Some types of packet errors are moderately common with longer IB
cables and large clusters, and are not reported with prints by other
IB HCA drivers. This suppresses those messages unless the new
__IPATH_ERRPKTDBG bit is set in ipath_debug. Reporting of temporarily
disabled frequent error interrupts was also made clearer
We also distinguish between chip errors, and bad packets sent or
received in the wording of the messages.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_dbg doesn't need the same prefixes that printk does.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a sticky state. It is useful for diagnosing problems with
boards versus cable/switch problems.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove variables that are set but then never looked at in the ipath
driver. These cleanups came from David Binderman's list of "set but
never used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PCI Express and Hypertransport chip-specific source files should only
be built when the kernel has the capability of actually compiling them.
This fixes the driver build on, for example, ia64.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't attempt to set up the diagpkt device in the module init code.
Instead, wait until a piece of hardware is initialized. Fixes a
problem when loading the ib_ipath module when no InfiniPath hardware
is present: modprobe would go into the D state and stay there.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Prior to this change, the driver was not able to support a HT and PCIE
card simultaneously present in the same machine.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This gives upper-level protocols a chance to unregister while the device
is still usable.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This allows multiple userspace processes to share a single hardware
context in a master/slave arrangement. It is backwards binary compatible
with existing userspace.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the second allocation failed, the first structure allocated in this
routine was not freed.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove some trailing whitespace that has snuck in despite the best
efforts of whitespace=error-all. Also fix a few other whitespace
bogosities.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch only renames files, fixes product names, and updates
comments.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we first submitted a userspace subnet management agent, it was
rejected, so we left it out of the final driver submission. This patch
removes a number of vestigial references to it.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A lot of ipath layer code was only called in one place. Now that the
ipath_core and ib_ipath drivers are merged, it's more sensible to simply
inline the simple stuff that the layer code was doing.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is little point in keeping the two drivers separate, so we are
merging them.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ordering of writethrough store buffers needs to be forced, and we need
to use ifdef to get writethrough behavior to InfiniPath buffers, because
there is no generic way to specify that at this time (similar to code
in char/drm/drm_vm.c and block/z2ram.c).
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a problem where certain error packets are passed
to the InfiniBand layer for processing even though the packet
actually was received with an error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove ips namespace from infinipath drivers. This renames ips_common.h to
ipath_common.h. Definitions, data structures, etc. that were not used by
kernel modules have moved to user-only headers. All names including ips have
been renamed to ipath. Some names have had an ipath prefix added.
Signed-off-by: Christian Bell <christian.bell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't tell for sure if any packets are in the infinipath receive buffer
when we shut down a chip port. Normally this is taken care of by orderly
shutdown, but when processes are terminated, or sending process has a bug, we
can continue to receive packets. So rather than writing zero to the address
registers for the closing port, we point it at a dummy memory.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes some problems uncovered during IB compliance testing to
return the right values for error counters returned by the Performance Get
Counters packet.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The tail register read became redundant as the result of earlier receive
interrupt bug fixes.
Drop another unneeded register read.
And another line that got duplicated.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do an extra check to see if in-memory tail changed while processing packets,
and if so, going back through the loop again (but only once per call to
ipath_kreceive()). In practice, this seems to be enough to guarantee that if
we crossed the clearing of an interrupt at start of ipath_intr with a
scheduled tail register update, that we'll process the "extra" packet that
lost the interrupt because we cleared it just as it was about to arrive.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem was that I was updating the head register multiple times in the
rcvhdrq processing loop, and setting the counter on each update. Since that
meant that the tail register was ahead of head for all but the last update, we
would get extra interrupts. The fix was to not write the counter value except
on the last update.
I also changed to update rcvhdrhead and rcvegrindexhead at most every 16
packets, if there were lots of packets in the queue (and of course, on the
last packet, regardless).
I also made some small cleanups while debugging this.
With these changes, xeon/monty typically sees two openib packets per interrupt
on sdp and ipoib, opteron/monty is about 1.25 pkts/intr.
I'm seeing about 3800 Mbit/s monty/xeon, and 5000-5100 opteron/monty with
netperf sdp. Netpipe doesn't show as good as that, peaking at about 4400 on
opteron/monty sdp. Plain ipoib xeon is about 2100+ netperf, opteron 2900+, at
128KB
Signed-off-by: olson@eng-12.pathscale.com
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also count the number of interrupts where that works (fastrcvint). On any
interrupt where the port0 head and tail registers are not equal, just call the
ipath_kreceive code without reading the interrupt status, thus saving the
approximately 0.25usec processor stall waiting for the read to return. If any
other interrupt bits are set, or head==tail, take the normal path, but that
has been reordered to handle read ahead of pioavail. Also no longer call
ipath_kreceive() from ipath_qcheck(), because that just seems to make things
worse, and isn't really buying us anything, these days.
Also no longer loop in ipath_kreceive(); better to not hold things off too
long (I saw many cases where we would loop 4-8 times, and handle thousands (up
to 3500) in a single call).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Made in-memory rcvhdrq tail update be in dma_alloc'ed memory, not random user
or special kernel (needed for ppc, also "just the right thing to do").
Some cleanups to make unexpected link transitions less likely to produce
complaints about packet errors, and also to not leave SMA packets stuck and
unable to go out.
A few other random debug and comment cleanups.
Always init rcvhdrq head/tail registers to 0, to avoid race conditions (should
have been that way some time ago).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is not a DMA target, so no need to use dma_alloc_coherent on it.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is no longer a /dev/ipath_diag file; instead, there's
/dev/ipath_diag0, 1, etc.
It's still not possible to have diags run on more than one unit at a time,
but that's easy to fix at some point.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix NULL deref due to pcidev being clobbered before dd->ipath_f_cleanup()
was called.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipath driver's table of PCI IDs needs a { 0, } entry at the end.
This makes all of the device aliases visible to userspace so hotplug
loads the module for all supported devices. Without the patch,
modinfo ipath_core only shows:
alias: pci:v00001FC1d0000000Dsv*sd*bc*sc*i*
instead of the correct:
alias: pci:v00001FC1d00000010sv*sd*bc*sc*i*
alias: pci:v00001FC1d0000000Dsv*sd*bc*sc*i*
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Some systems do not set up 64-bit maps on systems with 2GB or less of
memory installed, so we have to fall back to trying a 32-bit setup.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipath driver is a low-level driver for PathScale InfiniPath host
channel adapters (HCAs) based on the HT-400 and PE-800 chips, including
the InfiniPath HT-460, the small form factor InfiniPath HT-460, the
InfiniPath HT-470 and the Linux Networx LS/X.
The ipath_driver.c file contains much of the low-level device handling
code.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
