Drop iop-adma's use of tx_list from struct dma_async_tx_descriptor in
preparation for removal of this field.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
iop33x support is not included because that engine is a bit more awkward
to handle in that it can either be in xor mode or pq mode. The
dmaengine/async_tx layers currently only comprehend static capabilities.
Note iop13xx does not support hardware PQ continuation so the driver
must handle the DMA_PREP_CONTINUE flag for operations across > 16
sources. From the comment for dma_maxpq:
/* When an engine does not support native continuation we need 3 extra
* source slots to reuse P and Q with the following coefficients:
* 1/ {00} * P : remove P from Q', but use it as a source for P'
* 2/ {01} * Q : use Q to continue Q' calculation
* 3/ {00} * Q : subtract Q from P' to cancel (2)
*/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace the flat zero_sum_result with a collection of flags to contain
the P (xor) zero-sum result, and the soon to be utilized Q (raid6 reed
solomon syndrome) zero-sum result. Use the SUM_CHECK_ namespace instead
of DMA_ since these flags will be used on non-dma-zero-sum enabled
platforms.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are two 64 MB outbound memory windows at bus addresses
0x80000000..0x83ffffff and 0x84000000..0x87ffffff for PCI
memory. Currently, on iop32x, only the lower window is available for
allocations, limiting the available space to 64 MB. On iop33x the full
128 MB can be allocated, but the translation value is wrong for the
upper window.
The patch enables the full 128 MB space on iop32x and corrects the
initialization of OMWTVR1. Redundant definitions are deleted. Tested
using a Thecus N2100 board with a graphics adapter in the expansion
slot. Both windows are in use:
00:05.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics
Innovation) Volari Z7 (prog-if 00 [VGA controller])
[...]
Region 0: Memory at 80000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at 84080000 (32-bit, non-prefetchable) [size=256K]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
collie_pm was the only non-PXA user of sharpsl_pm. Now as it's gone we
can merge code into one single file to allow further cleanup.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This is a RealView platform supporting core tiles with ARM11MPCore,
Cortex-A8 or Cortex-A9 (multicore) processors. It has support for MMC,
CompactFlash, PCI-E.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for the DMA blocks in the S3C64XX series of CPUS,
which are based on the ARM PL080 PrimeCell system.
Unfortunately, these DMA controllers diverge from the PL080
design by adding another DMA controller register and
configuration for OneNAND.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The ARM SMP code wasn't properly updated for the cpumask changes, which
results in smp_timer_broadcast() broadcasting ticks to non-online CPUs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.
Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now, as all places that use Scoop GPIO have been converted to use
GPIO API, drop old-style accessors completely.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original arch/arm/include/asm/hardware/vic.h was
written for the PL190 ARM VIC implementation, and as
such does not have any information about the PL192
version.
Add details about the PL192 and PL190 specific registers
and any changes between the two units.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The CLPS7500 platform has not built since 2.6.22-git7 and there
seems to be no interest in fixing it. So, remove the platform
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform independent header files to arch/arm/include/asm, leaving
those in asm/arch* and asm/plat* alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
