_init is not used beyond the scope of the file, make it
static instead.
Fixes sparse warning:
arch/arm/mach-omap2/board-igep0030.c:106:13: warning: symbol 'igep3_flash_init' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_zoom_wlan_data and zoom2_set_hs_extmute are not used beyond
the scope of zoom-peripherals directly, instead pointers are used.
make them static instead.
Fixes sparse warnings:
arch/arm/mach-omap2/board-zoom-peripherals.c:193:29: warning: symbol 'omap_zoom_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:245:6: warning: symbol 'zoom2_set_hs_extmute' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux data is passed by pointers to mux.c from the SoC specific
mux file, these variables dont really need to be global scope.
This fixes the following sparse warnings:
arch/arm/mach-omap2/mux44xx.c:547:29: warning: symbol 'omap4_core_cbl_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux44xx.c:1265:29: warning: symbol 'omap4_core_cbs_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux44xx.c:1549:29: warning: symbol 'omap4_wkup_cbl_cbs_ball' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
memcpy() copies 8 bytes too much (omap_mux_entry vs. omap_mux). Correct
by replacing memcpy() with struct assignment, which is safer.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This option uses LDREXB/STREXB to emulate SWPB but these instructions
are not supported on all the ARMv6 processors.
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leif Lindholm <Leif.Lindholm@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (243 commits)
omap2: Make OMAP2PLUS select OMAP_DM_TIMER
OMAP4: hwmod data: Fix alignment and end of line in structurefields
OMAP4: hwmod data: Move the DMA structures
OMAP4: hwmod data: Move the smartreflex structures
OMAP4: hwmod data: Fix missing SIDLE_SMART_WKUP in smartreflexsysc
arm: omap: tusb6010: add name for MUSB IRQ
arm: omap: craneboard: Add USB EHCI support
omap2+: Initialize serial port for dynamic remuxing for n8x0
omap2+: Add struct omap_board_data and use it for platform level serial init
omap2+: Allow hwmod state changes to mux pads based on the state changes
omap2+: Add support for hwmod specific muxing of devices
omap2+: Add omap_mux_get_by_name
OMAP2: PM: fix compile error when !CONFIG_SUSPEND
MAINTAINERS: OMAP: hwmod: update hwmod code, data maintainership
OMAP4: Smartreflex framework extensions
OMAP4: hwmod: Add inital data for smartreflex modules.
OMAP4: PM: Program correct init voltages for scalable VDDs
OMAP4: Adding voltage driver support
OMAP4: Register voltage PMIC parameters with the voltage layer
OMAP3: PM: Program correct init voltages for VDD1 and VDD2
...
Fix up trivial conflict in arch/arm/plat-omap/Kconfig
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits)
ARM: DMA: add support for DMA debugging
ARM: PL011: add DMA burst threshold support for ST variants
ARM: PL011: Add support for transmit DMA
ARM: PL011: Ensure IRQs are disabled in UART interrupt handler
ARM: PL011: Separate hardware FIFO size from TTY FIFO size
ARM: PL011: Allow better handling of vendor data
ARM: PL011: Ensure error flags are clear at startup
ARM: PL011: include revision number in boot-time port printk
ARM: vexpress: add sched_clock() for Versatile Express
ARM i.MX53: Make MX53 EVK bootable
ARM i.MX53: Some bug fix about MX53 MSL code
ARM: 6607/1: sa1100: Update platform device registration
ARM: 6606/1: sa1100: Fix platform device registration
ARM i.MX51: rename IPU irqs
ARM i.MX51: Add ipu clock support
ARM: imx/mx27_3ds: Add PMIC support
ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn()
mx51: fix usb clock support
MX51: Add support for usb host 2
arch/arm/plat-mxc/ehci.c: fix errors/typos
...
Add ARM support for the DMA debug infrastructure, which allows the
DMA API usage to be debugged.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (35 commits)
mmc: msm_sdcc: Check for only DATA_END interrupt to end a request
mmc: msm_sdcc: Fix bug in PIO mode when data size is not word aligned
mmc: msm_sdcc: Reset SDCC in case of data transfer errors
mmc: msm_sdcc: Add prog done interrupt support
mmc: msm_sdcc: Fix possible circular locking dependency warning
MSM: Add USB support for MSM7x30
MSM: Add USB suport for QSD8x50
msm: initial framebuffer support
msm: add handling for clocks tagged as CLK_MINMAX
msm: trout: change name of pmdh_clk to mddi_clk
msm: add CLK_MINMAX to pmdh_clk
msm: trout: add gpio_to_irq
msm: iommu: Use the correct memory allocation flag
msm_serial: Remove redundant unlikely()
msm: iommu: Miscellaneous code cleanup
msm: iommu: Support cache-coherent memory access
msm: iommu: Definitions for extended memory attributes
msm: iommu: Kconfig dependency for the IOMMU API
msm: iommu: Check if device is already attached
msm: iommu: Kconfig item for cacheable page tables
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1436 commits)
cassini: Use local-mac-address prom property for Cassini MAC address
net: remove the duplicate #ifdef __KERNEL__
net: bridge: check the length of skb after nf_bridge_maybe_copy_header()
netconsole: clarify stopping message
netconsole: don't announce stopping if nothing happened
cnic: Fix the type field in SPQ messages
netfilter: fix export secctx error handling
netfilter: fix the race when initializing nf_ct_expect_hash_rnd
ipv4: IP defragmentation must be ECN aware
net: r6040: Return proper error for r6040_init_one
dcb: use after free in dcb_flushapp()
dcb: unlock on error in dcbnl_ieee_get()
net: ixp4xx_eth: Return proper error for eth_init_one
include/linux/if_ether.h: Add #define ETH_P_LINK_CTL for HPNA and wlan local tunnel
net: add POLLPRI to sock_def_readable()
af_unix: Avoid socket->sk NULL OOPS in stream connect security hooks.
net_sched: pfifo_head_drop problem
mac80211: remove stray extern
mac80211: implement off-channel TX using hw r-o-c offload
mac80211: implement hardware offload for remain-on-channel
...
Add a sched_clock() implementation to Versatile Express using the new
sched_clock() infrastructure for extending 32bit counters to full
64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prepare the ap4evb board for the MIPI DSI driver transition to support
different register layouts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now, that the MIPI DSI driver implements runtime PM, we don't need anymore to
configure clocks statically in the platform code. This patch also adds a DSITX1
clock definition for sh7372 and attaches PHY clocks to respective devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
1. pll_base address should return right value
2. uart parent clk is from pll3
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
