Remove redundant pci_read_irq_line() function for 85xx CDS board.
This function has been realized in common ppc pci code.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the interrupt numbers match the OpenPIC spec intead of the
Freescale docs which distinguish between internal and external interrupts.
Now we can use the interrupt number directly to find the register offset
associated with it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Begin with MPC8548 a new reset control register is added that asserts
HRESET_REQ to board logic.
This register is used for chip reset.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the ppc32 pcibios_alloc_controller take a device node to match
the ppc64 prototypes and have it set arch_data.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have the pci_controller in the exclude function we can easy
figure out if the bus number is the PHB or not. The old style of using a
variable setup at init time was actually broken and would only work in
specific cases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles. They handle producing them by implicitly looking at the
bus, devfn.
The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.
The easiest fix is to just remove all these definitions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add 'mdio' to bus scan id list for platforms with QE UEC
as a consequence of converting UEC mdio driver to an
of_platform driver in the ucc_geth phylib conversion patch.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Renamed the MPC8568 MDS platform code to follow other 85xx boards. There
isn't anything specific about the 8568 MDS code that wouldn't apply to another
85xx MDS system at this point.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleaned up the probing functionality to be more consistent across all 85xx
boards and actually check to see if we should be running on a given board.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8568 MDS reference board
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to suppose platforms with devices above 4Gb on 32 bits platforms
with a >32 bits physical address space, we used to have a special ioremap64
along with a fixup routine fixup_bigphys_addr.
This shouldn't be necessary anymore as struct resource now supports 64 bits
addresses even on 32 bits archs. This patch enables that option when
CONFIG_PHYS_64BIT is set and removes ioremap64 and fixup_bigphys_addr.
This is a preliminary work for the upcoming merge of 32 and 64 bits io.h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove struct pt_regs * from all handlers.
Also remove the regs argument from get_irq() functions.
Compile tested with arch/powerpc/config/* and
arch/ppc/configs/prep_defconfig
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix up some of the buildbreaks from the irq handler changes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Incorporating the new way of cpm2 immr access, introduced in the previous
patch, into CPM2 peripheral devices (fs_enet and cpm_uart). Both ppc and
powerpc approved working( real actions taken in powerpc only, ppc just
has a wrapper to keep init stuff consistent).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
This makes the 8560 evaluation board fully supported under arch/powerpc,
as the first board with CPM2 SoC peripherals. The brand new devicetree
nodes are introduced (intending to be a subset of the QuiccEngine-equipped
models, with dts sources placed into the kernel according to the new convention.
Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART
update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).
This is also verified on mpc8540 and actually make it work (PCI stuff
working as well)
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
* Fix IRQ support in the 85xx CDS boards so it uses the new
generic stuff
* Fix PCI IRQ mapping to use the device tree
* Disabled i8259 support to allow the CDS to boot. This will be
fixed soon, but the current code doesn't even compile, so this
is a vast improvement
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Fixed 8540 ADS support for the new irq layer
* Fixed 8540 ADS support for mapping PCI interrupts
* Updated 8540 ADS to use device tree for interrupt assignment
and sense values
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
mpc* platform changes.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com> and
Andrew Morton.
(tweaked by Andy Isaacson <adi@hexapodia.org>)
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed platform_init usage on 83xx and 85xx and use define_machine and
probe(). For now we always return true in the problem since you can only
build for one specific board at a time. This is an artificial constraint.
When we get ride of it we will need to update the Kconfig's for these
sub-arch's and make the board's probe() functions actually do something.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we build for the MPC8540 ADS produce a uImage by default.
Updated the defconfig to reflect this as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add PCI support for setting PCI from flat device tree on 85xx specifically for
MPC8540 ADS.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ran arch/powerpc/platforms/85xx through Lindent
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename mpc85xx.c to misc.c to match the pattern established by the
8349 port - consistency is a good thing. Also run Lindent on the
file to clean it up.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cut-and-paste from the old platform code in arch/ppc resulted in
arch/powerpc/platforms/85xx/mpc85xx_ads.c having way too many
header files included. Clean this up.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.
This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
