According to http://bugzilla.kernel.org/show_bug.cgi?id=6933
The latest BIOS for the P2B-S works fine.
Remove it from the blacklist.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix acpi_pm_device_sleep_state() to return the value returned
by _SxD if the device is supposed to wake up the system from
given sleep state and the evaluation of _SxW fails (e.g. _SxW
is not present).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.
But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.
Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.
So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.
http://bugzilla.kernel.org/show_bug.cgi?id=9194
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When PCI IDE controller works in legacy mode and no PRT entry is found
in ACPI PRT table, OSPM will neither read the irq number from the IDE
PCI configuration space nor call the function of acpi_register_gsi to
register gsi.
http://bugzilla.kernel.org/show_bug.cgi?id=5637
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Burst mode temporary (50 ms) locks EC to do only transactions with
driver, without it some hardware returns abstract garbage.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9341
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Specification allows only byte access for EC region, so
make it separate from bug-compatible multi-byte access.
Also do not allow return of garbage in supplied *value.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9341
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not
present [20060707]
According to the ACPI spec 6.3.7,
"If a device object (including the processor object) does not have an
_STA object, then OSPM assumes that all of the above bits are set,
(in other words, the device is present, enabled, shown in the UI
and funtioning)".
is_processor_present shoud return 1 if the processor device object exists
while it doesn't have an _STA object.
http://bugzilla.kernel.org/show_bug.cgi?id=8570
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This was writeable in 2.6.23 but the cpuidle merge made it read-only. But
some people's scripts (ie: Mark's) were writing to it.
As an unhappy compromise, make max_cstate writeable again if the kernel was
configured without CONFIG_CPU_IDLE.
http://bugzilla.kernel.org/show_bug.cgi?id=9683
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Some _STA methods called during bus_scan() might require EC region handler,
which might be enabled later in the scan.
Enable it explicitly before scan to avoid errors.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9627
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
/proc/acpi/alarm can't be set correctly, here is a sample:
[root@localhost /]# echo "2006 09" > /proc/acpi/alarm
[root@localhost /]# cat /proc/acpi/alarm
2007-12-09 09:09:09
[root@localhost /]# echo "2006 04" > /proc/acpi/alarm
[root@localhost /]# cat /proc/acpi/alarm
2007-12-04 04:04:04
[root@localhost /]#
Obviously, it is wrong, it should consider it as an invalid input.
after this patch:
[root@localhost /]# echo "2008 09" > /proc/acpi/alarm
-bash: echo: write error: Invalid argument
[root@localhost /]#
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In function acpi_system_write_alarm in file drivers/acpi/sleep/proc.c,
big sec, min, hr, mo, day and yr are counted twice to get reasonable
values, that is very superfluous, we can do that only once.
In additon, /proc/acpi/alarm can set a related value which can be
specified as YYYY years MM months DD days HH hours MM minutes SS
senconds, it isn't a date, so you can specify as +0000-00-00 96:00:00
, that means 3 days later, current code can't handle such a case.
This patch removes unnecessary code and does with the aforementioned
situation.
Before applying this patch:
[root@localhost /]# cat /proc/acpi/alarm
2007-12-00 00:00:00
[root@localhost /]# echo "0000-00-00 96:180:180" > /proc/acpi/alarm
[root@localhost /]# cat /proc/acpi/alarm
0007-12-02 **:**:**
[root@localhost /]#
After applying this patch:
[root@localhost ~]# echo "2007-12-00 00:00:00" > /proc/acpi/alarm
[root@localhost ~]# cat /proc/acpi/alarm
2007-12-00 00:00:00
[root@localhost ~]# echo "0000-00-00 96:180:180" > /proc/acpi/alarm
[root@localhost ~]# cat /proc/acpi/alarm
0007-12-04 03:03:00
[root@localhost ~]#
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
klaptopd assumes rate to be in same units as capacity.
http://bugzilla.kernel.org/show_bug.cgi?id=9362
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Alarm bit should be cleared in order for other alarms to be sent.
http://bugzilla.kernel.org/show_bug.cgi?id=9362
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI tables follow a tree structure in memory.
The root of the tree is the RSDP (Root System Description Pointer).
To find the RSDP, the OS searches for the signature "RSD PTR "
in well known physical memory locations. Then the OS computes
a table checksum to verify that the signature is really part
of a valid table header.
Some systems have a proper signature but an invalid checksum;
followed elsewhere by a proper signature with valid checksum.
http://bugzilla.kernel.org/show_bug.cgi?id=9444
The Linux RSDP scanning code bailed out on those systems
and as a result they booted with ACPI disabled.
Fix this by deleting the Linux RSDP scanning code and
plugging in the ACPICA RSDP scanning code.
Signed-off-by: Len Brown <len.brown@intel.com>
More aggressively request deep C-states.
Note that the job of the OS is to minimize latency
impact to expected break events such as interrupts.
It is not the job of the OS to try to calculate if
the C-state will reach energy break-even.
The platform doesn't give the OS enough information
for it to make that calculation. Thus, it is up
to the platform to decide if it is worth it to
go as deep as the OS requested it to, or if it
should internally demote to a more shallow C-state.
But the converse is not true. The platform can not
promote into a deeper C-state than the OS requested
else it may violate latency constraints. So it is
important that the OS be aggressive in giving the
platform permission to enter deep C-states.
Signed-off-by: Len Brown <len.brown@intel.com>
for sn2_defconfig:
WARNING: vmlinux.o(.text+0x4b8601): Section mismatch: reference to .init.data:node_to_pxm_map (between '__acpi_map_pxm_to_node' and 'acpi_get_pxm')
WARNING: vmlinux.o(.text+0x4b8741): Section mismatch: reference to .init.data:pxm_to_node_map (between 'acpi_map_pxm_to_node' and 'acpi_get_node')
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ->cap fields of struct acpi_video_device and struct acpi_video_bus
are 1B each, not 4B. The oversized memset()'s corrupted the subsequent
list_head fields. This resulted in silent corruption without
CONFIG_DEBUG_LIST and BUG's with it. This patch uses sizeof() to pass
the proper bounds to the memset() calls and thereby correct the bugs.
Signed-off-by: William Irwin <wli@holomorphy.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Len Brown <len.brown@intel.com>
References: https://bugzilla.novell.com/show_bug.cgi?id=302482
Signed-off-by: Thomas Renninger <trenn@novell.com>
Signed-off-by: Kay Sievers <kasievers@novell.com>
Signed-off-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
References: https://bugzilla.novell.com/show_bug.cgi?id=302482
Due to the new autloading of acpi drivers, the dock driver
wasn't loaded anymore as there is no HID to identify it with
(dock is needed if ACPI has a _DCK method).
This patch is a workaround for this, original by Thomas Renninger,
revised first by Kay Sievers and last by Frank Seidel.
V2 of this patch fixed problems on systems without a defined _CID for
the docking devices.
Signed-off-by: Thomas Renninger <trenn@novell.com>
Signed-off-by: Kay Sievers <kasievers@novell.com>
Signed-off-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
The timer broadcast code might access HPET, which should not be
accessed after the busmaster disable.
In acpi_idle_enter_simple() this change also prevents, that we modify
the busmaster state without going actually idle. This might leave the
ACPI bm state in a stale state, when we leave the function early in
the need_resched() check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
module parameter is used to prevent the thermal_zone action upon
critical trip points.
But exporting this notification to userspace is still useful.
By setting nocrt with this patch applied, ACPI will take no action
but exporting the events to userspace upon critical/hot trip points.
http://bugzilla.kernel.org/show_bug.cgi?id=9139
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
At least some systems report technology information with trailing spaces:
{pts/1}% cat -E /var/tmp/bat/2.6.23 | grep type
battery type: Li-ION $
Use strncasecmp to compare model string to skip trailing part
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Level GPE should not be enabled until all work caused by it is done,
e.g. all Notify() methods are completed.
This can be accomplished by appending enable_gpe function to the end
of notify queue.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Changed resolution of named references in packages
Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.
http://bugzilla.kernel.org/show_bug.cgi?id=5328http://bugzilla.kernel.org/show_bug.cgi?id=9429
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.
This fixes an oops on T61 -- a regression due to
f79f06ab9f b/c FixedHW support tried to read remote MSR with interrupts disabled.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.
The pointers to per cpu data are typically not initialized for processors
that are not present. So we seem to be reading something here from offset
0 in memory.
Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.
Convert one loop to NR_CPUS to use the cpu_possible map instead. That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix APIC related bootup crash on Athlon XP CPUs
time: add ADJ_OFFSET_SS_READ
x86: export the symbol empty_zero_page on the 32-bit x86 architecture
x86: fix kprobes_64.c inlining borkage
pci: use pci=bfsort for HP DL385 G2, DL585 G2
x86: correctly set UTS_MACHINE for "make ARCH=x86"
lockdep: annotate do_debug() trap handler
x86: turn off iommu merge by default
x86: fix ACPI compile for LOCAL_APIC=n
x86: printk kernel version in WARN_ON and other dump_stack users
ACPI: Set max_cstate to 1 for early Opterons.
x86: fix NMI watchdog & 'stopped time' problem
AMD Opteron processors before CG revision don't like C-states > 1.
This solves the long standing bugzilla #5303 and probably some more
on affected machines:
http://bugzilla.kernel.org/show_bug.cgi?id=5303
[ tglx@linutronix.de: reworked the patch so it does not wreck ia64 ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e736), which did only read address.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Tested-by: Mats Johannesson
Signed-off-by: Len Brown <len.brown@intel.com>
Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In cases where acpi_pci_bind() does not
attach device data, acpi_pci_unbind()
complains via an ACPI exception about the missing data when
the device is removed. For example, acpi_pci_bind() does not
attach data for non-existent device functions so when the device
is removed using the ACPI PCI hotplug driver 'acpiphp' an ACPI
exception is logged for every non-existent function. This patch
avoids the confusing log messages by removing the unnecessary
ACPI exception.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
GPEs are disabled depending on their type --
WAKE, WAKE_RUN, and RUNTIME. An error is returned
if we are asked to disable a GPE that has no type.
But at least one system exists that enables a GPE from AML
that is not the EC GPE, and has no _Lxx/_Exx AML handler,
and is thus never initialized.
In this case, when an external CRT is plugged in,
the GPE fires, we attempt to disable the GPE,
but instead just return an error.
So the GPE stays asserted and an ACPI interrupt storm follows.
The fix is to disable a firing GPE,
even if it comes from outer space.
http://bugzilla.kernel.org/show_bug.cgi?id=6217
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355
cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Port 2aa44d0567
(sched: sched_clock_idle_[sleep|wakeup]_event()) to cpuidle.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Port 18eab85503
(Enable C3 even when PM2_control is zero) to cpuidle.
Without this patch, some systems will notice a regression
when enabling CPU_IDLE -- C3 would no longer be available.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add debug tracing support during certain AML method execution.
Four more module parameters are created under /sys/module/acpi/parameters/:
trace_method_name: the AML method name that user wants to trace
trace_debug_layer: the temporary debug_layer used when tracing the method.
Using 0xffffffff by default if it is 0.
trace_debug_level: the temporary debug_level used when tracing the method.
Using 0x00ffffff by default if it is 0.
trace_state: The status of the tracing feature.
"enabled" means this feature is enabled
and the AML method is traced every time it's executed.
"1" means this feature is enabled and the AML method
will only be traced during the next execution.
"disabled" means this feature is disabled.
Users can enable/disable this debug tracing feature by
"echo string > /sys/module/acpi/parameters/trace_state".
"string" should be one of "enable", "disable" and "1".
http://bugzilla.kernel.org/show_bug.cgi?id=6629
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce new ACPI_PROCFS_POWER (default Yes) config option and move
procfs code in battery, ac, and sbs drivers under it.
This is done to allow ACPI_PROCFS to be default No.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
In order to be able to write the value "100"
to /proc/acpi/video/.../brightness, we have to allocate 5 bytes:
4 characters will be written (1, 0, 0 plus null byte),
and 1 byte should be buffer for a terminating NULL character.
http://bugzilla.kernel.org/show_bug.cgi?id=9278
Signed-off-by: Danny Baumann <dannybaumann@web.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some controllers fail to send confirmation GPE after address write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e736), which did only read address.
http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/sbs.c: In function acpi_battery_add:
drivers/acpi/sbs.c:811: warning: ignoring return value of device_create_file,
declared with attribute warn_unused_result
Additional cleanups:
* use struct acpi_battery in acpi_battery_remove() to clean up function
calls, just like acpi_battery_add() already does.
* put braces around unregister call, as it depends on dev being not NULL.
* remove unneeded braces
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Add throttling control via MSR when T-states uses
the FixHW Control Status registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_TSS was erroneously ignored, in favor of the FADT.
When TSS is used, the access width is included in the PTC control/status
register. So it is unnecessary that the access bit width is multiplied by 8.
At the same time the bit_offset should be considered for system I/O Access.
It should be checked the bit_width and bit_offset of PTC regsiter in order to
avoid the failure of system I/O access. It means that bit_width plus
bit_offset can't be greater than 32.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change the function interface for throttling control via PTC.
The following functions are concerned:
acpi_read_throttling_status()
acpi_write_throttling_state()
acpi_get_throttling_value()
acpi_get_throttling_state()
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Factor out legacy FADT.duty_width code
and run it only in the non _TSS case.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We've run into BIOS that hand us 4-bit access width requests
for T-state control when the code expected only multipls of 8-bits.
Round up.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When a T-state limit change notification is received,
Linux must evaluate _TPC and change its current
T-state immediately to comply with the new limit.
Previously, Linux would notice the new limit
only upon the next throttling change.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Check if AC state has changed across resume and notify userspace if so.
Fixes "[2.6.24-rc1 regression] AC adapter state does not change after resume"
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not provide /proc/acpi/ac_adapter if ACPI_PROCFS is not defined. This
eliminates duplicated power adapters in HAL and makes it consistent with
battery module
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zillions of people are getting my-battery-monitor-doesnt-work problems
(including me).
Lessen the damage by making ACPI_PROCFS default to on.
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
list_for_each_safe() only protects list from list alterations
performed by the same thread. One still needs to implement
proper locking when list is being accessed from several threads.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If input_register_device() fails input_free_device() must
be called to release memory allocated for the device.
Also consolidate error handling in acpi_bus_video_add()
and handle input_allocate_device() failures.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Properly set up parent on input device registered by the video driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
get_property() should not call battery_update(), it also should call
get_status() only if battery is present to avoid cycle and oops.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add documentation in Kconfig help about the move of /proc/acpi/battery
to /sys/class/power_supply when selecting ACPI_PROCFS. This will impact
a lot of users and should be documented.
Signed-off-by: Jerome Pinot <ngc891@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a battery is at a critical charge level and not being charged or
discharged, then the ACPI _BST method will return a state of 4, and
the current acpi_battery_get_property() code will not set any property
value for POWER_SUPPLY_PROP_STATUS. This will cause an oops in
power_supply_show_property() when it reads off the end of the
status_text array. This actually was causing a 100% reproducible
crash on boot on my laptop with two batteries, when one battery was
completely drained and the laptop was not plugged in.
Fix this by making sure acpi_battery_get_property() returns
POWER_SUPPLY_STATUS_UNKNOWN for any battery state it doesn't already
handle explicitly. There doesn't seem to be any status enum value
defined that makes more sense than 'unknown' for a battery at a
critical charge level.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <lenb@t61.(none)>
Current description for CONFIG_ACPI includes the word "Support" twice. One
effect of this is that in menuconfig the "--->" that indicates the presence
of sub-options will not show up unless you have a very wide console.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
POWER_SUPPLY is needed for AC, battery, and SBS sysfs support. Use
'select' instead of 'depends on', as it is will not be selected by anything
else, leading to confusion.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Some machines return integer instead of expected string.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
Support Li-Ion as possible name for technology.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure no power_supply object is present unless we actualy detect
presence of battery. This fixes ghost batteries detected by HAL
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes some totally illogical and wrong code that converts things to
and from BCD mode essentially randomly, does math on values in BCD mode
etc etc. Introduce a few helper functions to make it a bit more obvious
what is going on, and make sure that we always do all the arithmetic
(and anythign else, for that matter) in binary, not BCD.
Tested by Mark Lord, who found the problem originally, and also pushed
the patch back and reminded me about it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
