The new names tell the image resolution: 'Scale' is the smaller image.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change fixes up saa7127_s_std() generate SECAM out, if the user has
requested a 50 Hz video standard set that only contains a request for SECAM
standards and not PAL. Only the SAA712[89] chips can generate SECAM, the
SAA712[67] chips cannot.
I was unclear on the burst start and end values - I couldn't figure out
the units - so I left them the same as for the PAL systems.
A the video decoders on both a PVR-350 (SAA7115) and an HVR-1600 (CX23418)
identify the SECAM signal generated by a SAA7129 with this patch as SECAM.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the "xceive_pin" setting from "15" to "1" for the PVR2100 -- the same as
the PVR3100H. This properly resets the XC2028 tuner on the PVR2100.
Sergey's original email report:
Hi.
Seems cx18 module has incorrect .xceive_pin value for card,
as i see lots of i2c errors in dmesg from xc2028.
i'm using 2.6.32.2, my hardware is:
00:09.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23418
Single-Chip MPEG-2 Encoder with Integrated Analog Video/Broadcast Audio Decoder
[14f1:5b7a]
Subsystem: LeadTek Research Inc. Device [107d:6f27]
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at f0000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Kernel driver in use: cx18
Kernel modules: cx18
Following fixes this problem for me, the rest seems working:
Reported-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Tested-by: Sergey Bolshakov <sbolshakov@altlinux.ru>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX18_CPU_SET_INDEXTABLE command was being called with the wrong number
of arguments causing the index table frame type selection mask to be set wrong.
Now the IDX stream properly sends entries for I, P, and B frames.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_G_ENC_INDEX support see the light of day.
Some notes:
1. With default capture parameters, the CX23418 seems to transfer 192 index
entries (4.5 kB worth) at 10 second intervals.
2. Index streams don't seem to be supported for MPEG 2 TS streams
3. The index entries seem to claim every frame is a B-Frame. Possible
firmware bug.
4. The cx18 driver does not try to capture an index stream when inserting
sliced VBI into the MPEg stream as the offsets would need fixup.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the v4l2 spec, very old MPEG index entries needs to be discarded
in favor of newer index entries. This change ensures the firmware always has
buffers for index entries at the expense of the oldest unread buffers.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change starts the IDX stream along with the MPG stream as an internal
use (only) stream much like the VBI stream can be started as an internal use
stream for inserting sliced VBI packets.
The IDX stream is not started automatically with an MPEG strem if the IDX
stream is disabled (no buffers allocated) or if sliced VBI insertion is being
performed by the cx18 driver. The cx18 driver doing sliced VBI insertion
makes the offsets in the IDX stream inaccurate for the final MPEG stream
presented to user space. Since fixing the IDX offsets ourselves is not easy
and we cannot easily do what ivtv does to fix the offsets, we'll make sliced
VBI insertion and MPEG Index capture mutually exclusive for now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change allows the IDX stream to be started and stopped as any other
stream even though it has no associated device node. This is needed for
cx18 driver internal use.
Also always tell the CX23418 to generate index entries when an analog capture
starts and the IDX stream has had buffers allocated (i.e. is enabled).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a long standing memory leak of stream buffers for streams that did not
have a struct video_device allocated: namely the TS and IDX streams.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the module options related to INDEX stream buffer allocation. A single
CX2341[5678] index entry is only 24 bytes. Large buffers for the IDX stream
will prevent the CX23418 from transferring index data over at all. Buffers
of around 1.5 kB or 64 index entries seem to be just fine. We'll default to
63 buffers/MDLs as that is the firmware limit per stream and IDX stream buffers
are not high rate. There is no reason on earth to allocate the previous 1 MB
default of buffer space for the IDX stream.
This is in anticipation of implementing the G_ENC_INDEX ioctl() in the cx18
driver.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ctrls field of struct sd_desc is declared as const
in gspca.h. It is worth to initialize the content also with
constant values.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function callbacks in sd_desc are defined at compile time and
they do not change at runtime. Make the sd_desc initializations const.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB video interface was checked as having the number zero, but
some webcams have other values. The test is now done on the interface
class which may be either 255 (vendor spec) or 0 (class per interface).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- adapt the start sequences from the info file of the ms-win driver
of the webcams 046d:08a2/046d:08aa (lvWIMv.inf)
- disable the brightness for this sensor
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- have 2 tables for sensor probe
- with the same ID, the sensor mi1320 is found with the bridge vc0321,
the sensor mi1320_soc with the bridge vc0323
- add some comments
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added a new initialization method for Aiptek DV T300.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13708
Tested-by: Hámorszky Balázs <balihb@gmail.com>
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently all probed sensor types are emitted in the kernel log, generating unnecessary noise. Be less verbose and only report what sensor is found (if any)
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcam 0ac8:303b may have the sensors HV7131B or HV7131R(c).
This changeset checks the HV7131 type.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ID was found in a webcam 0ac8:301b.
Signed-off-by: Luis Maia <lmaia@royalhat.org>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This flag permits subdrivers to create specific transfer URBs.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/buildtest/v4l-dvb-master/v4l/ir-keytable.c: In function 'ir_setkeycode':
/home/v4l/buildtest/v4l-dvb-master/v4l/ir-keytable.c:190: warning: 'newkeymap' may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, if RF is locked but demod is not locked, it will report:
>>> tuning status == 0x03
This happens, for example, if the device is on DVB-T, and the video
standard is ISDB-T.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After taking a look at the driver's history and doing some tests with
DVB and ISDB-T, it was noticed that the stats were incomplete, for
ISDB-T, and weren't working for DVB.
Fixed the code and added a debug code to print the complete stats at
dmesg. This debug is useful to improve the stats of this driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on a patch originally written by Michael Krufky <mkrufky@linuxtv.org>
for a preliminar S2API spec.
The patch were ported to the S2API and had the ISDB-T API additions to
honor the auto mode, while keep allowing manual tuning.
Tested with both the original dvb-apps and the new dvb-apps-isdbt scan,
that uses a different channel.conf and uses S2API with ISDB-T extensions.
Thanks-to: Michael Krufky <mkrufky@linuxtv.org> for his first version
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Siano series of patches seemed to cause a regression on reporting DTV
statistics. Due to that, signal indication weren't received, preventing
applications like scan to work.
Tested with ISDB-T signals and got the same scan result as with a
dib0700/dib8000 device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Activate ISDB-T mode using module option default_mode=6.
hack: use 4 lower bits in frequency for segment number
[mchehab@redhat.com: fix merge conflicts and CodingStyle]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improves ATBM8830 reception by using per card AGC configuration rather
than register default.
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some unknown reason, on a MacBookPro5,3 the iSight sometimes report
a different video format GUID. This patch add the other (wrong) GUID to
the format table, making the iSight work always w/o other problems.
What it should report: 32595559-0000-0010-8000-00aa00389b71
What it often reports: 32595559-0000-0010-8000-000000389b71
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The quirks module parameter is or'ed with the built-in quirks for the
device being probed. This make it impossible to disable a built-in quirk
without recompiling the driver.
Replace the built-in quirks with the quirks module parameter instead of
or'ing the values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The realtime clock provided by do_gettimeofday() is affected by time
jumps caused by NTP or DST. Furthermore, preliminary investigation
showed that SMP systems the realtime clock is based on the CPU TSC,
and those could get slightly out of sync, resulting in jitter in the
timestamps depending on which processor handles the USB interrupts.
Instead of the realtime clock, use a monotonic high resolution clock to
timestamp the buffer. As this could in theory introduce a regression
with some userspace applications expecting a realtime clock timestamp,
add a module parameter to switch back to the realtime clock.
Thanks to Paulo Assis for pointing out and investigating the issue.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As currently most drivers don't define ir_dev->props, we shouldn't assume
that this field is defined.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on stv0903 demod, stb6100 tuner.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When preparing the linux-next patches, I got those errors:
include/media/ir-core.h:29: warning: left shift count >= width of type
In file included from include/media/ir-common.h:29,
from drivers/media/video/ir-kbd-i2c.c:50:
drivers/media/video/ir-kbd-i2c.c: In function ‘ir_probe’:
drivers/media/video/ir-kbd-i2c.c:324: warning: left shift count >= width of type
Unfortunately, enum is 32 bits on i386. As we define IR_TYPE_OTHER as 1<<63,
it won't work on non 64 bits arch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Experimental patch to allow changing the IR protocol. Currently, it support
changing between RC-5 and NEC protocols.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds an structure to ir_input_register to contain IR device characteristics,
like supported protocols and a callback to handle protocol event changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add sysfs skeleton to export remote controller information via
/sys/class/irrcv.
For now, the code doesn't do much. It just exports an attribute that
is meant to report and control the IR protocol used by the keytable.
However, the callbacks for this new attribute weren't set yet.
Also, it lacks symlinks to the used event interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move I2C IR initialization from just after I2C bus setup to right
before non-I2C IR initialization. This avoids the case where an I2C IR
device is blocking audio support (at least the PV951 suffers from
this). It is also more logical to group IR support together,
regardless of the connectivity.
This fixes bug #15184:
http://bugzilla.kernel.org/show_bug.cgi?id=15184
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Regression was caused by my commit 6b35ca0d3d
which determined message size using sizeof rather than hardcoded constants.
Unfortunately pwc_set_shutter_speed reuses a 2 byte buffer for a one byte
message too so the sizeof was bogus in this case.
All other uses of sizeof checked and are ok.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This polling is needed if camera is in standby mode, but current exiting
condition is inverted.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cxusb uses the atbm8830 and lgs8gxx (not lgs8gl5) frontends and the
max2165 tuner, so it needs to select them.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I'm trying to fix it on the GCC side (PR43007), but the module is
quite stupid in using ULL constants to operate on u32 values:
static int apply_frontend_param (struct dvb_frontend* fe, struct
dvb_frontend_parameters *param)
{
...
static const u32 ppm = 8000;
u32 spi_bias;
...
spi_bias *= 1000ULL;
spi_bias /= 1000ULL + ppm/1000;
which causes current GCC 4.5 to emit calls to __udivdi3 for i?86 again.
This patch fixes this issue.
Signed-off-by: Richard Guenther <rguenther@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A DVB demultiplexer device can be used to set up either a PES filter or
a section filter. In the former case, the ts field of the feed union of
struct dmxdev_filter is used, in the latter case the sec field of the
same union is used.
The ts field is a struct list_head, and is currently initialized in the
open() method of the demux device. When for a given demuxer a section
filter is set up, the sec field is played with, thus if a PES filter
needs to be set up after that the ts field will be corrupted, causing a
kernel oops.
This fix moves the list head initialization to
dvb_dmxdev_pes_filter_set(), so that the ts field is properly
initialized every time a PES filter is set up.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Cc: stable <stable@kernel.org>
Reviewed-by: Andy Walls <awalls@radix.net>
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As dvb_dmx_swfilter_packet() is protected by a spinlock, it shouldn't sleep.
However, vmalloc() may call sleep. So, move the initialization of
dvb_demux::cnt_storage field to a better place.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb_dmx_init tries to allocate virtual memory for 2 pointers: filter and feed.
If the second vmalloc fails, filter is freed, but the pointer keeps pointing
to the old place. Later, when dvb_dmx_release() is called, it will try to
free an already freed memory, causing an OOPS.
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An earlier commit removed the lock_kernel/unlock_kernel pair but forgot
to remove the unlock_kernel call in the cleanup path at the end of the
function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'mantis' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (117 commits)
V4L/DVB (13851): Fix Input dependency for Mantis
V4L/DVB(13824a): mantis: Fix __devexit bad annotations
V4L/DVB (13808b): mantis: replace DMA_nnBIT_MASK to DMA_BIT_MASK(32)
V4L/DVB (13808): [Mantis/Hopper] Build update for Mantis/Hopper based cards
V4L/DVB(13808a): mantis: convert it to the new ir-core register/unregister functions
V4L/DVB (13812): [Mantis/Hopper] Update Copyright header
V4L/DVB (13811): [MB86A16] Update Copyright header
V4L/DVB (13810): [MB86A16] Use DVB_* macros
V4L/DVB (13809): Fix Checkpatch violations
V4L/DVB (13807): Fix: Free device in the device registration failure case
V4L/DVB (13806): Register and Initialize Remote control
V4L/DVB (13805): Fix: Unregister the frontend before detaching
V4L/DVB (13804): Remove unused I2C Adapter ID
V4L/DVB (13803): Remove unused dependency on CU1216
V4L/DVB (13802): [Mantis/Hopper] Fix all build related warnings
V4L/DVB (13801): [MB86A16] Use the search callback
V4L/DVB (13800): [Mantis] I2C optimization. Required delay is much lesser than 1mS.
V4L/DVB (13799): [Mantis] Unregister frontend
V4L/DVB (13798): [Mantis] Enable power for all cards, use byte mode only on relevant devices
V4L/DVB (13797): [Mantis/Hopper/TDA665x] Large overhaul,
...
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x13d7): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x1433): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x185e): Section mismatch in reference from the function hopper_pci_probe() to the function
.devexit.text:mantis_i2c_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/mantis/built-in.o(.devinit.text+0x18ba): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x68b8): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x6914): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x6d3f): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/dvb/built-in.o(.devinit.text+0x6d9b): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14634): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14690): Section mismatch in reference from the function mantis_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit mantis_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14abb): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_i2c_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_i2c_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_i2c_exit() so it may be used outside an exit section.
WARNING: drivers/media/built-in.o(.devinit.text+0x14b17): Section mismatch in reference from the function hopper_pci_probe() to the function .devexit.text:mantis_pci_exit()
The function __devinit hopper_pci_probe() references
a function __devexit mantis_pci_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
mantis_pci_exit() so it may be used outside an exit section.
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/mantis/mantis_pci.c: In function ‘mantis_pci_init’:
drivers/media/dvb/mantis/mantis_pci.c:76: warning: ‘DMA_nnBIT_MASK’ is deprecated
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Matthias Wachter <mathias@waechter.wiz.at>
for pointing it out.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Initial go at VP-3028, VP-3030 devices.
* I2C communication improvements,
* Add TDA665x support
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not rely on the PCI ID alone
Signed-off-by: Niklas Edmundsson <nikke@acc.umu.se>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Viitamaki <mau2@suomi24.fi>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
do not use the event manager to handle the fast events
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Ershov and Igor for pointing it out.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dnumgis got hit with this bug, using a temporary workaround
for the time being rather than digging deep at this point.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
(Need to sanitize this cleanly for different Slaves)
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Magnus Horlin <magnus@alefors.se>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to hotwings <user.vdr@gmail.com> for pointing out the bug
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Demodulator status check made reliable
* Code simplification for Viterbi Sync check, makes
acquisition more reliable
* Implement a BER monitor
* Implement a Signal strength monitor
* Implement a "simple" UCB monitor, no real UCB monitor
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
You know, the worst endianness errors are not the cases where
people forget to byte-swap, but the cases where they either byte-swap
with the wrong size, or byte-swap when they shouldn't have done so at
all. Those ones defeat the casual reader of the code.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some customers has problem with quality of DVB-T
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/446575
After this patch http://patchwork.kernel.org/patch/23345/
This is patch for fix regression with DVB-T. Tested with many people.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the following compiler warning: 'dummy' is used uninitialized in this function.
Although the result in the dummy variable is not used the program flow in
soc_camera_limit_side() depends on the value in dummy. The program flow is better
to be deterministic.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Cc: David Vrabel <dvrabel@arcom.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Cc: David Vrabel <dvrabel@arcom.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: linux-media@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Quickcam Web camera would not produce an image if you removed and inserted the module multiple times without physically power cycling the camera first.
By writing zero to bridge register STV_SCAN_RATE (0x1443) the camera works as intended, regardless of the number of module insertions.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a vflip quirk for the Fujitsu-Siemens Amilo Xi 2428. Thanks to Myroslav Zapukhlyak for reporting.
Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frame pointer returned by get_i_frame may be NULL when the application
is too slow.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This warning prevented the sharpness setting to work with the ov965x sensor.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Randy Dunlap <randy.dunlap@oracle.com>:
> drivers/media/dvb/frontends/dib8000.h:104: error: expected expression before '}' token
> drivers/media/dvb/frontends/dib8000.h:104: warning: left-hand operand of comma expression has no effect
>
> return CT_SHUTDOWN,
>
> s/,/;/ and fix indentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Buffers were marked as done before being removed from the IRQ queue. If
a userspace application dequeued and requeued the buffer fast enough
during that time window, the buffer could end up being deleted twice,
generating an oops in interrupt context.
Add a new state, UVC_BUF_STATE_READY, to mark buffers as ready for reuse
but not yet removed from the queue, and transition to UVC_BUF_STATE_DONE
only when the buffer is removed from the queue.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unlike assumed by the driver, alternate settings are not sorted by
endpoint max packet size. Iterate over all alternate settings to find
the one with the smallest compatible max packet size.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control blacklisting code erroneously used usb_match_id() by passing
a pointer to a usb_device_id structure instead of an array of such
structures.
Replace the usb_match_id() call by usb_match_id_one().
Thanks to Paulo Assis for diagnosing the bug and providing an initial
fix.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make one-bit bitfields unsigned which will remove the following
sparse warning messages (see "make C=1"):
* lgdt3305.h:57:21: error: dubious one-bit signed bitfield
* lgdt3305.h:60:26: error: dubious one-bit signed bitfield
* lgdt3305.h:63:19: error: dubious one-bit signed bitfield
Signed-off-by: Nemeth Marton <nm127@freemail.hu>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When not set, some images could be lost.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control of more than one AV/C device at once --- e.g. camcorders, tape
decks, audio devices, TV tuners --- failed or worked only unreliably,
depending on driver implementation. This affected kernelspace and
userspace drivers alike and was caused by firewire-core's inability to
accept multiple registrations of FCP listeners.
The fix allows multiple address handlers to be registered for the FCP
command and response registers. When a request for these registers is
received, all handlers are invoked, and the Firewire response is
generated by the core and not by any handler.
The cdev API does not change, i.e., userspace is still expected to send
a response for FCP requests; this response is silently ignored.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changelog, rebased, whitespace)
Fix the cx23888 driver to use the new kfifo API. Using kfifo_reset()
may result in a possible race conditions. This patch fixes it by using
a spinlock around the kfifo_reset() function.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Reviewed-by: Andy Walls <awalls@radix.net>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the "ignoring return value of '...', declared with attribute
warn_unused_result" compiler warning in several users of the new kfifo
API.
It removes the __must_check attribute from kfifo_in() and
kfifo_in_locked() which must not necessary performed.
Fix the allocation bug in the nozomi driver file, by moving out the
kfifo_alloc from the interrupt handler into the probe function.
Fix the kfifo_out() and kfifo_out_locked() users to handle a unexpected
end of fifo.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rename kfifo_put... into kfifo_in... to prevent miss use of old non in
kernel-tree drivers
ditto for kfifo_get... -> kfifo_out...
Improve the prototypes of kfifo_in and kfifo_out to make the kerneldoc
annotations more readable.
Add mini "howto porting to the new API" in kfifo.h
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver needs to #include <sched.h>:
drivers/media/radio/si470x/radio-si470x-common.c:452: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/media/radio/si470x/radio-si470x-common.c:452: error: implicit declaration of function 'signal_pending'
drivers/media/radio/si470x/radio-si470x-common.c:452: error: implicit declaration of function 'schedule'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the local filter coefficients static and const. This will eliminate the
following sparse warnings (see "make C=1"):
* au8522_decoder.c:71:31: warning: symbol 'filter_coef' was not declared. Should it be static?
* au8522_decoder.c:113:31: warning: symbol 'lpfilter_coef' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gpio field in the cx231xx_board.input structure is a pointer. Eliminate the
following sparse warnings (see "make C=1"):
* cx231xx-cards.c:72:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:77:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:84:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:111:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:116:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:123:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:151:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:156:13: warning: Using plain integer as NULL pointer
* cx231xx-cards.c:163:13: warning: Using plain integer as NULL pointer
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sizeof(print_buf) is just the size of the pointer. Change it to the size
used in the allocation of print_buf earlier in the same function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Cc: Janne Grunau <j@jannau.net>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove duplicated line on driver
[mchehab@redhat.com: second hunk of the original patch were already applied by another patch - remove it]
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Duncan Gibb <dg@duncangibb.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Make module_init static and mark it with __init.
Make module_exit static and mark it with __exit.
Mark probe functions with __devinit.
Make id table static and mark with __devinitconst.
This will eliminate the following sparse warnings (see "make C=1"):
* smsdvb.c:668:5: warning: symbol 'smsdvb_module_init' was not declared. Should it be static?
* smsdvb.c:682:6: warning: symbol 'smsdvb_module_exit' was not declared. Should it be static?
* smsusb.c:491:22: warning: symbol 'smsusb_id_table' was not declared. Should it be static?
* smsusb.c:567:5: warning: symbol 'smsusb_module_init' was not declared. Should it be static?
* smsusb.c:578:6: warning: symbol 'smsusb_module_exit' was not declared. Should it be static?
* smssdio.c:341:5: warning: symbol 'smssdio_module_init' was not declared. Should it be static?
* smssdio.c:353:6: warning: symbol 'smssdio_module_exit' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Eliminate the following sparse warnings (see "make C=1"):
* dib8000.c:125:15: warning: symbol 'coeff_2k_sb_1seg_dqpsk' was not declared. Should it be static?
* dib8000.c:130:15: warning: symbol 'coeff_2k_sb_1seg' was not declared. Should it be static?
* dib8000.c:134:15: warning: symbol 'coeff_2k_sb_3seg_0dqpsk_1dqpsk' was not declared. Should it be static?
* dib8000.c:139:15: warning: symbol 'coeff_2k_sb_3seg_0dqpsk' was not declared. Should it be static?
* dib8000.c:144:15: warning: symbol 'coeff_2k_sb_3seg_1dqpsk' was not declared. Should it be static?
* dib8000.c:149:15: warning: symbol 'coeff_2k_sb_3seg' was not declared. Should it be static?
* dib8000.c:154:15: warning: symbol 'coeff_4k_sb_1seg_dqpsk' was not declared. Should it be static?
* dib8000.c:159:15: warning: symbol 'coeff_4k_sb_1seg' was not declared. Should it be static?
* dib8000.c:164:15: warning: symbol 'coeff_4k_sb_3seg_0dqpsk_1dqpsk' was not declared. Should it be static?
* dib8000.c:169:15: warning: symbol 'coeff_4k_sb_3seg_0dqpsk' was not declared. Should it be static?
* dib8000.c:174:15: warning: symbol 'coeff_4k_sb_3seg_1dqpsk' was not declared. Should it be static?
* dib8000.c:179:15: warning: symbol 'coeff_4k_sb_3seg' was not declared. Should it be static?
* dib8000.c:184:15: warning: symbol 'coeff_8k_sb_1seg_dqpsk' was not declared. Should it be static?
* dib8000.c:189:15: warning: symbol 'coeff_8k_sb_1seg' was not declared. Should it be static?
* dib8000.c:194:15: warning: symbol 'coeff_8k_sb_3seg_0dqpsk_1dqpsk' was not declared. Should it be static?
* dib8000.c:199:15: warning: symbol 'coeff_8k_sb_3seg_0dqpsk' was not declared. Should it be static?
* dib8000.c:204:15: warning: symbol 'coeff_8k_sb_3seg_1dqpsk' was not declared. Should it be static?
* dib8000.c:209:15: warning: symbol 'coeff_8k_sb_3seg' was not declared. Should it be static?
* dib8000.c:214:15: warning: symbol 'ana_fe_coeff_3seg' was not declared. Should it be static?
* dib8000.c:218:15: warning: symbol 'ana_fe_coeff_1seg' was not declared. Should it be static?
* dib8000.c:222:15: warning: symbol 'ana_fe_coeff_13seg' was not declared. Should it be static?
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If val is a u64, then following:
val *= (u64)1 << 32;
val /= (u64)1 << 32;
should surely be better represented as:
val <<= 32;
val >>= 32;
Especially as, for the division, the compiler might want to actually do a
division:
drivers/built-in.o: In function `lgs8gxx_get_afc_phase':
drivers/media/dvb/frontends/lgs8gxx.c:250: undefined reference to `__udivdi3'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch to support DvbWorld DW2104 device modifications
with STV0903 and DS3000 demods as well as TeVii S660 and Prof 1100
Also replace some magic numbers with meaningfull variables.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support DiSEqC envelope mode. Feature is enabled by setting
config->diseqc_envelope_mode = true (default: disabled).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support 22 kHz tone control for lnbp21 and lnbh24.
(Overrides the 'set_tone' hook of the frontend driver.)
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch updates the SuperH Mobile CEU driver to
not page align the frame size. Useful in the case of
USERPTR with non-page aligned frame sizes and offsets.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cropping is used for data input, and it is not needed now
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct tw9910 output format is Cb - Y - Cr - Y
which is defined in ITU-R BT.656.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tw9910 output is interlaced and its correct order is Bottom - Top
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we have moved most of the functions over to the v4l2-subdev API, only
quering and setting bus parameters are still performed using the legacy
soc-camera client API. Make the use of this API optional for mt9t031.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been experimentally found out, that the sensor only supports up to
512x384 video output and also has some restrictions on minimum scale. We
disable non-working size ranges until, maybe, someone finds out how to properly
set them up. Also add cropping support, an auto white balance control, platform
data to specify master clock frequency and polarity of the IOCTL pin.
create mode 100644 include/media/rj54n1cb0c.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert soc-camera core and all soc-camera drivers to the new mediabus
API. This also takes soc-camera client drivers one step closer to also be
usable with generic v4l2-subdev host drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video subdevices, like cameras, decoders, connect to video bridges over
specialised busses. Data is being transferred over these busses in various
formats, which only loosely correspond to fourcc codes, describing how video
data is stored in RAM. This is not a one-to-one correspondence, therefore we
cannot use fourcc codes to configure subdevice output data formats. This patch
adds codes for several such on-the-bus formats and an API, similar to the
familiar .s_fmt(), .g_fmt(), .try_fmt(), .enum_fmt() API for configuring those
codes. After all users of the old API in struct v4l2_subdev_video_ops are
converted, it will be removed. Also add helper routines to support generic
pass-through mode for the soc-camera framework.
create mode 100644 drivers/media/video/soc_mediabus.c
create mode 100644 include/media/soc_mediabus.h
create mode 100644 include/media/v4l2-mediabus.h
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bits 10-3 of hsync control are the same for Rev0 and Rev1, but only Rev1
also has bits 2-0 for hsync. Account for this difference and also fix a
register name.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power down internal blocks when not streaming.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tri-state all pins when not streaming to save power.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After this change drivers can be further extended to not fail, if they don't
get platform data, but to use defaults.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
