This provides a way to defer processing of an interrupt that wakes the
processor out of sleep mode. On 32-bit platforms that use an
interrupt to wake the processor, we have to have interrupts enabled in
hardware at the point where we go to sleep, otherwise the processor
will never wake up. However, because interrupts are logically
disabled at this point, we don't want to process the interrupt
straight away.
This is handled by setting the _TLF_SLEEPING flag. When we get an
interrupt and _TLF_SLEEPING is set, we firstly clear the MSR_EE
(external interrupt enable) bit in the saved MSR value, and secondly
we then return to the address in the link register, like we do for
_TLF_NAPPING, but without actually handling the interrupt.
Note that this is handled somewhat differently on powerbooks, so this
new code will only be used on non-Apple machines.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix following warnings:
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0x9c): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.iowa_register_bus()
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0xa4): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.io_workaround_init()
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With CONFIG_VIRT_CPU_ACCOUNTING disabled, I got the following error:
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c: In function 'spu_switch_log_notify':
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c:2542: error: implicit declaration of function 'get_tb'
make[4]: *** [arch/powerpc/platforms/cell/spufs/file.o] Error 1
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes vmemmap to use a different region (region 0xf) of the
address space, and to configure the page size of that region
dynamically at boot.
The problem with the current approach of always using 16M pages is that
it's not well suited to machines that have small amounts of memory such
as small partitions on pseries, or PS3's.
In fact, on the PS3, failure to allocate the 16M page backing vmmemmap
tends to prevent hotplugging the HV's "additional" memory, thus limiting
the available memory even more, from my experience down to something
like 80M total, which makes it really not very useable.
The logic used by my match to choose the vmemmap page size is:
- If 16M pages are available and there's 1G or more RAM at boot,
use that size.
- Else if 64K pages are available, use that
- Else use 4K pages
I've tested on a POWER6 (16M pages) and on an iSeries POWER3 (4K pages)
and it seems to work fine.
Note that I intend to change the way we organize the kernel regions &
SLBs so the actual region will change from 0xf back to something else at
one point, as I simplify the SLB miss handler, but that will be for a
later patch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If victim (not ctx) is in spu_run, add victim to rq.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Don't return void in pseries/iommu.c
Make mce_data_buf static in pseries/ras.c
Make things static in pseries/rtasd.c
Make things static in pseries/setup.c
vtermno may as well be static in platforms/pseries/lpar.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The declaration for fw_feature_init() is in pseries.h and
implemented in firmware.c, so the latter should include the
former.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make a few things static in lparcfg.c
Make init and exit routines static in rtas_flash.c
Make things static in rtas_pci.c
Make some functions static in rtas.c
Make fops static in rtas-proc.c
Remove unneeded extern for do_gtod in smp.c
Make clocksource_init() static in time.c
Make last_tick_len and ticklen_to_xs static in time.c
Move the declaration of the pvr per-cpu into smp.h
Make kexec_smp_down() and kexec_stack static in machine_kexec_64.c
Don't return void in arch_teardown_msi_irqs() in msi.c
Move declaration of GregorianDay()into asm/time.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a little messier than I'd like because xmon.h only exists
on powerpc and we can't have a static inline and an extern declaration
visible at the same time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
warning: Using plain integer as NULL pointer
warning: Using plain integer as NULL pointer
warning: symbol 'excprint' was not declared. Should it be static?
warning: symbol 'prregs' was not declared. Should it be static?
warning: symbol 'cacheflush' was not declared. Should it be static?
warning: symbol 'read_spr' was not declared. Should it be static?
warning: symbol 'write_spr' was not declared. Should it be static?
warning: symbol 'super_regs' was not declared. Should it be static?
warning: symbol 'mread' was not declared. Should it be static?
warning: symbol 'mwrite' was not declared. Should it be static?
warning: symbol 'byterev' was not declared. Should it be static?
warning: symbol 'memex' was not declared. Should it be static?
warning: symbol 'bsesc' was not declared. Should it be static?
warning: symbol 'dump' was not declared. Should it be static?
warning: symbol 'prdump' was not declared. Should it be static?
warning: symbol 'generic_inst_dump' was not declared. Should it be static?
warning: symbol 'ppc_inst_dump' was not declared. Should it be static?
warning: symbol 'memops' was not declared. Should it be static?
warning: symbol 'memdiffs' was not declared. Should it be static?
warning: symbol 'memlocate' was not declared. Should it be static?
warning: symbol 'memzcan' was not declared. Should it be static?
warning: symbol 'proccall' was not declared. Should it be static?
warning: symbol 'scannl' was not declared. Should it be static?
warning: symbol 'hexdigit' was not declared. Should it be static?
warning: symbol 'flush_input' was not declared. Should it be static?
warning: symbol 'inchar' was not declared. Should it be static?
warning: symbol 'take_input' was not declared. Should it be static?
warning: symbol 'xmon_init' was not declared. Should it be static?
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The typdef for irqreturn_t was moved into its own header a
while back, so there's no reason we can't move xmon_irq()
into xmon.h now.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some of the routines defined in mpic_msi.c are declared mpic.h,
so the former should include the latter.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somewhere along the way (e28f7faf05,
"Four level pagetables for ppc64") we ended up with duplicate
definitions for pte_freelist_cur and pte_freelist_force_free.
Somehow this compiles, but it would be better to just have one
definition for each.
The two definitions we end up with can be static too!
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
... instead of having extern declarations in a .c file.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make two vmemmap helpers static in init_64.c
Make stab variables static in stab.c
Make psize defs static in hash_utils_64.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
... instead of having an extern declaration in a .c file.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For each mv64360 entry in the OpenFirmware database, add the
registration of an of_bus to take care of devices connected to
the MV64x60 asynchronous devices controller.
This change makes it possible for those devices to be detected by
drivers that support the of_platform without having a custom call
for each of them in the board file.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We use the low bits of regs->trap as flag bits. We already indicate
critical and machine check level exceptions via this mechanism. Extend it
to indicate debug level exceptions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace TIF_RESTORE_SIGMASK with TLF_RESTORE_SIGMASK and define
our own set_restore_sigmask() function. This saves the costly
SMP-safe set_bit operation, which we do not need for the sigmask
flag since TIF_SIGPENDING always has to be set too.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
bitmap_find_free_region(), called by mpic_msi_alloc_hwirqs() may return
signed, but hwirq is unsigned. A failed allocation remains unnoticed.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
bitmap_find_free_region(), called by mpic_msi_alloc_hwirqs() may return
signed, but hwirq is unsigned. A failed allocation remains unnoticed.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Cc: "Nelson, Shannon" <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DIU platform code should not just write to the PIXIS' BRDCFG0 register,
it should set and clear its own bits only, otherwise it will break
firmware setup (in fact it breaks second uart).
Also get rid of magic numbers in the related code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8568 MDS needs some configuration changes to the PHY in order to
work properly. These are done in the firmware, normally, but Linux
shouldn't need to rely on the firmware running such things (someone
could disable the PHY support in the firmware to save space, for instance).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As of current mainline tree, TULIP driver is unusable on MPC8610HPCD
boards. There is a patch[1] floating around (and also included in the
BSP), which tries to heal the situation, though the ethernet is still
unusable. Practically it takes ages to mount NFS filesystem:
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 180k init
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 OK
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 OK
nfs: server 10.0.0.2 not responding, still trying
So, instead of trying to add uli526x functionality into TULIP driver
(which is already bloated enough), I fixed existing ULI526X driver
and now it works perfectly well here.
[1] http://www.bitshrine.org/gpp/0024-MPC8610-ETH-Lyra-native-ethernet.txt
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes a few more miscellaneous compile problems with ARCH=ppc.
1. Don't compile devres.c on ARCH=ppc, it doesn't have ioremap_flags.
2. Include <asm/irq.h> in setup.c for the __DO_IRQ_CANON definition.
3. Include <linux/proc_fs.h> in residual.c for the
definition of create_proc_read_entry.
4. Fix xchg_ptr to be a static inline to eliminate a compiler warning.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 76bc080ef5 ("POWERPC] Make default
cputable entries reflect selected CPU family") added default entries
for the e200 and e500 families, but missed a closing brace on those
entries, as pointed out by David Gibson. This adds the closing braces.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
[POWERPC] Remove leftover printk in isa-bridge.c
[POWERPC] Remove duplicate #include
[POWERPC] Initialize lockdep earlier
[POWERPC] Document when printk is useable
[POWERPC] Fix bogus paca->_current initialization
[POWERPC] Fix of_i2c include for module compilation
[POWERPC] Make default cputable entries reflect selected CPU family
[POWERPC] spufs: lockdep annotations for spufs_dir_close
[POWERPC] spufs: don't requeue victim contex in find_victim if it's not in spu_run
[POWERPC] 4xx: Fix PCI mem in sequoia DTS
[POWERPC] 4xx: Add endpoint support to 4xx PCIe driver
[POWERPC] 4xx: Fix problem with new TLB storage attibute fields on 440x6 core
[POWERPC] spufs: spu_create should send inotify IM_CREATE event
[POWERPC] spufs: handle faults while the context switch pending flag is set
[POWERPC] spufs: fix concurrent delivery of class 0 & 1 exceptions
[POWERPC] spufs: try to route SPU interrupts to local node
[POWERPC] spufs: set SPU_CONTEXT_SWITCH_PENDING before synchronising SPU irqs
[POWERPC] spufs: don't acquire state_mutex interruptible while performing callback
[POWERPC] spufs: update master runcntl with context lock held
[POWERPC] spufs: fix post-stopped update of MFC_CNTL register
...
This printk() appears twice in the same function. Only the latter one
in the inval_range: section appears to be legitimate.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove duplicate #include of <asm/prom.h> in
arch/powerpc/kernel/btext.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves lockdep_init() to before udbg_early_init() as the later
can call things that acquire spinlocks etc... This also makes printk
safer to use earlier.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When debugging early boot problems, it's common to sprinkle printk's
all over the place. However, on 64-bit powerpc, this can lead to
memory corruption if done too early due to the PACA pointer and
lockdep core not being initialized.
This adds some comments to early_setup() that document when it is
safe to do so in order to save time for whoever has to debug that
stuff next.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When doing lockdep, I had two patches to initialize paca->_current
early, one bogus, and one correct. Unfortunately both got merged
as the bad one ended up being part of the main lockdep patch by
mistake. This causes memory corruption at boot. This removes
the offending code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changes the cputable so that various CPU families that have an exclusive
CONFIG_ option have a more sensible default entry to use if the specific
processor hasn't been identified.
This makes the kernel more generally useful when booted on an unknown
PVR for things like new 4xx variants.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
net: Added ASSERT_RTNL() to dev_open() and dev_close().
can: Fix can_send() handling on dev_queue_xmit() failures
netns: Fix arbitrary net_device-s corruptions on net_ns stop.
netfilter: Kconfig: default DCCP/SCTP conntrack support to the protocol config values
netfilter: nf_conntrack_sip: restrict RTP expect flushing on error to last request
macvlan: Fix memleak on device removal/crash on module removal
net/ipv4: correct RFC 1122 section reference in comment
tcp FRTO: SACK variant is errorneously used with NewReno
e1000e: don't return half-read eeprom on error
ucc_geth: Don't use RX clock as TX clock.
cxgb3: Use CAP_SYS_RAWIO for firmware
pcnet32: delete non NAPI code from driver.
fs_enet: Fix a memory leak in fs_enet_mdio_probe
[netdrvr] eexpress: IPv6 fails - multicast problems
3c59x: use netstats in net_device structure
3c980-TX needs EXTRA_PREAMBLE
fix warning in drivers/net/appletalk/cops.c
e1000e: Add support for BM PHYs on ICH9
uli526x: fix endianness issues in the setup frame
uli526x: initialize the hardware prior to requesting interrupts
...
We need to acquire the parent i_mutex with I_MUTEX_PARENT to keep
lockdep happy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We should not requeue the victim context in find_victim if the owner is
not in spu_run. It's first not needed because leaving the context on
the spu is an optimization and second is harmful because it means the
owner could re-enter spu_run when the context is on the runqueue and
trip the BUG_ON in __spu_update_sched_info.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This patch is fixes the sequoia.dts device tree file to use the values defined
in the 440Epx data sheet from AMCC.
That fixes an issue where some devices, including graphics cards, would not
initialize properly because the PCI resource space was not big enough.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds basic endpoint support to the 4xx PCIe driver.
This is done by checking the device_type property of the PCIe
device node ("pci" for root-complex and "pci-endpoint" for endpoint
configuration).
Note: Currently we map a fixed 64MByte window to PLB address 0 (SDRAM).
This should probably be configurable via a dts property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The new 440x6 core used on AMCC 460EX/GT introduces new storage attibure
fields to the TLB2 word. Those are:
Bit 11 12 13 14 15
WL1 IL1I IL1D IL2I IL2D
With these bits the cache (L1 and L2) can be configured in a more flexible
way, instruction- and data-cache independently now. The "old" I and W bits
are still available and setting these old bits will automically set these
new bits too (for backward compatibilty).
The current code does not clear these fields resulting in disabling the cache
by chance. This patch now makes sure that these new bits are cleared when
the TLB2 word is written.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Creating a spufs context or gand using spu_create should send an inotify
event so that things like performance monitors have an easy way to find
out about newly created contexts.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Simply replace proc_create and further data assigned with proc_create_data.
No need to check for data!=NULL after that.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We provide an ioremap_flags, so this provides a corresponding
devm_ioremap_prot. The slight name difference is at Ben
Herrenschmidt's request as he plans on changing ioremap_flags to
ioremap_prot in the future.
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, page fault handlers don't issue a mfc restart if the context
switch pending flag is set, which can leave us with a hanging DMA after
a context restore.
This patch introduces fault pending flag that is set by the fault
handler and read by the context switch code, so that the latter can add
the restart bit at the right spot, after it has successfuly saved the
state of the mfc control register.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
SPU class 0 & 1 exceptions may occur in parallel, so we may end up
overwriting csa.dsisr.
This change adds dedicated fields for each class to the spu and the spu
context so that fault data is not overwritten.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we re-route SPU interrupts to the current cpu, which may be
on a remote node. In the case of time slicing, all spu interrupts will
end up routed to the same cpu, where the spusched_tick occurs.
This change routes mfc interrupts to the cpu where the controlling
thread last ran, provided that cpu is on the same node as the spu
(otherwise don't reroute interrupts).
This should improve performance and provide a more predictable
environment for processing spu exceptions. In the past we have seen
concurrent delivery of spu exceptions to two cpus. This eliminates that
concern.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
synchronize_irq() provides the serialization for
SPU_CONTEXT_SWITCH_PENDING which is read with a simple load. This
routine guarantees that the relevant interrupt handlers are not running,
so that the next time they do run they will see the update
memory value.
This must be done correctly so that exception handling code does not
restart the mfc in the middle of a context switch while we are trying
to atomically stop it and save state.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There's currently no way to tell if spu_process_callback has
returned with the state mutex held, as -EINTR may be returned
by either the syscall or the spu_acquire fail case.
Instead, just do a non-interruptible mutex_lock here.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we update the SPU master run control bit (ie,
spu_enable_spu) in spufs_run_spu before we grab the context mutex. This
can result in races with other processes accessing this context's
resources.
This change moves the spu_enable_spu to after we have acquired the
context lock.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We currently have two issues with the MFC save code:
* save_mfc_decr doesn't handle a transition of 1 -> 0 of the Ds bit
* The Q bit may be stale in the CSA
This change fixes the first issue by clearing the relevant bits from
the MFC_CNTL value in the CSA before or-ing in the updated status.
Also, we add the Q bit to the updated status.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we can introduce invalid entries into the MFC queues:
1) context starts a DMA
2) context gets scheduled out during a DMA
- kernel saves MFC queue to CSA
- kernel saves 0x0 in csa->mfc_control_RW
3) context gets scheduled in
- csa->mfc_control[Q] ('queues empty') isn't set, so DMA queues are
restored from the CSA
4) context's DMA is completed
5) context gets scheduled out again, no DMA occuring this time
- kernel sees that MFC_CNTL[Q] ('queues empty') is set, so doesn't
touch saved queue data in CSA
- kernel saves 0x0 in csa->mfc_control_RW
6) context gets scheduled in
- csa->mfc_control[Q] ('queues empty') isn't set (we saved is as 0!),
so DMA queues are restored from the CSA
In this last restore, we've restored the queue status from step 2,
which are now invalid.
This change makes save_mfc_cntl() closer to the save/restore sequence,
as specified in the CBE handbook.
With changes from Luke Browning.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
When we issue a MFC purge request, we may inadvertantly clear the
suspended status.
This change adds the MFC_CNTL_SUSPEND_MASK when we issue a purge
request, so that the suspend bit is masked out.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We may currently lose interrupts during SPE context switch, as we alter
the INT_Route register. Because the IIC uses a per-thread priority
status, changing the interrupt routing to a different thread means that
the IRQ is no longer masked by the priority status, so we end up with
two fasteoi IRQ handlers executing for the one irq_desc. The fasteoi
handler doesn't handle multiple IRQs, so drops the second one.
Fix this by using our own flow handler. This is based on
handle_edge_irq, but issues an eoi after IRQs are handled, and doesn't
do any mask/unmasking.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This patch adds the delivery of INTERRUPT_FP_UNAVAIL exceptions to the guest.
It's needed if a guest uses ppc binaries using the Floating point instructions.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This reduces host CPU usage when the guest is idle. However, the guest must
set MSR[WE] in its idle loop, which Linux did not do until 2.6.26.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
This fixes a regression reported by Kamalesh Bulabel where a POWER4
machine would crash because of an SLB miss at a point where the SLB
miss exception was unrecoverable. This regression is tracked at:
http://bugzilla.kernel.org/show_bug.cgi?id=10082
SLB misses at such points shouldn't happen because the kernel stack is
the only memory accessed other than things in the first segment of the
linear mapping (which is mapped at all times by entry 0 of the SLB).
The context switch code ensures that SLB entry 2 covers the kernel
stack, if it is not already covered by entry 0. None of entries 0
to 2 are ever replaced by the SLB miss handler.
Where this went wrong is that the context switch code assumes it
doesn't have to write to SLB entry 2 if the new kernel stack is in the
same segment as the old kernel stack, since entry 2 should already be
correct. However, when we start up a secondary cpu, it calls
slb_initialize, which doesn't set up entry 2. This is correct for
the boot cpu, where we will be using a stack in the kernel BSS at this
point (i.e. init_thread_union), but not necessarily for secondary
cpus, whose initial stack can be allocated anywhere. This doesn't
cause any immediate problem since the SLB miss handler will just
create an SLB entry somewhere else to cover the initial stack.
In fact it's possible for the cpu to go quite a long time without SLB
entry 2 being valid. Eventually, though, the entry created by the SLB
miss handler will get overwritten by some other entry, and if the next
access to the stack is at an unrecoverable point, we get the crash.
This fixes the problem by making slb_initialize create a suitable
entry for the kernel stack, if we are on a secondary cpu and the stack
isn't covered by SLB entry 0. This requires initializing the
get_paca()->kstack field earlier, so I do that in smp_create_idle
where the current field is initialized. This also abstracts a bit of
the computation that mk_esid_data in slb.c does so that it can be used
in slb_initialize.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The routines ps3_virq_setup() and ps3_virq_destroy() are used
in only one file, so make them static.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Arrange for a syntax check to always be done on the powerpc/mm/slb.c
DBG() macro by defining it to pr_debug() for non-debug builds.
Also, fix these related compile warnings:
slb.c:273: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'long unsigned int
slb.c:274: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/xilinx_intc.c: In function 'xilinx_intc_init':
arch/powerpc/sysdev/xilinx_intc.c:111: warning: format '%08X' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/char/xilinx_hwicap/xilinx_hwicap.c: In function 'hwicap_setup':
drivers/char/xilinx_hwicap/xilinx_hwicap.c:626: warning: cast to pointer from integer of different size
drivers/char/xilinx_hwicap/xilinx_hwicap.c:646: warning: format '%x' expects type 'unsigned int', but argument 6 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When resource_size_t is larger than an int, the current code
generates a build warning. Kill it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix current (-git16) missing docbook/kernel-doc notation in RapidIO files.
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'sys_size'
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'phy_type'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:188): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:224): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:245): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:270): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:311): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:996): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie node which is resposible for PCI-E x8 slot
functioning. Though, this was tested using only x1 SKY2 NIC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As TICK_LENGTH_SHIFT is used for more than just the tick length, the name
isn't quite approriate anymore, so this renames it to NTP_SCALE_SHIFT.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes time_freq to a 64bit value and makes it static (the only outside
user had no real need to modify it). Intermediate values were already 64bit,
so the change isn't that big, but it saves a little in shifts by replacing
SHIFT_NSEC with TICK_LENGTH_SHIFT. PPM_SCALE is then used to convert between
user space and kernel space representation.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a minimalistic braille screen reader support. This is meant to
be used by blind people e.g. on boot failures or when / cannot be mounted
etc and thus the userland screen readers can not work.
[akpm@linux-foundation.org: fix exports]
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jiri Kosina <jikos@jikos.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit edd8ce6743 (Use extended crashkernel
command line on ppc64), changed the logic in reserve_crashkernel()
which deals with the crashkernel= command line option.
This introduced a bug in the case when there is no crashkernel= option,
or it is incorrect. We would fall through and calculate the crash_size
based on the existing values in crashk_res. If both start and end are 0,
the default, we calculate the crash_size as 1 byte - which is wrong.
Rework the logic so that we use crashk_res, regardless of whether it's
set by the command line or via the device tree (see prom.c). Then check
if we have an empty range (end == start), and if so make sure to set
both end and start to zero (this is checked in machine_kexec_64.c). Then
we calculate the crash_size once we know we have a non-zero range.
Finally we always want to warn the user if they specify a base != 32MB,
so remove the special case for that in the command line parsing case.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current_thread_info() macro, used by preempt_count(), assumes the
base address and size of the stack are THREAD_SIZE aligned.
The emergency stack currently isn't either of these things, which
could potentially cause problems anytime we're running on the
emergency stack. That includes when we detect a bad kernel stack
pointer, and also during early_setup_secondary().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sputrace module contained a trace entry for spu_acquire_saved, but
this marker was not placed anywhere. Fix this by adding a marker to the
routine.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Fix a typo in the marker for the find_victim function, which prevented
it from being traced. It previously read find_vitim.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The sputrace module contained a reference to a marker for
destroy_spu_context, but this marker did not appear in the code. Fix
this by adding a marker in the function.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The markers facility defines the marker parameters to be of the form
'name %format'. Add parameter names to sputrace, to specify the context
and %spu paramerters, instead of just specifying the '%format' part.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There are userspace instrumentation tools that need to monitor spu
context switches. This patch adds a new file called 'switch_log' to
each spufs context directory that can be used to monitor the context
switches.
Context switch in/out and exit from spu_run are monitored after the
file was first opened and can be read from it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[RAPIDIO] Change RapidIO doorbell source and target ID field to 16-bit
[RAPIDIO] Add RapidIO connection info print out and re-training for broken connections
[RAPIDIO] Add serial RapidIO controller support, which includes MPC8548, MPC8641
[RAPIDIO] Add RapidIO node probing into MPC86xx_HPCN board id table
[RAPIDIO] Add RapidIO node into MPC8641HPCN dts file
[RAPIDIO] Auto-probe the RapidIO system size
[RAPIDIO] Add OF-tree support to RapidIO controller driver
[RAPIDIO] Add RapidIO multi mport support
[RAPIDIO] Move include/asm-ppc/rio.h to asm-powerpc
[RAPIDIO] Add RapidIO option to kernel configuration
[RAPIDIO] Change RIO function mpc85xx_ to fsl_
[POWERPC] Provide walk_memory_resource() for powerpc
[POWERPC] Update lmb data structures for hotplug memory add/remove
[POWERPC] Hotplug memory remove notifications for powerpc
[POWERPC] windfarm: Add PowerMac 12,1 support
[POWERPC] Fix building of pmac32 when CONFIG_NVRAM=m
[POWERPC] Add IRQSTACKS support on ppc32
[POWERPC] Use __always_inline for xchg* and cmpxchg*
[POWERPC] Add fast little-endian switch system call
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Add correct ->owner to proc_fops to fix reading/module unloading race.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Board-specific defconfigs based on current mpc5200_defconfig, archival
lite5200_defconfig, and [cm5200|motionpro|tqm5200]_defconfig from the
linux-2.6-denx tree. Kernels build using these defconfigs were verified
to boot with root filesystem mounted over NFS on Motion-PRO, TQM5200
and Lite5200B boards. CM5200 target was not tested due to hardware
unavailability.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds gpiolib support for mpc5200 SOCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a set_type function for external (GPIO) interrupts.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Change RapidIO doorbell source and target ID field to 16-bit for
support large system size, which max rio devid is 65535.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This initializes the RapidIO controller driver using addresses and
interrupt numbers obtained from the firmware device tree, rather than
using hardcoded constants.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The original RapidIO driver suppose there is only one mpc85xx RIO controller
in system. So, some data structures are defined as mpc85xx_rio global, such
as 'regs_win', 'dbell_ring', 'msg_tx_ring'. Now, I changed them to mport's
private members. And you can define multi RIO OF-nodes in dts file for multi
RapidIO controller in one processor, such as PCI/PCI-Ex host controllers in
Freescale's silicon. And the mport operation function declaration should be
changed to know which RapidIO controller is target.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The driver is suitable for the Freescale MPC8641 processor as well as
85xx processors, so this changes the mpc85xx prefix to fsl.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide walk_memory_resource() for 64-bit powerpc. PowerPC maintains
logical memory region mapping in the lmb.memory structure. Walk
through these structures and do the callbacks for the contiguous
chunks.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc kernel maintains information about logical memory blocks
in the lmb.memory structure, which is initialized and updated at boot
time, but not when memory is added or removed while the kernel is
running.
This adds a hotplug memory notifier which updates lmb.memory when
memory is added or removed. This information is useful for eHEA
driver to find out the memory layout and holes.
NOTE: No special locking is needed for lmb_add() and lmb_remove().
Calls to these are serialized by caller. (pSeries_reconfig_chain).
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hotplug memory remove notifier for 64-bit powerpc. This gets invoked
by writing to /proc/ppc64/ofdt the string "remove_node " followed by
the firmware device tree pathname of the node that needs to be removed.
In response, this adjusts the sections and removes sysfs entries by
calling __remove_pages(). Then it calls arch-specific code to get rid
of the hardware MMU mappings for the section of memory.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Reviewed-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a new driver named windfarm_pm121, which drives the
fans on PowerMac 12,1 machines : iMac G5 iSight (rev C) 17" and
20". It's based on the windfarm_pm81 driver from Benjamin
Herrenschmidt.
This includes fixes from David Woodhouse correcting the names of some
of the sensors.
Signed-off-by: Étienne Bersac <bersace@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kamalesh Babulal (kamalesh@linux.vnet.ibm.com) reports that CONFIG_NVRAM=m
is valid in terms of Kconfig but fails to build with:
Building modules, stage 2.
MODPOST 1401 modules
ERROR: "pmac_newworld" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
ERROR: "__alloc_bootmem" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
make[1]: *** [__modpost] Error
The arch/powerpc/platforms/powermac/nvram.c code really needs to be
builtin, but as its compilation is dependent on a generic Kconfig
symbol we force nvram.c to be builtin if CONFIG_NVRAM is 'y' or 'm'.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes it possible to use separate stacks for hard and soft IRQs
on 32-bit powerpc as well as on 64-bit. The code for 32-bit is just
the 32-bit analog of the 64-bit code.
* Added allocation and initialization of the irq stacks. We limit the
stacks to be in lowmem for ppc32.
* Implemented ppc32 versions of call_do_softirq() and call_handle_irq()
to switch the stack pointers
* Reworked how we do stack overflow detection. We now keep around the
limit of the stack in the thread_struct and compare against the limit
to see if we've overflowed. We can now use this on ppc64 if desired.
[ paulus@samba.org: Fixed bug on 6xx where we need to reload r9 with the
thread_info pointer. ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a system call on 64-bit platforms for switching between
little-endian and big-endian modes that is much faster than doing a
prctl call. This system call is handled as a special case right at
the start of the system call entry code, and because it is a special
case, it uses a system call number which is out of the range of
normal system calls, namely 0x1ebe.
Measurements with lmbench on a 4.2GHz POWER6 showed no measurable
change in the speed of normal system calls with this patch.
Switching endianness with this new system call takes around 60ns on a
4.2GHz POWER6, compared with around 300ns to switch endian mode with a
prctl. This can provide a significant performance advantage for
emulators for little-endian architectures that want to switch between
big-endian and little-endian mode frequently, e.g. because they are
generating instructions sequences on the fly and they want to run
those sequences in little-endian mode.
The other thing about this system call is that it doesn't clobber as
many registers as a normal system call. It only clobbers r12.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move mv643xx_eth's static state (ethernet register block base address
and MII management interface spinlock) into a struct hanging off the
shared platform device. This is necessary to support chips that
contain multiple mv643xx_eth silicon blocks.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Add platform code to support Freescale DIU. The platform code includes
framebuffer memory allocation, pixel format, monitor port, etc.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs
All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0. Changing pixel clock has no effect
on other fbs.
Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0
required command line parameters to preallocate memory for frame buffer diufb.
optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:
Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60
Bpp
bpp=32, bpp=24, or bpp=16
Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS
Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.
If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alter the block device ->direct_access() API to work with the new
get_xip_mem() API (that requires both kaddr and pfn are returned).
Some architectures will not do the right thing in their virt_to_page() for use
by XIP (to translate from the kernel virtual address returned by
direct_access(), to a user mappable pfn in XIP's page fault handler.
However, we can't switch it to just return the pfn and not the kaddr, because
we have no good way to get a kva from a pfn, and XIP requires the kva for its
read(2) and write(2) handlers. So we have to return both.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-mm@kvack.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures use an effectively identical definition of online_page(), so
just make it common code. x86-64, ia64, powerpc and sh are actually
identical; x86-32 is slightly different.
x86-32's differences arise because it puts its hotplug pages in the highmem
zone. We can handle this in the generic code by inspecting the page to see if
its in highmem, and update the totalhigh_pages count appropriately. This
leaves init_32.c:free_new_highpage with a single caller, so I folded it into
add_one_highpage_init.
I also removed an incorrect comment referring to the NUMA case; any NUMA
details have already been dealt with by the time online_page() is called.
[akpm@linux-foundation.org: fix indenting]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamez.hiroyu@jp.fujitsu.com>
Tested-by: KAMEZAWA Hiroyuki <kamez.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Christoph Lameter <clameter@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This functionality is definitely experimental, but is capable of running
unmodified PowerPC 440 Linux kernels as guests on a PowerPC 440 host. (Only
tested with 440EP "Bamboo" guests so far, but with appropriate userspace
support other SoC/board combinations should work.)
See Documentation/powerpc/kvm_440.txt for technical details.
[stephen: build fix]
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
virtex405-head.S is an assembler file, not a C file; therefore BOOTAFLAGS
is the correct place to set the needed -mcpu=405 flag.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The AMCC 460GT doesn't have an FPU so let's not enable support for it.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds default NOR entries to the AMCC Canyonlands (460EX)
and Glacier (460GT) dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based adressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the ns16550 driver to use the reg-offset property
so that the Xilinx UART 16550 can be used with it. The reg-shift
was already being handled.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds support for PCI Express port on Celleb. I/O space of this
PCI Express port is not mapped in memory space. So we use the
io-workaround mechanism to make accesses indirect.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves miscellaneous files for Beat into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves SPU support code on Beat into platforms/cell/.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves files for mmu and iommu on Beat into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves files for Beat hvcall interfaces into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the SCC (Super Companion Chip) related code for celleb
into platforms/cell/.
All files in this patch are used by celleb-beat and celleb-native
commonly.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the base code for celleb support into platforms/cell/.
All files in this patch are used by celleb-beat and celleb-native
commonly.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now, we can use generic io-workarounds mechanism and the workaround
code for spider-pci. This changes Celleb PCI code to use spider-pci
code.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits cell io-workaround code into spider-pci dependent code and
a generic part, and also moves io-workarounds initialization into
cell_setup_phb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a DEBUG config setting which turns on all (most) of the debugging
under platforms/pseries.
To have this take effect we need to remove all the #undef DEBUG's, in
various files. We leave the #undef DEBUG in platforms/pseries/lpar.c,
as this enables debugging printks from the low-level hash table routines,
and tends to make your system unusable. If you want those enabled you
still have to turn them on by hand.
Also some of the RAS code has a DEBUG block which causes a functional
change, so I've keyed this off a different (non-existant) debug #define.
This is only enabled if you have PPC_EARLY_DEBUG enabled also.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In pseries/lpar.c, fix some printf specifier mismatches, and add
a newline to one printk.
In pseries/rtasd.c add "rtasd" to some messages to make it clear
where they're coming from.
In pseries/scanlog.c remove the hand-rolled runtime debugging support
in there. This file has been largely unchanged for eons, if we need to
debug it in future we can recompile.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On pseries LPAR we can call the udbg routines, and the udbg console very
early. So mark the udbg console as safe to call early in boot, and register
the udbg console as soon as the udbg routines are hooked up.
This allows platforms/pseries code to use printk() and pr_debug() rather
than needing to call udbg_printf() directly for early debugging. This is
nice because a) it's standard, b) it goes via the printk buffer, and c)
you can get printk time stamps.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The udbg console should be safe to call basically at any time after boot.
It does not need any per-cpu resources or for the cpu to be online, as
long as there is a udbg_putc routine hooked up it should work. So mark it
as CON_ANYTIME.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because the udbg_console has CON_ENABLED set, it's possible that when we
register it with the console code the index won't be set. This leads to
slightly confusing boot messages like:
[ 0.000000] console [udbg-1] enabled
We could remove CON_ENABLED, but we don't want to do that, we always
want the udbg console to be activated, even if the user specified some
other console on the command line.
The simplest fix seems to be just to set the index to 0 by hand. There
is no issue with duplicate udbg consoles, as we guard against registering
multiple times in register_early_udbg_console().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the required functionality to fill in all pacas at runtime.
With NR_CPUS=1024
text data bss dec hex filename
137 1704032 0 1704169 1a00e9 arch/powerpc/kernel/paca.o :Before
121 1179744 524288 1704153 1a00d9 arch/powerpc/kernel/paca.o :After
Also remove unneeded #includes from arch/powerpc/kernel/paca.c
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently all iSeries secondary CPUs spin directly on the cpu_start
field in their paca. Make them spin on the global
__secondary_hold_spinloop until after the pacas have been initialised.
As Stephen Rothwell points out, this works at the moment because
__secondary_hold_spinloop is being set already, but iSeries isn't
looking at it :)
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Removed get_msr(), get_srr0(), and get_srr1() - not used anywhere
* Use STACK_FRAME_OVERHEAD instead of magic number
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace two open-coded occurences of the of_get_next_parent() logic.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As BenH said the other day, it is an "accident" that prom_init.o is
linked with the rest of the kernel. The truth is a little more
subtle, prom_init isn't truly bootloader, it does access kernel data
in a few places.
What we can do is discourage people from adding new code that accesses
data outside of prom_init. And hence this patch; from the script:
# This script checks prom_init.o to see what external symbols it
# is using, if it finds symbols not in the whitelist it returns
# an error. The point of this is to discourage people from
# intentionally or accidentally adding new code to prom_init.c
# which has side effects on other parts of the kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Removed TI_EXECDOMAIN define as its not used anywhere
* Use STACK_INT_FRAME_SIZE to allow common define of INT_FRAME_SIZE
* Define TI_CPU on both ppc32 & ppc64 (removes an ifdef).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use (31-THREAD_SHIFT) to get to thread_info from stack pointer. This makes
the code a bit easier to read and more robust if we ever change THREAD_SHIFT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the inclusion of asm-offsets.h from stacktrace.c. It isn't
supposed to be included in C code and it causes problems with multiple
definitions of things.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fixmap code from x86 allows us to have compile time virtual addresses
that we change the physical addresses of at run time.
This is useful for applications like kmap_atomic, PCI config that is done
via direct memory map, kexec/kdump.
We got ride of CONFIG_HIGHMEM_START as we can now determine a more optimal
location for PKMAP_BASE based on where the fixmap addresses start and
working back from there.
Additionally, the kmap code in asm-powerpc/highmem.h always had debug
enabled. Moved to using CONFIG_DEBUG_HIGHMEM to determine if we should
have the extra debug checking.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added support to allow an 85xx kernel to be run from a non-zero physical
address (useful for cooperative asymmetric multiprocessing situations and
kdump). The support can be configured at compile time by setting
CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as
desired.
Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this
config option causes the kernel to determine at runtime the physical
addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If
CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning.
However, CONFIG_PHYSICAL_START will always be used to set the LOAD program
header physical address field in the resulting ELF image.
Currently we are limited to running at a physical address that is a
multiple of 256M. This is due to how we map TLBs to cover
lowmem. This should be fixed to allow 64M or maybe even 16M alignment
in the future. It is considered an error to try and run a kernel at a
non-aligned physical address.
All the magic for this support is accomplished by proper initialization
of the kernel memory subsystem and use of ARCH_PFN_OFFSET.
The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings.
ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET.
/dev/mem continues to allow access to any physical address in the system
regardless of how CONFIG_PHYSICAL_START is set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MPSC driver and prpmc2800.dts have been modified to use property
'cell-index' as the serial port number, but the early serial console
driver for the mv64x60 has not been modified to use this new property.
This fixes it.
Signed-off-by: Remi Machet (rmachet@slac.stanford.edu)
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If one of the devices of the mv64x60 init fails, the remaining
devices are not initialized.
This changes the code to display an error and continue the
initialization.
Signed-off-by: Remi Machet (rmachet@slac.stanford.edu)
Signed-off-by: Paul Mackerras <paulus@samba.org>
I2C parameters freq_m and freq_n are assigned defaults in the code,
but if properties for those parameters are not found in the open
firmware description the init routine returns an error and doesn't
create the platform device.
This changes the code so that it doesn't return an error if the
properties are not found but instead uses the default values.
Signed-off-by: Remi Machet (rmachet@slac.stanford.edu)
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc kernel stacks need to be naturally aligned, as they
contain the thread info at the bottom, which is obtained by
clearing the low bits of the stack pointer.
However, when using 64K pages, the stack is smaller than a page,
so we use kmalloc to allocate it, but that doesn't provide the
alignment guarantee we need.
It appeared to work so far... until one enables SLUB debugging
which then returns unaligned pointers. Ooops...
This fixes it by using a slab cache with enforced alignment. It
relies on my previous patch that adds a thread_info_cache_init()
callback.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
os-area.c requires routines declared in linux/of.h, so should include it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
numa.c requires routines declared in linux/of.h, so should include it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit e4cc58944c, as
requested by Roland McGrath, because compat_ptrace_request (added in
commit e16b278164, "ptrace:
compat_ptrace_request siginfo") now handles this case.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
603 CPUs have the same issue that some 750 CPUs have in that they can crash
in funny ways if a store from an FPU register instruction is executed on a
register that has never been initialized since power on. This patch fixes
it by making sure all FP registers have been properly initialized at kernel
boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the generic pci_enable_resources() instead of the arch-specific code.
The generic version is functionally equivalent, but uses dev_printk.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists. The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Define the copy_siginfo_from_user32 entry point for powerpc, so
that generic CONFIG_COMPAT code can call it. We already had the
code rolled into compat_sys_rt_sigqueueinfo, this just moves it
out into the canonical function that other arch's define.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current versions of gdb require a working implementation of
PTRACE_GETSIGINFO for proper watchpoint support. Since struct siginfo
contains pointers it must be converted when passed to a 32-bit debugger.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.26: (1090 commits)
[NET]: Fix and allocate less memory for ->priv'less netdevices
[IPV6]: Fix dangling references on error in fib6_add().
[NETLABEL]: Fix NULL deref in netlbl_unlabel_staticlist_gen() if ifindex not found
[PKT_SCHED]: Fix datalen check in tcf_simp_init().
[INET]: Uninline the __inet_inherit_port call.
[INET]: Drop the inet_inherit_port() call.
SCTP: Initialize partial_bytes_acked to 0, when all of the data is acked.
[netdrvr] forcedeth: internal simplifications; changelog removal
phylib: factor out get_phy_id from within get_phy_device
PHY: add BCM5464 support to broadcom PHY driver
cxgb3: Fix __must_check warning with dev_dbg.
tc35815: Statistics cleanup
natsemi: fix MMIO for PPC 44x platforms
[TIPC]: Cleanup of TIPC reference table code
[TIPC]: Optimized initialization of TIPC reference table
[TIPC]: Remove inlining of reference table locking routines
e1000: convert uint16_t style integers to u16
ixgb: convert uint16_t style integers to u16
sb1000.c: make const arrays static
sb1000.c: stop inlining largish static functions
...
This adds the low level irq tracing hooks to the powerpc architecture
needed to enable full lockdep functionality.
This is partly based on Johannes Berg's initial version. I removed
the asm trampoline that isn't needed (thus improving performance) and
modified all sorts of bits and pieces, reworking most of the assembly,
etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds stacktrace support for powerpc, which will be needed for
lockdep.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves various definitions used all over the place to parse stack
frames to ptrace.h so only one definition is needed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Lockdep found out that we can occasionally take the device-tree
lock for reading from softirq time (from rtas_token called
by the rtas real time clock code called by the NTP code),
while we take it occasionally for writing without masking
interrupts. The combination of those two can thus deadlock.
While some of those cases of interrupt read lock could be fixed
(such as caching the RTAS tokens) I figured that taking the
lock for writing is so rare (device-tree modification) that we
may as well penalize that case and allow reading from interrupts.
Thus, this turns all the writers to take the lock with irqs
masked to avoid the situation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the __max_memory variable, as it is not referenced anywhere
in the tree besides some code in arch/ppc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The xics code currently has a direct and lpar variant of
xics_host_map, the only difference being which irq_chip they use. If
we remember which irq_chip we're using we can combine these two
routines. That also allows us to have a single irq_host_ops instead
of two.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_mpic_init_IRQ() implements the same logic as the xics code did to
find the i8259 cascade irq. Now that we've pulled that logic out into
pseries_setup_i8259_cascade() we can use it in the mpic code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the xics references from xics_setup_8259_cascade(), and merge the
good bits from the almost identical logic in pseries_mpic_init_IRQ().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code in xics.c to setup the i8259 cascaded irq handler is not really
xics specific, so move it into setup.c - we will clean this up further in
a subsequent patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
IDE PMAC host driver and all IDE PCI host drivers use pci_enable_device()
nowadays so the following quirk in pmac_pcibios_after_init() can be removed.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add special cases for pplus and prep to ide_default_{irq,io_base}()
(+ FIXMEs about the need to use IDE platform host driver instead).
* Remove no longer needed ppc_ide_md and struct ide_machdep_calls.
* Then remove <linux/ide.h> include from:
- arch/powerpc/kernel/setup_32.c
- arch/ppc/kernel/ppc_ksyms.c
- arch/ppc/kernel/setup.c
- arch/ppc/platforms/pplus.c
- arch/ppc/platforms/prep_setup.c
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add pmac_ide_init_ports() helper and use it instead of
pmac_ide_init_hwif_ports().
* Remove ppc_ide_md hooks - no need for them
(IDE pmac host driver takes care of all this setup).
* Then remove no longer needed <linux/ide.h> include
from arch/powerpc/platforms/powermac/pmac.h.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently USB Host isn't functional on the MPC8315E boards, for two
reasons as described below.
MPC8315 Reference Manual says:
"The USB DR unit must have the same clock ratio as the encryption core
unit, unless one of them has its clock disabled."
The encryption core also drives I2C clock, so it is enabled and is equal
to 01. That means USBDRCM should be 01 here.
Plus, according to MPC8315E-RDB schematics, USB unit consumes CLK_IN
clock from the 24.00MHz oscillator, which means we must adjust REFSEL
bits as well.
p.s.
Idially we should rework whole 83xx/usb.c code, in two steps:
1. Move SCCR code to the U-Boot;
2. Implement fsl,usb-clock property in the device tree, so usb.c could
decide what clock exactly to use on per-board basis.
Though, today we're not in a hurry since there is just one 8315e board
out there.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8568E has 64K byte MURAM, so the size should be 0x10000, not 0xc000.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As suggested by Timur Tabi, we match on the old compat node ID for one
version and warn accordingly. If we don't do this, we plunge people who
try to use an old DTB into silent boot death with no clear indication of
what the problem is.
This patch should be removed at the beginning of the 2.6.27 dev cycle.
It is only meant to ease the transition in the short term.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The rheap allocation function, rh_alloc, could call kmalloc with GFP_KERNEL.
This can sleep, which means you couldn't hold a spinlock while called rh_alloc.
Change all kmalloc calls to use GFP_ATOMIC so that it won't sleep. This is
safe because only small blocks are allocated.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/mpc85xx_ads.c: In function ‘init_ioports’:
arch/powerpc/platforms/85xx/mpc85xx_ads.c:168: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds in the device tree source for the SBC8641D, based
largely on the mpc8641_hpcn.dts. The biggest differences are
the lack of a complex IRQ mapping (since no Uli/i8259 cascade)
and the different layout of devices on the localbus node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a sample defconfig for the Wind River SBC8641D
board, with SMP, PCI and NFS root enabled.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the Wind River SBC8641D board, based
largely on the mpc86xx_hpcn support. The biggest difference is
the lack of the Uli and the i8259 cascade, which simplifies things.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. Detect (and bail out on) more conditions that violate the
assumptions of the setup code -- we assume in such cases that the device
tree is correct and reflects what the firmware did.
2. The inbound memory mask calculation was wrong.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
