No 64-bit PPC_MULTIPLATFORM platforms use the mv643xx_eth driver,
so build it only on PPC32.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Sven Luther <sl@bplan-gmbh.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement NAPI changes to pcnet32 driver. Compile default is off.
Listed as experimental.
Len and Don both worked on a NAPI implementation and have both tested
these changes.
An e1000 blasting short packets to the pcnet32 will lockup Don's system
until the receive storm stops. Without NAPI Len's system watchdog would
expire causing the system to reboot. With NAPI the system will stay
operational.
Tested ia32 and ppc64. Tested '970A, '971, '972, '973, '975, '976, and
'978.
The Kconfig changes came from Len. Don is to blame for all the others.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the firmware download URL in Kconfig to match the header
in drivers/net/myri10ge/myri10ge.c.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add NAPI support to the via-rhine driver so that it can handle higher
speeds and doesn't get overloaded by interrupts as easily.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revised version of the forcedeth NAPI support.
This version is based against netdev-2.6#upstream
(after the MAC patches from Ayaz today).
Can't use nv_disable_hw_interrupts because NAPI only wants to
mask off receive irq's and leave the others alone.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a complementary network driver for our ISP4XXX parts.
There is a concurrent effort underway to get the iSCSI driver (qla4xxx)
integrated upstream as well.
I have been through several iterations with the linux-netdev list and have had
much response from Stephen Hemminger.
- Built and tested using kernel 2.6.17-rc4.
- The chip supports two ethernet and two iSCSI functions.
- The functions ql_sem_lock, ql_sem_spinlock, ql_sem_unlock, and
ql_wait_for_drvr_lock are used to protect resources that are shared across
the network and iSCSI functions. This protection is mostly during chip
initialization and resets, but also include link management.
- The PHY/MII are not exported through ethtool due to the fact that the
iSCSI function will control the common link at least 50% of the time.
This driver has been through several iterations on the netdev list and we feel
this driver is ready for inclusion in the upstream kernel.
It has been built and tested on x86 and PPC64 platforms.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert selection of serial line header compression to use CONFIG_SLHC
rather than makefile ifeq uglyness. This makes it easier to select
the SLHC module from other code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (33 commits)
[PATCH] myri10ge - drop workaround pci_save_state() disabling MSI
[PATCH] myri10ge - drop workaround for the missing AER ext cap on nVidia CK804
via-velocity: the link is not correctly detected when the device starts
[PATCH] add b44 to maintainers
[PATCH] WAN: ioremap() failure checks in drivers
[PATCH] WAN: register_hdlc_device() doesn't need dev_alloc_name()
[PATCH] skb_padto()-area fixes in 8390, wavelan
[PATCH] make drivers/net/forcedeth.c:nv_update_pause() static
[PATCH] network driver for Hilscher netx
[PATCH] Dereference in tokenring/olympic.c
[PATCH] Array overrun in drivers/net/wireless/wavelan.c
[PATCH] Remove useless check in drivers/net/pcmcia/xirc2ps_cs.c
[PATCH] 8139cp: add ethtool eeprom support
[PATCH] 8139cp: fix eeprom read command length
[PATCH] b44: update b44 Kconfig entry
[PATCH] b44: update version to 1.01
[PATCH] b44: add wol for old nic
[PATCH] b44: add parameter
[PATCH] b44: add wol
[PATCH] b44: fix manual speed/duplex/autoneg settings
...
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (139 commits)
[POWERPC] re-enable OProfile for iSeries, using timer interrupt
[POWERPC] support ibm,extended-*-frequency properties
[POWERPC] Extra sanity check in EEH code
[POWERPC] Dont look for class-code in pci children
[POWERPC] Fix mdelay badness on shared processor partitions
[POWERPC] disable floating point exceptions for init
[POWERPC] Unify ppc syscall tables
[POWERPC] mpic: add support for serial mode interrupts
[POWERPC] pseries: Print PCI slot location code on failure
[POWERPC] spufs: one more fix for 64k pages
[POWERPC] spufs: fail spu_create with invalid flags
[POWERPC] spufs: clear class2 interrupt status before wakeup
[POWERPC] spufs: fix Makefile for "make clean"
[POWERPC] spufs: remove stop_code from struct spu
[POWERPC] spufs: fix spu irq affinity setting
[POWERPC] spufs: further abstract priv1 register access
[POWERPC] spufs: split the Cell BE support into generic and platform dependant parts
[POWERPC] spufs: dont try to access SPE channel 1 count
[POWERPC] spufs: use kzalloc in create_spu
[POWERPC] spufs: fix initial state of wbox file
...
Manually resolved conflicts in:
drivers/net/phy/Makefile
include/asm-powerpc/spu.h
This is a patch for the Hilscher netx builtin ethernet ports. The
netx board support was merged into 2.6.17-git2.
The netx is a arm926 based SoC.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
--
drivers/net/Kconfig | 11
drivers/net/Makefile | 1
drivers/net/netx-eth.c | 516 ++++++++++++++++++++++++++++++++++++++++
include/asm-arm/arch-netx/eth.h | 27 ++
4 files changed, 555 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Creates new config variables PPC_CELL_NATIVE and PPC_IBM_CELL_BLADE.
The existing CONFIG_PPC_CELL is now used to denote the generic
Cell processor support.
PPC_CELL = make descends into platforms/cell
PPC_CELL_NATIVE = add bare metal support
PPC_IBM_CELL_BLADE = add blade device drivers, etc.
Also renames spu_priv1.c to spu_priv1_mmio.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (109 commits)
[ETHTOOL]: Fix UFO typo
[SCTP]: Fix persistent slowdown in sctp when a gap ack consumes rx buffer.
[SCTP]: Send only 1 window update SACK per message.
[SCTP]: Don't do CRC32C checksum over loopback.
[SCTP] Reset rtt_in_progress for the chunk when processing its sack.
[SCTP]: Reject sctp packets with broadcast addresses.
[SCTP]: Limit association max_retrans setting in setsockopt.
[PFKEYV2]: Fix inconsistent typing in struct sadb_x_kmprivate.
[IPV6]: Sum real space for RTAs.
[IRDA]: Use put_unaligned() in irlmp_do_discovery().
[BRIDGE]: Add support for NETIF_F_HW_CSUM devices
[NET]: Add NETIF_F_GEN_CSUM and NETIF_F_ALL_CSUM
[TG3]: Convert to non-LLTX
[TG3]: Remove unnecessary tx_lock
[TCP]: Add tcp_slow_start_after_idle sysctl.
[BNX2]: Update version and reldate
[BNX2]: Use CPU native page size
[BNX2]: Use compressed firmware
[BNX2]: Add firmware decompression
[BNX2]: Allow WoL settings on new 5708 chips
...
Manual fixup for conflict in drivers/net/tulip/winbond-840.c
Add functions to decompress firmware before loading to the internal
CPUs. Compressing the firmware reduces the driver size significantly.
Added file name length sanity check in the gzip header to prevent
going past the end of buffer [suggested by DaveM].
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
convert au1000_eth driver to use PHY framework and garbage collected
functions and identifiers that became unused/obsolete in the process
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In file included from drivers/net/smc911x.c:84:
drivers/net/smc911x.h:46:9: warning: "SMC_USE_16BIT" is not defined
drivers/net/smc911x.h:60:9: warning: "SMC_USE_32BIT" is not defined
drivers/net/smc911x.h:73:10: warning: "SMC_USE_PXA_DMA" is not defined
drivers/net/smc911x.c: In function `smc911x_reset':
drivers/net/smc911x.c:247: warning: implicit declaration of function `SMC_inl'
drivers/net/smc911x.c:249: warning: implicit declaration of function `SMC_outl'
Cc: Dustin McIntire <dustin@sensoria.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>
> The patch was badly wordwrapped. Please fix and resend.
>
OK, I've fixed the wrapping and removed the CONFIG_ARM restriction. I've also did my
best to modify the C style to conform to the comments.
I noticed that the patch is getting ignored by majordomo due to its size >100K.
Should it be broken up somehow to allow posting to the lists?
Signed-off-by: Dustin McIntire <dustin@sensoria.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
kconfig sanitized around drivers/net
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The spidernet drivers uses request_firmware() and thus needs to select
FW_LOADER.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch contains the following possible updates:
- let FORCEDETH no longer depend on EXPERIMENTAL
- remove the "Reverse Engineered" from the option text:
for the user it's important which hardware the driver supports, not
how it was developed
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve reference to PCI NE2K support in ISA NE2K documentation.
Original 2.4 patch From: Ged Haywood <ged@jubileegroup.co.uk>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This documentation is mostly obsolete, and should therefore either be
updated or removed (this patch does the latter).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>From : Dale Farnsworth <dale@farnsworth.org>
Recent patches for the mv643xx_eth driver now use the MII interface
library. Select MII so it gets built when that driver is selected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Take the experimental dependency of skge driver, it is as stable as the
others.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sk98lin driver was changed a while ago to remove support for the
D-Link 530T card because that hardware has no working VPD data. The help
text for Kconfig was not updated.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch corrects a few spelling and grammar errors found in
drivers/net
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the whole netdevices menu depend on NET, rather than having an empty
submenu when networking is disabled.
Indeed, almost the whole body of the menu was surrounded by if NETDEVICES,
and what was outside depended on NETCONSOLE which is inside the menu.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some users have commented that it is unclear which driver they should be
using for their Marvell/SysKonnect network adapter, and which ones
are/aren't interchangable.
This patch attempts to reduce the confusion.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
*) mark as "EXPERIMENTAL" various items that either aren't very stable or
that are actively crashing the setup of users which don't really need them
(i.e. HIGHMEM and 3-level pagetables on x86 - nobody needs either,
everybody reports "I'm using it and getting trouble").
*) move net/Kconfig near to the rest of network configurations, and
drivers/block/Kconfig near "Block layer" submenu.
*) it's useless and doesn't work well to force NETDEVICES on and to disable
the prompt like it's done. Better remove the attempt, and change that to a
simple "default y if UML".
*) drop the warning about "report problems about HPPFS" - it's redundant
anyway, as that's the usual procedure, and HPPFS users are especially
technical (i.e. they know reporting bugs is _good_).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for the Intel IXDP2351 to the CS89x0 driver.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the help text of the cs89x0 network driver Kconfig entry.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the ColdFire FEC ethernet driver to be enabled on the M520x CPU
family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A new device to do intermidiate functional block in a system shared
manner. To use the new functionality, you need to turn on
qos/classifier actions.
The new functionality can be grouped as:
1) qdiscs/policies that are per device as opposed to system wide. ifb
allows for a device which can be redirected to thus providing an
impression of sharing.
2) Allows for queueing incoming traffic for shaping instead of
dropping.
Packets are redirected to this device using tc/action mirred redirect
construct. If they are sent to it by plain routing instead then they
will merely be dropped and the stats would indicate that.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a wrong indentation.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MIPS dependency for dm9000 ethernet controller. Indeed this controller
is used by some embedded platforms based on MIPS CPUs.
Signed-off-by: Franck Bui-Huu <franck.bui@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PNX010X support for CS89x0 should be conditional on NET_PCI, as it is an 'on
board controller' and NET_PCI includes that category of NICs. Since
ARCH_PNX0105 was recently changed to ARCH_PNX010X, incorporate that change as
well while we're at it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We changed the name of the Kconfig symbols along with
the move to arch/powerpc. This one hunk got lost during
the conversion.
From: Jens.Osterkamp@de.ibm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Eliminate special case for EC-A1. The overhead isn't so
great that having config option is worth it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The way the hardware and firmware work is that there is one shared RX
queue and IRQ for a number of different network interfaces. Due to this,
we would like to process received packets for every interface in the same
NAPI poll handler, so we need a pseudo-device to schedule polling on.
What the driver currently does is that it always schedules polling for
the first network interface in the list, and processes packets for every
interface in the poll handler for that first interface -- however, this
scheme breaks down if the first network interface happens to not be up,
since netif_rx_schedule_prep() checks netif_running().
sky2 apparently has the same issue, and Stephen Hemminger suggested a
way to work around this: create a variant of netif_rx_schedule_prep()
that does not check netif_running(). I implemented this locally and
called it netif_rx_schedule_prep_notup(), and it seems to work well,
but it's something that probably not everyone would be happy with.
The ixp2000 is an ARM CPU with a high-speed network interface in the
CPU itself (full duplex 4Gb/s or 10Gb/s depending on the IXP model.)
The CPU package also contains 8 or 16 (again depending on the IXP
model) 'microengines', which are somewhat primitive but very fast
and efficient processor cores which can be used to offload various
things from the main CPU.
This driver makes the high-speed network interface in the CPU visible
and usable as a regular linux network device. Currently, it only
supports the Radisys ENP2611 IXP board, but adding support for other
board types should be fairly easy.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patch support the SMC9111 present on DB1200 boards.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Matt Domsch <Matt_Domsch@dell.com>
The patch below implements the Microsoft Point-to-Point Encryption method
as a PPP compressor/decompressor. This is necessary for Linux clients and
servers to interoperate with Microsoft Point-to-Point Tunneling Protocol
(PPTP) servers (either Microsoft PPTP servers or the poptop project) which
use MPPE to encrypt data when creating a VPN.
This patch differs from the kernel_ppp_mppe DKMS pacakge at
pptpclient.sourceforge.net by utilizing the kernel crypto routines rather
than providing its own SHA1 and arcfour implementations.
Minor changes to ppp_generic.c try to prevent a link from disabling
compression (in our case, the encryption) after it has started using
compression (encryption).
Feedback to <pptpclient-devel@lists.sourceforge.net> please.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: James Cameron <james.cameron@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
This patch provides dynamic two buffer-mode and 3 buffer-mode options.
Previously 2 buffer-mode was compilation option. Now with this patch applied
one can load driver in 2 buffer-mode with module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=2
This patch also provides 3 buffer-mode which provides header separation
functionality. In 3 buffer-mode skb->data will have L2/L3/L4 headers and
"skb_shinfo(skb)->frag_list->data" will have have L4 payload.
one can load driver in 3 buffer-mode with same above module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=3
Please review the patch.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch replaces current PowerPC 4xx EMAC driver with
new, re-written from the scratch version. This patch is quite big
(~234K) because there is virtualy 0% of common code between old and
new version.
New driver uses NAPI, it solves stability problems under heavy packet
load and low memory, corrects chip register access and fixes numerous
small bugs I don't even remember now.
This patch has been tested on all supported in 2.6 PPC 4xx boards.
It's been used in production for almost a year now on custom
4xx hardware. PPC32 specific parts are already upstream.
Patch was acked by the current EMAC driver maintainer (Matt Porter). I
will be maintaining this new version.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
--
Kconfig | 72
ibm_emac/Makefile | 13
ibm_emac/ibm_emac.h | 418 +++--
ibm_emac/ibm_emac_core.c | 3414 ++++++++++++++++++++++++----------------------
ibm_emac/ibm_emac_core.h | 313 ++--
ibm_emac/ibm_emac_debug.c | 377 ++---
ibm_emac/ibm_emac_debug.h | 63
ibm_emac/ibm_emac_mal.c | 674 +++++----
ibm_emac/ibm_emac_mal.h | 336 +++-
ibm_emac/ibm_emac_phy.c | 335 ++--
ibm_emac/ibm_emac_phy.h | 105 -
ibm_emac/ibm_emac_rgmii.c | 201 ++
ibm_emac/ibm_emac_rgmii.h | 68
ibm_emac/ibm_emac_tah.c | 111 +
ibm_emac/ibm_emac_tah.h | 96 -
ibm_emac/ibm_emac_zmii.c | 255 +++
ibm_emac/ibm_emac_zmii.h | 114 -
17 files changed, 4114 insertions(+), 2851 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
IXDP2x01 systems can be built without PCI network cards, so we should not
require NET_PCI to build CS89x0 on these systems.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The documentation about s2io is available at
Documentation/networking/s2io.txt.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch from Jon Ringle
This patch gives support for the CS8900A ethernet chip on the Comdial MP1000
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch changes pocket and parallel adaptors to depend on PARPORT
instead of ISA in order to get the option in newer SuperIO based systems.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an "Ethernet" driver which sends Ethernet packets over the standard
RapidIO messaging. This depends on the core RIO patch for mailbox/doorbell
access.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Merge of four previous patches and the Kconfig fix
* Remove debug printk's
* whitespace cleanup and version number change
* clear interrupts, reset phy, and reset hardware on shutdown
* ignore 64bit counter overflow interrupts
* fix a couple of places where second port could clobber state
of first port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add configuration support for the FEC ethernet controller in the
Freescale 523x processor family. Also add and option to configure
the second FEC controller on some Freescale processors.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a driver for a new 1000 Mbit ethernet NIC. It is
integrated on the south bridge that is used for our Cell Blades.
The code gets the MAC address from the Open Firmware device tree, so it
won't compile on platforms other than ppc64.
This is the first public release, so I don't expect the first version to
get merged, but I'd aim for integration within the 2.6.13 time frame.
Cc: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sis191 is the gigabit brother of the sis190. SiS's driver suggests
that the register set is backward compatible: this should hopefully
give a basic driver.
The device should allow the usual features from a modern ethernet
adapter (802.1q, SG, Jumbo frames, TSO, checksum offload). So far
the relevant register layout is not documented. SiS's driver does
not provide these features either (at least not for Linux).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch from Sascha Hauer
This patch adds support for setting and getting RTS / CTS via
set_mtctrl / get_mctrl functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SIS190 must select MII since it's using it.
While I was editing the Kconfig entry, I also converted the spaces to
tabs.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
New driver for the Marvell Yukon2 Gigabit Ethernet chipset.
This driver is based on the skge driver, but using the logic
from the SysKonnect version of the sk98lin driver.
It should support all the Yukon2 chipsets that are available
in many current Intel and AMD motherboards.
The driver does support ethtool, tx and rx checksum, and
tcp segmentation offload. But it has only been tested for
a short while and is known to stop receiving under heavy load.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Raise the sis190 driver from the dead
The driver handles the integrated network device found on SiS 965L
chipset. It follows the classical (non-napi) interrupt-driven model
and provides minimal ethtool support.
The code comes from a heavy cleanup/rewrite of the original code
which was removed from the kernel on 14/04/2004. Since the r8169
driver does not work too bad and there will probably be (at least)
a few months of improvements/testing/fixing, I made the code as
close as possible to the r8169 one.
Pascal Chapperon <pascal.chapperon@wanadoo.fr> deserves some special
credit for testing and bug-catching. Many thanks to Lars Vahlenberg
as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Move in_aton to allow netpoll and pktgen to work without the rest of
the IPv4 stack. Fix whitespace and add comment for the odd placement.
Delete now-empty net/ipv4/utils.c
Re-enable netpoll/netconsole without CONFIG_INET
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggestion from Sam Ravnborg <sam@ravnborg.org>
It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
token ring, wireless, PCMCIA, WAN, ATM, and S390.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETCONSOLE=y and INET=n results in the following compile error:
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put NETCONSOLE and NETPOLL options together since they are related.
This cuts down on the hassle of flipping back and forth between
the Networking menu and the Network drivers menu to change their
config settings.
Tested with menuconfig, gconfig, and xconfig.
gconfig has a small problem with this. I think that it's
a bug in gconfig and I will take it up with Romain Lievin.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to provide support for cs89x0-based network device on
Philips' pnx0105 board.
Signed-off-by: dmitry pervushin <dpervushin@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The 8129/8130 support is a sub-option that is not visible if the user
hasn't enabled the 8139 support.
Let's make it a bit easier for users to find the driver for their nic.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
A new driver bnx2 for Broadcom bcm5706 is available.
The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h
Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Linux driver for the Chelsio 10Gb Ethernet Network Controller by Chelsio
(http://www.chelsio.com). This driver supports the Chelsio N210 NIC and is
backward compatible with the Chelsio N110 model 10Gb NICs. It supports
AMD64, EM64T and x86 systems.
Signed-off-by: Tina Yang <tinay@chelsio.com>
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Adrian said:
- my3126.c is unused (because t1_my3126_ops isn't used anywhere)
- what are the EXTRA_CFLAGS in drivers/net/chelsio/Makefile for?
- $(cxgb-y) in drivers/net/chelsio/Makefile seems to be unneeded
- completely unused global functions:
- espi.c: t1_espi_get_intr_counts
- sge.c: t1_sge_get_intr_counts
- the following functions can be made static:
- sge.c: t1_espi_workaround
- sge.c: t1_sge_tx
- subr.c: __t1_tpi_read
- subr.c: __t1_tpi_write
- subr.c: t1_wait_op_done
shemminger said:
The performance recommendations in cxgb.txt are common to all fast devices,
and should be in one file rather than just for this device. I would rather
see ip-sysctl.txt updated or a new file on tuning recommendations started.
Some of them have consequences that aren't documented well.
For example, turning off TCP timestamps risks data corruption from sequence wrap.
A new driver shouldn't need so may #ifdef's unless you want to putit on older
vendor versions of 2.4
Some accessor and wrapper functions like:
t1_pci_read_config_4
adapter_name
t1_malloc
are just annoying noise.
Why have useless dead code like:
/* Interrupt handler */
+static int pm3393_interrupt_handler(struct cmac *cmac)
+{
+ u32 master_intr_status;
+/*
+ 1. Read master interrupt register.
+ 2. Read BLOCK's interrupt status registers.
+ 3. Handle BLOCK interrupts.
+*/
Jeff said:
step 1: kill all the OS wrappers.
And do you really need hooks for multiple MACs, when only one MAC is
really supported? Typically these hooks are at a higher level anyway --
struct net_device.
From: Christoph Lameter <christoph@lameter
Driver modified as suggested by Pekka Enberg, Stephen Hemminger and Andrian
Bunk. Reduces the size of the driver to ~260k.
- clean up tabs
- removed my3126.c
- removed 85% of suni1x10gexp_regs.h
- removed 80% of regs.h
- removed various calls, renamed variables/functions.
- removed system specific and other wrappers (usleep, msleep)
- removed dead code
- dropped redundant casts in osdep.h
- dropped redundant check of kfree
- dropped weird code (MODVERSIONS stuff)
- reduced number of #ifdefs
- use kcalloc now instead of kmalloc
- Add information about known issues with the driver
- Add information about authors
Signed-off-by: Scott Bardone <sbardone@chelsio.com>
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
diff -puN /dev/null Documentation/networking/cxgb.txt
This patch adds support for the davicom dm9000 network driver. The dm9000
is found on some embedded arm boards such as the pimx1 or the scb9328.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
diff -puN /dev/null drivers/net/dm9000.c
This patch fixes the following compile error caused by bk-netdev:
<-- snip -->
...
LD .tmp_vmlinux1
drivers/built-in.o(.text+0x98528): In function `sis900_get_settings':
: undefined reference to `mii_ethtool_gset'
drivers/built-in.o(.text+0x98538): In function `sis900_set_settings':
: undefined reference to `mii_ethtool_sset'
drivers/built-in.o(.text+0x98517): In function `sis900_get_link':
: undefined reference to `mii_link_ok'
drivers/built-in.o(.text+0x98547): In function `sis900_nway_reset':
: undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Daniele Venzano <venza@brownhat.org>
The options FMV18X and SK_G16 do depend on the non-available
CONFIG_OBSOLETE even in kernel 2.4 - IOW, the last time it was able to
select them was in kernel 2.2 (or even before).
Since it seems noone misses these drivers, this patch removes them.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Drivers that expect ISA DMA API are marked as such in Kconfig.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows Kconfig to build the MV643xx ethernet driver on Pegasos
(CONFIG_PPC_MULTIPLATFORM) and adds what I think is a missing fix from
Dale's batch, that is remove SA_INTERRUPT and add SA_SHIRQ in there as the
interrupt is shared if I understand things correctly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!